Caple WMI3000, WMI3005 Instruction Manual

Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk

Integrated Washing Machine

instruction manual

WMI3000 / WMI3005

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

2

CONTENTS

CONTENTS

Safety Warnings 3

Overview of Washing Machine 9

Installation 10

Operation 15

Control panel 18

Table of washing procedures 24

Cleaning and Maintenance 25

Troubleshooting 31

Care symbols 32

Product specifications 34

Product Fiches 36

Built-In Installation 38

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

3

WARNINGS

- If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.

- The new hose-sets supplied with the appliance are to be
used and old hose-sets should not be reused.

- This washing machine is for indoor use only.

- The openings must not be obstructed by a carpet.

- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge, if they have been given supervision or
instruction concerning use of the appliance in a safeway
and understand the hazards involved.

- Children shall not play with the appliance.

- Cleaning and user maintenance shall not be made by
children without supervision.

- This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

4

- Children should be supervised to ensure that they do not
play with the appliance.

- Pull out its plug from the power socket before cleaning
or maintenance.

- Make sure that all pockets are emptied.

- Sharp and rigid items such as coins, nails, screws or
stone etc may cause serious damages to this machine.

- Pull out its plug and cut off water supply after the
operation.

- Please check whether the water inside the drum has
been drained before opening its door. Please do not
open the door if there is any water visible.

- Pets and kids may climb into the machine. Check the
machine before every operation.

- Take care that power voltage and frequency shall be
identical to those of washing machine.

- Do not use any socket with rated current less than that
of washing machine.

- Never pull out power plug with wet hands.

- To ensure your safety, the power cord plug must be
inserted into an earthed three-pole socket. Check
carefully and make sure that your socket is properly and
reliably earthed.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

5

- Children of less than 3 years old should be kept away
unless continuously supervised.

- Children should be supervised to ensure that they do not
play with the machine.

- Packing materials may be dangerous to children. Please
keep all packing materials (plastic bags, foams etc) far
away.

- Washing machines shall not be installed in bathrooms
or wet rooms as well as in the rooms with explosive or
caustic gases.

- The water and electrical connections must be connected
by a qualified engineer in accordance with the
manufacturer’s instructions and local safety regulations.

- Before operating this machine, all packages and
transport bolts must be removed. Otherwise the washing
machine may be seriously damaged while washing the
clothes.

- This product is not designed for commercial use, it is a
household appliance only. It is not intended to be used
in:

- Staff kitchen areas in shops, offices and other working
environments.

- Bed and breakfast type environments.

- By clients in hotels, motels and other residential
type environments.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

6

- Before using the machine for the first time, the washing
machine shall be operated in one round of the whole
procedures without the clothes inside.

- Your washing machine is only for home use and is only
designed for the textiles suitable for machine washing.

- Flammable and explosive or toxic solvents are forbidden.
Gasoline and alcohol etc shall not be used as detergents.
Please only select the detergents suitable for machine
washing.

- Do not wash carpets in this washing machine

- Be careful of burning when washing machine drains hot
washing water.

- Never refill the water by hand during washing.

- After the program is completed, Please wait for two
minutes before opening the door.

- Please remember to disconnect water and power supply
immediately after the clothes are washed.

- Do not climb up and sit on top cover of the machine.

- Do not lean against machine door.

- Please do not close the door with excessive force. If it
is found difficult to close the door, please check if the
excessive clothes are put in or distributed well.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

7

- Transport bolts shall be reinstalled to the machine by a
competent person.

- The accumulated water shall be drained out of the
machine.

- Handle the machine carefully. Never hold each protruded
part on the machine while lifting. Machine door cannot
be used as the handle during the conveyance.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

8

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice. This appliance is marked according to the European directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The symbol
on the product indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. Disposal must be carried out in accordance with
local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this
product, please contact your local council, your household waste disposal service or
the retailer where you purchased the product

CE DECLARATIONS OF CONFORMITY

This appliance has been manufactured to the strictest standards and complies
with all applicable legislation, Low Voltage Directive (LVD) and Electromagnetic
Compatibility (EMC).

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

9

OVERVIEW OF WASHING MACHINE

Overview of Washing Machine

Component

Door

Detergent Drawer

Control Panel

Power Plug

Outlet Hose

Overview of Washing Machine

Component

Door

Detergent Drawer

Control Panel

Power Plug

Outlet Hose

Detergent Box

Overview of Washing Machine

Inlet pipe

Transport

plughole

Component

Accessories

Door

Detergent Drawer

Control Panel

Power Plug

Outlet Hose

Detergent Box

Component

Accessories

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

10

INSTALLATION

Unpacking the washing machine

Unpack your washing machine and check if there is any damage during the
transportation. Also make sure that all the items (as shown in Page 9) in the
attached bag are received. If there is any damage to the washing machine during
the transportation, or any item is missing, please contact your retailer immediately.

Dispose of the packing materials

The packing materials of this machine may be dangerous to children. Please dispose
of them properly. Please dispose the related packing materials according to the
relevant local regulations. Please do no throw the packing materials away together
with the other daily living disposals.

Remove transport bolts

Before using this washing machine, transport bolts
must be removed from the backside of this machine.
Please take the following steps to remove the bolts:

1. Loosen all bolts with spanner and then
remove them.

2. Fill the holes with transport hole plugs.

3. Keep the transport bolts stored away safely for future use.

Installation

Connect the inlet pipe as indicated in the figure.

3.Ensure the positioning status of washing machine. Loosen the lock nut with spanner

and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.

4.After being locked properly, press four corners again to make sure that they have been adjusted

suitably. If it is still unstable, repeat Steps 2 and 3 until stable.

5.Put a solid cylinder horizontally on the top cover of the washing machine from in

the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.

Connect inlet pipe

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

11

Select the location

Before installing the washing machine, the location characterised as follows shall
be selected:

- Rigid, dry, and level surface (if not level, please make it level with reference to the
following figure “Adjust Legs”)

- Avoid direct sunlight

- Sufficient ventilation

- Room temperature is above 0 C

- Keep far away from heat resources.

- Make sure that the washing machine does not stand on the power cord.

- Do not install the washing machine on the carpet floor.

Adjust Legs

1. When positioning the washing machine, please
first check if the legs are closely attached to the
washing machine. If not, please turn them to their
original positions with hand or spanner and tighten
the nuts with spanner.

2. After positioning the washing machine, press
four corners on top cover of washing machine in
sequence. If the washing machine is not stable
when being pressed, this leg shall be adjusted.

3. Ensure the positioning status of washing machine. Loosen the lock nut with
spanner and turn the leg with hand until it closely contacts with the floor. Press
the leg with one hand and fasten the nut closely to the washing machine with
the other hand.

4. After being locked properly, press four corners again to make sure that they have
been adjusted suitably. If it is still unstable, repeat Steps 2 and 3 until stable.

5. Put a solid cylinder horizontally on the top cover of the washing machine from in
the left, right, front and back directions. If the cylinder keeps stable, the washing
machine is positioned level. If it rolls, the washing machine is not level. The
rolling direction is the direction of lower ground surface. Then, the two legs in
this direction shall be raised at the same time until the washing machine is level.
Steps 1~3 are repeated to make the bottom legs closely against the ground and
the nuts shall be locked tightly.

Installation

Connect the inlet pipe as indicated in the figure.

Install inlet pipe

1.Connect the elbow to tap and fasten it
clockwise.

2.Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.

Notes: after connection, if there is any leakage
with hose, then repeat the steps to connect inlet
pipe. The most common type of tap shall be
used to supply water. If tap is square or too big, then
standard tap shall be changed.

Ho

le plug
This Hole plug is used to block the hole on the back
of the washing machinet.

Place outlet hose
There are two ways to place the end of outlet hose:

1.Put it inside the sink bowl as shown

3.Ensure the positioning status of washing machine. Loosen the lock nut with spanner

and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.

4.After being locked properly, press four corners again to make sure that they have been adjusted

suitably. If it is still unstable, repeat Steps 2 and 3 until stable.

5.Put a solid cylinder horizontally on the top cover of the washing machine from in

the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.

Connect inlet pipe

Instruction manual WMi3000 / WMi300512

Connect inlet pipe

Connect the inlet pipe as indicated in the figure.

Install inlet pipe

1. Connect the elbow to tap and fasten it clockwise.

2. Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.

NOTES: after connection, if there is any leakage with
hose, then repeat the steps to connect inlet pipe. The
most common type of tap shall be used to supply
water. If tap is square or too big, then standard tap
shall be changed.

Hole plug

This Hole plug is used to block the hole on the back of
the washing machinet.

Place outlet hose

There are two ways to place the end of outlet hose:

1. Put it inside the sink bowl as shown

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

13

Position outlet hose properly so that the floor will not be damaged by water leakage.

NOTES:

If the machine has outlet hose support, please install it like the following pictures

Installation

1.This machine must be earthed properly. If there is any short circuit, earthing can reduce
the danger of electrical shock.

This machine is equipped with power cord, which includes plug, earthing wire at earthing
terminal.

2.Washing machine shall be operated in a circuit separate from other electrical appliances.
Otherwise, power protector may be tripped or fuse may be burned out.

！

WARNING

Max.100cm

Min.60cm

Min.60cm

Max.100cm

Installation

1.This machine must be earthed properly. If there is any short circuit, earthing can reduce
the danger of electrical shock.

This machine is equipped with power cord, which includes plug, earthing wire at earthing
terminal.

2.Washing machine shall be operated in a circuit separate from other electrical appliances.
Otherwise, power protector may be tripped or fuse may be burned out.

！

WARNING

Min.60cm

Max.100cm

Installation

1.This machine must be earthed properly. If there is any short circuit, earthing can reduce
the danger of electrical shock.

This machine is equipped with power cord, which includes plug, earthing wire at earthing
terminal.

2.Washing machine shall be operated in a circuit separate from other electrical appliances.
Otherwise, power protector may be tripped or fuse may be burned out.

！

WARNING

Min.60cm

Max.100cm

Sink

Hose Retainer

Bind

Max.100cm
Min.60cm

Min.60cm

Max.100cm

Installation

1.This machine must be earthed properly. If there is any short circuit, earthing can reduce
the danger of electrical shock.

This machine is equipped with power cord, which includes plug, earthing wire at earthing
terminal.

2.Washing machine shall be operated in a circuit separate from other electrical appliances.
Otherwise, power protector may be tripped or fuse may be burned out.

！

Max.100cm

Min.60cm

Min.60cm

Max.100cm

Sink

Hose Retainer

Bind

Position outlet hose properly so that the floor will not be damaged by water leakage.
Notes:
If the machine has

outlet hose support, please install it like the following pictures.

It can drain the water up and down, outlet hose shall not be installed at a
height beyond 100cm and its end shall not be immersed in water

When installing outlet hose, fix it
properly with a rope.

Position outlet hose properly so that
the floor will not be damaged by
water leakage.

If outlet hose is too long, do not force
it into washing machine as it will
cause abnormal noises.

2. Connect it to the drain outlet on the sinks waste pipe.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

14

Electrical Connection

- As the maximum current through the unit is 10A when you are using its heating
function, please make sure the power supply system (current, power voltage
and wire) at your home can meet the normal loading requirements of the
electrical appliances.

- Please connect the power to a socket which is correctly installed and
properly earthed.

- Make sure the power voltage at your place is same to that in the machine’s
rating label.

- Power plug must match the socket and cabinet must be properly and
effectively earthed.

- Do not use multi-purpose plug or socket as extension cord.

- Do not connect and pull out plug with wet hand. When connecting and pulling
out the plug, hold the plug tightly and then pull it out. Do not pull power
cord forcibly.

- If power cord is damaged or has any sign of being broken, special power
cord must be selected or purchased from its manufacturer or service center
for replacement.

WARNING

This machine must be earthed properly. If there is any short
circuit, earthing can reduce the danger of electrical shock.

This machine is equipped with power cord, which includes
plug, earthing wire at earthing terminal.

Washing machine shall be operated in a circuit separate
from other electrical appliances. Otherwise, power
protector may be tripped or fuse may be burned out.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

15

OPERATION

Empty all pockets

Foreign objects (e.g. nails, coins, paper, clips etc) can cause damage to garments
and to the components in the machine.

Check the laundry before washing and remove foreign objects.

Sort the laundry

Sort the laundry by colour and care label. Most garments have a textile care label in
the collar or side seam.

Tip: Dark textiles often contain excess dye and should be washed separately several
times before being included in a mixed load. Always wash whites and coloured
separately.

Pre-treat stains

Badly soiled areas, stains etc. should be cleaned as soon as possible, preferably
whilst still fresh. Spillages should be carefully dabbed off using a soft, colour fast
cloth. Do not rub.

Tip: Badly soiled areas can be pretreated with a liquid detergent, stain removers etc.
first, following the manufacturer’s instructions. With particularly stubborn stains ask
your dry cleaner for advice.

Solvent-based cleaners (e.g. benzine) can damage plastic parts. When pre-treating
garments, make sure that any plastic parts (e.g. buttons) are protected from
cleaning agent.

Chemical (solvent-based) cleaning agents can cause severe damage to the washing
machine. Do not use solvent-based cleaning agents in the machine.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

16

General Tips

- Curtains: Remove lead weights first or place in a laundry bag

- Undewiring and collar stiffeners: Any loose wiring in bras, shirt collar stiffeners,
etc. should be removed or sewn in.

- Close any zips, attach Velcro fasteners fasten hooks and eyes etc. before washing.

- Fasten duvet covers, pillow cases etc. to prevent small items from being rolled up
inside them.

Do not wash any items in this washing machine which are specified by the
manufacture as not washable on the care label (

symbol).

Confirm the washing capacity:

Do not load excessive washing; otherwise it may affect the washing performance.
Please confirm the maximum washing quantity according to the following table.

Fiber Type Maximum loading Capacity

WMI3000 - 6.0kg WMI3005 - 8.0kg

Cotton 6.0kg 8.0kg

Synthetics 3.0kg 4.0kg

Wool 2.0kg 2.0kg

Delicate 2.5kg 2.5kg

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

17

QUICK START

1. Install the washing machine

2. Open the door and Load the laundry

3. Measure out the detergent

4. Close the door

5. Put down (hang up) the drain pipe (if not connected to sink plumbing)

6. Turn on the water tap (if not connected to mains water supply)

7. Plug the power supply

8. Press the On/Off

9. Select the desired programme

10. Press the [start/pause]

After washing notes:

- After washing, the washing machine will make a sound to signify the
end of a cycle

- Close the water tap;

- Press the On/Off and pull out the power plug.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

18

CONTROL PANEL

Programme selector

For the convenience of
users to easily select the
required programme.

LED Display

Display the Pre wash /
Extra Rinse/Remain time
/Door lock/Child lock
running state.

Start/Pause

Press the button to start
or pause the wash cycle.

On/Off

Press once to turn the
washing machine on,
press again to turn the
washing machine off.

Function setting

Press the button
repeatedly to set the
Pre Wash, Extra Rinse
function.

Speed

Press the button
repeatedly to
regulate the speed.

Delay

It is used for delay
wash (0-24h).
The delaying time
means the wash
will begin in (xx)
h later..

Temp.

Press the button
to regulate the
temperature

Notes:

- The Control panel line chart is for reference only, Please refer to real product

as standard.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

19

Using for the first time

Before using for the first time, the washing machine shall be operated in one round
of the whole procedures without clothes in as follows:

1.Connect power source and water.

2.Put a little detergent into the box and close it.

3.Press the button “On/Off”.

4.Press the button “Start/Pause”.

The drawer is separated as follows:

I: Pre-detergent or washing powder.

II: Main detergent

Washing additives,such as fabric softener.

Put detergent into washing machine.

1.Pull out the drawer.

2.Fill pre-detergent into Case I (when necessary).

3.Fill softener into Case

.

4.Fill detergent into Case II (when necessary).

Notes:

option1: detergent (powder)

option2: (liquid)

Please choose suitable type of detergent for the various washing temperature to get
the best washing effect with less water and energy consumption.

Operation

℃- Cotton 60/40/20

First, turn the rotary switch to select the corresponding programme according to the types
of articles.

Second, select the appropriate temperature according to the dirtiness. Generally, the higher the
temperature is, the more the power is consumed.

Lastly, select the proper revolution speed. The higher the revolution speed is, the drier the
articles are spun, but higher the noises will also be.

The surfaces of delicate articles will have wrinkles and the working life of the

washing machine will shorten.

PLEASE NOTE: to protect the clothes, the lower revolution speed shall be selected for delicate textiles.
The main washing procedures depend on the types of the clothes to be washed as follows:

-

Cotton Intensive
You can select this programme to wash every day clothes. The washing period is quite long with
intensive washing. It is recommended to wash the daily cotton articles such as: bed sheets, quilt
covers, pillowcases, gowns, underwear, towles etc.

Ⅰ

Ⅱ

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

20

START UP WASHING MACHINE

Connect the power. Check if water pipes are connected properly, and turn on
water mains/tap completely. Put in the clothes to be washed and fill the detergent
and softener. Then press the “On/ Off” button, select the proper procedures and
functions and press the “Start/Pause” button.

SELECT THE PROGRAMME

The suitable washing programme should be selected according to the types,
quantities, and condition of the clothes to be washed in combination with the
following washing temperature table.

90ºC Heavily soiled, pure white cotton or linen (for example:

table cloths, towels, bed sheets/bedding)

60ºC Moderately soiled, coloured cotton and synthetic articles

with certain decolorizing degree (for example: shirts,
pajamas; slightly stained white linen)

40ºC, 30ºC
20ºC, Cold water

Normally soiled articles (for example: synthetic and wool)

First, turn the rotary switch to select the corresponding programme according to
the types of articles.

Second, select the appropriate temperature according to the dirtiness. Generally,
the higher the temperature is, the more the power is consumed.

Lastly, select the proper revolution speed. The higher the revolution speed is, the
drier the articles are spun, but higher the noises will also be.

NOTE: The surfaces of delicate articles will have wrinkles and the working life of
the washing machine will shorten.

NOTE: To protect the clothes, the lower revolution speed shall be selected for
delicate textiles. The main washing procedures depend on the types of the clothes
to be washed as follows:

Cotton Intensive

You can select this programme to wash every day clothes. The washing period is
quite long with intensive washing. It is recommended to wash the daily cotton
articles such as: bed sheets, quilt covers, pillowcases, gowns, underwear, towles etc.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

21

Cotton 60ºC / 40ºC / 20ºC

You can select this programme to wash the every day clothes. The washing period is
quite long with quite strong washing intension. The temperature is default at 60ºC /
40ºC / 20ºC Dependant on which programme is selected.

Express 15º

This programme is suitable for washing few and very lightly soiled clothes in 15
minutes.

Eco

This programme is for a small quantity of lightly soiled items only. The water
temperature is cold.

Baby Care

You can select this programme to wash your baby’s clothes, it can make the baby’s
wear cleaner and make the rinse performance better to protect the baby’s skin.

Sports

You can select this programme to wash sportswear.

Synthetic

You can select this programme to wash the delicate clothes. The programme is
shorter compared with that for cottons and the washing intensity is gentler. It is
recommended to wash synthetic articles, for example: shirts, coats, blending. As
for curtains and laced textiles, the procedure “Synthetic ” shall be selected. While
washing the knitting textiles, detergent quantity shall be reduced due to its loose
string construction and the easy formation of bubbles.

Mix

You can select this programme to wash the tough clothes, that need much more
time and strength. It is used for the daily clothes, cotton, bedsheets, pillowcases,
bathrobes and underwear.

Wool

You can select this programme to wash the wool textiles labeled with “Machine
Wash”. Please select the appropriate washing temperature according to the label
on the articles to be washed. Furthermore, the proper detergent shall be selected
for wool textiles.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

22

Delicate

You can select this programme to wash your delicate clothes. Its washing intensity is
gentler and revolution speed is less compared with the procedure “Synthetic”. It is
recommended for the articles that need to be washed softly.

Drain Only

Separate Drain only Programme

Spin Only

Separate spin only programme. Soap water or rinse water shall be drained out
before spinning.

Rinse & Spin

Separate Rinse & Spin Programme.

My Cycle

Hold the ‘Speed’ button for 3sec. for ‘My cycle’ to memorize a certain programme.
The default ‘My cycle’ programme is ‘Cotton intensive’.

The main function can be selected as follows:
Pre wash

The Pre wash function will perform an extra wash before the main wash.

Extra Rinse

The laundry will undergo an extra rinse once after you have selected it.

Delay

The delay function can be set with this button, the delaying time is 0-24 hr.

Set the delay function:

1.Select a programme;

2.Press the Delay button to choose the time;

3.Press Start/Pause to commence the Delay operation.

Cancel the Delay function :Press the Delay button until the display will be 0H . It
should be pressed before starting the program. If the program already started, press
the On/Off button.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

23

Notes: If there is any break in the power supply while the machine is operating,
a special memory function stores the selected programme and when the power is
restarted, the leftover time continues.

Child Lock

To avoid the washing procedure being interrupted due to the mis operation by
children or by accidental pressing of buttons during the washing procedure, you can
select this function. In this case, all buttons except for the On/Off button will not
work. The washing machine will turn off when the on/off button is pressed. whilst
off, the machine remembers and continues with child lock and the program when
the on/off is pressed again.

Press “Temp.” and “Speed” buttons together for 3 seconds during the running
procedure, the buzzer will beep ,Start/Pause button as well as the rotary switch
are locked. Press the two buttons for 3 seconds together and the buzzer will
beep to release the locking. The child lock will not automatically cancel after the
programmes are completed.

Turning off/on audible alarms

It is possible to deactivate the buzzer on your appliance. After deactivating the
buzzer function, the buzzer will no longer sound until re activated.

After starting the machine, press and hold the “Temp.” button for 3 seconds
and you will hear a beep. The buzzer will be deactivated. To reactivate the buzzer
function, press and hold the “Temp.”button again for 3 seconds.

Warning: After deactivating the buzzer function, all sounds will not be activated
any more.

Bubble Removal Function

Bubble Check Function: Redundant bubbles will occur when there is excessive
detergent, which will affect wash and rinse effects. The procedure will check
automatically and remove any excess bubbles when they are detected

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

24

TABLE OF WASHING PROCEDURES

Before any cleaning or maintenance starts, please do pull out the power plug or disconnect
power and close the tap.

- Solvents are forbidden to avoid damaging the washing machine. Toxic gases are also generated
and may explode.

- Never use water to sprinkle and wash the washing machine.

- It is forbidden that detergents containing PCMX are used to clean the washing machine.

Cleaning and Maintenance of Washing Machine

Proper maintenance on the washing machine can extend its working life. The surface can
be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any
water overflow, use the wet cloth to wipe it off immediately. No sharp items are allowed to
strike the cabinet.

Notes: formic acid and its diluted solvents or equivalent are forbidden.

Clean Internal Drum
The rusts left inside the drum by the metal articles shall be removed immediately with
chlorine-free detergents.
Never use steel wool.

Washing Machine freezing

When the temperature drops below zero and your washing machine gets frozen, you may:

1.Disconnect the power supply for the washing machine.

2.Wash the tap with warm water to loosen inlet pipe.

3.Take down inlet pipe and immerse it in warm water.

4.Pour warm water into washing drum and wait for 10 minutes.

5.Reconnect inlet pipe to the tap and check whether inlet and outlet are working normally.

Notes: when the washing machine is reused, make sure the ambient temperature is above 0 C

Anti-freeze
If your washing machine is located in the room where it can get frozen easily, please drain
the remaining water inside drain pipe and inlet pipe thoroughly.
Remove the remaining water in inlet pipe:

1.Close the tap.

2.Screw off the inlet pipe from tap and put its end into the container.

3.Start up any procedure except single Wash or Drain
procedure. Water will be drained out of inlet pipe if any
for about 40 seconds.

4.Reconnect the inlet pipe to tap.

Remove the remaining water in drain pump

T

o avoid burning, it shall be done after the hot water

Cleaning & Maintenance

Load(kg)

Detergent Box

Procedure

Description

Default Speed

(RPM)

Default Time

(H)

Cotton Intensive

Default Temp.

(℃)

40

Sports

40

Mixed

40

Drain Only

Spin Only

Rinse&Spin

Hand Wash

(Eco)

Cold

Express15'

20

Wool

40

Delicate

30

The energy class is A++(WMI3000 - 6.0kg),A+++(WMI3005 - 8.0kg) Energy test program: Cotton 60/40℃, Speed: the highest speed; Other as the

default.

Half load for 6.0/8.0Kg machine:3.0/4.0Kg.

“Cotton 60/40

℃

” are the “standard Cotton 60/40

℃

” programme and the standard washing programs to which the information in the label

and the fiche relates, and they are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in

terms of combined energy and water consumptions for washing that type of cotton laundry,that the actual water temperature may differ

from the declared cycle temperature.

●　Means must ○　Means optional Means not necessary

Notes: The parameters in this table are only for user's reference. The actual parameters maybe different with the parameters in above mentioned table.

Synthetic

40

Cotton 60℃60Cotton 40℃

40

Cold

Baby care

Delay

60

Softener

Case

×

8.0

8.0

4.0

8.0

8.0

8.0

2.0

8.0

2.0

2.5

4.0

8.0

8.0

2.0

8.0

6.0

6.0

3.0

6.0

6.0

7.0

2.0

6.0

2.0

2.5

3.0

6.0

6.0

2.0

6.0

1400

800

800

1000

1000

1000

800

400

600

800

1200

1200

800

1000

1200

Prewash

Extra rinse

1200

800

800

1000

1000

1000

800

400

600

800

1000

1000

800

1000

1000

2:40

1200/1400

1:19

1:13

0:01

0:14

0:31

1:00

1:13

1:06

1:00

1:40

1:47

1:32

0:15

1:39

Cotton 20℃

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

25

The energy class is A++(WMI3000 - 6.0kg), A+++(WMI3005 - 8.0kg) Energy test
program: Cotton 60/40

o

C, Speed: the highest speed; Other as the default. Half load

for 6.0/8.0Kg machine:3.0/4.0Kg.

“Cotton 60/40

o

C” are the “standard Cotton 60/40oC” programme and the
standard washing programs to which the information in the label and the fiche
relates, and they are suitable to clean normally soiled cotton laundry and that
they are the most efficient programmes in terms of combined energy and water
consumptions for washing that type of cotton laundry,that the actual water
temperature may differ from the declared cycle temperature. Means must

Means optional X Means not necessary Notes: The parameters in this table

are only for user’s reference. The actual parameters maybe different with the
parameters in above mentioned table.

CLEANING & MAINTENANCE

Before any cleaning or maintenance starts, please do pull out the power plug or
disconnect power and close the tap.

WARNING

- Solvents are forbidden to avoid damaging the washing machine.
Toxic gases are also generated and may explode.

- Never use water to sprinkle and wash the washing machine.

- It is forbidden that detergents containing PCMX are used to

clean the washing machine.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

26

CLEANING AND MAINTENANCE

Proper maintenance on the washing machine can extend its working life. The
surface can be cleaned with diluted non-abrasive neutral detergents when
necessary. If there is any water overflow, use the wet cloth to wipe it off
immediately. No sharp items are allowed to strike the cabinet.

NOTE: formic acid and its diluted solvents or equivalent are forbidden.

Clean Internal Drum

The rusts left inside the drum by the metal articles shall be removed immediately
with chlorine-free detergents.

Never use steel wool.

Washing Machine freezing

When the temperature drops below zero and your washing machine gets frozen,
you may:

1. Disconnect the power supply for the washing machine.

2. Wash the tap with warm water to loosen inlet pipe.

3. Take down inlet pipe and immerse it in warm water.

4. Pour warm water into washing drum and wait for 10 minutes.

5. Reconnect inlet pipe to the tap and check whether inlet and outlet are
working normally.

NOTE: when the washing machine is reused, make sure the ambient temperature is
above 0

o

C

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

27

Anti-freeze

If your washing machine is located in the room where it can get frozen easily, please
drain the remaining water inside drain pipe and inlet pipe thoroughly.

Remove the remaining water in inlet pipe:

1. Close the tap.

2. Screw off the inlet pipe from tap and put its
end into the container.

3. Start up any procedure except single Wash or Drain
procedure. Water will be drained out of inlet pipe if
any for about 40 seconds.

4. Reconnect the inlet pipe to tap.

Remove the remaining water in drain pump

WARNING

- To avoid burning, it shall be done after the hot water inside the
machine cools down.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

28

Clean detergent box and grooves

Clean detergent drawer and grooves

1. Press down the arrow location on softener cover
inside the drawer.

2. Lift the clip up and take out softener cover and
wash all grooves with water.

3. Restore the softener cover and push the drawer
into position.

Clean inlet filter

Inlet filter must be cleaned if there is not any or
insufficient water in when the tap is opened.

Clean the tap filter:

1. Close the tap.

2. Select any procedure except “Wash” or “Drain”
procedure.

3. Press the button “Start/Pause” and keep the
procedure running for about 40 seconds.

4. Remove the inlet pipe from the tap.

5. Use water to wash the filter.

6. Reconnect the inlet pipe.

Washing the filter in washing machine:

1. Screw off the inlet pipe from the backside of the machine.

2. Pull out the filter with long nose pliers and reinstall it back after
being washed.

3. Reconnect the inlet pipe.

4. Open the tap and make sure there is no water leakage.

5. Close the tap.

Cleaning & Maintenance

Pull out the power plug to avoid electrical shock before washing.
After using the washing machine, pull out the power cord and close the door tightly to avoid
potential harm.

Remove foreign matters
Drain Pump Filter:

Drain pump filter can filter small foreign matters from the washings.
Clean the filter periodically to ensure the normal operation of the washing machine

.

According to the soil level within the cycles and the frequency of the cycles, you have to inspect

and clean the filter regularly.
The pump should be inspected if the machine does not empty and/or spin;
The machine makes an unusual noise during draining due to objects such as safety pins, coins
etc. blocking the pump.
The Service_panel proceed as follows:

2.Turn the filter down as
shown with the figure and
take out sundries matters.

1.After the power is dis-
connected, pull out the
Dam-Board.

3.Reinstall each part back
after sundries matters are
removed.

Cleaning & Maintenance

Pull out the power plug to avoid electrical shock before washing.
After using the washing machine, pull out the power cord and close the door tightly to avoid
potential harm.

Remove foreign matters
Drain Pump Filter:

Drain pump filter can filter small foreign matters from the washings.
Clean the filter periodically to ensure the normal operation of the washing machine

.

According to the soil level within the cycles and the frequency of the cycles, you have to inspect

and clean the filter regularly.
The pump should be inspected if the machine does not empty and/or spin;
The machine makes an unusual noise during draining due to objects such as safety pins, coins
etc. blocking the pump.
The Service_panel proceed as follows:

Warning!
When the appliance is in use and depending on the programme selected there can be hot water in

pump. Never remove the pump cover during a wash cycle, always wait until the appliance

the cycle, and is empty. When replacing the cover, ensure it is securely tightend

.

2.Turn the filter down as
shown with the figure and
take out sundries matters.

1.After the power is dis-
connected, pull out the
Dam-Board.

3.Reinstall each part back
after sundries matters are
removed.

Dam-Board

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

29

Cleaning & Maintenance

Pull out the power plug to avoid electrical shock before washing.
After using the washing machine, pull out the power cord and close the door tightly to avoid
potential harm.

Remove foreign matters
Drain Pump Filter:

Drain pump filter can filter small foreign matters from the washings.
Clean the filter periodically to ensure the normal operation of the washing machine

According to the soil level within the cycles and the frequency of the cycles, you have to inspect

and clean the filter regularly.
The pump should be inspected if the machine does not empty and/or spin;
The machine makes an unusual noise during draining due to objects such as safety pins, coins
etc. blocking the pump.
The Service_panel proceed as follows:

Warning!
When the appliance is in use and depending on the programme selected there can be hot water in

pump. Never remove the pump cover during a wash cycle, always wait until the appliance

the cycle, and is empty. When replacing the cover, ensure it is securely tightend

1.After the power is dis-
connected, pull out the
Dam-Board.

Dam-Board

inside the drawer.

all grooves with water.

position.

Clean inlet filter

procedure.

procedure running for about 40 seconds.

machine.

NOTE: Generally, the tap filter is washed first and then the filter in washing
machine will be washed. If only the filter in washing machine is washed, then the
steps 1~3 in cleaning the tap filter shall be repeated.

WARNING

Pull out the power plug to avoid electrical shock before
washing. After using the washing machine, pull out the
power cord and close the door tightly to avoid potential
harm.

Remove foreign matters

Drain Pump Filter:

Drain pump filter can filter small foreign matters from the washings.
Clean the filter periodically to ensure the normal operation of the washing machine.

WARNING

According to the soil level within the cycles and the
frequency of the cycles, you have to inspect and clean
the filter regularly. The pump should be inspected if the
machine does not empty and/or spin; The machine makes
an unusual noise during draining due to objects such as
safety pins, coins etc. blocking the pump.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

30

The Service panel proceed as follows:

Pull out the power plug to avoid electrical shock before washing.
After using the washing machine, pull out the power cord and close the door tightly to avoid
potential harm.

Remove foreign matters
Drain Pump Filter:

Drain pump filter can filter small foreign matters from the washings.
Clean the filter periodically to ensure the normal operation of the washing machine

.

According to the soil level within the cycles and the frequency of the cycles, you have to inspect

and clean the filter regularly.
The pump should be inspected if the machine does not empty and/or spin;
The machine makes an unusual noise during draining due to objects such as safety pins, coins
etc. blocking the pump.
The Service_panel proceed as follows:

2.Turn the filter down as
shown with the figure and
take out sundries matters.

1.After the power is dis-
connected, pull out the
Dam-Board.

3.Reinstall each part back
after sundries matters are
removed.

Dam-Board

1. After the power is
disconnected, pull out
the Dam-Board.

2. Turn the filter down as
shown with the figure
and take out sundries
matters.

3. Reinstall each part
back after sundries
matters are removed.

WARNING

When the appliance is in use and depending on the
programme selected there can be hot water in the pump.
Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is empty.
When replacing the cover, ensure it is securely tightend.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

31

TROUBLESHOOTING

Troubles Reason Solution

Washing machine
cannot start up

Check if the door is closed tightly.
Check if power plug is inserted well.
Check if water supply tap is opened.
Check if button “Start/Pause” is
pressed.
Check if button “On/Off” is pressed

Door cannot be
opened

Machine’s safety protection
design is working.

Disconnect the power.

Heating fault NTC is damaged and heating

pipe is aging.

Can normally wash the clothes.
Only cannot wash with heating.
Shall contact the service center
promptly.

Water leakage The connection between inlet

pipe or outlet hose and tap or
washing machine is not tight.
Drain pipe in the room is blocked.

Check and fasten water pipes.
Clean up outlet hose and ask a
specialized person to repair it when
necessary.

Water is
overflowed from
the bottom of the
machine

The inlet pipe is not connected
firmly.
Outlet hose has water leakage.

Fix the inlet pipe.
Replace the drain hose.

Indicator or
display does
not light.

Power is disconnected.
PC board has problems.
Harness has connection
problem.

Check if the power is shut down and
power plug is connected correctly. If
not, please call up service line.

Detergent
residues in the
box

Washing powder is dampened
and agglomerated.

Clean and wipe the box.
Use liquid detergents or the
detergents special for drum.

Washing effects
are not good

The clothes are too dirty.
Insufficient detergent quantity.

Select a proper procedure.
Add the proper detergent quantity
according to the instructions in
detergent package

Abnormal noise
Great vibration

Check if the fixing (bolts) has been
removed. If cabinet is installed on the
solid and level floor. Check if there are
any barrettes or metal articles inside.
Check if the legs in the washing
machine are adjusted level.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

32

Display LED Description Reason Solution

Door lock
problem

Door is not closed
properly

Restart after the door is
closed

Please call up service line if there are still troubles

Water injecting
problem while
washing

Tap is not opened or
water flows too slowly.
Inlet valve filter is
blocked.
Inlet pipe is twisted.
If water is not supplied

Open the tap or wait till the
water supply becomes
normal. Check inlet valve
filter. Straighten the water
pipe. Check the other taps in
the room.

Please call up service line if there are still troubles.

Drain problem
while washing

Outlet hose is blocked
or twisted Drain pump is
blocked

Wash and straighten outlet
hose. Wash drain pump filter

Please call up service line if there are still troubles

CARE SYMBOLS

The label and sign on the fabric can help you to choose the best way to launder
your clothes.

Washing

The figure quoted in the bucket is the maximum temperature the article can be washed at. The
number of bars under the symbol indicates the level of agitation permitted.

No bar under the symbol: = normal agitation

One bar under the symbol: = reduced agitation

Two bars under the symbol: = much reduced agitation

Hand wash (if no temperature is specified, use the lowest temperature or cold)

Do not wash

Door lock
problem

Door is not closed properly.

Restart after the door is closed.

Reason

Solution

Description

Please call up service line if there are still troubles.

Door lock
problem

Door is not closed properly.

Restart after the door is closed.

Reason

Solution

Description

Please call up service line if there are still troubles.

Water injecting
problem while
washing

Tap is not opened or water
flows too slowly.
Inlet valve filter is blocked.
Inlet pipe is twisted.
If water is not supplied

Open the tap or wait till the
water supply becomes normal.
Check inlet valve filter.
Straighten the water pipe
Check the other taps in the
room.

Door lock
problem

Door is not closed properly.

Restart after the door is closed.

Reason

Solution

Description

Please call up service line if there are still troubles.

Drain problem
while washing

Water injecting
problem while
washing

Tap is not opened or water
flows too slowly.
Inlet valve filter is blocked.
Inlet pipe is twisted.
If water is not supplied

Open the tap or wait till the
water supply becomes normal.
Check inlet valve filter.
Straighten the water pipe
Check the other taps in the
room.

Please call up service line if there are still troubles.

Outlet hose is blocked or twisted
Drain pump is blocked

Wash and straighten outlet hose.
Wash drain pump filter

If a problem persists, or more help is required, please contact our
Caple service team on 0117 938 7420 or via email [e-mail]

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

33

Professional cleaning

Dry clean only. The letters indicate the type of
cleaning agent required.

Professional Wet Clean only

Do not dry clean

Bleaching

Any oxidising bleaching agent can be used

Only use an oxygen based bleach or a non-chlorine bleach

Do not bleach

Drying

The number of dots indicates the drying temperature

Dimension(W* D*H)

Net Weight

Rated Power

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

6.0kg

220-240V~,50Hz

Product code

WMI3000

Normal temperature

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

6.0kg

220-240V~,50Hz

Product code

WMI3000

Low temperature

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Standard Water Pressure

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

0.05MPa~1MPa

6.0kg

220-240V~,50Hz

Product code

WMI3000

Do not tumble dry

Ironing

The number of dots indicates the ironing temperature

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Standard Water Pressure

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

0.05MPa~1MPa

6.0kg

220-240V~,50Hz

Product code

WMI3000

Hot iron (max. temperature approx. 200°C)

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Standard Water Pressure

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

0.05MPa~1MPa

6.0kg

220-240V~,50Hz

Product code

WMI3000

Medium hot iron (max. temperature approx. 150°C)

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Standard Water Pressure

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

0.05MPa~1MPa

6.0kg

220-240V~,50Hz

Product code

WMI3000

Cool iron (max. temperature approx. 110°C).
Do not steam iron articles carrying this symbol as this could cause
irreversible damage.

Dimension(W* D*H)

Net Weight

Rated Power

MAX.Current

Standard Water Pressure

Washing Capacity

Power Supply

595* 540*825

57kg

2000W

10A

0.05MPa~1MPa

6.0kg

220-240V~,50Hz

Product code

WMI3000

Do not iron

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

34

Product code WMI3000 WMI3005

Washing Capacity 6.0kg 8.0kg

Dimension(W* D* H) 595* 540* 825 595* 540* 825

Net Weight 57kg 63kg

Rated Power 2000W 2000W

Power Supply 220-240V~,50Hz 220-240V~,50Hz

MAX.Current 10A 10A

Standard Water
Pressure

0.05MPa~1MPa

0.05MPa~1MPa

PRODUCT SPECIFICATIONS

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

35

ELECTRICAL WARNING

To avoid fire,electrical shock and other accidents,please
remember the following:

- Only the voltage indicated in rating label can be used. If
you are not clear of the voltage at home, please contact a
local electrician

- When you are using the heating function, the maximum
current through the washing machine will reach 10A.
Therefore, please make sure the power supply units
(current, voltage and cable) can meet the normal load
requirements for the machine.

- Protect the power cord properly. Power cord shall be fixed
well so that it will not trip the people or other things and
be damaged. Special attention shall be paid to the socket.
It shall be plugged into the sockets easily and attention
shall be paid to the plug location.

- Do not make the wall-mounted socket overloaded or
cable extended. Overloading of the wiring may cause fire
or electrical shock. Do not pull out power plug with wet
hand.

- To ensure your safety, power plug shall be inserted into an
earthed three-pole socket. Carefully check and ensure that
your socket is properly and reliably earthed.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

36

PRODUCT FICHE

MODEL: WMI3000

Rated capacity:6kg
Energy efficiency class:A++

Energy consumption 173kwh per year, based on 220 standard washing cycles for
cotton at 60° C/40°C at full and partial load, and the consumption of the low­power modes. Actual energy consumption will depend on how the appliance is
used.

Water consumption 9240 litres per year, based on 220 standard washing cycles for
cotton 60° C /40°C at full and partial load. Actual water consumption will depend
on how the appliance is used.

Spin-drying efficiency class B on a scale from G (least efficient) to A (most efficient)
Maximum spin speed:1200rpm

Consumption values(1200rpm):

NOTES:

1. Programme setting for testing in accordance with applicable standard
EN60456-2016.

2. When using the test programmes, wash the specified load using the maximum
spin speed.

3. The actual parameters will depend on how the applicance is used,and maybe
different with the parameters in above mentioned table.

Off mode power consumption:0.5W
Left-on mode power consumption:1.0W

Airborne acoustical noise (washing):57
Airborne acoustical noise (spinning):74

NOTES: The airborne acoustical noise emissions during washing/spinning for the
cotton 60° C programme at full load.

Standard
Programme

Load Energy

consumption

Water
consumption

Remaining
moisture
content

Programme
duration

Cotton 60°C 6kg 0.88kwh 48L 50% 277 min

Cotton 60°C 3kg 0.66kwh 37L 55% 246 min

Cotton 40°C 3kg 0.69kwh 37L 55% 245 min

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

37

PRODUCT FICHE

MODEL: WMI3005

Rated capacity: 8kg
Energy efficiency class: A+++

Energy consumption 196kwh per year, based on 220 standard washing cycles for
cotton at 60° C/40°C at full and partial load, and the consumption of the low­power modes. Actual energy consumption will depend on how the appliance is
used.

Water consumption 11000 litres per year, based on 220 standard washing cycles for
cotton 60°C /40°C at full and partial load. Actual water consumption will depend
on how the appliance is used.

Spin-drying efficiency class B on a scale from G (least efficient) to A (most efficient)
Maximum spin speed:1400rpm

Consumption values(1400rpm):

NOTES:

1. Programme setting for testing in accordance with applicable standard
EN60456-2016.

2. When using the test programmes, wash the specified load using the maximum
spin speed.

3. The actual parameters will depend on how the applicance is used,and maybe
different with the parameters in above mentioned table.

Off mode power consumption:0.5W
Left-on mode power consumption:1.0W

Airborne acoustical noise (washing):57
Airborne acoustical noise (spinning):76

NOTES: The airborne acoustical noise emissions during washing/spinning for the
cotton 60° C programme at full load.

Standard
Programme

Load Energy

consumption

Water
consumption

Remaining
moisture
content

Programme
duration

Cotton 60°C 8kg 0.94kwh 54L 50% 229 min

Cotton 60°C 4kg 0.94kwh 45L 55% 209 min

Cotton 40°C 4kg 0.67kwh 45L 55% 166 min

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

38

BUILT-IN INSTALLATION

Overview

Before installing the washing machine, please read these built-in instructions
carefully and keep it for future reference. This appliance has been designed to be
built into the kitchen furniture. The recess should have the dimensions as shown in
figure below.

Before installed the washing machine, please read this Built-In instructions carefully
and keep it for future reference. This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions shown in Fig.

Overview

825 mm

600mm

825mm

540 mm

595 mm

152.5mm

17.5mm

560mm

WARNING

When installing the appliance into the kitchen, if possible,
ensure the hoses are placed in either of the two recesses
on the back of the appliance. This will help to prevent the
hoses from becoming kinked or trapped.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

39

Before installed the washing machine, please read this Built-In instructions carefully
and keep it for future reference. This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions shown in Fig.

Overview

When installing the appliance into the kitchen, if possible, ensure the hoses are placed in either
of the two recesses on the back of the appliance. This will help to prevent the hoses from
becoming kinked or trapped.

Preparation and assembly of the door

The appliance is prearranged for the assembly of a door opening from right to left or from left to
right.

825 mm

600mm

825mm

540 mm

595 mm

152.5mm

17.5mm

560mm

Preparation and assembly of the door

The appliance is prearranged for the assembly of a door opening from right to left
or from left to right.

Door opening from left to right Door opening from right to left

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

40

BUILT-IN INSTALLATION

2.Fix door template onto the door.

Top Top

1

2

2.Fix door template onto the door.

Top Top

1

2

4

3

2.Fix door template onto the door.

Door template Door template

Top Top

5

1

2

4

3

6

1.Drill the holes on the door according to the door template

2.Fix door template onto the door.

Paste on the Door(The door on the right)

Cut door template paper

Drill holes on the door

Door template Door template

Top Top

Left Open

Right Open

5

1

2

4

3

6

1

2

3

4

2.Installing the hinges and spacer

Fix the hinges to the furniture door with the ST4*12 screws. The hinges can be adjusted to compensate for
possible uneven thickness of the door.

1.Drill the holes on the door according to the door template

2.Fix door template onto the door.

Cut door template paper

Drill holes on the door

Top Top

Left Open

Right Open

Appendix

Preparation the Fixed position paper

1. Make the mark on the door according to the cupboard and washing machine height.

1.Self-tapping screws
(ST4*12)

2.Self-tapping screws
(M5*12)

3.Hinges

4.Counter magnet

5.Spacer

6.Door template

Tools

1.

2.Automatic Driver

3.Ruler

4.Pencil

Screw Driver

5

1

2

4

3

6

1

2

3

4

Door template

Appendix

1. Self-tapping screws
(ST4*12)

2. Self-tapping screws
(M5*12)

3. Hinges

4. Counter magnet

5. Spacer

6. Door template

Tools

1. Screw Driver

2. Automatic Driver

3. Ruler

4. Pencil

Door template preparation

1. Make the mark on the door according to the
cupboard and washing machine height.

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

41

2.Fix door template onto the door.

Door template Door template

Top Top

Left Open

Right Open

Paste on the Door(The door on the right)

Door template Door template

16-22mm

12mm

35mm

12mm

2mm

Paste on the Door(The door on the left)

Right Open

Door template Door template

16-22mm

12mm

35mm

12mm

2mm

Paste on the Door(The door on the left)

Drill holes on the door

1. Drill the holes on the door
according to the door template

2. Installing the hinges and spacer
Fix the hinges to the furniture
door with the ST4*12 screws.
The hinges can be adjusted to
compensate for possible uneven
thickness of the door.

2. Fix door template onto the door.

Cut door template
paper

Paste on the Door
(The door on the right)

Paste on the Door
(The door on the left)

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

42

Installing the door magnet

The appliance is designed with magnetic closure of the door. To enable a
correct operation of this device, it is necessary to screw the counter-magnet
into the inner side of the door.

Installing the door magnet

The appliance is designed with magnetic closure of the door. To enable a correct operation of
this device, it is necessary to screw the counter-magnet into the inner side of the door.

Installing the door magnet

The appliance is designed with magnetic closure of the door. To enable a correct operation of
this device, it is necessary to screw the counter-magnet into the inner side of the door.

Installing the door

Bristol
BS11 8DW

t: 0117 938 7420
e: [e-mail]
www.caple.co.uk

Caple Service
Fourth Way
Avonmouth

Installing the door

NOTE: The furniture door should not exceed 9kg

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

43

Instruction manual WMi3000 / WMi3005

Please keep this instruction manual for future reference

44

Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW

t: 0117 938 7420
e: [e-mail]
www.caple.co.uk