Cardo Systems ER11 User Manual

™

TeamSet

PRO

™

communic ation in mot ion

Gebrauchsanleitung

Guide d’Utilisation

Guida di Avvio
Guia de Usario

™

User Guide

QG TSpro 002 - QG0xx.indd 1 12/31/09 5:45 PM

© Cardo Systems, Inc.

The Bluetoot h® word mark and logos are owned by the Bluetooth SIG, Inc. Any use of such marks by Cardo Systems, Inc. is under license.

Other trademarks and trade names are those of their respective owners.

®

2

scala rider

QG TSpro 002 - QG0xx.indd 2 12/31/09 5:45 PM

TeamSe t

™

PRO

INTRODUCTION

scala

pro

CONTENTS OF RETAIL BOX

English

Congratulations and thank you for choosing the scala rider

pro

Bluetooth® Headset package for bikers.

TeamSet

This User Guide will help you operate the headset, but you should rst
familiarize yourself with the Bluetooth functionality of your cellular phone
and/or GPS device before using the scala rider

This retail box contains two scala rider

TeamSet

TeamSet

pro

headsets that

pro

.

already factory paired (see details below).

The scala rider

TeamSet

pro

headset can also serve as a stand-alone

unit for the following connectivity modes:

• As a Bluetoot h headset for mobile phone communication**

• As a speaker that transmits GPS Navigation instructions from a
compatible GPS device***

• As stereo speakers that transmit music from your MP3 player

NOTE: Each

TeamSet

pro

headset can establish an audio connection
with one Bluetooth device at a time. Read the section “Using the Headset”
on how to switch the audio connection between the paired devices.

__ __ ____ _____ ____ ___

* Full duplex calls allow you to speak and hear the other party speak simultaneously

** Mobile phones that do not support the Bluetooth Ha ndsfree prole may prevent you

from using the Redial and Call Reject features. The
handsfree proles at up to 10 m / 30 ft. distance from the mobile phone

*** Requires Bluetooth compatibility on the part of the GPS device

TeamSet

pro

supports headset and

Two Headsets

CTRL – Control Button

• Power On, Power O

• Answer/End Call

Two Helmet Clamps

Right Speaker
(long cord)

Microphone

NOTE: The scala
rider

TeamSet

is also available in a cord-mounted
microphone version to better t certain
full-faced helmets with tight chin sections.

pro

Tab

Sliding Plate

MC – Multi-Connection

• Initiate/Terminate
Intercom call

®

scala rider

Volume

Up

Charging
Jack

Volume
Down

Left Speaker
(short cord)

Back
Plate

MP3 Jack

TeamSe t

™

PRO

3

QG TSpro 002 - QG0xx.indd 3 12/31/09 5:46 PM

1 Dual Wall Charger

2 Allen Wrenches

2 sets of Velcro Pads

2 MP3 Cables

2 MP3 Cable Holders

2 Glue Plates

2 Pre-moistened Towelettes

2 Carry-Pouches

4 Microphone Sponges

Flat sponge for full-face helmets and round sponge for other helmet types

User Guide, including Warranty and Registration form

IMPORTANT:

Your headsets are water-resistant, designed for use under moderate
rain or snow conditions. However, the headsets are not waterproof
and should not be used under severe weather conditions.

The cover tongue protecting the Charging Jack should be kept tightly
closed at all times to prevent moisture from entering the device.

NOTE: WHILE MOST INSTRUCTIONS IN THIS MANUAL REFER TO THE HEADSET IN THE

SINGULAR, THEY APPLY TO BOTH UNITS UNLE SS INDICATED OTHERWISE.

BEFORE USING (CHARGING THE
HEADSET)

Make sure that the headset is fully charged for at least four hours
before initial use.

1. Connect the wall charger to the headset’s Charging Jack (located
between the two Volume Buttons).

2. While charging, the Red Light turns on (it may take up to 15
seconds until the Red Light turns on). When charging is complete,
the Red Light will turn o.

4

scala rider

® Q2™

MultiSe t

SET UP AND CONFIGURATION

GPS

Mobile

phone

Driver-to-

Passenger

Full-dup lex

Intercom

Connectio n

SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING

Pairing is a one time process that is required for mutual recognition
between a headset and other Bluetooth devices. Once the two head­sets are paired, they will remain paired and automatically recognize
each other whenever they are within range. The two headsets in
your retail box are already factory paired and relate to each other as
the Buddy connection. If for any reason, you have to pair them again,
proceed as follows:

1. If either headset is turned OFF, turn it ON by pressing and holding
the CTRL Button until the Blue Light ashes three times.

2. Make sure that both headsets are now ashing slowly in Blue.

MP3

player

QG TSpro 002 - QG0xx.indd 4 12/31/09 5:46 PM