Carewell Electric Technology FAN65T User Manual

Remote controller

GENERAL INFORMATION

This remote controller is designed to separately control your ceiling fan speed and light brightness. There are seven buttons (1, 2, 3, OFF) to control fan speed and off. The light dimmer button will control the light brightness dimmer and off. The blue indicator on the transmitter will light when one of the nine buttons is pressed.

INSTRUCTION OF INSTALLATION AND OPERATION

1.SETTING THE CODES

Setting the codes on the transmitter: a. Remove battery cover. b. Factory setting is all on the “ON”position.If you want to change the codes setting,please use a small screwdriver or a ball point pen to slide firmly to your choice of”ON”or”OFF”position.(Figure 1).

The Learn Key must be pressed within 30 seconds, after pressing the Power button. If not, please press the Power button to restart. Keep pressing the “LEARN”key in excess of 3 seconds it becomes a LEARN status.The receiver can remember the last codes status.Then the light on the Fan will flash two times.

2.INSTALLING RECEIVER IN CEILING FAN

ACN

A. Safety precautions: WAR NI NG : HI GH V OLTAGE! Disconnect power by removing fuse or switching off circuit breaker. Do not use with solid state fans. Electrical wire must meet all local and national electrical code requirements. Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor watts: 40W, Maximum down light watts: 60W led. Otherwise power can cause serious injury or death. B. Installing receiver in fan: a. Remove power from the circuit. b. Remove ceiling fan canopy from the mounting bracket. c. Disconnect existing wiring between ceiling fan and Supply in electrical junction box. d. Make connections as follows, using the wire nuts supplied:

If other fans or supply wires are different color, have this unit installed by qualified licensed electrician. e. Push all connected wires up into junction box. f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket. g. Reinstall the canopy on the mounting bracket. h. Restore power.

LEAR N

SWIT CH

LEARN

SWITCH

LIGHT

DIM

LIGH T

DIM

INP UT

OUT PUT

CAUTION: Ceiling An gl e Sh al l No t Ex ce ed 3 0 De gr ee s, For Mounting Controller, Model AC8

CONN ECT TO

Green fan wire ....Bare supply wire

Black receiver wire(AC IN L) .... Black supply wire

White receiver wire(AC IN N) ....White supply wire

Black receiver wire(FOR MOTOR) .... Red fan wire

White receiver wire(FOR COM) ....White light wire

Blue receiver wire(FOR LIGHT) ....Blue light wire

ACL

COM

LIG HT

RECEIV ER

FAN

ANT

FROM POWE R SOURC E AC 110~1 20 VOLT 60Hz

3.5AMPS .

WIRE N UT

Use wire co nn ecting nu ts supplie d wi th the remo te

WHI TE

INP UT

OUT PUT

Use wire connecting nuts supplied with the fan

(FIG.3)

BLA CK

CAN OPY

ECEI

VER

ANT

ANTE NNA PUT AT OUT SIDE OF CAN OPY BOX C AN GET MORE O PERATI ON DISTA NCE

RECEI VER

(FIG.4)

CANOPY

PJE S1412

3. OPERATING TRANSMITTER: A. Install 3 volt battery(not included). (To prevent damage to transmitter, remove the battery if not used for a long time).

B. Store the transmitter away from excessive heat or humidity. C. This remote control unit is equipped with rolling code combinations. In order to prevent possible interference from or to other remote units such as garage door openers, car alarm or security system. If you find that your fan and light kit go on and off without using your remote control, simply change the code combination in your transmitter and receiver. D. Operating the buttons on the panel of the transmitter. 1-3 key -for fan speed control. OFF key-for fan off. LIGHT key-for down light brightness . The light function is controlled by pressing the LIGHT ke y do wn t o in cr ea se o r de cr ea se l ig ht . Tap k ey q ui ck ly t o tu rn l ig ht o ff or on. Keep pressing the button in excess of 0.7 second and it becomes a dimmer, the light varies cyclically in 0.8 second. The receiver can remember the last status of the light brightness when the light was switched, so that it can resume to adjust the light brightness.

FCC Statement:

1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may casue harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--- Reorient or relocate the receiving antenna.

--- Increase the separation between the equipment and receiver.

--- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--- Consult the dealer or an experienced radio/ TV technician for help.

Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device."

2.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Avis d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio par un appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio d’industrie Canada.

YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.

OPERATIO N DI STANCE 20 FE ET

Optional Wa ll M ou nt in g fo r Tra ns mi tt er H ol de r Place in accessible area of your home, and screw the transmitter holder into wall using the two screws provided, slide hand unit into holder.

4. TROUBLE SHOOTING GUIDE

1. Fails to operate a. Power to receiver ? b. Receiver wired correctly ? c. Fan manual speed control in highest position ? d. Light kit switch turned on ? e. Good battery in the transmitter ? f. Code set at exact same positions in both transmitter ?

2. Won't o pe ra te a t di st an ce If transmitter operates fan/light kit when up close, but not at 20 feet away. Try placing the brown antenna wire higher, up through ceiling/outside the junction box.

NOTICE !

Your ceiling fan and light kit assembly must meet the following requirements:

1. Do not use with solid state fans.

2. Electrical rating: 120v 60Hz 3.5A MAX. Motor watts: 40W MAX. Light watts: 60W (led)

SIZE : AAA 1.5V

TRANSMITTER

MODEL: FAN-65T

WARNING

TO RE DU CE THE RISK OF SHOCK, THIS FAN MUST BE I NS TALLED WITH A WALL CONTROL/SWITCH. CAUTION: High Voltage-Disconnect power supply before servicing. DANGER-To Reduce the RISK of Electric Shock-Do not connect to a circuit operating at more than 150 volts to ground.

PJE S1412