Carl Goldberg GBGA1044 User Manual

1

INSTRUCTIONS

WARNING

A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep
this kit out of the reach of younger children, as it contains parts that could be dangerous. A radio­controlled model is capable of causing serious bodily injury and property damage. It is the buyer's
responsibility to assemble this aircraft correctly and to properly install the motor, radio, and all other
equipment. Test and fly the finished model only in the presence and with the assistance of another
experienced R/C flyer. The model must always be operated and flown using great care and common
sense, as well as in accordance with the Safety Code of the Academy of Model Aeronautics
(www.modelaircraft.org). We suggest you join the AMA and become properly insured prior to flying this
model. Also, consult with the AMA or your local hobby dealer to find an experienced instructor in your
area. Per the Federal Communications Commission, you are required to use only those radio frequen­cies specified "for Model Aircraft."

LIMITED WARRANTY

Carl Goldberg Products has inspected and certified the components of this aircraft. The company urges the buyer to perform his
own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their
intended use. The company warrants replacement of any such components, provided the buyer requests such replacement with­in a period of 90 days from the date of purchase and provided the defective part is returned, if so requested by the company.

No other warranty, expressed or implied, is made by the company with respect to this kit. The buyer acknowledges and under­stands that it is his responsibility to carefully assemble the finished flying model airplane and to fly it safely. The buyer hereby
assumes full responsibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the
components of this kit.

CARL GOLDBERG PRODUCTS, LTD.

P.O. Box 818 Oakwood GA 30566 Phone #[phone] Fax # [phone] www.carlgoldbergproducts.com

© Copyright 2006 Carl Goldberg Products LTD

TM

67” YAK 54

2

Congratulations on your purchase of the
67”Yak 54 ARF. Every effort has been made to
produce a lightweight, straight, easy to assem­ble aircraft. Because of its oversize control sur­faces which are double beveled to allow for
extreme throws, great care must be taken in the
set-up and flying of this airplane. Quality hard­ware components have been provided to allow
for 3D set-up while maintaining adequate
mechanical advantage to eliminate flutter. It is
your responsibility as an advanced pilot to fly
the aircraft in an intelligent manner. THROTTLE

MANAGEMENT IS A MUST!!!!!!! Carl
Goldberg Products has flown the 67”Yak 54
ARF through a very rigorous flight-testing

schedule and have stressed the airframe
beyond all practical parameters without a single
failure. Carl Goldberg Products will NOT

war­ranty the 67”Yak 54 ARF against flutter due to
improper set-up or excessive speed maneuvers.
having said that, we believe you will find the
67”Yak 54 ARF to be one of the most respon­sive, in-the-grove aircraft on the market. Just
remember to use common sense when flying
this high performance machine.

We are very proud of the construction of the
67”Yak 54 ARF and all of our other ARF aircraft.
Each aircraft is jig built to insure a straight true
airframe. Every effort is made to build as light an
aircraft as possible. As with any professional
builder, glue is used sparingly. Please take a

moment during assembly and run a bead of
CA or aliphatic resin into the high stress
joints that you can reach such as the landing
gear plate, servo mounting trays, wing hold
down blocks, Firewall, etc. Also, during the

course of shipping from the manufacturer to our
facility in the United States, it is not uncommon
for the aircraft to experience several changes in
climate. This may cause the iron-on covering to
develop wrinkles. This is not a fault of the manu­facturer. Please take a few minutes with your
heating iron and iron down the seams and re­shrink the covering where needed. The results
will be a beautiful aircraft with a breathtaking fin­ish that you will be proud to display at your flying
club.

Before beginning assembly of your 67”Yak 54
ARF, we highly recommend that you study this
manual in its entirety. You should begin planning
your radio installation based on your choice of
engine and equipment from the beginning.

Because the 67”Yak 54 ARF is intended for
those with some degree of modeling experi­ence, every minute detail will not be cov­ered. This is not a basic trainer. Assembly of
this aircraft will be easy for the experienced
modeler, and by following the instructions
within this manual and using the skills
you’ve gained during your modeling career
you will be able to produce a first class air­craft.

Building supplies needed

Hobby knife w/#11 blades
Thin CA
Medium CA
Canopy glue
30 minute epoxy
Thread lock
Diagonal wire cutters
Pliers
Assorted drill bits
Various sized screwdrivers( both Phillips and
standard head)
Tape measure
Dry-erase marker
Paper towels
Rubbing alcohol
Electrical tape
4-40 Tap & Die Set
3/32, 7/64, 9/64 & 3mm Allen wrench
Wax Paper
3-1 Oil

Note:

Thread lock must be used where
ever any machine bolts are threading
into any type of nuts. If you do not
use thread lock the bolts could
become loose and fall out in flight.

3

ADHESIVES & GLUING TECHNIQUES

CA adhesives are specially formulated to firmly glue the
plywood, hardwood, and balsa used in your model and to
withstand the vibration and stresses of high performance
flight. However, there are times, such as when you are
installing the stabilizer and fin on the fuselage and want
more set-up time for careful alignment and positioning,
then you should use epoxy. Occasionally, you also will
want to use thin CA, which "wicks" into the surrounding
areas. Aliphatic resin glue or similar water-based glues can
also be used, but they will add to the assembly time
because they dry so much more slowly than CA glue.
Remember, when ever using any CA, you must be careful
to read instructions thoroughly, as you will have only sec­onds for positioning of parts. Be sure to trial fit parts
together before gluing. Also, never use watery THIN type
CA glue for gluing plywood and hardwood parts. Thin CA's
do not adequately bond these areas.

CAUTION

Some people may experience an allergic reaction when
exposed to fumes from CA glue or epoxy. As with paints,
thinners, and solvents, it is always important to use glues
only where there is adequate ventilation to carry fumes
away. A fan is recommended. Also, special care must be
taken when using CA, as it will bond skin as well as other
surfaces. Before using any CA, carefully read all label pre­cautions. When using CA, protective eye-wear and care in
keeping the glue away from the face is highly recommend­ed. If CA does happen to get into the eye, hold lid open
and flush with water only. Seek immediate medical atten­tion.

CONSTRUCTION TIPS

IMPORTANT: ALWAYS READ A FEW STEPS AHEAD.
This will alert you to coming instructions and will help you
plan accordingly.

COVERING

The 67”Yak 54 ARF is covered in a premium polyester
film chosen by many of the world's top flyers for its beau­ty, toughness, and ease of application and repair. It is not
uncommon for ARF's to develop a few wrinkles in transit.
If this is true of your model, the situation is easily correct­ed. Before you begin putting the pieces together, run
around the edge of the seams first then over the surface
of each section with an iron (either specially designed for
airplane use or the more cumbersome household iron).
Apply the heat (set at about 350° F), following along with
a soft cloth and pressing down on the covering as you go
around. This will more firmly set the covering adhesive
into the wood and keep your aircraft covering tight and
smooth in the future. Once you have ironed the seams
stay away from them with the heat or the covering will
slide when you try to shrink the middle. If this happens the
wrinkles will not come out of the covering.

ITEMS NEEDED TO COMPLETE THIS AIRCRAFT

 1 24” FUEL LINE
 1 ENGINE .90 TO 1.20 4-STROKE.

 1 RADIO GUIDANCE SYSTEM
 2 12” AILERON SERVO EXTENSION WIRES
 2 Y-HARNESS

 1 CA ACCELERATOR
 1 2 OZ. BOTTLE CA MEDIUM GLUE
 1 1/2 OZ. BOTTLE CA THIN GLUE
 1 30 MINUET EPOXY
 1 1/2” FOAM RUBBER
 1 3” SPINNER

OPTIONAL:

 1 PILOT FIGURE
 8 SERVO ARM EXTENSIONS

NOTE: The 67”Yak 54 ARF covering closely

matches Ultracote:

#872 Bright Yellow

#874 Black

#885 Midnight Blue

#866 True Red

#870 White

3.  Using a 1/8” drill, drill half way through the

aileron hole from both top and bottom till the

drill passes through the aileron.

 Insert the 4-40 x 3” allen head bolt into the top

of the aileron.

 Thread the bolt all the way till the head is flush

with the top of the aileron.

4.

 On the bottom of the aileron, place first the

cup washer then the nylon nut onto the 4-40

bolt.

 Using a 3 mm metric allen wrench tighten the

nylon nut all the way down till it rest in the cup

washer and is tight to the aileron.

 Thread the nylon adjustable control horn onto

the bolt.(Note: Thread the side that you can

see the cut threads in the nylon onto the

bolt)

2.  With the aileron servo in place, make a mark

on the aileron at a 90º degree angle to the

trailing edge and in line with the servo. Look

for the control horn hard point under the cov-

ering. This is the location for the control horn.

4

AILERON CONTROL HORN INSTALLATION

1.  Collect the following items

(2) 2-56 Metal Clevis
(2) 2-56 Hex Nut
(2) Clevis retainers
(2) 2-56 x 6" Threaded Wire

(2) 4-40 x 3” socket head bolt

(2) Nylon Adjustable Control horns

(2) Nylon Nut
(2) Nylon Cup Washer
(2) Nylon swing in keepers

CONTROL HORN PART NAMES

Wing Tip

4-40 bolt

nylon washer

nylon nuts

horn fittings

swing in keepers

WING ASSEMBLY

5

2.  Locate the pre-drilled aileron hinge holes in

both wing halves. Using a 3/16” drill, drill each
hole 1/8” deep. This will allow the center of
the hinge to be inserted half way into each of
the surfaces.

 Repeat this process with the ailerons, making

sure all hinges insert half way

.

3.  Place 1 drop of oil on each of the hinge joints

at the center. This is to keep the hinges loose
and prevent epoxy from sticking at the joint.

Caution: Do not get any oil on the length of the

hinge or it will not glue into the surface.

AILERON INSTALLATION

1.  Collect the following parts:

(1) Left wing
(1) Right wing
(1) Left aileron
(1) Right aileron
(10) hinges
(2) 1/4-20 nylon wing bolts

4.  Select the aileron for the wing half on which

you are working.

 Mix up a liberal amount of 30 minute epoxy.

Using a piece of wire or a toothpick, work some

epoxy into each hole on the wing and aileron.

 Working with 1 hinge at a time, place a dab of

epoxy and insert the hinge half way into one of

the aileron holes.

 Repeat for each of the other hinges for that

aileron.

5.

 Working quickly, place some epoxy on the

second half of each hinge and insert the

aileron into the wing.

 Slide the aileron toward the wing until no gap

remains between the aileron and the wing.

 When satisfied with the alignment, flex the

aileron up and down to confirm that the hinges

are working freely. remove any excess epoxy.

 Apply a few strips of masking tape to keep the

pieces in place.

 Allow to dry before flexing the aileron.

6.

 Repeat the above steps for the other half of

the wing.

AILERON SERVO INSTALLATION

1.  Collect the following parts:

(1) Left wing
(1) Right wing
(2) Servos
(2) 12” Servo Extension
(1) Servo “Y” Harness

2.  Locate the servo hole in the bottom of wing.

 Carefully cut the covering over the servo

holes.

6

3.  Attach the 12” servo extension to the servo.

IMPORTANT! To ensure that any connections locat-

ed inside the wing will not come loose, either when
the wires are pulled, or during flying, always tape

them securely together with electrical tape.

4.  Starting from the servo hole, insert the servo

extension and the servo wire into the servo
hole.

 Allow the wire to fall straight down through

though the wing till it exits the root rib.

5.

 Tape the end of the plug to the root rib.
 Repeat for the other wing half.

Aileron Servos Pushrods

1. Collect the following items:

(2) nylon swing in keepers
(2) 2-56 pushrods threaded one end
(2) 2-56 clevis
(2) silicone clevis retainers

2.  Slide the silicone keeper on the clevis

 Screw the 2-56 pushrod into the clevis so

1/16” of threads extend past the opening

 Attach the clevis to the connector on the

aileron horn.

1/16”

3.  Center the aileron servo and make sure the

aileron is aligned with the wing at the root end.

 Make a mark where the pushrod crosses the

servo control arm.

7

4.  Bend the pushrod 90 degrees at the location

of your mark.

 Cut the remaining wire leaving 3/8”.

3/8”

5.  Install the nylon swing in keeper to attach the

pushrod.

 Repeat for the other aileron.