Cardinal Detecto 6127 Series, Detecto 6337, Detecto 6129 Series, Detecto 6339 Operating Instructions Manual



(

DIGITAL PHYSICIAN

Waist-High Scale

Model 6127 Series, 6129 Series

Eye-Level Scale

Models 6337 and 6339

Operating Instructions

CARDINAL SCALE MFG. CO.
8525-M310-O1 Rev E
06/15

www.detectoscale.com

PO BOX 151

417) 673-4631 FAX [phone]

PH

WEBB CITY, MO 64870

and

Printed in USA

Technical Support: Ph: 866-254-8261  [e-mail]

8525-M310-O1 Rev E  612X Series and 633X Series

1

2

8525-M310-O1 Rev E  612X Series and 633X Series

FCC COMPLIANCE STATEMENT

This equipment generates uses and can radiate radio frequency and if not installed and used
in accordance with the instruction manual, may cause interference to radio communications. It
has been tested and found to comply with the limits for a Class A computing device pursuant
to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection
against such interference when operated in a commercial environment. Operation of this
equipment in a residential area may cause interference in which case the user will be
responsible to take whatever measures necessary to correct the interference.

You may find the booklet “How to Identify and Resolve Radio TV Interference Problems”
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Request stock No. 001-000-00315-4.

PROPER DISPOSAL

When this device reaches the end of its useful life, it must be properly disposed of. It must not
be disposed of as unsorted municipal waste. Within the European Union, this device should
be returned to the distributor from where it was purchased for proper disposal. This is in
accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.

It is everyone’s responsibility to help maintain the environment and to reduce
the effects of hazardous substances contained in electrical and electronic
equipment on human health. Please do your part by making certain that this
device is properly disposed of. The symbol shown to the right indicates that
this device must not be disposed of in unsorted municipal waste programs.

COPYRIGHT

All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to
the use of the information contained herein.

DISCLAIMER

While every precaution has been taken in the preparation of this manual, the Seller assumes
no responsibility for errors or omissions. Neither is any liability assumed for damages resulting
from use of the information contained herein. All instructions and diagrams have been
checked for accuracy and ease of application; however, success and safety in working with
tools depend to a great extent upon the individual accuracy, skill and caution. For this reason
the Seller is not able to guarantee the result of any procedure contained herein. Nor can they
assume responsibility for any damage to property or injury to persons occasioned from the
procedures. Persons engaging the procedures do so entirely at their own risk.

Serial Number_______________________
Date of Purchase ____________________
Purchased Form_____________________

___________________________________
___________________________________

RETAIN THIS INFORMATION FOR FUTURE USE

8525-M310-O1 Rev E  612X Series and 633X Series

PRECAUTIONS

Before using this instrument, read this
manual and pay special attention to all
"WARNING" symbols:

IMPORTANT ELECTRICAL

WARNING

3

I

This page intentionally left blank.

4

II

8525-M310-O1 Rev E  612X Series and 633X Series

INTRODUCTION

Thank you for your purchase of our Detecto Digital Physician Waist-High or Detecto Digital
Physician Eye-Level scale. It has been manufactured with quality and reliability at our factory
in Webb City, MO USA. Your scale has been tested before leaving our factory to insure
accuracy and dependability for years to come.

This manual will guide you through assembly, installation, and operation of your scale. Please
read it thoroughly before attempting to use your scale and keep it handy for future reference.

SPECIFICATIONS

Capacity: 550 lb x .2 lb

(250 kg x .1 kg), selectable

Platform Size: 10 5/8” x 14 1/2”

(270 mm x 368 mm)

Dimensions: 10 7/8” W x 20 7/8” D x 37 7/8” H

(276 mm x 530 mm x 962 mm)
Shipping Weight: 34 lb (15.4 kg) 36 lb (16.3 kg)
Scale Height: 37 1/2 ” (953 mm) 57 1/8” (1451 mm)
Height Rod Measures: 6129, 6129KG, 6339 - 30” to 78” (76 cm to 200 cm) x inch/cm

6129KGM - 30” to 78” (76 cm to 200 cm) by 1/4”/1mm
Display: Six digit, Seven segment, 0.7 inch (17.8 mm) high LCD
Power Requirements: 6 “AA” size Alkaline, Ni-Cad or NiMH batteries (not included) OR an

optional 100 to 240 VAC 50/60Hz 12 VDC 1A wall plug-in UL/CSA

listed AC power adapter (Cardinal part number 6800-1045).
Keyboard: Membrane type with 5 keys and 4 directional arrows

Waist-High Eye-Level

550 lb x .2 lb
(250 kg x .1 kg), selectable

10 5/8” x 14 1/2”
(270 mm x 368 mm)

10 7/8” W x 20 7/8” D x 57 1/2” H
(276 mm x 530 mm x 1461 mm)

8525-M310-O1 Rev E  612X Series and 633X Series

1

UNPACKING INSTRUCTIONS

 Remove scale from carton by lifting up with equal force from column and platform base.
 Check for any damage incurred in shipping. If scale has been damaged, place a claim with

the carrier. Use the original carton and shipping material to return the scale.

 Remove all plastic wrapping, foam fillers and cardboard material from the scale.
 Remove and unpack the power supply and cord, if the scale was ordered with this option.
 Carton contents:

1) Column

2) Indicator

3) Platform base

4) Screws and lock washers

5) Height measuring rod - optional

NOTE! If column bracket is bent,
straighten before assembling.

ASSEMBLY INSTRUCTIONS

Refer to Figures No. 1, 2, 3, and 4, then follow the instructions for scale assembly.

1. Carefully remove load cell and draft rod assembly from column.

IMPORTANT! Handle load cell assembly with care! Do not drop, bend or twist.

2. Slip column over column bracket on platform base. Screw column to column brackets
(two 1/4 truss head screws in front of column and four in the back). See Figure No. 1.

3. Referring to Figure No. 2, remove both #10-32 Truss Head Screws and lock washers
securing the indicator bracket to the column.

4. Lower load cell and draft rod assembly into column. Draft Rod must pass through
opening in column bracket. Referring to Figure No 1, make sure open end of lower draft
rod hook is facing forward toward platform.

5. Next, referring to Figure No. 3, fasten top hook bolt of load cell assembly (C) to column.
Make sure the load cell assembly does not touch the sides of column.

6. Slide grommet away from load cell assembly and slide into slot on column. NOTE! The
slot should be on back (wide side) of column.

7. Pull excess load cell cable in column leaving enough slack in cable so as not to have
any side pull on load cell.

8. Place digital indicator bracket on column and attach with 2 (#10-32) truss head screws
and lock washers removed in step 3. See Figure No. 2.

9. Using a desk or table, lay down scale with column horizontal to floor. Raise draft rod
keeping out of lever's way. Push lever. When lever is in position, hook draft rod around
pivot. See Figure No. 4.

10. Attach indicator to indicator bracket on column, then connect load cell cable to back of
indicator. Refer to the 750 Weight Indicator Owner’s Manual (8555-M483-O1) for
additional information.

11. Scale is now ready for operation.

2

8525-M310-O1 Rev E  612X Series and 633X Series

ASSEMBLY INSTRUCTIONS, CONT.

Grommet

Load
Cell

Cable

Figure No. 1

Figure No. 3

Column

C

Draft
Rod

#10-32 Truss
Head Screw

Opening

Column
Bracket

Raise

Draft

Rod

Push

Lever

Figure No. 4

Indicator
Bracket

Lock
Washer

Figure No. 2

8525-M310-O1 Rev E  612X Series and 633X Series

3

OPERATION

ALWAYS assist the patient in stepping on and off the scale platform to
ensure they do not fall. NEVER leave a patient unattended while they are on
the scale platform. Failure to maintain control of the patient at all times can
result in serious injury to you and/or the patient.

To Weigh

1. Set scale on any hard, level, flat surface or low-cut carpet.

2. Press ON/OFF key to turn on indicator.

3. Press ZERO key to zero weight display. The ZERO and lb or kg annunciator will turn on
to show that scale is ready for use.

4. Place patient on scale and read weight display.

5. Remove patient from scale.

Zero Weight Display

1. If the indicator is not showing zero weight on the display, press ZERO key.

2. Weight display will return to zero. ZERO, STABLE  and lb or kg annunciators will
turn on to show a stable, center-of-zero weight condition.

Metric Conversion

Press UNITS key to toggle between pounds and kilograms. Note that lb or kg
annunciator will turn on to show which weighing unit is active.

4

8525-M310-O1 Rev E  612X Series and 633X Series

OPERATION, CONT.

To Weigh and Calculate BMI

1. Press ON/OFF key to turn on indicator.

2. Press ZERO key to zero weight display. The ZERO and lb or kg annunciator will turn on

to show that scale is ready for use.

3. Place patient on scale and read weight display.

4. Press BMI / ENTER key.

5. If pounds is the active weighing unit, display will change to show 5

FEET

6 blinking. (The blinking character is the position to be changed).

a. Press  or  keys until desired height in inches is displayed and then press  or

 key to move the blinking character to FEET.
b. Press  or  keys until desired height in feet is displayed.
c. Proceed to Step 7.

6. If kilograms is the active weighing unit, display will change to show 170
170 blinking. (The blinking character is the position to be changed).

a. Press  or  keys until the desired number is displayed.
b. Press  or  key to move to next character to change.
c. Repeat steps A and B until the desired height in centimeters is displayed.
d. Proceed to Step 7.

7. Press BMI / ENTER key.

8. Read BMI on display.

9. Remove patient from scale.

10. Press BMI / ENTER key to return to weighing operation.

, 6

INCHES

.with the 0 of

cm

with the

8525-M310-O1 Rev E  612X Series and 633X Series

5

HEIGHT ROD INSTRUCTIONS

(

)

(Waist-High Models)

Height Rod Hole Location

Please check the Height Rod hole
locations before installing the Height Rod.

 Some models may require holes to

be drilled.

 Please follow the measurements for

drilling holes if necessary.

 After holes have been drilled, please

follow installation instructions.

IMPORTANT!

Measure from bottom of column,
not floor or scale base.

2in (51mm)

47/64”

29

(75.5 cm)

9/64”

(3.5mm)
diameter holes,
1” (25.4mm) from
center of column
to center of hole

Height Rod Installation

1. Remove the height rod, height rod
brackets and hardware pack from
the cardboard insert.

2. Attach the height rod brackets to the
height rod using the four screws,
lock washers and nuts enclosed in
the hardware pack. Tighten all four
screws.

5

13.3 cm

Height Rod

15/64”

Height Rod
Bracket

6

8525-M310-O1 Rev E  612X Series and 633X Series

HEIGHT ROD INSTRUCTIONS, CONT.

(Waist-High Models)

3. Place the large end of the slotted
holes in the height rod brackets over
the four hex head screws on the back
of the column.

4. Pull down to set the screws in the
small end of the slotted hole and
secure the bracket to the column.

5. Use the included wrench to tighten the
hex head screws. Do not over-tighten
the screws.

Height Rod
Bracket

Scale

Column

8525-M310-O1 Rev E  612X Series and 633X Series

7

HEIGHT ROD INSTRUCTIONS, CONT.

(Waist-High Models)

Operation

1. Before patient steps onto scale platform,
spoon should be rotated to horizontal
position, and raised well above patient's
apparent height.

A

B

2. Patient may now step onto scale platform.
Spoon should be held horizontal and above
patient's head.

E

3. Carefully lower spoon, keeping it
horizontal, until it rests gently on top of
patient's head. If patient is shorter than 3'
4" (101.5 cm), push latch to right while
simultaneously pushing down on spoon,
until the spoon rests horizontally on top of

Height Rod in
“rest” position

patient's head.

4. Read height of patient as follows:

A = Latch
B = Spoon

 If back of spoon points to outer height

rod, then it points to correct height.

 If back of spoon points to inner height

rod, then correct height is read at top of

C = Inner Height Rod
D = Outer Height Rod
E = Measurement

“Read” Line

outer height rod (see "Read" arrow on
outer height rod).

5. While holding spoon horizontally, raise spoon above patient's head. Patient may now
step off scale platform. Hold spoon horizontal until patient is clear of height rod.

6. Rotate spoon back to vertical position and adjust height rod back to rest position (i.e.
spoon should be locked in place within inner height rod and inner rod should be at its
lowest position).

C

D

8

8525-M310-O1 Rev E  612X Series and 633X Series

HEIGHT ROD INSTRUCTIONS, CONT.

(Eye-Level Models)

Height Rod Installation

1. Remove cardboard insert from height rod.

2. If not already installed, insert the two hex head screws from the hardware pack into
holes in front of column and tighten them with included wrench until hex heads are 1/8"
from column.

3. Place both height rod brackets over two pre-installed hex head screws and pull down.

4. Use included wrench to tighten both hex head screws. Do not overtighten screws.

8525-M310-O1 Rev E  612X Series and 633X Series

9

HEIGHT ROD INSTRUCTIONS, CONT.

(Eye-Level Models)

1. Before the person steps onto the scale platform, the spoon should be rotated to the
horizontal position, and raised well above the person’s apparent height.

2. The person may now step onto the scale platform. The spoon should be held horizontal
and above the person’s head.

3. Carefully lower the spoon, while keeping it horizontal, until it rests gently upon the top of
the person’s head. If the person is shorter than 101.5 cm/3' 4", then push the latch to
the right, while simultaneously pushing down on the spoon, until the spoon rests
horizontally upon the top of the person’s head.

4. Read the height of the person as follows:

If back of spoon points to outer height rod, then it points to correct height.
If back of spoon points to inner height rod, then correct height is read at the top of

outer height rod (see “READ” arrow on outer height rod).

5. While holding the spoon horizontal, raise the spoon above the person’s head. The
person may now step off of the scale platform. Hold the spoon horizontal until the
person is clear of the height rod.

6. Rotate the spoon back to the vertical position and adjust the height rod back to the rest
position (i.e. the spoon should be locked in place within the inner height rod and the
inner rod should be at its lowest position).

CAUTION: Do not raise or lower Height Rod by the spoon tip!

10

8525-M310-O1 Rev E  612X Series and 633X Series

ERROR AND STATUS DISPLAYS

Display Meaning

-Err-

-OF-

-trL-

-UnS-

CALib

AdErr
ErrAL

General error, invalid keypad entry was attempted.
Attempting to display a negative number greater than –9,999 or a

positive number greater than 99,999.
Indicates an attempt to zero a weight outside scale zero range.
Motion is present when indicator is attempting to perform one of the

following operations: Power Up Zero or Zero Weight Display.
Indicates calibration is necessary.

Consult your scale service representative.

ErrAH

OCAP

OFF

Scale weight exceeds scale capacity.
Displayed to indicate indicator is turning off.

CARE AND CLEANING OF SCALE

 DO NOT subject platform to sudden shocks.
 DO NOT submerge indicator in water, pour or spray water directly on indicator.
 DO NOT use abrasive cleaners on this scale.
 DO NOT use acetone or other volatile solvents for cleaning.
 DO clean scale and indicator using a damp soft cloth and mild detergent.
 DO avoid areas where scale might be exposed to moisture.

8525-M310-O1 Rev E  612X Series and 633X Series

11

PARTS IDENTIFICATION

FINAL ASSEMBLY

ITEM QTY PART NUMBER DESCRIPTION

1 1 3P1201X-1 BASE ASSEMBLY
2 1 430XG3R800 COLUMN ASSEMBLY FOR 6127(KG), 6129(KG)

1 0044-C180-1A COLUMN ASSEMBLY FOR 6337, 6339
3 1 709GR1206 LOAD CELL ASSY
4 1 0033-B254-08 DRAFT ROD FOR 6127(KG), 6129(KG)

1 0033-B256-08 DRAFT ROD FOR 6337, 6339
5 1 3P8068 PLATFORM COVER
6 4 63K1038 BASE LEG
7 1 6650-0087 LABEL, MADE IN USA
8 1 0033-B438-0A MOUNTING BRKT
9 1 391RV204 NUT ELASTIC STOP 1/4-20 Z/P

10 1 6021-1454 SCW HEX HEAD 1/4 -20 X 3/4
11 1 6024-0004 WASHER FLAT 1/4
12 1 0033-B104-0A TOP PLATE ASSY.
13 1 593R986 SERIAL TAG
14 2 6024-0049 WASHER LOCK EXT #10
15 6 6024-0047 WASHER LOCK EXT 1/4
16 6 6021-1423 SCW TRUSS HEAD 1/4-20 X 1/2
17 2 6021-1045 SCW HEX HEAD #10-32 X 1/2 Z/P
18 1 750 DIG. WT. INDICATOR
19* 1 0033-D203-0A HEIGHT ROD ASSEMBLY, INCH/CM FOR 6129(KG)
20* 1 0033-D475-0A HEIGHT ROD ASSEMBLY, 1/4”/1mm FOR 6129KGM
21* 1 0033-D063-1A HEIGHT ROD ASSEMBLY, INCH/CM FOR 6339
22* 1 6800-1045 OPTIONAL AC ADAPTER 100-240VAC/12VDC @ 1A

* NOT SHOWN

12

8525-M310-O1 Rev E  612X Series and 633X Series

PARTS IDENTIFICATION, CONT.

BASE ASSEMBLY

ITEM QTY PART NUMBER DESCRIPTION

1 1 3P2011X PLATFORM WELDMENT
2 4 3P2087 PLATFORM LOAD BEARING
3 1 3P1001X BASE WELDMENT
4 2 3P60 CHECK PLATE
5 2 6021-0985 HEX WASHER HD SCW #10 X 1/2
6 4 63K1038 BASE LEG
7 1 2U58 UNION CENTER HANGER
8 1 3P8003X SHORT LEVER ASSEMBLY

9 4 3P8059 UNION HANGER
10 1 3P122 BUMPER
11 1 3P8002X LONG LEVER ASSEMBLY
15 6 6024-0047 WASHER LOCK EXT 1/4
16 6 6021-1423 SCW TRUSS HEAD 1/4-20 X 1/2

8525-M310-O1 Rev E  612X Series and 633X Series

13

STATEMENT OF LIMITED WARRANTY

Detecto Scale warrants its equipment to be free from defects in
material and workmanship as follows: Detecto warrants to the
original purchaser only that it will repair or replace any part of
equipment which is defective in material or workmanship for a
period of two (2) years from date of shipment. Detecto shall be
the sole judge of what constitutes a defect.

During the first ninety (90) days Detecto may choose to replace
the product at no charge to the buyer upon inspection of the
returned item.

After the first ninety (90) days, upon inspection of the returned
item, Detecto will repair or replace it with a remanufactured
product. The customer is responsible for paying for t he freight
both ways.

This warranty does not apply to peripheral equipment not
manufactured by Detecto; this equipment will be covered by
certain manufacturer’s warranty only.

This warranty does not include replacement of expendable or
consumable parts. This does not apply to any item which has
deteriorated or damaged due to wear, accident, misuse, abuse,
improper line voltage, overloading, theft, lightning, fire, water or
acts of God, or due to extended storage or exposure while in
purchaser’s possession. This warranty does not apply to
maintenance service. Purchased parts will have a ninety (90) day
repair or replacement warranty only.

Detecto may require the suspect product to be ret urned to the
factory; item(s) must be properly packed and shipping ch arges
prepaid. A return authorization number must be obtained for all
returns and marked on the outside of all returned packages.
Detecto accepts no responsibility for loss or dam age in transit.

14

8525-M310-O1 Rev E  612X Series and 633X Series

STATEMENT OF LIMITED WARRANTY

Conditions Which Void Limited Warranty

This warranty shall not apply to equipment which:
A.) Has been tampered with, defaced, mishandled or has had

repairs and modifications not authorized by Detecto.
B.) Has had serial number altered, defaced, or removed.
C.) Has not been grounded according to Detecto’s recommended

procedure.

Freight Carrier Damage

Claims for equipment damaged in transit must be referred to the
freight carrier in accordance with freight carrier regulations.

This warranty sets forth the extent of our liability for breach of any
warranty or deficiency in connection with the sale or use of the
product. Detecto will not be liable for consequential damages of
any nature, including but not limited to, loss of profit, delays or
expenses, whether based on tort or contract. Detecto reserves
the right to incorporate improvements in material and design
without notice and is not obligated to incorporate improvements in
equipment previously manufactured.

The foregoing is in lieu of all other warranties, express or implied
including any warranty that extends beyond the descripti on of the
product including any warranty of merchantability or fitness for a
particular purpose. This warranty covers only those Detecto
products installed in the forty-eight (48) contiguous continental
United States.

Ph. [phone]

E-mail: [e-mail]

203 E. Daugherty

Webb City, MO 64870

D268-WARRANTY-DET-A

08/14

Printed in USA

8525-M310-O1 Rev E  612X Series and 633X Series

15

16

8525-M310-O1 Rev E  612X Series and 633X Series