Capricorn RC LabC03 Instruction Manual

LabC0

3

Instruction Manual rel. 1.

0

(06/2014)

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Symbols -

Made in Italy

02

WARNING

This radio control model is not toy.
First time builders should seek the advice of experienced modellers before beginning assembly and/or if they do not fully
understand any part of the construction.We highly advise to read the instruction manual before assembly, and to always
keep it at hand for reference. Take care before operating this model; you are responsible for its assembly and safe
operation. The extreme performance of this model could be understimated by inexpert drivers and could damage objects
and/or people. Assembly this kit only in places out of children's reach!
CAPRICORN RC is not responsible for any damage or harm caused by improper use or assembly.
CAPRICORN RC and its distribution network are not responsible for any damage caused by shipping or handling.
Eventual parts missing from the kit or flawed must be reported within two weeks of purchase to your local hobby
shop or distributor. For best performance, we highly advise to only use original authentic CAPRICORN RC parts.
For customer support and service please contact your local hobby shop or agent from whom you purchased this item.
Contents of box may slightly differ from the pictures shown. Construction tools, body, fuel, radio system and servo,
engine, muffler and battery pack are NOT INCLUDED unless otherwise stated.

WARNING

This radio control model is not toy.
First time builders should seek the advice of experienced modellers before beginning assembly and/or if they do not fully
understand any part of the construction.We highly advise to read the instruction manual before assembly, and to always
keep it at hand for reference. Take care before operating this model; you are responsible for its assembly and safe
operation. The extreme performance of this model could be understimated by inexpert drivers and could damage objects
and/or people. Assembly this kit only in places out of children's reach!
CAPRICORN RC is not responsible for any damage or harm caused by improper use or assembly.
CAPRICORN RC and its distribution network are not responsible for any damage caused by shipping or handling.
Eventual parts missing from the kit or flawed must be reported within two weeks of purchase to your local hobby
shop or distributor. For best performance, we highly advise to only use original authentic CAPRICORN RC parts.
For customer support and service please contact your local hobby shop or agent from whom you purchased this item.
Contents of box may slightly differ from the pictures shown. Construction tools, body, fuel, radio system and servo,
engine, muffler and battery pack are NOT INCLUDED unless otherwise stated.

L/R

Symmetrical
Mounting

2x

Assemble as many
times as specified

1 2
3 4

Assemble in the
specified order

Note:

TEXT....

Be Careful

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Tools & Equipment -

Made in Italy

03

Tools needed for assembly (NOT INCLUDED)

Parts for model completion and Start (NOT INCLUDED)

Also required: Starting Box - Nitro fuel - Fuel bottle - Glower - Plycarbonat body

Hex Wrench
1,5/2/2,5/3mm

Box Wrench
7mm

Reamer

Wrench Glowplug
& Cluthnut

Cutter

Pliers

Adjustable Pliers

Glass or Vinyl
Tape

Engine

Air Filter & Oil

Exhaust System

Transmitter

Receiver

Steering & Throttle
Low Profile Servos

RX Battery Pack

Battery Charger

Parts List

Rif. n° Code

1 1

Cap18510

2 1

Cap18509-X

3 1

Cap18507

4

1 Cap18508

5

1

Cap18512

6 1

Cap18504

7

1

Cap18502

8 1

Cap14042

9 1

Cap14033-6

10 1

Cap14036

11 1

Cap16085-B

Step 1.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Shock Damper ­ BAG 1

Made in Italy

04

1

2

3

4

5

6

8

9

10

11

7

13

4x

Big Bore
Code Cap29148-6

Big Bore
Code Cap18506-X

Big Bore
Code Cap18503

Big Bore
Code Cap18501

11,5

Big Bore

Std Bore

Option

Code
Cap18505

Apply Oil before assembly

Silicon Oil #600

Parts List

Rif. n° Code

1 1

Cap171215

2 1

Cap16027
3 1 Cap16098F
4

1

Cap14030
4 1

Cap14042
5

2

Cap16086

Step 1.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Shock Damper ­ BAG 1

Made in Italy

05

4x

Big Bore Spring
Code Cap29165

Big Bore 13x1,5
Code Cap29159

Big Bore
Code Cap20017

Big Bore

Std Bore

Apply Oil before assembly

5

4

1

2

3

5

12x1,5

Rear Spring
Code Cap16098R

5,8 ball

5,8 ball

7,0 Front
4,0 Rear

1,5 Front
2,0 Rear

4x

2x

2x

Front Spring

Parts List

Rif. n° Code

1 1

Cap16014

2 1

Cap18027

3 1

Cap16065

4 1

Cap16033

5

1

Cap171015

6 1

Cap16028

7

2

Cap16019

8 1

Cap 2212

9 1

Cap15005P

10 2

Cap17030
11 3 Cap16086
12 1

Cap17029

Step 2.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Servo Saver ­ BAG 2

Made in Italy

06

7

1

2

11

12

11

10

3

9

4

5

6

7

8

11

10

12

Option
Ackermann Inserts

Initial Setting

0,5:1,0 Spring preload

5x8x2,5

5,8 ball

5,8 ball

3x6

3x6

10x1,5

5x8x2,5

Oil

Parts List

Rif. n° Code

1 2

Cap16012

2 2

Cap 415

3 2

Cap16018

4 2

Cap17026

5

1

Cap 2029-B

6 2

Cap15010

7

2

Cap 2013

8 1

Cap 2216

9 1

Cap-shim 3

10 1

Cap16080-D

11 1

Cap17006

Step 3.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Belt Tensioner Set ­ BAG 3

Made in Italy

07

5x10x4

3x12

3x12

5x10x4
Flanged

10

6

5

1

2

3

4

8

7

4

3

2

1

6

11

7

9

3x3
Thread Lock

5x10x4
Flanged

5x10x4

3x6x2,5
Flanged

3x6x2,5
Flanged

shim
3x5x0,3

Use if necessary

To loosen side belt

To tighten side belt

Move Freely

.

.

.

A

B

Parts List

Rif. n° Code

1 1

Cap 2190

2 2

Cap16020

3 1

Cap18071

4 1

Cap18080

5

2

Cap17016

6 1

Cap14024K

7

1

Cap14024K

8 1

Cap14026K

9 1

Cap14026K

10 2

Cap17002

Step 4.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Middle Shaft Holder ­ BAG 4

Made in Italy

08

6x13x5

2x12 Pin

6x10x0,5
Black Plastic

2x12 Pin

6x13x5

7

6

4

2

2

1

5

8

9

10

10

3

5

Z25 Initial Setting
Z26 Code Cap14027K

Z19

Parts List

Rif. n° Code

1 1

Cap16024

2 1

Cap14017

3 6

Cap17038

4 1

Cap14020

5

1

Cap16025

6 1

Cap16001

7

1

Cap16074

8 1

Cap17009

9 2

Cap16062

10 2

Cap14032

11 2

Cap16011

12 2

Cap16031

13 2

Cap17021

14 2

Cap16079

15 1

Cap17002

Step 5.0

Capricorn RC

- 2 Speed gear ­ BAG 5

Made in Italy

22

-

0

0,1

+

14

7

8

6

15

9

10

11

12

13

5

4

1

2

3

14

3

4x3
Thread Lock

6x10x3

6x10x3

2,5x10

3x5

3x5

Z53

Z48

09

Note:
Adjust the 2,5x10 screws in equal mode

One Way Oil

Parts List

Rif. n° Code

1 1

Cap14004B

2 2

Cap16017

3 2

Cap16004

4 2

Cap16026S

5

1

Cap16097

6 1

Cap17015

7

1

Cap 255+

8 1

Cap17006

Step 6.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Hub ­ BAG 6

Made in Italy

10

8,4 pivot

3x3

2

2

6

7

8

4

3

1

5

10x16x4

10x16x4

2x10 Pin

2x L/R

3

4

8,4 pivot

Pivot must move freely

OffSet
+0,75

Parts List

Rif. n° Code

1 1

Cap14002B
2 2 Cap16017
3 2

Cap16004
4 2

Cap16026S
5

1

Cap16063S
6 1

Cap16092
7

1

Cap16096
8 2

Cap17015
9 1

Cap 255

10 1

Cap17006

11 1

Cap17032

12 1

Cap16086

Step 6.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Hub ­ BAG 6

Made in Italy

11

Right Steering Block

2x L/R

1

8

8

5

6

7

11

12

2

2

9

10

3

3

4

4

Left Upright
Code Cap14003B

OffSet
0

3x3

8,4 Pivot

8,4 Pivot

10x16x4

5,8 ball

3x8

2x10 Pin

2x10 Pin

10x16x4

Grease

Pivot
must move freely

.

Parts List

Rif. n° Code

1 1

Cap16077

2 1

Cap17010

3 1

Cap14025K

4 1

Cap14025K

Parts List

Rif. n° Code

1 1

Cap18056
2 1 Cap16013-V2
3 2

Cap18066
4 2

Cap 2070
5

2

Cap18069
6 2

Cap17023
7

1

Cap16021

Step 7.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Brake Set ­ BAG 7

Made in Italy

12

6x12x4

3x10

1

2

3

4

3

5

5

6

7

6

3x10

4

1

2

3

4

Z20

4x4
Thread Lock

Note:
Ensure that the brake system
move freely

Parts List

Rif. n° Code

1 1

Cap14034

2 2

Cap15011

3 2

Cap17031

4 3

Cap17040

5

1

Cap14010L

6 1

Cap15007P

7

2

Cap17032

8 2

Cap17016

9 2

Cap15013

Step 8.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Bodymounts ­ BAG 8

Made in Italy

13

3x8

3x8

9

9

7

7

6

8

5

1

8

2

2

3

3

4

3x8

3x8

2x12 Pin

2x12 Pin

M3 Nut

Initial Position

Parts List

Rif. n° Code

1 1

Cap16081

2 2

Cap14043

Parts List

Rif. n° Code

1 1

Cap16008

2 2

Cap18070-X

3 4

Cap17006

4 2

Cap16019

5

2

Cap16087

Step 9.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Anti-Roll Bar ­ BAG 9

Made in Italy

14

3x3

3x3

3x3

3x3

5x8x2,5

L/R

2x

1

2

3

4

3

2

4

5

3

3

5

5x8x2,5

n2,0

2

1

2

41

30°

left move

right move

Note:
Wire should be flush
with end of pivot ball

Note:
Insert ball berings
and Part 2 before
5,8 pivot ball

5,8 Pivot

5,8 Pivot

Left move side

Parts List

Rif. n° Code

1 1

Cap14014G

2 1

Cap172407K

3 1

Cap17042

4 1

Cap16075

5

1

Cap170520

6 1

Cap17042

7

1

Cap17015

8 1

Cap14045

Parts List

Rif. n° Code

1 1

Cap14014G

2 1

Cap17042

3 1

Cap16075

4 1

Cap170520

5

1

Cap17042

6 1

Cap17015

7

1

Cap14045

Step 10.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front gear differential ­ BAG 10

Made in Italy

15

5x2

15x1

5x10x0,2

2x10 Pin

4

3

1

2

6

8

7

5

5x15x0,3

3

2

1

6

4

5

7

5x10x0,2

2x10 Pin

5x15x0,3

5x2

Oil

Oil

Oil

Parts List

Rif. n° Code

1 2

Cap16056

2 4

Cap14045

3 4

Cap17042

Parts List

Rif. n° Code

1

4

Cap17035

2 1

Cap14028K

3 4

Cap17020

4 2

Cap18018

Step 10.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front gear differential ­ BAG 10

Made in Italy

16

3,5x10x0,2

3

2

1

Note:
Fill differential up to the top
of the pins with silicon oil.
Initial Setting 300.000

- - - - - - - - -

2

3

1

4

4

10x15x4

10x15x4

2,5x8

2x6

Z27

Parts List

Rif. n° Code

1 1

Cap14021G

2 1

Cap172407K

3 1

Cap17042

4 1

Cap16076

5

1

Cap170520

6 1

Cap17042

7

1

Cap17015

8 1

Cap14045

Parts List

Rif. n° Code

1 1

Cap14021G

2 1

Cap17042

3 1

Cap16076

4 1

Cap170520

5

1

Cap17042

6 1

Cap17015

7

1

Cap14045

Step 10.2

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear gear differential ­ BAG 10

Made in Italy

17

5x2

15x1

5x10x0,2

2x10 Pin

5x15x0,3

5x10x0,2

2x10 Pin

5x15x0,3

5x2

Oil

4

3

1

2

6

7

5

8

Oil

3

2

1

6

5

4

7

Oil

Parts List

Rif. n° Code

1 2 Cap16056
2

4

Cap14045

3 4

Cap17042

Parts List

Rif. n° Code

1 4

Cap17035

2 2

Cap18018

Step 10.3

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear gear differential ­ BAG 10

Made in Italy

18

3,5x10x0,2

Note:
Fill differential up to the top
of the pins with silicon oil.
Initial Setting 80.000

- - - - - - - - -

10x15x4

10x15x4

2,5x8

1

2

3

1

2

2

Parts List

Rif. n° Code

1 1

Cap18003

2 1

Cap18002L

3 1

Cap18001

4 1

Cap16086F

Parts List

Rif. n° Code

1 1

Cap18060

2 2

Cap14038-Q

3 1

Cap18078

4 1

Cap18019

Step 11.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Suspension ­ BAG 11

Made in Italy

19

5,8 Flanged ball
!! Flare on top side !!

3x30 Pin

Remove for outdoor
up roll center setting

Rear camber setting

1,5

+.....-

With 1,5 hex wrench
turn for more or less camber

2

1

3

4

2x

L/R

Oil

Oil

Drill n1,5mm
Drill n3mm

Note:
Ensure move freely

Type 1 Insert

2

2

L/R

1

Left part
Code Cap18061

2x

Initial up roll center Position

Right Block

4

2,5x4

3

Parts List

Rif. n° Code

1 1

Cap14008B

2 1

Cap17008

3 1

Cap16086

4 1

Cap17032

5

1

Cap17005

Parts List

Rif. n° Code

1 1

Cap18058

2 1

Cap17018

3 1

Cap14038

4 1

Cap18079

Step 11.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Suspension ­ BAG 11

Made in Italy

20

3x48 Pin

2x

L/R

L/R

Left part
Code Cap18059

2x

2

1

5

4

3

3x8

5,8 ball

3x12

3x8

3,5

1,5

5,0 Rear pivot
4,2 Front pivot

1

2

4

3

Part 3

3x10 Pin

Hard thread lock

-0,5

Parts List

Rif. n° Code

1 1

Cap16069-B

2 2

Cap14038

3 1

Cap18055

4

1

Cap16019

5

1

Cap18057

6 1

Cap16021

7

6

Cap17031

8 2

Cap17023

9 1

Cap15003N

10 2

Cap17029

Step 11.2

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Suspension ­ BAG 11

Made in Italy

21

1

9

6

5

3

8

2

10

7

8

4

10

3x8

3x10

5x8x2,5

BOX

6x12x4

3x10

Big Bore LP Set
Code Cap18031

3x6

3x6

-0,5

Parts List

Rif. n° Code

1 2

Cap18062

2 1

Cap14013RB

3 2

Cap16064

4 1

Cap18068

5

1

Cap17002

Step 11.3

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Transmission ­ BAG 11

Made in Italy

22

3x177 belt

5

2

4

3

1

1

Grease

Note:
Set right and left side
in the same way for a
correct belt tension

Parts List

Rif. n° Code

1 4

Cap17026

2 2

Cap17043

3 2

Cap17024

4 2

Cap17032

5

1

Cap14022-18

6 1

Cap17016

7

1

Cap14023K

8 1

Cap14023K

9 1

Cap17002

Step 11.4

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Suspension ­ BAG 11

Made in Italy

23

3x16

3

9

6

2

4

4

1

1

8

7

5

3x12

3x12

3x8

3x8

3x6x2,5
Initial
Setting

Z18

2x12
Pin

L/R

Parts List

Rif. n° Code

1 1

Cap18063

2 1

Cap16068P

3 2

Cap17032

4

1

Cap16029

5

3

Cap17030

Step 11.5

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Rear Suspension ­ BAG 11

Made in Italy

24

3x6

3x8

3x8

Carbon Plate

5

4

5

5

1

3

3

2

3x6

3x6

Note:
Adjust position for minimum offset
and freely rear Anti-Roll bar movement

Note:
Ensure that the Brake link
move freely

.

Zoom view

Parts List

Rif. n° Code

1 3

Cap16009

2 6

Cap17029

3 1

Cap15014P

4

1

RX Battery

5

3

Cap17035

Step 12.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Battery Holders ­ BAG 12

Made in Italy

25

3x6

3x6

3x6

3x6

3x6

1

1

1

5

5

5

2

2

2

2

2

2

3

4

3x6

2,5x6

2,5x6

2,5x6

NOT INCLUDED

Option Parts

Brass

36gr Code Cap15014C

Special alloy

85gr Code Cap15014S
103gr Code Cap15014S-2,5
123gr Code Cap15014S-3

Parts List

Rif. n° Code

1 1

Cap16036

2 4

Cap17029
3 1 Cap14011RB
4

1

Cap15009P
5

4

Cap17030
6 1

Cap14012RB

Step 12.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Middle Transmission ­ BAG 12

Made in Italy

26

3x6

3x6

Note:
Remove 1mm as shown

3

5

5

6

1

4

5

5

2

2

2

2

3x6

3x6

3x6

3x6

3x390 belt

3x6

3x6

3x186 belt

Parts List

Rif. n° Code

1 1

Cap17030

2 1

Cap18065-R

3 1

Cap18065-F

4 4

Cap17034

5

2

Cap16073

6 4

Cap14041

Step 12.2

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Engine mount & Servo Saver -

BAG 12

Made in Italy

27

3x6

2

3

4

4

4

4

1

6

5

6

69

2x

3x8 Flanged

Initial Setting

Zoom view

F

R

3x8 Flanged

3x8 Flanged

3x8 Flanged

Parts List

Rif. n° Code

1 1

Cap18050

2 1

Cap17011

3 1

Cap14005B

4 1

Cap17005

5

1

Cap16084

6 1

Cap16082

7

1

Cap16051

8 1

Cap17025

9 1

Cap16006-78

10 1

Cap17007

Step 13.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Suspension ­ BAG 13

Made in Italy

28

2x

3x12 Flanged

3

1

2

9

7

10

8

5

6

4

Right Block

L/R

3x12

3x65 Pin

3x3

Left part
Code Cap18051

4x6
Thread Lock

Left part
Code Cap14006B

3,5

+

+

-

-

To adjust Anti-roll bar position

To adjust down stop position

Note:
Ensure that the harm
move freely

Parts List

Rif. n° Code

1 1

Cap18052

2 2

Cap14038-Q

3 1

Cap14007B

4 1

Cap16052

5

1

Cap18019

6 1

Cap14031

Step 13.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Suspension ­ BAG 13

Made in Italy

29

2x

Right Block

L/R

3x40 Pin

Left part
Code Cap18053

.

Note:
Ensure move freely

1

3

2

2

4

5

6

6

6

2,5x4

2,0

1,0

1,5

Set

Initial up roll center Position

2,0

Initial caster position

Type 2 Insert

Drill n1,5mm

Drill n3mm

Parts List

Rif. n° Code

1 1

Cap16007-78

2 3

Cap17031

3 1

Cap17029

4 2

Cap18062

5

1

Cap18074

6 1

Cap17028

7

1

Cap 506XL

8 1

Cap17010

Step 13.2

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Suspension ­ BAG 13

Made in Italy

30

4

6

8

5

7

3

2

2

2

1

3x8

3x8

3x8

3x6

4x4

3x16

Note:
Set right and left side
in the same way for a
correct front belt tension

4

Parts List

Rif. n° Code

1 2

Cap17028
2 1 Cap15002N
3 2

Cap17023

Step 13.3

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Suspension ­ BAG 13

Made in Italy

31

3x10

3x10

3x16

3x16

Big Bore LP Set
Code Cap18030

2

1

1

3

3

Step 13.4

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Front Suspension ­ BAG 13

Made in Italy

32

Note:
Ensure move freely

4

,

7

4

,

7

Grease

Grease

4

,

3

4

,

3

Parts List

Rif. n° Code

1 4

Cap17030

2 4

Cap22019

Step 13.5

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Shock Assembly ­ BAG 13

Made in Italy

33

2

1

1

2

3x6x1,5

3x6

3x6

3x6x1,5

L/R

L/R

~

~

~

~

Initial Position

Initial Position

Front

Rear

Parts List

Rif. n° Code

1 2

Cap15012

2 2

Cap17016

3 2

Cap15013

4

2

Cap17032

5

3

Cap17027

6 2

Cap17030

Step 13.6

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Bodymounts Assembly ­ BAG 13

Made in Italy

34

L/R

Front

Rear

1

3

2

4

5

6

3x8

2x12 Pin

3x6

3x10

Initial Position

Parts List

Rif. n° Code

1 1

Cap18054

2 1

Cap16061

3 2

Cap17031

4 3

Cap14029

5

1

Cap14039

6 3

Cap14029

7

3

Cap17032

Parts List

Rif. n° Code

1 1

Cap 2213

2 2

Cap17019

Step 14.0

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Fuel Tank & F.F.S. ­ BAG 14

Made in Italy

35

2,5x5

3x8

3x8

Type A
Initial Position

1

5

3

7

2

4

6

Note:
Insert into the holes
of radio plate

Note:
2mm shims when using
micro-size RX battery

1

2

Type B

Code Cap 2214

Note:
Reversible use for forward or
backward servo-saver position

Parts List

Rif. n° Code

1 1

Cap16070-B

2 2

Cap17041

3

4

Cap17028

4 2

Cap16048

5

1

Cap17030

6 1

Cap16086

7

1

Cap17005

8 2

Cap14042

1F 1

Cap18072-F

1R 1

Cap18072-R

Parts List

Rif. n° Code

1 2 Cap17030
2

4

Cap17026

3 2

Cap16048

Step 14.1

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Electronics -

BAG 14

Made in Italy

36

3x6

35

95°

1

3

6

2

4

1F

1R

5

8

7

3x16

3x12

Servo shims
1 or 1,5 mm
depending on your
steering servo

5,8 ball

Servo screw

Low Profile
SERVO

16

Note:
Alternative Set for
high size servo

1

3

2

Low Profile
SERVO

3x6

3x12

Parts List

Rif. n° Code

1 1

Cap18073
2 1 Cap14001
3 1

Receiver
4 1

Cap 2186-B
5

2

Cap17026
6 4

Cap18512
7

4

Cap17047

Step 14.2

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Electronics -

BAG 14

Made in Italy

37

2x16

6

1

3

4

7

2

5

Double-sided tape
size 25x15

3x12

"O"Ring

NOT INCLUDED

58:65mm Power extension cable
NOT INCLUDED

Parts List

Rif. n° Code

1 1

Servo arm

2 2

Cap17041

3 2

Cap17021

4 2

Cap17039

5

1

Cap17041

6 1

Cap17041

7

2

Cap16015-1

8 2

Cap17006

9 1

Cap17041

10 1

Cap17041

11 1

Cap17041

Step 14.3

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Gas/Brake Linkage ­ BAG 14

Made in Italy

38

2,5 nut

5

10

8

7

3

8

7

2

6

11

1

9

4

3

2

4

3x3

3x3

2,5x8

2,5x8

2,5 nut

NOT INCLUDED

C

u

t

7

0

:

7

5

m

m

2

:

3

m

m

1

5

m

m

Silicone Tubing

Note:
Insert link in the
brake arm before

Servo screw

Note:
Do not overtighten 2,5 nut
Pivot must rotate freely

Parts List

Rif. n° Code

1 1

Cap16019

2

5

Cap17030

Step 14.4

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Radio plate assembly ­ BAG 14

Made in Italy

39

2

1

3x6

5x8x2,5

Note:
Attach steering linkage
to 5,8 ball on Servo-saver

F

Note:
Remove F screws to Active F.F.S.

Parts List

Rif. n° Code

1 2 Front wheel
2 2 Rear wheel
3

4

Cap 854

Step 14.5

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Wheels assembly ­ BAG 14

Made in Italy

40

3

2

1

3

L/R

NOT INCLUDED

NOT INCLUDED

Parts List

Rif. n° Code

1 1

Cap 405WC

2 1

Cap 408

3 1

Cap 414

4 1

Cap 411M08

5

1

Cap 403-08
6 1 Cap 410WC
7

1

Cap 417
8 1

Cap 409
9 2

Cap 434

10 1

Cap 413

11 1

Cap407WC08

12 2

Cap 413

13 1

Cap 412

14 1

Cap 406-08

15 1

Cap 406-08

16 1

Cap17050

17 1

Cap17045

3x12

17

16

15

13

12

14

10

2

4

5

6

7

1

8

11

Z20

Z15

5x8x2,5

5x10x4

5x7x0,6

5x10x4 Axial

41

3

9

Step 15.0

- Clutch ­ BAG 15

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

42

Step 15.1

- Clutch ­ BAG 15

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

Shim for adjusting flywheel distance

Use the cone that comes
whit your engine

Note:
Hard Tighten the clutch
nut with 10mm Hex Tool

9,3#9,5

43

Step 15.2

- Clutch ­ BAG 15

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

0,5#0,7 Spring preload

44

Step 15.3

- Clutch ­ BAG 15

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

Gap adjust shims

Gap =0

Note:
Do not install
internal shims

Gap =0,5

Note:
install internal
shims appropriately

Adjusting the clutch bell gap

A

A + 0,45#0,55

Push the clutch bell on
to the clutch shoe and
misure A distance

45

Step 15.4

- Clutch ­ BAG 15

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

Z20

(Option Z19 Code Cap17049)

Z15

(Option Z14 Code Cap17044)

Endplay shims

0,1#0,15 Endplay gap

Note:
Large chanfer

n5,2

n5,0

Grease

46

Step 16.0

- Final Assembly View -

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

47

Step 16.1

- Final Assembly View -

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

48

Step 16.2

- Final Assembly View -

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

C03 Default Set-Up Sheet

Front

Rear

.

FRONT

REAR

LEFT RIGHT TYRES LEFT RIGHT

BRAND
SHORE

DIAMETER

OIL
SPRING
PISTON

SHOCK ABSORBERS

ANTI-ROLL BARS

1 ST SPUR GEAR 2 ND

DRIVE TRAIN & D.J. SHAFT

ENGINE

1 ST PINION 2 ND

MIDDLE AXLE PULLEY

25 26 D.J.

TYPE MUFFLER
PLUG NITRO

14 15

19 20

52 53 54 47 48 49

SET-UP SHEET

NAME
DATE
TEMP
TRACK
TRACTION
RESULT BEST LAP

BODY

TYPE

.

CAMBER

TOE / SIDE

WIDHT

GEAR DIFF. OIL

LEFT

RIGHT

CAMBER

TOE /SIDE

WIDHT

LEFT

RIGHT

GEAR DIFF. OIL

ARM POSITION

A B

ACKERMANN INSERTS

10 11 12

GROUND

GROUND

Caster Angle

49

Type 1 Type 2 Type 3

Type 1 Type 2 Type 3

Additional notes

HOLES n

nn

n

Made in Italy

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

TYPE

nnnn

ANGLE POS.

Upper Arm Spacers

Shims

.

Upper Arm Position

Upper Arm Position

.

Shock Position

Shock Position

Roll Center

+0,5
0

-0,5

+1,5

-1,5

DownStop

Ride Height

Ride Height

80.000

300.000

199

2,5°198

2°
2°

-1,5° 3,5°
3,5°

2,0

2,5

4,0

5,0

1,0

4,5

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

~~~~

37 37
60 60

40 40
62 62

600
Red
3

1,1

600
Red
3

1,1

Std

0°

Wire
2,0

Std Bore Big Bore

~~~~

+

-

-

+

0°

0°

~~~~

Front

Rear

~~~~

~

~

DownStop

A

B

C03 Blank Set-Up Sheet

Front

Rear

.

FRONT

REAR

LEFT RIGHT TYRES LEFT RIGHT

BRAND
SHORE

DIAMETER

OIL
SPRING
PISTON

SHOCK ABSORBERS

ANTI-ROLL BARS

1 ST SPUR GEAR 2 ND

DRIVE TRAIN & D.J. SHAFT

ENGINE

1 ST PINION 2 ND

MIDDLE AXLE PULLEY

25 26 D.J.

TYPE MUFFLER
PLUG NITRO

14 15

19 20

52 53 54 47 48 49

SET-UP SHEET

NAME
DATE
TEMP
TRACK
TRACTION
RESULT BEST LAP

BODY

TYPE

.

CAMBER

TOE / SIDE

WIDHT

GEAR DIFF. OIL

LEFT

RIGHT

CAMBER

TOE /SIDE

WIDHT

LEFT

RIGHT

GEAR DIFF. OIL

ARM POSITION

A B

ACKERMANN INSERTS

10 11 12

GROUND

GROUND

Caster Angle

50

Type 1 Type 2 Type 3

Type 1 Type 2 Type 3

Additional notes

HOLES n

nn

n

Made in Italy

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

TYPE

nnnn

ANGLE POS.

Upper Arm Spacers

Shims

.

Upper Arm Position

Upper Arm Position

.

Shock Position

Shock Position

Roll Center

+0,5
0

-0,5

+1,5

-1,5

DownStop

Ride Height

Ride Height

Std Bore Big Bore

+

-

-

+

0°

0°

Front

Rear

~

~

DownStop

A

B

Parts List

Rif. n° Code

1 2

Cap17051
2 2 Cap17052
3 2

Cap17041
4 2

Cap16019
5

1

Cap18075-X
6 2

Cap17006-X
7

2 Cap17006

Step A

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

Made in Italy

51

Note:
adjust position for minimum offset
and freely front Anti-Roll bar movement

Before

2x

After cut

OPTION KIT

- Front wire & F1 Anti-Roll bar -

cut

16,5

5

6

7

1

2

3

4

3

1

2

6

7

4

5x8x2,5

3x3

3x3

5x8x2,5

Wire

F1 Anti-Roll bar kit

Code Cap18012

0,8 Soft
1,0 Medium
1,2 Hard

bar insert
Code Cap18014-X

2,5

2,5

CCCCaaaapppprrrriiiiccccoooorrrrnnnn RRRRCCCC

- Notes -

Made in Italy

52