Carbine PLUS-5600 User Manual

Model: PLUS-5600
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
© Copyright 2002 Magnadyne Corporation
MANUAL
R
Vehicle Security
PLUS5600UM 2/1/02 11:48 AM Page 1
Lock
Unlock
Panic
Aux
2
Congratulations on your purchase of a quality Carbine Automotive security system. Carbine automotive security products have been designed to provide the consumer with a product that is technologically superior and will provide years of trouble free operation.
The information enclosed will provide a ready reference of the operation and maintenance of your new Carbine security system.
Remote Control Transmitters
1. Exit the vehicle and close all entrances.
2. Press and release the LOCK button on the transmitter. The security system will respond as follows: A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash at a steady rate. C. The parking lights will flash one time. D. The starter disable device will become armed and the vehicle engine will not crank E. All protected entrances are armed. Note: If the dome light is on or a sensor is active at the time you arm your security system, You will
hear the horn/siren beep one time and then you will hear another beep from the horn/siren about 5 seconds later. This second beep is the active sensor warning indicator. This second beep tells you that the alarm is armed but one of the sensors has been temporarily deleted because it was on at the time the alarm was armed.
The security system is now fully armed!
Security System Operation: (Using the transmitter to arm the security system)
Regular
A
R
Passive
B
Note: The following information is valid only if your security system has been programmed to automatically arm.
1. Turn off the ignition key and exit the vehicle.
2. Close all protected entrances. After the last protected entrance is closed the horn/siren will chirp one time and the LED indicator will begin to flash fast. The fast flashing LED indicates that the automatic arming timer is counting down and the security system will become armed within 30 seconds. After 30 seconds has passed, the security system will respond in the following manner:
Automatic Arming (Without Using the Transmitter)
Lock Unlock
Panic
Aux
Passive
Unlocking
PLUS5600UM 2/1/02 11:48 AM Page 2
A. The horn/siren will chirp one time. B. The LED indicator will begin to flash slower. C. The parking lights will flash one time. D. All protected entrances are armed.
Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming timer. After closing the entrance the timer will begin counting again from zero.
Note 2: If the vehicle has a delayed interior lighting system, the automatic arming timer will start counting after the interior lighting has turned itself off. This could add up to 45 seconds to the total automatic arming countdown time. (Up to 75 seconds total arming delay)
The security system is now fully armed!
3
Automatic Arming (Without Using the Transmitter)(Continued)
1. Press and release the UNLOCK button on the transmitter. The security system will respond as follows: A. The horn/siren will chirp two times.
B1.The LED indicator will be off. (Only if Auto Arming is programmed off) B2.The LED indicator will be flashing very fast. (Only if Auto Arming is programmed on) C. The parking lights will flash two times.
Note: If you are disarming the security system after it has been triggered and the horn/siren is sounding, the disarm chirps are automatically deleted.
Disarming the Security System Using the Passive Transmitter (B)
Note: When using the passive transmitter the on/off switch must be in the “on” position.
A. Walk toward your vehicle and the security system will respond the same as pushing the unlock
button on the transmitter..
The security system is now disarmed!
Disarming the Security System Using the Transmitter
Removable Valet/Override Switch Operation
Caution: Be careful and not to bend the override switch pins when put it into the housing. Also note the
override switch can only go into the housing one way.
See diagram to note shape of housing.
"Off"
Positon
"On"
Positon
To provide a higher level of protection, your Carbine security system is supplied with the patented removable valet switch system. The removable valet switch is used to override the security system in the event that the transmitters are lost or fail to operate and to put the security system in non-operational mode (valet) for vehicle servicing etc.
PLUS5600UM 2/1/02 11:48 AM Page 3
Loading...
+ 5 hidden pages