Page 1
TV-Free
Video-in-motion Interface
TF-MMI
compatible with Audi MMI 2G/3G/3G+
and VW RNS850
navigation systems
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
Version 28.11.2012 TF-MMI
Page 2
Page1
MOST®-Box
HW_____ SW_____
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
2. Installation
3. Activation of the video-in-motion function
3.1. Deactivation of the video-in-motion function
4. Specifications
5. Technical support
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
Version 28.11.2012 TF-MMI
Page 3
Page2
Requirements
Vehicle A1, A5 (B8), A6 (4F), A6 (4FH allroad), A7 (4G), A8 (4E/4H), Q5,
Q7 (4L), VW Touareg 2010
Navigation Audi MMI 2G/3G/3G+ and VW RNS850
Audi CD changer
Radio Module
Audi CD changer
female 8pin connector
1.2. Check compatibility of vehicle and accessories
2. Installation
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle is
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
1. Remove the factory CD-changer out of the glove
box. You have to remove the navigation-computer,
if there is no cd-changer in the vehicle.
2. The interface has to be plugged into the fibre-optical ring.
The direction arrows have to be obeyed when connection
the fibre-optical cables.
3 The plug and play power connector should be installed
between the power connector of the factory CD-changer.
If used in vehicles without factory CD-changer cut off the plug and
play power connectors and connect red to +12V permanent
current and black to ground.
Version 28.11.2012 TF-MMI
Page 4
Page3
3. Activation of the video-in-motion function
The video-in-motion function is activated permanently without disturbing the navigation
performance.
3.1. Deactivation of the video-in-motion function
The blue wire of the harness is used to deactivate the video-in-motion function:
+12V blue wire = video-in-motion function is deactivated
0V blue wire = video-in-motion function is activated permanently
4. Specifications
Operation voltage 10.5 – 14.8V
Stand-by power drain 4mA
Power consumption 0,7W
Temperature range -30°C bis +80°C
Weight 74g
Measurements (box only) B x H x T 105 x 30 x 78 mm
5. Technical Support
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.
email support@caraudio-systems.de
Version 28.11.2012 TF-MMI
Loading...