Carl Goldberg GBGA1081 User Manual

1

TTiiggeerr 440000

WARNING

A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep
this kit out of the reach of younger children, as it contains parts that could be dangerous. A radio­controlled model is capable of causing serious bodily injury and property damage. It is the buyer's
responsibility to assemble this aircraft correctly and to properly install the motor, radio, and all other
equipment. Test and fly the finished model only in the presence and with the assistance of another
experienced R/C flyer. The model must always be operated and flown using great care and common
sense, as well as in accordance with the Safety Code of the Academy of Model Aeronautics (5151
Memorial Drive, Muncie, IN 47302, 1-800-435-9262). We suggest you join the AMAand become prop­erly insured prior to flying this model. Also, consult with the AMA or your local hobby dealer to find an
experienced instructor in your area. Per the Federal Communications Commission, you are required
to use only those radio frequencies specified "for Model Aircraft."

LIMITED WARRANTY

Carl Goldberg Products, Ltd. has inspected and certified the components of this aircraft. The comp any urges the buyer to perform
his own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their
intended use. The company warrants replacement of any such components, provided the buyer requests such replacement with­in a period of 90 days from the date of purchase and provided the defective part is returned, if so requested by the company.

No other warranty, expressed or implied, is made by the company with respect to this kit. The buyer acknowledges and under­stands that it is his responsibility to carefully assemble the finished flying model airplane and to fly it safely. The buyer hereby
assumes full responsibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the
components of this kit.

CARL GOLDBERG PRODUCTS, LTD.

P.O. Box 88 Oakwood GA 30566 Phone #[phone] Fax # [phone] www.carlgoldbergproducts.com

2

USING THIS INSTRUCTION MANUAL

Before you begin assembling your Tiger 400 ARF, take
some time to read through this entire instruction book. It is
designed to take you step-by-step through the process and
to give you added information on motor and radio selection
and set-up, balancing your aircraft, and flying your model.
The time you spend will speed the assembly process and
help you avoid problems.

PREPARING FOR ASSEMBLY

You will need a work area of approximately 24 x 48" which has
been covered to protect it from adhesive, as well as cu ts a nd
other damage. Many people cover their work area with a
sheet of dry wall (sheet rock) and/or waxed paper to pre­vent CA Glue and Epoxy from ruining the work surface.

CONSTRUCTION TIPS

IMPORTANT: ALWAYS READ A FEW STEPS AHEAD.
This will alert you to coming instructions and will help you
plan accordingly.

Using the Parts Identification section, familiarize yourself
with the various items included in your kit box.

Do not hesitate to ask questions. Your local hobby dealer
and area flyers will most likely be happy to help, as they
want you to have a successful flying experience.

You may also receive technical assistance from Carl
Goldberg Products, Lt d. via e-mail (questions@carlgoldberg­products.com) or by telephone [phone].

ADHESIVES & GLUING TECHNIQUES

CA adhesives are specially formulated to firmly glue the
plywood, hardwood, and balsa used in your model and to
withstand the vibration and stresses of high performance
flight. However, there are times, such as when you are
installing the stabilizer and fin on the fuselage and want
more set-up time for careful alignment and positioning,
then you should use epoxy. Occasionally, you also will
want to use thin CA, which "wicks" into the surrounding
areas. Aliphatic resin glue or similar water-based glues can
also be used, but they will add to the assembly time
because they dry so much more slowly than CA glue.
Remember, when ever using any CA, you must be careful
to read instructions thoroughly, as you will have only sec­onds for positioning of parts. Be sure to trial fit parts
together before gluing. Also, never use watery THIN type
CAglue for gluing plywood and hardwood parts. Thin CA's
do not adequately bond these areas.

CAUTION

Some people may experience an allergic reaction when
exposed to fumes from CA glue or epoxy. As with paints,
thinners, and solvents, it is always important to use glues
only where there is adequate ventilation to carry fumes
away. A fan is recommended. Also, special care must be
taken when using CA, as it will bond skin as well as other
surfaces. Before using any CA, carefully read all label pre­cautions. When using CA, protective eye-wear and care in
keeping the glue away from the face is highly recommend­ed. If CA does happen to get into the eye, hold lid open
and flush with water only. Seek immediate medical atten­tion.

COVERING

The Tiger 400 ARF is covered in a premium polyester film
chosen by many of the world's top flyers for its beauty,
toughness, and ease of application and repair. It is not
uncommon for ARF's to develop a few wrinkles in transit. If
this is true of your model, the situation is easily corrected.
Before you begin putting the pieces together, run around
the edge of the seams first then over the surface of each
section with an iron (either specially designed for airplane
use or the more cumbersome household iron). Apply the
heat (set at about 350° F), following along with a soft cloth
and pressing down on the covering as you go around. This
will more firmly set the covering adhesive into the wood
and keep your aircraft covering tight and smooth in the
future. Once you have ironed the seams stay away from
them with the heat or the covering will slide when you try
to shrink the middle. If this happens the wrinkles will not
come out of the covering.

One of the great advantages of polyester film is that it can
be applied over itself without causing gas bubbles. This
allows you to repair your aircraft, as well as to customize it
in a number of ways. If, due to a flight mishap, you get a
hole or similar covering damage, simply trim away the
ragged edges and then apply a patch, following the direc­tions that come with your covering , which is available at
your hobby dealer.

The Tiger 400 covering can be matched using

Oracover Cub Yellow
Oracover White 870

3

ITEMS NEEDED TO COMPLETE THIS AIRCRAFT

! 1 RADIO GUIDANCE SYSTEM (4 CHANNEL

MINIMUM REQUIRED WITH 4 SERVOS)

! 1 6” SERVO “Y” HARNESS
! 1 ELECTRONIC SPEED CONTROL

(ELECTRIC FLY C-20 FROM GREAT
PLANES SUGGESTED)

! 1 NIMH 8C 1100AAA BATTERY (2 OR 3 CELL

1500 MAH LI-PO BATTERY SUGGESTED)

! 4 MINI- PUSHROD CONNECTORS
! 1 CA ACCELERATOR
! 1 1 OZ. BOTTLE CA MEDIUM GLUE
! 1 1/2 OZ. BOTTLE CA THIN GLUE

! 1 5 MINUET EPOXY
! 1 1/4” FOAM RUBBER

TOOLS AND SUPPLIES FOR ASSEMBLY.

! MODELING OR UTILITY KNIFE
! WORK SURFACE (24" X48")
! SMALL STANDARD & PHILLIPS SCREW-

DRIVERS

! MASKING TAPE
! NEEDLE NOSE PLIERS
! 24” RULER
! FLEXIBLE STRAIGHT-EDGE
! 30-60-90° x 6" TRIANGLE
! SOFT PENCIL
! A FEW STRAIGHT OR "T" PINS
! WIRE CUTTER (DYKES)
! OPTIONAL HEAT GUN/COVERING IRON
! ACID BRUSH
! 5 FT. LENGTH OF STRING

Caution:

Before starting, care-

fully go over all high

stress areas with an

epoxy or wood glue to

confirm all areas are

well glued.