Carewell Electric Technology AC83T User Manual

Remote controller

GENERAL INFORMATION

This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off.
The light dimmer button will control the light brightness dimmer and off.
The red indicator on the transmitter will light when one of the five buttons is pressed.

INSTRUCTION OF INSTALLATION AND OPERATION

1.SETTING THE CODES

This unit has 16 diff er en t co de c om bi na ti on s. To set the codes, perform the following steps:
A. Setting the codes on the transmitter:
a. Remove battery cover. Press firmly on the arrow and slide battery cover off.
b. Slide code switches to your choice of up or down position. (Factory setting is all up. Do not use this position. Use a
Small screwdriver or ball point pen to slide firmly up or down (Figure 1)).
B. Setting the codes on the receiver:

The Learn Key must be pressed within 30 seconds, after pressing the Power button.

If not, please press the Power button to restart.

Keep pressing the button learn key in excess of 3 second it becomes a LEARN status.

The receiver can remember the last codes status .The light flash two times.

2.INSTALLING RECEIVER IN CEILING FAN

A. Safety precautions:
WAR NI NG : HI GH V OLTAGE! Disconnect power by
removing fuse or switching off circuit breaker.
Do not use with other solid state fans.
Electrical wire must meet all local and national
electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum
fan motor amps: 1.0, Maximum down light watts: 60
LED.
Maximum up light watts: 100 incandescent and ballast.
Otherwise power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting
bracket.
c. Disconnect existing wiring between ceiling fan and
Supply in electrical junction box.
d. Make connections as follows, using the wire nuts

FROM POWER SOURCE
AC 110~120 VOLT 60Hz

3.5AMPS.

Use wire connecting nuts supplied with the fan

(FIG.3)

ACN

A
C
L

1

ON

TRANSMITTER

2

3

4

CODE

SWITCHES

(FIG.1)

O

N

INPUT

OUTPUT

ACN

COM

ACL

FAN

RECEIVER

LIGHT

ANT

Model FA N52R- M60

CONN ECT TO

Green fan wire ....Bare supply wire

Black receiver wire(AC IN L) .... Black supply wire

White receiver wire(AC IN N) ....White supply wire

White receiver wire(TO MOTO R N) . .. .W hi te f an w ir e

Black receiver wire(TO MOTO R L) . .. .B la ck f an w ir e

Blue receiver wire(DOWN LIGHT) ....Blue light wire

CODE

SWITCHES

(FIG.2)

WIRE NUT

Use wire connecting nuts
supplied with the remote
controller.

WHITE

WHITE

WHITE

INPUT

OUTPUT

RED

ANT

(FIG.2)

CANOPY

R

ECE

IV

E

BLUE

B

L

AC

K

B

L

ACK

BLUE

CANOPY

R

LIG HT MUST KE EP AT THE T URN ON

FAN MU ST KEEP AT THE HI GH SPEE D

PJE S1002

If other fans or supply wires are different colour, have this unit installed by qualified licensed electrician.
e. Push all connected wires up into junction box.
f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power.

3. OPERATING TRANSMITTER:
A. Install 12 volt battery. (To pr ev en t da ma ge t o tr an sm it te r, re mo ve t he b at te ry i f no t us e fo r a lo ng t im e) .

B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. To pre ve nt p os si bl e in te rf er en ce f ro m or t o ot he r
remote units such as garage door openers, car alarm or security system. If you find that your fan and light kit go on
And off without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
HI key -for fan high speed.
MED key-for fan medium speed.
LOW key-for fan low speed.
OFF key-for fan speed off.
FAN REV key-for fan reverse .

The light function is controlled by pressing the LIGHT ke y do wn t o in cr ea se o r de cr ea se l ig ht .
Tap k ey q ui ck ly t o tu rn l ig ht o ff or on.
Keep pressing the button in excess of 0.7 second it becomes a dimmer, the light varies cyclically in 0.8 second.
The receiver can remember the last status of the light brightness when the light was switched, so that it can
resume to adjust the light brightness.

YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.

OPERATION DISTANC E 20 F EE T

23A 12V

FCC ID: L 3HFAN3 5T2

Optional Wa ll M ou nt in g fo r Tra ns mi tt er H ol de r
Place in accessible area of your home, and screw the
transmitter holder into wall using the two screws
provided, slide hand unit into holder.

4. TROUBLE SHOOTING GUIDE

1. Fails to operate
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
f. Code set at exact same positions in both transmitter and receiver ?

2. Won t operate at distance

'

If transmitter operates fan/light kit when the up close, but not at 20 feet away.
Try placing the brown antenna wire higher, up through ceiling/outside the junction box.

TRANSMITTER

MODEL:
FAN-35T2

NOTICE !

Your ceiling fan and light kit assembly must meet the following requirements:

1. Do not use with other solid state fans.

2. Electrical rating: 120v 60Hz 3.5A
MAX. Motor amps: 1.0
MAX. Down Light watts: 60-(LED)

WARNING

TO RE DU CE THE RISK OF SHOCK, THIS FAN MUST BE I NS TALLED WITH A WALL CONTROL/SWITCH.
NOTE: THE MANUFACTURER IS NOT RE SP ON SI BL E FO R ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATI ON S TO TH IS E QU IP ME NT. SU CH M OD IF IC ATIONS COULD VOID THE
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

PJE S1002