Only for US market (ETL Sanitation): The equipment shall be installed with backflow protection to
comply with applicable federal, state and local codes.
STARTING UP
ON
OFF
Power ON the machine by means of the main switch inside the machine and then close the front door. (pic. A)
After checking that the machine door is closed and the ground bin and the drip tray are inserted, press the key No.8
(ON/OFF) to turn ON the machine ( PIC. A ).
(FOR SELF CONFIGURATION , press the key n°8 (on/off ) and then insert the waiter password 61111).
When the boiler temperature of 50°C (122°F) is reached, the machine carries out a group rinsing. The display shows:
When the set-up temperature is reached, the keypad lights are on and the display shows:
For machine configuration Standard or Self:
A) Power on the machine by means the main switch
Inside the machine .
Pic. A
Pic. A
G.AUTO CLEANING
SELECT DRINK
To switch OFF the machine press key n°11- Info (Pic.A) and then press key n° 8-Off (Pic.B).
SELECT DRINK
Pic. A Pic. B
2xEspresso Americano
Cappuccino Latte Macchiato
Choco Mocha
Espresso Caffè latte
Coffee temperature
Steam temperature
XXX °C
YYY °C
FILL IN BEAN HOPPER AND CANISTER
Fill in the required amount for daily consumption in order to keep coffee and product always fresh.
DISPLAY THE AVAILABL
E
machineinSELECTDRINK
with the machineinSELECTDRINKmodeto
Where XXX indicates the coffee boiler temperatureandYYYindicates
AND BOILERS TEMPERAT
shift
boilers temperature
SELECT DRINK
Press the SHIFT key with the
Press the INFO key
SHIFT DRINK SELECTIONS
mode to display the available
2xEspresso Americano
Cappuccino Latte Macchiato
Choco Mocha
Espresso Caffè latte
display the
COFFEE TEMPERATURE
STEAM TEMPERATURE
XXX
YYY
the steam boiler temperature.
URE
drink selections :
:
1) COFFEE/CAPPUCCINO/CHOCO DISPENSING
dispenser to the correct heightandplaceacupunderitthenpressthedesireddosekey.
key first and thenthedesireddosekey.
For Waiters’ Card place the smart card abovetheproperreaderbeforepressingthedosekey.
Where “XXXXXXXX” indicates the selected dosekeyname.
The cursor indicates the amount of drink beingdispensed.
Pressing the same dose key during dispensingcanstoptheselecteddose(notavailableforSelfconfigu
Place a cup under the hot water outlet, and pressthehotwater
programmed dose is over. The display shows:
he same dose key during dispensingmaystoptheselecteddose
Hot water cannot be dispensed simultaneouslywithsteam.
By releasing the pressed key, dispensing willbestopped.
ration).
Dispensing will be automaticallystoppedoncethe
(not available for Self configuration).
ted, the machine will automaticallycancelthisfunctionafter
milk will start being dispensed,thedisplayshows:
Adjust the coffee
For Shift doses, press Shift
The display shows:
PLEASE NOTE:
2) HOT WATER DISPENSING
PLEASE NOTE:
• Pressing t
•
Adjust the coffee dispenser
- Pour in the powdered coffee
- Close the decaffeinated door
-
The selected dose wi
PLEASE NOTE:
•
•
Press any milk-based key
SELECT DRINK
Espresso
DISPENSING
XXXXXXX
dose key . .
HOT WATER
XXXXXXX
or steamed
EXTRAMILK
STEAM WAND USE AND CLEANING
1► Before using the steam wand press
the steam button to purge the nozzle.
4► After using the steam wand press
the steam button to purge the nozzle
STEAM WAND NOT AVAILABLE FOR MACHINE IN SELF CONFIGURATION
2► Use the steam wand to foam or heat
any liquid into the jug by handling the
rubber protection.
5► Clean the steam wand by means of a
cloth
3► Press the steam button to stop the
delivery before removing the jug.
6► DO NOT leave the steam wand into
any liquid at any time
WE STRONGLY RECOMMEND TO USE AND CLEAN THE STEAM WAND AS ABOVE SHOWN
AUTOMATIC CLEANINGO
AT THE END OF EACH WORKING DAY , AND/
RECOMMEND TO CARRY OUT AUTOMATICCLEANINGOFTHECOFFEEGROUP,THEMIXERANDTHEMILKFROTHER
1
►
4
►
7
►
POWER CLEANER
Start
Start
F COFFEE GROUP-
MIXER AND MILK FROTH
OR IN CASE THE MACHINE WILL NOT BE USED SOMETIME,WESTRONGLY
2
►
ress
Insert theblackpipesupportinto
the holeinthedriptraygridpress
orcleaning
Start
5
►
9
►
Cleanthegroupfromanycoffee
residues.Thencleanthegroupfiltersby
means ofacloth
GROUPCLEANING
POWER CLEANER
6
►
Keep
seconds.
( for SELFconfigurationinsertthewaiter
password61111).
POWER CLEANER
ER
Keep Shift key pressed for five
seconds.
( for SELF configuration insert the waiter
password 61111).
Press Start key to confirm.
Remove the silicone tube from the
milk box and place it into the
black support press start for
cleaning
Press Start key to confirm the group
cleaning cycle
MIXER CLEANING
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Press Start key to perform the group
cleaning cycle. Press Skip key to skipping
the Power Cleaner and carry out the next
cleaning
Press Start for cleaning
Press Skip for next cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
Wait the end of the Power Cleaner.
Afterwards the machine exits the cleaning
menu and it will be ready to dispense
drinks.
PLEASE WAIT
Skip
50
8► Open the machine door
GROUP CLEANING
OPEN FRONT PANEL AND
CLEAN COMPONENT
3► P
start f
Start key to confirm.
Shift key pressed for five
.
10
►
Close the machine door
16►
1
3►
Start
MILKER CLEANING
Start
17
►
18
►
t the endofthemilkercleaning
cycle the displaywillshow
Put the milkinfeedpipeintoaglassofcold
tart
MILKER CLEANING
MILKERCLEANING
Repeatusingonlywater,press
Start
11
►
12
►
. Wait theendofthegroupcleaning
1
4
►
15
►
Press
cleaning cycle
GROUPCLEA
MIXER CLEANING
PressStartforcleaning
POWERCLEANING
GROUPCLEANING
MILKERCLEANING
DISPLAYCLEANING
SUGGESTEDCLEANING
Start
NING
POWER CLEANING
GROUP CLEANING
Open the front door and insert the
detergent tablet into the brewing chamber.
Close the machine door.
cycle.
PLEASE WAIT
GROUP CLEANING
Press Start key to confirm the mixer
cleaning cycle (only for machine with
choco unit)
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
SUGGESTED CLEANING
Prepare a solution of water and detergent
(q.ty 200ml for standard version, 500ml if
milk pump present) by following the
instructions indicated in the product label.
Take the milk feeding tube out of the milk
box. Insert the milk feeding tube into a
container with detergent.
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
Press Start key to confirm
Insert cleaning solution
GROUP CLEANING
INSERT CLEANSER
Wait the end of the mixer cleaning
cycle.
frother).
4.42
Start key to confirm the milker
(only for machine with milk
PLEASE WAIT
MIXER CLEANING
2.02
Wait the end of the milker cleaning
cycle.
PLEASE WAIT
1.59
A
water.
Press S
cycle.
start for cleaning
key to confirm Miker rinsing
.
IN CASE THE COFFEE MACHINE IS EQUIPPEDWITHSTEAMBOILERBUTWITHOUTMILKFROTHERISNECESSARYTO
PERFORM THE STEAM BOILER CLEANING.
boiler cleaning is displayed onlyifthe“Steamboilercleaningfrequency”parameterhasbeenprogrammed.
AT THE END OF THE CLEANINGCYCLES PROCEDURESTHE DISPLAY WILLSHOW:
Start
18
►
DISPLAY CLEANING
1
6
►
17
►
A
cleaning
the display
Start
BOILER CLEANING
19
►
20
►
At thisstageyoucanusethedisplay
to see howtomanuallycleanthecoffee
dispenser,themilkfrother,themixer,the
hopper, thegroundsbinandthedriptray
SUGGESTEDCLEANING
Manualcleaningofmixer
Other recommendedcleaning
Manualcleaning:Milkfrother,coffee
SELECT DRINK
GROUNDS BIN FULL
Please note : the
15► Press Start key to confirm the milker
cleaning cycle
touch screen using a soft cloth and water.
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
BOILER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
During this time out you can clean the
PLEASE WAIT
0.15
18►
Wait the end of the steam boiler
partial draining (BOILER CLEANING).
Hot water will be drained into the drip tray.
At the end of the Display cleaning the
display shows.
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
PLEASE WAIT
0.20
t the end of the steam boiler
cycle , press Start key to confirm
cleaning
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
BOILER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
.
Ʌ
V
esc
WAIT AT LEAST 10 SECONDS , THE DISPLAYWILLSHOW:
a) Do not interrupt the cleaning cycle. If the cleaningcycleisinterruptedbyanytypeofoperationunrelatedtotheproced
the cleaningcyclewillautomaticallybeactivated.
b) Only in case that after the automatic cleaningprocessofthecoffeeoutletorthemilkfrotherarenotproperlydispensin
machine functioning is set back again,
manual cleaning; see the following steps.
FOR CLEANING OPER
CLEANING TABLETS
Remove and empty the grounds bin.
Reinsert the drip tray.
R
tray.
ure, when the
g, carry out a
MANUAL CLEANING: MILK FROTHER, COFFEE OUTLET
1 ► Open the machine remove the coffee
outlet from itsholder .
3 ► Disassemble the milk frother in all its
parts (first by turning and then by pulling as
shown in the picture) and wash it either by
hand or in a dishwasher. Make sure that all
the holes are free from milk residues and
also to use provided tools to clean the
holes. Check also that the O-rings are in
good condition
2 ► Remove the milk frother from the
coffee outlet and disconnect Silicone
tubes No. -3- and -4.
4 ► Disassemble the coffee outlet (1)
and wash it by hand or in a dishwasher.
Make sure that all the holes are free
from any coffee residues , and also to
use provided tools to clean the holes.
3
4
►
5
►
7
►
6
►
2
3
2
WE STRONGLY RECOMMEND CLEANING THE MIXERS ONCE A DAY
1► Open the machine door
Remove the Decanter
Insert the mixer 1 then turn the
flange clockwise 2 , then reinsert the
product outlet elbow 3.
MANUAL CLEANING OF MIXER
2► Remove the pipe from the mixer
Rinse the Mixer and the Decanter
in a sink
8► Reinsert the pipe from the mixer
► Remove the product outlet elbow
1, then turn the flange 2 anticlockwise,
then remove the mixer 3
Reinsert the Decanter
OTHER RECOMMENDED CLEANING
DRIP TRAY CLEANING GROUNDS BIN CLEANING
Once a day rinse the drip tray in a sink.
Once a day rinse the grounds bin in a
sink.
HOPPER CLEANING DISPENSER CLEANING
a) Once a week clean the hopper by
means of a cloth and approved food
detergent.
b) Turn the screw on the top of the
machine anticlockwise and then
remove the hopper.
a) Once a week clean the dispenser
by means of a cloth and approved
food detergent
b) Open the front door and remove
the product outlet .
c) Remove the canister
CHUTES CLEANING
a) Open the decaffeinated door and
remove the chute .
b) Once a week clean the
decaffeinated chute by means of a
brush and approved food detergent
GRINDERS ADJUSTMENT
a) Turn the screw on the top of
the machine anticlockwise and
then remove the hopper.
Please Note: Brew and throw two doses, the third one will be dispensed with the new grinder set
b) Move the adjustment to the
right to get coarse coffee powder,
to the left for finer.
c) Once a week clean the coffee chute by
means of a brush and approved food
detergent
c) Reinsert the hopper and lock it
by turning the screw clockwise.
MILK FROTHER ADJUSTMENT
Foam setting
The milk frother is equipped with a FOAM REGULATOR which sets the quantity of air needed to froth milk.
Open the machine door turn the ring nut clockwise for thicker foam (small bubbles), or turn it anticlockwise for more voluminous foam
(large bubbles) then lock it with the locknut. Pic.A.
Milk temperature setting
The milk frother is equipped with a MILK TEMPERATURE REGULATOR which reduces the quantity of sucked milk.
Turn the regulator clockwise to increase the milk temperature, or turn it anticlockwise to reduce it.
Pic. A
a) Lift the coffee outletscompletely
MACHINEFUNCTIONSME
micro switchdo
the display shows
rounds bin full; the number of coffeegroundsinthebinhasreachedtheprogrammedvalue
based dispensingselections
ress ( Info ) key, the display shows:
FULL
emove and empty thegroundsbin.
OFF
CLOSE FRONT PANEL
SELECT DRINK
EMPTY GROUNDS BIN
CLOSE THE GROUNDS BIN
1) Alarm for machine door position
Cause: the front door is open; the
Result: shutdown of the machine functions
Solution: press ( Info ) key,
Close the door and turn the machine ON.
2) Full grounds bin alarm
Cause: g
Result: shutdown of the coffeeSolution: p
GROUNDS BIN FULL GROUNDS BIN
After 10 seconds the display shows :
es not touch the door
:
GROUNDS BIN OPEN
OPEN DOOR
OPEN DOOR
GROUNDS BIN FULL
WAIT 10 SEC.
GROUNDS BIN FULL
b) R
SSAGES
Press ( Info ) key, the display shows:
SELECT DRINK
FILL THE HOPPER
SELECT DRINK
INSERT DECA COFFEE
CLOSE THE GROUNDS BIN
Reinsert the grounds bin into its housing.
3) Message of missing coffee
Cause: there is no coffee into the hopper and therefore into the brewing chamber
Result: the machine interrupts the coffee-based dispensing selections
Solution : press ( Info ) key, the display shows :
to reset the alarm put coffee into the hopper and press again the dose required.
4) Message of missing decaffeinated
Cause: Missing coffee in the decaffeinated door and in the brewing chamber
Result: The machine interrupts the decaffeinated dispensing selections
Solution : press ( Info ) key, the display shows :
To reset the alarm put decaffeinated into the decaf door and press again the dose required.
GROUNDS BIN OPEN
MISSING COFFEE
MISSING COFFEE
POWNDER 7/8 gr. min.
MISSING DECAF.
MISSING DECAF.
5) Message of drip tray not in position.
SELECT DRINK
INSERT DRIP TRAY
SELECT DRINK
EMPTY THE DRIP TRAY
The display will show the following message:
Cause: the drip tray is not in position. The micro switch contact is open.
Result: The message is displayed without disabled the dispensing keys.
Solution : press ( Info ) key, the display shows :
reinsert the drip tray.
DRIP TRAY OUT
DRIP TRAY OUT
6) Message of drip tray full. ( ONLY FOR MACHINES WITHOUT DIRECT WATER DISCHARGE )
The display will show the following message:
Cause: waste bin is full. The quantity of water inside the drip tray touches the level probe .
Result: shutdown of the dispensing keys.
Solution : press ( Info ) key, the display shows :
remove the drip tray and empty it.
PLEASE NOTE: FOR ALL OTHER MESSAGES PLEASE REFER TO YOUR SERVICE CENTER.
DRIP TRAY FULL
DRIP TRAY FULL
WITHSMARTCARD
To enter the programming environments, placeoneofthefollowingsmartcardsabovetheproperreaderwiththeledlightONw