Page 1
Version 24.02.2012 C2-RNSE
c.LOGiC-Interface
C2-RNSE
For navigation systems
Audi Navi Plus RNS-E
Only for vehicles WITHOUT factory rear-view camera
Product features
• full plug and play multimedia interface
• 2 AV-inputs with separate IR-control channel
• integrated into and controllable by vehicle infotainment
• control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, …
• after-market rear-view camera input
• automatic switching to rear-view camera input (optional coding necessary to switch from
OEM-modes)
• rear-view camera power (+12V max 1A)
• rear-seat-entertainment AV-output
• power on remote out trigger signal (+12V max 1A) to switch on connected devices
• video-in-motion
Page 2
Version 24.02.2012 C2-RNSE
Page1
Contents
1. Prior to Installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the dip switches of the CAN-box TV-400
1.4. Setting the dip switches of the Interface-box C2C-M200
1.4.1. Automatic switching to rear-view camera
1.4.2. Deactivating c.LOGiC AV2-input
2. Connection schema
3. Installation
3.1. Interconnecting Interface-box, CAN-box and harness
3.2. Connections to head-unit
3.3. Connecting peripheral devices
3.3.1. AV-source(s)
3.3.2. Installing AV-source’s IR-sensor additionally
3.3.3. After-market rear-view camera
3.3.4. After-market rear-seat-entertainment
4. Operation
4.1. Activation of the video-in-motion function
4.2. Selecting the c.LOGiC as current AV-source
4.3. Switching between AV1 and AV2
4.4. Assigning device controls
4.5. Remote functions
4.6. Picture settings
5. Specifications
6. Technical support
Appendix A – Device control table
Page 3
Version 24.02.2012 C2-RNSE
Page2
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
If remote function for the connected devices shall be used, additional an IR-
remote cable and Y-adapter are needed, see chapter AV-source(s).
CAN-box
TV-400
HW_____
SW _____
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Interface-box
C2C-M200
HW_____ SW_____
Harness
C3C-RNSE
Page 4
Version 24.02.2012 C2-RNSE
Page3
dip switches
interface-box
1.2. Check compatibility of vehicle and accessories
1.3. Setting the dip switches of the CAN-box TV-400
1.4. Setting the dip switches of the Interface-box C2C-M200
The default dip switch settings of the Interface-box
need to be changed ONLY if an after-market
rear-view camera shall be connected or if the AV2
of the c.LOGiC shall be deactivated. The dip
switches are located inside the Interface-box.
For changes it is necessary to open the box.
Default settings are:
dip1 = ON, dip2 = OFF, dip3 = OFF
Note: Instead of dip switches, there might be jumper 1 to 3.
1.4.1. Automatic switching to rear-view camera
If an after-market rear-view camera shall be connected, in order
for the c.LOGiC to automatically switch to its camera input
on engaged reverse gear,
set dip2 = ON (up).
Note: With after-market cameras, automatic switching works only from c.LOGiC mode. For
automatic switching from OEM modes, it is necessary to code the head-unit to rear-view
camera per diagnosis computer.
Requirements
Vehicle Audi, Lamborghini
Navigation Audi Navi Plus RNS-E all-in-one navigation 16:9
Limitations
Factory-TV-tuner Must NOT be installed.
After-market rear-view Only compatible with NTSC-cameras.
camera Automatic switching to camera from OEM mode only works
after coding the head-unit to rear-view camera per diagnosis
computer (Only possible on RNS-E with minimum software 550
and till year 2010).
Video-in-motion function Navigation does NOT work while VIM is activated.
All vehicles dip 1 OFF, dip 2 OFF, dip 3 OFF
Page 5
Version 24.02.2012 C2-RNSE
Page4
1.4.2. Deactivating c.LOGiC AV2-input
If only one AV-source shall be connected to the c.LOGiC, we
recommend to disable the AV2-input, to avoid customers switching
by mistake to black/no picture of the AV2-input. In order to disable
the AV2-input of the c.LOGiC,
set dip1 = OFF (down).
2. Connection schema
Page 6
Version 24.02.2012 C2-RNSE
Page5
3. Installation
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Place of installation is behind the head-unit.
3.1. Interconnecting Interface-box, CAN-box and harness
Plug harness C3C-RNSE into 8pin Molex of CAN-box TV-400..
Plug harness C3C-RNSE into 14pin Molex of Interface-box C2C-M200.
Plug female 18pin AMP-connector of C3C-RNSE into male 18pin AMP-socket of
Interface-box C2C-M200.
Page 7
Version 24.02.2012 C2-RNSE
Page6
3.2. Connections to head-unit
Remove the head-unit from the dash-board.
Transfer female Quadlock connector from the back of the head-unit to male
Quadlock connector of harness C3C-RNSE.
Plug female Quadlock connector of C3C-RNSE into male Quadlock socket of
head-unit.
Plug female 32pin AMP-connector of C3C-RNSE into male 32pin AMP-socket of head-
unit.
Note: If the 32pin AMP-socket of the head-unit is already occupied, the vehicle probably has
a factory rear-view camera or a factory TV-tuner. In case of a factory tuner, it must be
uninstalled: disconnect the female 32pin AMP-connector of the factory harness and
disconnect all wires from the factory TV-tuner. In case of a factory rear-view camera you
have ordered/received the wrong product, call for support.
3.3. Connecting peripheral devices
It is possible to connect up to 2 after-market AV-sources, an after-market rear-view camera
and rear-seat-entertainment to the c.LOGiC Interface.
Before final installation of the peripheral devices, we recommend to test-run the c.LOGiC
functions to detect incompatibility of vehicle, navigation, factory accessories or peripheral
devices as soon as possible.
Page 8
Version 24.02.2012 C2-RNSE
Page7
3.3.1. AV-source(s)
The c.LOGiC interface has the possibility to connect and remotely control by navigation
buttons up to 2 pre-programmed devices. The device list in the device control table
(Appendix A) shows the pre-programmed remote channels and the related IR-remote cables
STA-xxx which must be ordered separately for the control of the device.
Using the respective STA-xxx IR-control cable, interconnect the blue (yellow) female
3pin AMP connector of harness C3C-RNSE and the IR-port of the AV-source 1 (AVsource 2).
Using an RCA-cable, interconnect the female RCA-port AV1 (AV2) of the Interface-box
C2C-M200 with the AV-output of the AV-source 1 (AV-source 2).
The pink ACC-output wire (+12V max 1A) of harness C3C-RNSE can be connected to
the ACC-input wires of the connected device to switch it on. It carries +12V when the
head-unit is running.
Page 9
Version 24.02.2012 C2-RNSE
Page8
3.3.2. Installing AV-source’s IR-sensor additionally
Additionally to the control via OEM navigation, it is possible to install the original IR-sensor
of a connected device. By using the respective Y-adapter (e.g. STA-Y35MM or STA-RJ12) for
the IR-Port of the connected device, the controls of navigation AND device’s IR-sensor can be
connected and used simultaneously. Installation of the IR-sensor is recommended as the
controls via navigation are limited, and not all functions may be covered.
3.3.3. After-market rear-view camera
Connect the video RCA of the after-market rear-view camera to female
RCA connector R-CAM IN of Interface-box C2C-M200.
Connect the green wire of C3C-RNSE to the camera power supply (+12V max. 1A)
The green wire is high (+12V max. 1A) when reverse gear is engaged. Connect the
loose white-brown wire of the female Quadlock connector of harness C3C-RNSE to
the green wire of harness C3C-RNSE, too.
Note: Only compatible with NTSC-cameras.
Automatic switching on reverse gear from OEM mode to camera input only works
after coding the head-unit per diagnosis computer (Only possible on RNS-E with
minimum software 550 and till year 2010).
If coding is done by diagnosis PC, code rear-view camera to value 1 in channel 04,
controller 56. After coding the vehicles needs to be locked for at least 66 minutes to
reach general sleep mode.
Page 10
Version 24.02.2012 C2-RNSE
Page9
3.3.4. After-market rear-seat-entertainment
Using RCA-cables, connect the rear-seat-entertainment to the female RCA-connector
VIDEO OUT of Interface-box C2C-M200.
Note: As the output is a full output, not shared with the video signal for the
navigation system, splitting the video with an RCA Y-cable might give a good enough
picture for two rear-seat-entertainment monitors. If not, or if connecting more than
two monitors, use a video splitter.
4. Operation
4.1. Activation of the video-in-motion function
The video-in-motion function is activated by long-pressing the “next track” button when in
TV-mode. As confirmation, the head-unit’s button illumination will blink a few times slowly.
Repeat to deactivate, confirmation are a few fast blinks. While the video-in-motion function
is active, the navigation will not work. After ACC is switched off, the video-in-motion
function will be automatically deactivated.
4.2. Selecting the c.LOGiC as current AV-source
Push the CD/TV button of the head-unit to choose the
c.LOGiC as current AV-source.
Page 11
Version 24.02.2012 C2-RNSE
Page10
4.3. Switching between AV1 and AV2
After selecting the c.LOGiC as current AV source,
longpress the knob to switch between AV1 and AV2.
Note: If AV2 is deactivated (see chapter chapter Deactivating
c.LOGiC AV2 input), it is not possible to switch to the c.LOGiC’s
AV2.
4.4. Assigning device controls
After selecting the c.LOGiC as current AV source, switch to the c.LOGiC’s AV1. Now longpress
key SETUP. The FIS will display “TV 1” and “RC01”. Turn right knob until the device-related
IR-code as described in device control table for AV1 (appendix A) is reached. Push right knob
to confirm the assignment. Longpress right knob to assign device control for AV2. The FIS will
display “TV 2” and “RC01”. Turn right knob until the device-related IR-code as described in
device control table for AV2 (appendix A) is reached. Push right knob to confirm the
assignment.
Note: The IR-control channel TV1 is preset to RC-Code 41 compatible DVB-T tuners and TV2
is preset to RC-Code 09 for the usbLiNK.
If the AV2 is deactivated (see chapter chapter Deactivating c.LOGiC AV2 input), it is not
necessary, nor possible to assign device controls.
4.5. Remote function
The button assignment table shows which functions of the connected devices can be
executed by head-unit buttons. Once an AV-input is activated, the head-unit button in the
left column will execute the function described in the corresponding device column. The
function description equals the remote control buttons of the optional c.LOGiC remote
control or the additional device. On the additional device the writing may vary (e.g. AV
instead of Source).
Page 12
Version 24.02.2012 C2-RNSE
Page11
4.6. Picture settings
To enter the picture settings menu longpress the RETURN button.
The picture settings menu always starts with the
brightness settings. The respective current picture
value is displayed on the instrument panel.
Press the knob to change from brightness to
colour and contrast (after contrast, the interface
starts again with brightness).
Turn the knob to change the current picture value.
To quit the settings menu press RETURN-button.
Button assignment table c.LOGiC Audi Navi Plus RNS-E
Head-
unit
button
DVB-T
USB-LiNK
DVD-player
DVD-
changer
iPod®-control
Analog-tuner
1
CH -
TRACK -
TRACK -
TRACK -
TRACK -
CH -
1 long
EPG
POWER
PBC
PBC
SHUFFLE
FM
2
CH +
TRACK +
TRACK +
TRACK +
TRACK +
CH +
3
OK
OK / PLAY
OK
OK
OK
MODE
4
↑ ↑ ↑ ↑ ↑
VOL +
5
↓ ↓ ↓ ↓ ↓
VOL -
6
→ → → → →
CH +
6 long
SCAN
VOL+
PLAY
PLAY
PLAY
SCAN
7
← ← ← ← ←
CH -
7 long
POWER
VOL-
AV
DISC
EJECT
MODE
8
EXIT
EXIT
STOP
STOP
PLAY
MUTE
9
MENU
SETUP
SETUP
SETUP
LIGHT
ADJUST
Page 13
Version 24.02.2012 C2-RNSE
Page12
5. Specifications
Operation voltage 10.5 – 14.8V DC
Stand-by power drain <1mA
Operation power drain 240mA
Power consumption 3W
Temperature range -30°C to +80°C
Weight 202g
Measurements (box only) B x H x T 90 x 30 x 105 mm
6. Technical Support
Caraudio-Systems Vertriebs GmbH NavLinkz GmbH
manufacturer/distribution corporate sales/tech dealer-support
Rheinhorststr. 22 Eurotec-Ring 45
D-67071 Ludwigshafen am Rhein D-47445 Moers
phone +49 180 3 907050
email support@caraudio-systems.de
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.
Loading...