Caple CM471WH, CM461, CM471SS User Manual
Instructio
Instruction manual for
InstructioInstructio
n manual for built
n manual for n manual for
Model code: CM461 CM471SS / WH
built----in coffee
builtbuilt
in coffee machine
in coffee in coffee
machine
machinemachine
Contact Caple on 0844 800 3830 or for spare parts www.caple.co.uk
Dear Customer,
we would like to thank you and congratulate you on your
choice.
This new product has been carefully designed and built
using top quality materials, and meticulously tested to
ensure that it meets all your culinary requirements.
Please read and observe these simple instructions, which
will enable you to achieve excellent results from the very
first time you use it. This state-of-the-art appliance comes
to you with our very best wishes.
THE MANUFACTURER
THIS PRODUCT IS DESIGNED FOR DOMESTIC USE.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR DAMAGES TO THINGS
OR PEOPLE DERIVING FROM INCORRECT
INSTALLATION OR IMPROPER, ERRONEOUS OR
UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED BY PEOPLE
(INCLUDING CHILDREN) WITH PHYSICAL,
SENSORIAL OR MENTAL IMPAIRMENTS, OR BY
PEOPLE WITHOUT THE NECESSARY EXPERIENCE
OR KNOWLEDGE, UNLESS THEY ARE SUPERVISED
OR INSTRUCTED IN THE USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
3
CHILDREN MUST BE SUPERVISED TO ENSURE
THAT THEY DO NOT PLAY WITH THE APPLIANCE.
CONTENTS
1. FOR YOUR SAFETY
• During use
• For installation and maintenance
2. RECOMMENDATIONS FOR THE PROTECTION OF
THE ENVIRONMENT
• Packing
• Obsolete equipment
3. INSTALLATION
• Installation in modular furniture
• Components for the installation of the machine
• Installation of the machine
• Electrical connection
4. DESCRIPTION OF THE COFFEEMAKER
5. TECHNICAL CHARACTERISTICS
• Fuses
6. DESCRIPTION OF THE CONTROL PANEL TOUCH
BUTTONS
7. FIRST USE
• Fill the water tank
• Fill the container with coffee beans
• Turning on the machine in standby mode
• Regulation of the ground coffee
• Wash function
8. DISPENSING COFFEE
9. DISPENSING HOT WATER
10. DISPENSING STEAM
11. PROGRAMMING THE QUANTITY OF GROUND
COFFEE
12. PROGRAMMING THE QUANTITY OF HOT WATER
• Restoring the factory settings
13.ILLUMINATION OF THE DISPENSING
COMPARTMENT
14. WARNINGS AND ALARMS
• No water warning
• Replace filter warning
• Coffee grounds warning
• Coffee probe broken warning
• Generic alarm warning
15. RECIPES
• Italian Cappuccino
• Viennese Cappuccino
• Cold Espresso Chilled in a Shaker
• Irish coffee
• Mexican Coffee
• Cappuccino Ice Cream
16. CLEANING AND MAINTENANCE
• External parts
• Steam nozzle
• Drip basin
• Emptying used coffee grounds
• Water tank
17. TROUBLESHOOTING
18. SERVICE, REPLACEMENT PARTS AND
WARRANTY
SYMBOLS
Durante la lettura del manuale vi capiterà di incontrare i
seguenti simboli:
ATTENTION: important instructions for the
safe and correct use of the machine
information useful for the optimal use of the
equipment.
4
1. FOR YOUR SAFETY
Although the machine is simple to use, it is important
that you read the entire booklet before installing or
using the machine for the first time. By doing so, you will
achieve the best performance, avoid mistakes, use the
machine in absolute safety and protect the environment.
During use
• This machine must only be used by adults. Otherabled persons can use the machine only if there is a
person responsible for their safety that will supervise
and instruct them in the use of the machine.
• Make sure that children do not touch the controls or
play with the machine.
• This machine is intended for home use; another
other use is considered improper and, therefore,
dangerous.
• Always keep the machine clean.
• It is dangerous to modify, or attempt to modify, the
characteristics of this product.
• The exposed parts of this machine get hot during
operation and remain hot for a certain period of time
after it is turned off. Keep children away until the
machine has cooled.
• Do not touch the hot surfaces during use but use the
knobs or handles.
• Make sure the machine is disconnected from the
electric mains before any maintenance or cleaning.
• If the machine breaks, do not try and repair it yourself.
Repairs made by unqualified persons can cause
damage and accidents. Consult the contents of this
booklet. If you don’t find the information you need,
contact the nearest service centre. This machine
must be serviced by an authorised Service Centre.
Always request the use of original replacement parts.
For installation and maintenance
• After unpacking the machine, check that the product
has not been damaged and that the power cord is
in perfect condition. If not, contact the reseller before
operating the machine.
• The packing materials (plastic bags, styrofoam, etc.)
must not be left within the reach of children because
they are potentially dangerous.
• Before use, check that the voltage and power listed
on the machine’s nameplate match the line to which
it will be connected. Also make sure that the building
has an efficient earth line and a suitable circuit
breaker.
• Any service must be performed by specialised
personnel.
• The manufacturer will not be liable if these rules are
not followed.
2. RECOMMENDATIONS FOR THE
PROTECTION OF THE ENVIRONMENT
Packing
All packing materials used are safe for the environment
and recyclable. Please make your contribution to
protecting the environment by disposing of the packing
in the appropriate recycling bins.
Obsolete equipment
• Machines that are obsolete or no longer used should
not be thrown away in the trash. Through ecological
disposal, the various materials used in the production
of your machine can be recovered.
• Ask your specialised reseller or your city administration
about disposal options.
• Before scrapping the machine, cut the power cord to
make it unusable.
It is very important to keep this instruction booklet for
future consultation. If the machine is sold or given to
another person, make sure to give the booklet to the new
user so that they will be informed about the operation of
the machine and the relative warnings.
This symbol on the product or packaging means
that the product must not be thrown away in household
waste but must be taken to a collection point for recycling
electrical and electronic equipment. By disposing of this
product properly, you will avoid potential damage to the
environment and health caused by the incorrect disposal
of the product. For more detailed information about
recycling this product, contact your city administration,
local waste disposal service or the store where you
purchased it.
3. INSTALLATION OF THE MACHINE
“BUILT-IN” INSTALLATION IN MODULAR FURNITURE
For the good operation of the machine when builtin to modular furniture, the latter must have suitable
characteristics.
In conformity with safety standards, protection against
contact with electrical parts and parts protected with
just functional insulation must be provided through the
correct housing of the machine.
All the parts that provide protection, including any
covering panel (for example, if the machine is positioned
at the end or beginning of the modules), must be
fastened in such a way that they cannot be removed
with the aid of a tool.
It is also a good idea to install the machine at a certain
distance from refrigerators or freezers because the heat
it emits could affect their operation.
5
Components for the installation of the machine
The machine must be installed in compartments that are
460 mm high and between 560 and 568 mm wide. The
following installation components are supplied with the
machine.
1. Fixed support of the machine.
2. N°13 self-threading screws 3.9X19
3. N°1 fixed power cord
4. N°2 lateral guides
5. N°2 lateral 1-mm plates
6. N°2 lateral 2-mm plates
Installation of the machine
Position the fixed part provided
by resting it on the surface of
the furniture
Insert the side plates needed to compensate for any
empty spaces. The width of the compartment that
houses the machine is determined by the thickness of
the sides of the furniture. Four plates are supplied to
compensate for the different measures obtainable, two
that are 2 mm thick and two that are 1 mm thick. They
are used to compensate for the internal width of the
compartment to obtain an measurement of 562-560 mm.
Then mount the 2 guides
using the remaining 8
self-threading screws.
Insert the machine
by matching up
the guides with the
supports already
mounted in the
compartment.
Slide it all the way in until the
safety stops click.
6
Loading...