Visit www.capressoblog.com
for fun and delicious milk frother recipes
600W / 120Vac / 60Hz
Read all instructions before operating the appliance
Model #207
Patented Frothing Technology
Page 2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
• Read all instructions before operating the appliance.
• After having the packaging removed, check that the appliance is intact. If in
doubt do not use the appliance and contact your sales agent.
• The parts of the packaging, plastic bags etc. must not be left within the reach
of children as they are potential sources of danger.
• DO NOT touch hot surfaces. Use handles or knobs.
• To protect against fire, electric shock and personal injury do not immerse cord,
plugs, or appliance in water or other liquid.
• Never immerse the base in water or any other liquid for cleaning.
• The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
• DO NOT operate any appliance with a damaged cord or plug or if the appliance
has been damaged in any manner. Return the appliance to an authorized
service facility for examination, repair or adjustment.
• DO NOT operate the appliance if the pitcher shows any signs of cracks or
pitcher has a loose or weakened handle.
• The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or personal injury.
• DO NOT use outdoors.
• DO NOT let cord hang over edge of table or counter, or touch hot surfaces.
• DO NOT place on or near a hot gas or electric burner, or in a heated oven.
• Always attach plug to appliance first, then plug cord into the wall outlet.
• To disconnect, turn the power switch off, then remove plug from wall outlet.
• DO NOT use appliance for other than intended use.
• Use extreme caution when disposing hot steam.
• The milk pitcher is not suited for microwave use.
• Only the supplied milk pitcher can be placed on heating platform of the base.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
2.
Page 3
SPECIAL CORD SET INSTRUCTIONS
Regarding your Cord Set:
A. A short power-supply cord (or detachable power-supply cord) is provided to
reduce risks resulting from becoming entangled in or tripping over a longer
cord.
B. Longer detachable power-supply cords or extension cords are available and
may be used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used, (1) the
marked electrical rating of the detachable power-supply cord or extension
cord should be at least as great as the electrical rating of the appliance,
(2) if the appliance is of the grounded type, the extension cord should be a
grounding type 3-wire cord, and (3) the longer cord should be arranged so
that it will not drape over the counter top or table top where it can be pulled
on by children or tripped over.
Notice: This appliance has a 3-prong grounded plug. To reduce the risk of
electrical shock, this plug will fit in an outlet only one way. If the plug does
not fit in the outlet, contact a qualified electrician. DO NOT modify the plug in
any way.
CAUTION:
This appliance is for household use. Any servicing other than cleaning and user
maintenance should be performed by an authorized service representative.
• Do not immerse base in water or try to disassemble.
• To reduce the risk of fire or electric shock, do not disassemble the base.
No user serviceable parts inside.
• Repair should be done by authorized service personnel only.
• Check voltage to be sure that the voltage indicated on the name plate agrees
with your voltage.
• Keep your hands and the cord away from hot parts of the appliance during
operation.
• Never clean with scouring powders or hard implements.
WELCOME AND THANK YOU
Thank you for choosing the Capresso froth Control. This compact and space
saving item froths and heats your milk completely and automatically. It is easy to
use, easy to clean. Use it for hot chocolate, frothed milk and iced cappuccinos.
Please read all of the instructions in this booklet before operating your new
machine. Understanding and complying with these instructions is essential to
ensure that the machine is utilized without risk and to ensure safety during
operation and maintenance.
3.
Page 4
HOW TO REACH CAPRESSO
Should you require further information or if particular problems occur that are
not covered in this manual, please
• CALL our toll free HELP LINE: 1-800-767-3554 Monday -Thursday 8AM to 9PM,
Friday 8AM to 8PM and Saturday 9AM to 5PM Eastern Standard Time.
• FAX us at 1-201-767-9684
• E-MAIL us at contact@capresso.com
• VISIT our website at www.capresso.com
Lid
Fig. 1
Frothing Disk
Milk Pitcher
Fill Markings
––––, MAX, MIN
Base
Selector Dial
Disk Storage
Fig. 1a
Frothing Disk Heating Disk
4.
Page 5
Using the froth Control
The froth Control Automatic Milk Frother & Hot Chocolate Maker comes
equipped with a milk pitcher with lid, two frothing disks, one heating disk and
the base unit. One of the disks is installed inside the milk pitcher. The other disk
and the heating disk are stored underneath the base of the appliance.
Before First Use
Clean the milk pitcher and the disks under running warm water. Make sure the
underside of the milk pitcher is completely dry.
CAUTION:
Maximum Capacity - FROTHING: never fill more than 10 oz.
(see MAX marking inside milk pitcher)
Maximum Capacity - HEATING: never fill more than 14 oz.
(see "––––" marking inside milk pitcher)
Using the Frothing Disk
Never fill more than 10 oz. of milk or chocolate milk
into the milk pitcher ("MAX" marking); otherwise, hot
milk could spill over the milk pitcher onto the heating
platform. This may damage the interior parts of the
machine.
Note: For the CHOC setting, you may use the frothing
disk with a minimum of 8 oz. of milk and a maximum
of 14 oz. of milk.
Frothing Disk
Using the Heating Disk:
Never fill more than 14 oz. of milk or chocolate milk into
the milk pitcher ("––––" marking).
5.
Heating Disk
Page 6
A B C
D E F
Using the Selector Dial
The selector dial (F) will control the speed of the disk in the pitcher while the
frothing or heating disk will control the milk texture of the frothed or heated
milk. There is no right or wrong way to use the frothing or heating disks
combined with the different settings on the selector dial. The below
chart is a helpful guide, but individual results will vary depending on the
type of milk used and different ingredients that are added during the
frothing cycle. It is highly recommended to experiment with the different
setting and disk combinations, to create your own delicious recipes.
Frothing Disk
Heating Disk
(COLD) FROTH(HOT) FROTH(HOT) FLAT(HOT) CHOC
Cold milk with
thick, velvety
froth
Use the frothing
disk for best
results
Heated milk
with maximum
froth, perfect
for cappuccino
Heated milk, no
froth, perfect
for lattes and
steamers
6.
Heated milk
with some
froth, perfect
for flat white
Heated milk, no
froth, perfect
for lattes and
steamers
Heated milk
perfect for hot
chocolate
Use the frothing
disk for best
results
Page 7
Hot Frothing and Heating Milk
Perfect for hot beverages such as cappuccinos, lattes, hot chocolate, flat whites
and milk steamers.
1. Plug in appliance.
2. Remove lid from milk pitcher. (A)
3. Place one of the frothing disks or the heating disk into the bottom of the milk
pitcher. Ensure the disk is completely snapped in. (B)
4. Make sure underside of the milk pitcher is dry.
5. Pour fresh cold milk into the milk pitcher (C) and replace lid. (D)
6. Place pitcher on heating platform. (E)
7. For frothing and heating milk turn the selector dial (F) to the (HOT) FROTH or
FLAT icon. When the (HOT) FROTH icon is selected the disk will rotate at
a high rate of speed. When the FLAT icon is used the disk will spin at a
medium rate of speed. Depending on which disk is used, this will help control
the final texture of the milk once the cycle is complete. Selecting the frothing
disk with the (HOT) FROTH setting will maximize the froth produced while
selecting the heating disk with the FLAT option will give almost no froth but
will heat/steam the milk.
8. Press the center of the selector dial and the frothing/heating action starts
automatically. The dial will illuminate blue and a short beep will indicate that
the cycle has begun.
9. When the milk has reached the maximum temperature, the appliance will
automatically shut off. The indicator light turns off and the frothing action
stops. A short beep will indicate that the end of the cycle has been reached.
The cycle can always be stopped manually by pressing the center of the
selector dial or lifting the pitcher from the base.
CAUTION: The milk pitcher is now very warm; the bottom of the pitcher is
hot. Only place the milk pitcher on a heat resistant surface.
10. Pour the warm milk into your cup and spoon the froth on top.
11. Always unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the appliance.
Cold Frothing and Mixing Milk
Good for cold beverages such as iced cappuccinos, iced fruit lattes, cold malts
and mixing chocolate milk. Follow steps 1 through 6 above in “Hot Frothing and
Heating Milk.”
Note: For the best cold frothing or cold mixing results, it is recommended
to use the frothing disk.
1. For cold frothing or cold mixing (incorporating chocolate syrup into milk, mixing
malt powder, etc.) turn the selector dial (F) to the (COLD) FROTH setting.
2. Press the center of the selector dial and the frothing/mixing action starts
automatically. The dial will illuminate blue and a short beep will indicate that
the cycle has begun.
3. Once the frothing disk starts spinning, you may add any ingredients like
chocolate syrup, malt powder, etc.
7.
Page 8
4. After a few minutes, the appliance will automatically shut off. The indicator
light turns off and frothing stops. A short beep will indicate that the end of the
cycle has been reached. The cycle can always be stopped manually by
pressing the center of the selector dial or lifting the pitcher from the base.
5. Pour milk into cup and spoon froth on top.
6. Always unplug from outlet when not in use and before cleaning.
Making Hot Chocolate
The froth Control features a special hot chocolate function that allows chocolate
chunks or chocolate chips to be added directly to the pitcher. The frothing disk
will rotate slowly, allowing the chocolate to gently mix and heat. You may also
add grated chocolate, chocolate syrup or powdered hot chocolate mix
directly to the milk pitcher. Follow steps 1 through 6 above in “Hot Frothing and
Heating Milk.”
Note: For the best hot chocolate results, it is recommended to use the
frothing disk. A minimum of 8 oz. of milk should be used, otherwise the
milk may burn. A maximum of 14 oz. may be used with the CHOC setting.
1. For hot chocolate turn the selector dial (F) to the CHOC setting.
2. Press the center of the selector dial and the frothing/heating action starts
automatically. The dial will illuminate blue and a short beep will indicate that
the cycle has begun.
3. After a few minutes of heating the illuminated dial will start to blink, and a series
of short beeps will indicate that it is time to add the chocolate into the milk
pitcher.
Note: Once the illuminated dial starts to blink, it will continue blinking
for approximately one minute. Once the light becomes solid, stop
adding chocolate and replace the lid. This will help to ensure that the
chocolate melts completely into the milk before the end of the cycle.
4. Remove the lid from the pitcher and gradually add small chunks of chocolate,
chocolate chips, grated chocolate or powdered hot chocolate mix into the
pitcher. For the best results, add the chocolate slowly by dropping it in small
amounts along the edge of the milk pitcher, away from the rotating disk. It is
not recommended to add more than 150 grams (5 oz.) of chocolate or
powdered hot chocolate mix to the pitcher for one cycle.
Note: If chocolate chunks are left in pitcher after the cycle stops you may
need to use smaller pieces. For best results, try to add all of the chocolate
while the light is blinking, otherwise the chocolate may not have time to fully
melt into the milk.
5. After a few minutes, the appliance will automatically shut off. The indicator
light turns off and the mixing action stops. A short beep will indicate that the
end of the cycle has been reached. The cycle can always be stopped manually
by pressing the center of the selector dial or lifting the pitcher from the base.
6. Pour hot chocolate into cup and enjoy!
7. Always unplug from outlet when not in use and before cleaning.
8.
Page 9
Tips for using the froth Control:
• When adding extra ingredients such as chocolate, smaller pieces will melt
more easily than larger pieces. “Chocolate chips” commonly found in the
baking section of most supermarkets work well.
• Always add extra ingredients along the edge of the pitcher, away from the
rotating disk.
• Always add extra ingredients gradually to help avoid interrupting the cycle.
• It is best to used shaved or grated chocolate when using the (HOT) FROTH
setting, as the smaller pieces are less likely to become stuck in the frothing disk
as it rotates at a higher rate of speed. Use the CHOC setting when adding
larger ingredients like chocolate chunks or chocolate chips.
• If the frothing disk becomes stuck and makes a loud noise, press the center
of the selector dial to stop the cycle. Remove the lid and use a small spoon
to gently mix the ingredients. Press the center of the selector dial to restart the
cycle.
Please note:
• When you remove the milk pitcher from the appliance during operation, the
appliance will automatically shut off. When replacing the pitcher, you need to
press the center of the selector dial to start the cycle again.
• If the heating plate or the bottom of the milk pitcher is still hot, the appliance
may not turn on. In this case, remove the milk pitcher. Cool it down by running
the bottom of the pitcher under cold water. Make sure the bottom of the
pitcher is dry and start over.
CAUTION: Do not place the milk pitcher in the microwave or on any other
heating surface.
Types of Milk
All kinds of milk can be used with this appliance (Whole, 2%, 1%, skim, soy milk,
almond milk, rice milk, etc.) Skim milk will produce the thickest, most stable froth.
Soy milk will produce froth with somewhat larger bubbles, but the froth is not as
stable. Always use milk that is as fresh as possible, to achieve the best results.
Cleaning
1. Unplug the appliance and let it cool down.
2. Remove the frothing disk or the heating disk from the milk pitcher. Clean
under running warm water.
3. The milk pitcher and lid are dishwasher safe (top-rack).
4. Wipe the heating plate with a moist cloth.
5. Discoloration of the heating plate may occur if milk spills onto the heating
plate. Scrub lightly with baking soda.
Frothing / Heating Disk Storage
One disk can be kept inside the milk pitcher. The two other disks can be stored
underneath the base of the appliance.
Additional Milk Pitcher and Disks
Order an additional milk pitcher or disks by calling Customer Service at:
1-800-767-3554 or by visiting www.capresso.com.
9.
Page 10
Recipes
Orange Crème Latte
2 servings
• 8-oz low fat milk
• 1-2 tsp vanilla syrup
• 8-oz orange juice
• shaved ice for serving
Insert the frothing disk, add milk and vanilla syrup to frothing pitcher and choose
the (COLD) FROTH setting. Start the cycle by pressing the center of the selector
dial. Wait for the froth Control to automatically shut off. Place shaved ice into the
glasses and fill half way with orange juice. Pour frothed milk on top and stir.
• 3 black tea bags or 3 heaping teaspoons of loose black tea
• 10-oz milk
• 2 tbsp dark brown sugar
Place first five spice ingredients into a heat safe pitcher. Pour three cups of boiling
water into pitcher and let steep for fifteen minutes. Add three tea bags to water
and continue to steep for five more minutes. While tea is steeping prepare
frothed milk. Insert the frothing disk, add milk to pitcher and choose the (HOT)
FROTH setting. Start the cycle by pressing the center of the dial. After three
minutes, remove lid and add brown sugar* to the frothing pitcher. Replace the lid
and wait for the froth Control to automatically shut off. Strain spices and tea
bags from pitcher and pour tea into cups. Top each cup with frothed milk.
*Be sure to break up any lumps in the brown sugar before adding to the pitcher.
Peanut Butter Hot Chocolate
1 serving
• 10-oz milk
• 2-oz semisweet or bittersweet chocolate chips
• 2-oz peanut butter chips (found in the baking section of most supermarkets)
Insert the frothing disk, add milk to frothing pitcher and choose the CHOC
setting. Start the cycle by pressing the center of the selector dial. After a few
minutes the illuminated light around the selector dial will start to blink indicating
that it is time to add the chocolate and peanut butter chips. Remove the lid and
add the chips gradually along the edge of the pitcher, away from the rotating disk.
Make sure to add all of the chocolate and peanut butter chips before the illuminated
light stops blinking. Replace lid and wait for the froth Control to automatically
shut off. Pour into mugs and enjoy!
10.
Page 11
Deluxe Caramel Latte
2 Servings
• 14-oz milk
• 2 shots of espresso or 4-6 oz of strong brewed coffee
• caramel sauce
• whipped cream
Prepare 2 shots of espresso or 4-6 oz of coffee and set aside. Insert the heating
disk add milk to the frothing pitcher and choose the FLAT setting. Start the cycle
by pressing the center of the selector dial. While the milk is heating coat the
inside of two cups with the caramel sauce and divide the prepared coffee evenly
between the two cups. Once the milk is finished heating, add 7-oz to each cup
and top with whipped cream and more caramel sauce.
Tip: For a latte with slightly more froth, replace the heating disk with the frothing
disk; follow the MAX guideline for frothing capacity.
Visit www.capressoblog.com for fun and delicious milk frother recipes.
LIMITED WARRANTY
This warranty covers your Capresso machine Model #207. This warranty is in
effect for one year from the date of the first consumer purchase. This warranty
covers all defects in materials or workmanship (parts and labor). Capresso will
repair or replace your machine within one year from the date of the first consumer
purchase.
The warranty does not cover:
• Any machine not distributed by Capresso.
• Any machine not purchased from an Authorized Capresso Dealer.
• Commercial use of the machine.
• Damage caused by accident, abuse, negligence, misuse, improper operation
or failure to follow instructions contained in this manual.
• Any service or alteration performed by an unauthorized person, company or
association.
• Any used machines bought at auctions and unauthorized websites.
Other limitations and exclusions:
Any implied warranties including fitness for use and merchantability are limited in
duration to the period of the express warranty set forth above and no person is
authorized to assume for JURA any other liability in connection with the sale of
the machine. JURA expressly disclaims liability for incidental and consequential
damages caused by the machine. The terms "incidental damages" refers to the
loss of the original purchaser’s time, loss of the use of the machine or other
costs relating to the care and custody of the machine. The term "consequential
damages" refers to the cost of repairing or replacing other property which is
damaged when this machine does not work properly. The remedies provided
under this warranty are exclusive and in lieu of all others. This warranty gives
you specific legal rights, and you may also have other rights which vary from
state to state.
11.
Page 12
JURA Inc.
20 Craig Road, Montvale, NJ 07645
Tel: 800-767-3554
Fax: 201-767-9684
contact@capresso.com
www.capresso.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.