Carcam G-800 Installation & User Manual
Carcam.ie G-800 Dual Mirror Camera – incorporating Reverse Parking Function
Installation & User Manual
Thank you for purchasing this high definition rear view mirror dual car camera. This is a
high quality and stylish product which should not adversely affect the original look of
your car.
The device is a professional high definition car camera, with dual front & rear cameras
and the addition of an automated car reversing function. It can record high resolution
video and take super clear pictures and store these to the 32GB Class 10 Micro SD Card
as supplied by Carcam.ie.
This manual includes the usage, specification and notes about the device. Read it carefully
before using the product to ensure you get the most from it and keep the user manual safe
for future reference. Carcam.ie will also keep a copy of the manual on our website.
If after reading the manual, you are unsure about any function or operation of the camera,
contact support@carcam.ie with your problem and one of our staff will reply by email or
phone to assist you.
Accessories：
Fixing Belts X 2
Car Rear Camera X 1
Cable for Connection to Car Reversing Circuit X 1
Car Charger X 1
USB Cable X 1
User Manual X 1
1. Product Features
1. Adjustable 170 degree ultra-wide angle front lens.
2. The rear camera will work automatically once plugged in.
3. When the ignition is switched on, the device will automatically turn on and begin to
record.
4. Seamless loop recording means the device will not miss any data while driving.
5. Once the rear camera is connected into the reversing light circuit (professional
recommended), when reverse is selected, the screen will display the rear camera view
and a guide grid for safer reversing.
6. The camera also supports manual reversing function. The screen will automatically
display dual cameras (PIP) on start up. Pressing the “Up” button will switch to rear
camera only, which can assist with reversing in the absence of the connection in (5) above.
7. The mirror houses a 4.3inch high definition LCD screen.
8. G-Sensor function. In the event of an accident involving the vehicle, the video will be
saved and not over written in the loop recording cycle.
9. Parking Sensor. The camera will switch on and record for circa 20 seconds in the event
of the car being hit in a car park situation.
10. Motion sensor. When parked the camera will switch on and record if the front lens
detects motion outside.
11. LED lights around the front lens to assist with night vision in close proximity.
12. Stylish look & easy installation.
2. Appearance of the interface
1. LCD Screen
2.Power Button
3.MENU Button
4.MODE Button
5.Up Select Button
6.Down Select Button
7.OK Button.
8. GPS (Non use).
9. Micro SD Card Slot
10. AV Interface
11. USB/Charging
12. Speaker
13. Reset Button
14. Back Holder
15. LED fill in light
16. Lens
Button Function ：
ON/OFF Button
Long press to turn on/off.
When powered up, short press to turn on/off infrared
fill in light.
MENU Button
Short press to enter function setting menu. (Note: you
can only enter this menu when the camera is not
recording, so press the OK button [button 7] to stop
recording and then the MENU button to enter the
Menu). When in the Menu, pressing the Menu button
will exit the menu setting.
In images or video browsing mode, press the Menu
button to delete option.
MODE Button
In standby mode, press it to record, take photos and
replay.
When recording, long press the MODE button to lock
the video. (Note: This is an option if you and the
camera witness something which you’re not
involved in, but could offer evidence if required).
Up Select Button
In the dual camera recording mode, press to switch the
camera display from Front, to Rear, to Dual display.
In the MENU mode, press to navigate the menu
options.
This button is also used to browse the pictures in the
picture replay mode.
In the video replay mode, press to fast backward.
Long press this button to switch motion detect from
on/ off.
Down Select Button
In the dual camera recording mode, press to switch the
camera display from Front, to Rear, to Dual display.
In the MENU mode, press to navigate the menu
options.
It’s used to browse the pictures in the picture replay
mode.
In the video replay mode, press to fast forward.
Under the standby and recording mode, short press
Down Select Button to switch audio recording from
on/off.
Long press it, to open parking monitor.
OK Button
While recording video and taking pictures, press to
start/stop.
In the MENU mode, press to conform Menu setting.
In the video replay mode, press to play the video;
Note: The device does not support GPS at the moment.
3．Specification
CMOS
1.2M CMOS Sensor,
1/4 inch Light-sensing
Surface Area
Motion
detection
Built-in Sensitive Motion
Detection
Lens
Dual lens, 170 degree
ultra-wide angle lens.
Gravity
sensor
Three-dimensional
Vibration Sensor, Save the
Recording Video
LCD
4.3inch high definition
LCD screen
Audio
Built-in
Microphone/Speaker(AAC)
Photo Format
JPG
Cycle
recording
Seamless continuous
recording. New file
automatically covers oldest
file when SD card is full.
Locked files can’t be overwritten.
Picture resolution
8.0MP
Language
Multi language
Video resolution
Front Camera 2.0MP
1920*1080P（FHD）
Back Camera 1.0MP
720*480P
Battery
Built-in lithium ion polymer
battery
Storage
SDHC, Support up to
32G TF Card
DDR
1G DDR3
Video format
H.264 Compression
Code,MP4 Play format
Operating
temperature
-20℃ TO 70℃
CPU
4 core
Aperture
2.0
Fill-in light
LED
4．Installation instructions
Notes：
1. Use the back straps in accessories to fix the camera to the original car's rear-view
mirror. Depending on the size of the original car mirror, you may have to offset the mirror
slightly. (NOTE: once installed, check the clearance to the sun visors? In a small number of
installations, because the mirror is wider than the original in may snag the sun visor when
it’s being lowered. Check this now, so you’re aware if the mirror needs to be adjusted when
lowering this visor)
2. Connect the car charger to the 12V socket (cigarette lighter), to charge the car camera
(The device only supports charging by USB5V). The car charger has a supplementary USB
socket built into it so you can plug another device in while it’s in use.
3. As long as the car camera is connected to the 12V socket switching on the ignition will
power up the camera and it will start recording automatically. When the ignition is
switched off, the car camera will stop recording and save the recorded data.
4. To use the rear camera it only needs to be plugged in to begin recording. Ideally, the rear
camera should be installed at the top and in the centre of the rear window.
5. Please note the device should be connected to the car charger or DC power when in use
as it requires reasonable power. When disconnected, the internal battery can only power
the unit for a short time. Please also use the original car charger to charge the car camera.
Loading...