CaptiveAire 610-A Installation Manual

READ CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE OR SERVICE YOUR MOTOR PACK! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

DESCRIPTION

Your Backdraft Damper or Ceiling Shutter Motor Pack is designed to automatically open the shutter when the fan is turned on and closes securely when the fan is turned off. This single phase motor pack is equipped with actuator, motor bracket, linkage, and mounting hardware (fasteners).

INSTALLATION INSTRUCTIONS & PARTS LIST

BACKDRAFT DAMPER AND CEILING SHUTTER MOTOR

MODELS 411, 610-A, 611

SPECIFICATIONS:

Figure 2 – Installation (611)

INSTALLATION

Model 610-A, see figures 1, 3 & 4 for reference. Model 411, 611, see figures 2, 3 & 4 for reference.

1. Using bolt, nut and lock washer provided, fasten motor plate to shutter frame and tighten.

2. Attach motor arm linkage to second hole as show. (Shutter must be in closed position when mounting motor).

3. Make proper wiring connections. NOTE: UNIT IS NOT FIELD SERVICABLE AND SHOULD

BE REPLACED AS AN ASSEMBLY.

Figure 1 – Installation (610-A)

MOTOR WITH

LEADS

MOTOR ARM

LINKAGE

IMPORTANT

LINKAGE POSITION

TIE ROD

NUT &

BOLT

MOTOR

BRACKET

MOTOR ARM

2ND BLADE FROM TOP

NUT

TIE BAR

WASHER

SCREW

USE 2ND HOLE ABOVE BLADE & TIE BAR CONNECTION

MOTOR & TIEBAR CONNECTION

SHUTTER CLOSED

SHUTTER OPEN

MOTOR ARM LINKAGE (MOUNT TOWARDS OUTSIDE OF FRAME)

Motor Pack Power Supply Running Stall Lead Installed Unit Dimension Part Number Required AMPS Torque Length H W D

MTR-611, 610 115/230V, 60 Hz .20/.14 41 in.lbs/47 in.lbs. 6” 8 1/2” 4 1/2” 7.375” MTR-611 24V 24V, 60HZ 1.02 42 in.lbs 6” 8 1/2” 4 1/2” 7.375” MTR-611 208V 208V, 60Hz 0.10 42 in.lbs 6” 8 1/2” 4 1/2” 7.375” MTR-611 277V 277V, 60Hz 0.12 50 in.lbs. 6” 8 1/2” 4 1/2” 7.375” MTR-611 460V 460V, 60 Hz 0.11 48 in.lbs 6” 8 1/2” 4 1/2” 7.375” MTR-611-E 115/230V, 60 Hz .20/.14 41 in.lbs/47 in.lbs. 6” 8 1/2” 4 1/2” 7.375”

Note: (MTR-611-E includes end switch; 50 Hz versions of above motor packs available but not UL rated). (*) Motor is single-phase, continuous duty with a 40°C, (104°F) maximum ambient temperature.

AIR CONDITIONING PRODUCTS CO.

SHUTTERS DAMPERS LOUVERS

MODELS 411, 610-A, 611

610A-611 0194

01280

GRD.

INSULATED

Figure 3 – Wiring Diagram – 120V, 60 Hz

FAN

MOTOR

SHUTTER MOTOR

GRD.120V

POWER

SUPPLY

LINES

SWITCH

BLACK

WHITE

GREEN

RED

GRD.

Figure 5 – Wiring Diagram – 24V; 480V, 60 Hz; 277V, 60 Hz;

208V, 60 Hz

FAN

MOTOR

SHUTTER MOTOR

POWER

SUPPLY

LINES

SWITCH

BLACK

GREEN

GRD.

INSULATED

Figure 4 – Wiring Diagram – 240V, 60 Hz

FAN

MOTOR

SHUTTER MOTOR

GRD.240V

POWER

SUPPLY

LINES

SWITCH

BLACK

RED

GREEN

WHITE

GENERAL SAFETY INFORMATION

1. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).

2. Motor must be securely and adequately grounded. This can be accomplished by wiring with a grounded, metal-clad raceway system, by using a separate ground wire connected to the bare metal of the motor frame, or other suitable means.

3. Always disconnect power source before working on or near a motor or its connected load. If the power disconnect point is out-of-sight, lock it in the open position and tag to prevent unexpected application of power.

4. Protect the power cable from coming in contact with sharp objects.

5. Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces, or chemicals.

6. Make certain that the power source conforms to the requirements of your equipment.

Ref. Part No. Description No. Qty.

1 Motor Varies 1 ea. 2 Motor Bracket 50003 1 ea. 3 Motor Crankarm 50015-A 1 ea. 4 Return Spring FPR 556-104 1 ea. 5 Spring Post With Screw 611-116 1 ea.

PARTS LIST

LIMITED WARRANTY

All products manufactured are warranted by Air Conditioning Products Company (ACP) to be free from original defects in workmanship for a period of one year from date of shipment, under conditions of normal use and service. ACP will replace or repair any defective parts upon return to our plant, freight prepaid. This limited warranty will, in no way, include the payment of labor charges for field replacement of defective parts, installation, repairs of adjustments, or any other work done. Back charges will not be accepted for any reason unless ACP has given prior written permission, nor will ACP be responsible for consequential damages of any character, no limited warranty expressed or implied will supersede the foregoing.

Manufactured for Air Conditioning Products Co.

30350 Ecorse Raod • Romulus, MI 48174

Figure 8 – Parts Diagram