Caple WDI1210 Instruction Manual

Page 1

WDI1210 user manual.doc

INSTALLATION AND OPERATING

INSTRUCTION BOOKLET

WDI1210

INTEGRATED WASHER DRYER

THIS APPLIANCE COMPLIES WITH EUROPEAN DIRECTIVES

EMC 89/336/ECC

LOW VOLTAGE 73/23/ECC

ECC-LABELLING 93/68/ECC

IMPORTANT: You must read this instruction book before

installing or using this appliance and retain it for future use.

Caple Products

Telephone [phone]

Facsimile 0117 982 6878

Page 2

WDI1210 user manual.doc

INSTALLATION INSTRUCTIONS
Positioning

After your washing machine has been placed in the desired
location, level it by means of the front left foot, then the counter
nut must be locked by means of the special key provided.

Warning: if the machine is not perfectly leveled, it will be
unstable, noisy and may lead to malfunctions and broken
parts. Do not place the machine on mats or carpets.

Water connection

COLD WATER HOSE = WHITE HOSE
HOT WATER HOSE = BLACK HOSE

Connect the water supply hoses to hot & cold-water taps with a 3/4" (gas
type) fitting insert the rubber sealing washers supplied with the machine
and fully tighten the ring nuts. If the water tap is new or has not been
used for a long time it is recommended to let the water run for a while
before completing the connection. Connect the other end of the water
supply hose to the machine and again insert the rubber washer between
the hose and the solenoid valve fitting.

Drain Hose

Insert the drain hose into a drain pipe (with a minimum
internal diameter of 4cm) or hook it on a sink or bathtub,
without crimping or creating any sharp curves. The hose should
be positioned at a height ranging from a minimum of 60cm to a
maximum of 100cm, as shown in the figure.

Electrical Connection

Make sure that the electrical system can support the maximum current load indicated on the
rating plate on the rear side of the machine. The washing machine should be connected to
an electrical grounded outlet, as prescribed by law. This outlet must be easily accessible
after the installation of the washing machine.

If the supply card is damaged, it should be replaced by a special cable available
at the manufacturers or at the technical service.

The company will not be responsible for any damage to persons or things due to
non-compliance with these instructions.

CLEANING AND MAINTENANCE

This washing machine does not require any particular maintenance. At the end of each wash
it is recommended to leave the door open so that air will circulate and dry the interior of the

Page 3

WDI1210 user manual.doc

machine. The external parts of the machine should never be cleaned with abrasive
detergents since this would ruin the enamel coating as well as the synthetic parts.

Page 4

WDI1210 user manual.doc

Removing and cleaning filter

Remove the plastic base guard at the bottom of the machine by
pressing and pulling upwards on the two tabs.

Place a rag under the washing machine to adsorb any residual
water. The filter is located under the base. Turn the filter handle
counterclockwise and pull out the filter. Clean it under running
water. Reinsert the filter and turn the handle clockwise until it is
completely locked. WARNING: water may leak from the filter if it is

not properly tightened. Remember to clean the filter frequently to
avoid excessive clogging.

TECHNICAL FEATURES

Length 595 mm
Depth 530 mm
Height 850 mm

Capacity

Cotton 5 kg max. of dry linen
Synthetic and mixed fabrics. 2,5 kg max. of dry
linen
Wool 1 kg max, of dry linen
Voltage and frequency 230 V / 50 Hz

Fuse 10 amp
Water pressure required in water mains min. 0.1 Mpa (1 Bar)
max. 1.0 Mpa (10 Bar)

BEFORE CALLING THE TECNICAL SERVICE CENTRE

Check if plug is inserted

Check that power is available

Check that the doer is properly closed

Check that the water tap is open

Check that the water supply hose and water drain hose are not blocked

NOTE: - if you have to call the service centre, specify the model of your washing
machine and if necessary the Serial Number which is indicated on the rating plate on the
back of the machine.

How to use your washing machine economically and ecologically.
Optimum load - Always try to use the washing machine at full load, as this will use less

water, washing powder and energy than two smaller loads.
You want to use the pre-wash? - Only use the pre-wash for very dirty linen. If you don't

use the pre-wash, you save from 5% to 15% in energy, washing powder, water and time.
Is a high temperature wash required? - To avoid high temperature washing, treat

particularly dirty items with a stain remover or leave the worst stains to soak beforehand.
You will save energy in this way.