Page 1
Specifications are subject to change without notice (15.01.03) 1
Product Description
The PD32CNG05 sensor
family comes in a compact
12 x 32 x 20 mm reinforced
PMMA/ABS-housing.
The sensors are useful in
applications where highaccuracy detection as well as
small size is required.
The Teach-In function for
adjustment of the sensitivity
makes the sensors highly
flexible. The output type is
preset (NPN or PNP), and the
output switching function is
programmable (NO or NC).
• Miniature sensor range
• Range: 0.5 m, with reflector
• Sensitivity adjustment by Teach-In programming
• Modulated, red light 660 nm, polarized
• Supply voltage: 10 to 30 VDC
• Output: 100 mA, NPN or PNP preset
• Make and break switching function programmable
• LED for output indication, signal stability and power ON
• Protection: reverse polarity, short circuit and transients
• Cable and plug versions
• Compact housing
• Excellent EMC performance
Photoelectrics
Retro-reflective, for transparent Objects
Type PD32CNG05
Type Selection
Housing Range Ordering no. Ordering no.
W x H x D S
n
NPN & PNP cable NPN & PNP plug
Make & break switching Make & break switching
12 x 32 x 20 mm 0.5 m PD 32 CNG 05 NPT PD 32 CNG 05 NPM5T
PD 32 CNG 05 PPT PD 32 CNG 05 PPM5T
Specifications
Rated operating distance (Sn) Up to 0.5 m,
with reflector 51 x 51 mm
Sensitivity Adjustable by Teach-In
(push button or wire)
Temperature drift ≤ 1%/ºC
Hysteresis (H)
(differential travel) ≤ 10%
Rated operational volt. (U
B
) 10 to 30 VDC
(ripple included)
Ripple (U
rpp
) ≤ 10%
Output current
Continuous (I
e
) ≤ 100 mA
Short-time (I) ≤ 100 mA
(max. load capacity 100 nF)
No load supply current (I
o
) ≤ 25 mA @ 24 VDC
Minimum operational current (Im)
0.5 mA
OFF-state current (I
r
) ≤ 100 µA
Voltage drop (U
d
) ≤ 2.4 VDC @ 100 mA
Protection
Short-circuit, reverse polarity
and transients
Light source GaAlAs, LED, 660 nm
Light type Red, modulated
Sensing angle ± 2º
Ambient light 5,000 lux
Light spot 20 x 20 mm @ 500 mm
Operating frequency 1000 Hz
Response time
OFF-ON (t
ON
) ≤ 0.5 ms
ON-OFF (t
OFF
) ≤ 0.5 ms
Power ON delay (t
v
) ≤ 300 ms
Output function
NPN and PNP Preset
NO/NC switching function Set up by button
External Teach
Same function as button 10 to 30 VDC
Locked (disable teach button) 0 to 2,5 VDC
Operating mode Not connected
Indication
Output ON LED, yellow
Signal stability ON and power ON
LED, green
Environment
Installation category II (IEC 60664/60664A;
60947-1)
Ordering Key
Type
Housing style
Housing size
Housing material
Housing length
Detection principle
Sensing distance
Output type
Output configuration
Connection type
Teach-In
PD32CNG05PPM5T
Page 2
Operation Diagram
2 Specifications are subject to change without notice (28.08.02)
Dimensions
PD32CNG05
Specifications (cont.)
Pollution degree 3 (IEC 60664/60664A;
60947-1)
Degree of protection IP 67 (IEC 60529; 60947-1)
Ambient temperature
Operating
-20°to +60°C (-4°to +140°F)
Storage -20°to +80°C (-4°to +176°F)
Vibration 10 to 55 Hz, 0.5 mm/7.5 g
(IEC 60068-2-6)
Shock 30 g / 11 ms, 3 pos, 3 neg
per axis
(IEC 60068-2-6, 60068-2-32)
Rated insulation voltage 500 VAC (rms)
Housing material
Body ABS, black
Front material PMMA, red
Connection
Cable PUR, black, 2 m
4 x 0.14 mm
2
, Ø = 3.6 mm
Plug M8, 4-pin
Weight With cable: 40 g
With plug: 10 g
CE-marking Yes
Approval cUL
Plug version
Cable version
Wiring Diagrams
+
-
1 BN
4 BK
2 WH
3 BU
NPN
PNP
tv = Power ON delay
Power supply
Object/target present
Break (NC) Output ON
Make (NO) Output ON
Teach input is active when
2 WH wire is connected to
V+ (1 BN).
+
-
1 BN
4 BK
2 WH
3 BU
V
V
Page 3
Specifications are subject to change without notice (28.08.02) 3
Delivery Contents
• Photoelectric switch: PD 32 CNG 05 ...
• Installation instruction
• Packaging: Cardboard box
Signal Stability Indication
Excess gain
Time
150%
100%
70%
Green LED ON
Yellow LED ON
Accessories
PD32CNG05
Installation Hints
Relief of cable strain Protection of the sensing face Switch mounted on mobile carrierTo avoid interference from inductive voltage/
current peaks, separate the prox. switch power cables from any other power cables, e.g.
motor, contactor or solenoid cables
Incorrect
Correct
The cable should not be pulled
A proximity switch should not serve as
mechanical stop
Any repetitive flexing of the
cable should be avoided
6.5
ø6.5
R4
ø6.5
10
12
32
20
6.25
20
67
R2.25
50
21
9
ø4.5
4.5
16.5
35
ø4.5
R4
R4
2
R28
4.5
20°
90°
13°
Signal level
Mounting bracket APD32-MB3
For further information refer to “Accessories”
Page 4
4 Specifications are subject to change without notice (25.10.02)
Adjustment
Sensitivity adjustment, with static object
1. Line up the sensor with the reflector. Yellow LED and
green LED are ON.
2. Press the button for 3 s until both LED’s flash
simultaneously (the first switching point is stored).
3. Press the button again for 1 s.
a) The green LED flashes and stays ON: the
second switching point is stored, and the sensor
is ready to operate.
b) Both LED’s flash simultaneously: the sensor
cannot detect the object, no switching points
are stored.
Sensitivity adjustment, with a running process
1. Line up the sensor with the reflector. Green LED is ON.
At this stage the status of the yellow LED can be
ignored.
2. The running process must be the only “object” within
the detection area. Press the button for 3 s until both
LED’s flash simultaneously.
3. Press the button for at least the duration of one process cycle.
a) The green LED flashes and stays ON: both
switching points have been stored, and the sensor is ready to operate.
b) Both LED’s flash simultaneously: the sensor
cannot detect the object, no switching points
are stored.
Programming of make and break switching function
1. Press the button for 13 s.
Both LED’s flash alternately.
2. Release the button: the green LED flashes.
3. While the green LED flashes, the output is inverted
each time the button is pressed. This is indicated by
the yellow LED.
When the button is not pressed for 10 s, the current
output function is stored.
The sensor is now ready for operation.
Default setting
1. Cover light emitter and receiver: Press the button for
3 s, until both LED’s flash simultaneously.
2. Keep light emitter and receiver covered:
Press the button for 1 s.
The sensor is set to maximum sensitivity.
NB! The Teach Input (2 WH) will work similarly to the push
button, active High.
PD32CNG05
3 s
1 cycle
13 s
3 s
1 s
3 s
1 s
1
23
4
Loading...