Page 1
Sense Combination Microwave
Instruction Manual
CM110GM
Contact Caple on 0117 938 7420 for spare parts or www.caple.co.uk
Page 2
CONTENTS
Warnings 3
Environmental protection 10
Warranty 10
Installation 12
Dimensions 14
Electronic connection 15
Control panel / display 16
Accessories 17
Operation 19
Microwave oven functions 21
Auto cooking 23
Defrost time table 26
Demo mode 27
Care and maintenance 28
Removing the oven door 29
Troubleshooting 28
Technical data 30
Caple contact details 32
Instruction manual CM110GM2
Please keep this instruction manual for future reference
Page 3
GENERAL WARNINGS
Read carefully all the instructions contained in this
manual. It provides you with important information
regarding the safe installation, use and maintenance of
the appliance as well as useful advice for getting the best
out of your microwave oven. Keep this booklet in a safe
place for future reference. After removing the packing,
check that the appliance is not damaged in any way.
Be careful not to leave the packing materials (plastic
sheeting, expanded polystyrene etc.) where children can
get at them, as they can be dangerous.
IMPORTANT:
Do not use the oven door handle to move the appliance,
such as to remove it from the packaging.
ATTENTION:
The microwave oven is an appliance which, for its nature,
becomes hot during use, especially the glass door.
It is therefore a good rule that children do not approach
the microwave oven when it is functioning, particularly
when the grill is in use.
Before you use the microwave oven for the first time, heat
the empty oven at max. temperature for 1 hour, removing
any unpleasant smells and smoke caused by working
residues and thermal insulation. Make sure you do this in
a well ventilated area.
Please keep this instruction manual for future reference
Instruction manual CM110GM 3
Page 4
Never roast or bake on the oven base.
This product is not designed for commercial use, it is a
household appliance only. It is not intended to be used in:
- Staff kitchen areas in shops, offices and other
working environments.
- Bed and breakfast type environments.
- By clients in hotels, motels and other residential
ype environments.
The electrical system of this appliance may be used safely
only when it is correctly connected to an efficient earthing
system in compliance with the safety standards currently
in effect.
The manufacturer will not be held liable for any damages
that might arise out of incorrect or improper use of
the appliance.
The following items are potentially dangerous, and
therefore, appropriate measures must be taken to prevent
children and the disabled from coming into contact
with them:
- Controls and the appliance in general;
- Packaging (bags, polystyrene, nails, etc.);
- The appliance immediately after use of the oven or grill
due to the heat generated;
- The appliance when no longer in use (potentially
dangerous parts must be made safe).
Instruction manual CM110GM4
Please keep this instruction manual for future reference
Page 5
WARNING:
Accessible parts will become hot when in use. To avoid
burns and scalds children should be kept away.
During use the appliance becomes hot, Care should be
taken to avoid touching heating elements inside the oven.
- If the door or door seals are damaged, the oven must
not be operated until it has been repaired by a Caple
approved engineer.
- It is hazardous for anyone other than a competent
person to carry out any service or repair operation that
involves the removal of a cover which gives protection
against exposure to microwave energy.
- Liquids and other foods must not be heated in sealed
containers since they are liable to explode.
- Only use utensils that are suitable for use in
microwave ovens.
- When heating food in plastic or paper containers, keep
an eye on the oven due to the possibility of ignition.
- The microwave oven is intended for heating food and
beverages. Drying of food or clothing and heating of
warming pads, slippers, sponges, damp cloth and similar
may lead to risk of injury, ignition or fire
- The oven should be cleaned regularly and any food
deposits removed
- Failure to maintain the oven in a clean condition could
lead to deterioration of the surface that could adversely
affect the life of the appliance and possibly result in a
hazardous situation
Please keep this instruction manual for future reference
Instruction manual CM110GM 5
Page 6
WARNING:
To reduce the risk of burns, electric shock, fire, injury to
persons or exposure to excessive microwave energy:
- Make sure that all the packing materials are removed
from the inside of the door.
WARNING:
- Check the oven for any damage, such as misaligned
or bent door, damaged door seals and sealing surface,
broken or loose door hinges and latches and dents inside
the cavity or on the door. If there is any damage, do not
operate the oven and contact Caple service immediately.
- This microwave oven must be placed on a flat, stable
surface to hold its weight and the heaviest food likely to
be cooked in the oven.
- Do not place the microwave oven where heat,
moisture, or high humidity are generated, or near
combustible materials.
- Do not operate the microwave oven when empty.
- Do not operate this appliance if it has a damaged cord
or plug, if it is not working properly or if it has been
damaged or dropped. If the supply cord is damaged, it
must be replaced by Caple or an approved engineer in
order to avoid a hazard.
Instruction manual CM110GM6
Please keep this instruction manual for future reference
Page 7
WARNING:
- Liquid or other food must not be heated in sealed
containers since they are liable to explode.
- Microwave heating of liquids can result in delayed
eruptive boiling, therefore care has to be taken when
handling the container.
- Do not fry food in the microwave oven. Hot oil can
damage oven parts and utensils and even result in
skin burns.
- Eggs in their shell and whole hard-boiled eggs should
not be heated in microwave ovens since they may
explode even after microwave heating has ended.
- Pierce foods with heavy skins such as potatoes, whole
squashes, apples and chestnuts before cooking.
- The contents of feeding bottles and baby jars should
be stirred or shaken and the temperature should be
checked before serving in order to avoid burns.
- Utensils should be checked to ensure that they are
suitable for use in microwave oven.
Please keep this instruction manual for future reference
Instruction manual CM110GM 7
Page 8
WARNING:
- It is hazardous for anyone other a trained person to
carry out any service or repair operation which involves
the removal of any cover which gives protection against
exposure to microwave energy.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless the have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
- Children should be supervised to ensure that they do not
play with the appliance.
- When heating food in plastic or paper containers, check
the oven frequently for the possibility of ignition.
- Remove wire ties from paper or plastic bags before
placing bag in oven.
- If smoke is observed. Switch off or unplug the appliance
and keep the door closed in order to stifle any flames.
- Do not leave paper products, cooking utensils or food in
the cavity when not in use.
Instruction manual CM110GM8
Please keep this instruction manual for future reference
Page 9
WARNING:
- The appliance and its accessible parts become hot
during use.
- Care should be taken to avoid touching
heating elements.
- Children less than 8 years of age shall be kept away
unless continuously supervised
- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
- During use the appliance becomes hot. Care should be
taken to avoid touching heating elements inside
the oven.
WARNING:
Accessible parts may become hot during use. Young children
should be kept away.
Please keep this instruction manual for future reference
Instruction manual CM110GM 9
Page 10
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. The symbol on the product indicates
that this product may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. Disposal must
be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local council, your household waste disposal service or the retailer where you
purchased the product.
CE DECLARATIONS OF CONFORMITY
This appliance has been designed, constructed and marketed in compliance with safety
requirements in force. This appliance has been manufactured to the strictest standards and
complies with all applicable legislation.
WARRANTY
Your new appliance is covered by warranty. The warranty card is enclosed - if it is missing, you
must provide the following information to your retailer in order to receive a replacement: date
of purchase, model and serial number (placed on the inside of the appliance storage drawer).
Registration can also be completed online by visiting www.caple.co.uk.
Ensure you keep your warranty card safe, you may need to show it to Caple Service together with
proof of purchase.
If you fail to show your warranty card you will incur all repair charges.
Spare parts are only available from Caple Service and spare parts authorised centres.
Instruction manual CM110GM10
Please keep this instruction manual for future reference
Page 11
ATTENTION
» Before use, remove all plastic films protecting some parts of the appliance (fascia - panel, parts
in stainless steel, etc)
» Do not use the appliance to heat a room.
» When the appliance is not in use, we recommend you turn it off, isolate it from the
electrical supply.
Please keep this instruction manual for future reference
Instruction manual CM110GM 11
Page 12
INSTALLATION
IMPORTANT:
Isolate your microwave oven from the electrical supply before performing installation
or maintenance.
Installation should be carried out according to the instructions by a professionally qualified
person only.
The manufacturer declines all responsibility for any damage to persons, animals or materials due
to incorrect installation.
The Combi-Microwave requires a sufficient supply of cool air for efficient operation. Make sure
that the supply of cool air is not hindered in any way (e.g. by fitting heat insulation strips in the
cabinet carcase). Furthermore the required supply of cool air must not be excessively heated by
other heat sources.
Instruction manual CM110GM12
Please keep this instruction manual for future reference
Page 13
Fig.2
FITTING THE APPLIANCE
Fit the appliance into its surround (beneath a
worktop or above another appliance in a tall
housing) by inserting screws and plastic covers into
the 4 holes (A - fig.3) that can be seen in the frame
of the oven when the door is open.
For the most efficient air circulation,
the microwave oven should be
fitted according to the dimensions
Ventilation Slot
shown in fig.1.
The rear panel of the cabinet must
70mm
be removed so that air can circulate
freely. The panel to which the
microwave oven is fitted should
min. 550mm
have a gap of at least 70 mm at the
rear for ventilation (fig.4 & fig.5).
Fig.3
Plastic cover
70mm
565mm
450mm
8.6mm
547.4mm
22mm
21.6mm
453.6mm
595mm
Please keep this instruction manual for future reference
Instruction manual CM110GM 13
Page 14
See below for full dimensional drawings of your microwave oven to help
with installation.
For a built-in oven microwave to work well the cabinet must be of the right type.
The panels of the adjoining furniture should be heat resistant. Particularly when the adjoining
furniture is made of veneered wood, the adhesives should be able to withstand a temperature
of 120ºC. Plastic materials or adhesive which cannot withstand this temperature may become
deformed or unstuck.
To comply with safety regulations, once the appliance has been fitted it should not be possible to
make contact with the electrical parts.
All parts which offer protection should be fixed in such a way that they cannot be removed
without the use of a tool.
MICROWAVE OVEN DIMENSIONS
116mm
453.6mm
Instruction manual CM110GM14
595mm
547mm
8mm
569mm
Please keep this instruction manual for future reference
22mm
8.6mm
2.8mm
26.4mm 26.4mm
Page 15
ELECTRICAL CONNECTION
WARNING:
This appliance must be earthed.
Check that the power rating of the mains supply is suitable for the maximum power of the
appliance as indicated on the rating label. The fuse rating for this appliance is 13amp.
The appliance is supplied with a mains lead it should be “Hard wired” as follows:
1. The “yellow/green” earth wire, which must be connected to a terminal, and has to be about
10mm longer than the other wire.
2. The neutral wire has to be connected to the terminal marked with a letter N.
3. The Live wire should only be connected to the terminal marked L.
Mains connection can also be made by fitting a double pole switch with a minimum gap between
the contacts of 3mm, proportionate to the load and complying with the regulations in force.
THE YELLOW/GREEN EARTH WIRE SHOULD NOT BE CONTROLLED BY
THE SWITCH.
When a double pole switch is used for mains supply connection it should be easily accessed, once
the appliance is in position.
Please keep this instruction manual for future reference
Instruction manual CM110GM 15
Page 16
CONTROL PANEL
IMPORTANT:
The mains supply cable should be positioned so that it is never subjected to temperatures which
are more than 50ºC above ambient temperature.
The electrical safety of the appliance can only be guaranteed when it has been correctly connected
to a properly earthed mains electrical supply, as laid down in the current regulations for electrical
safety.
The manufacturer cannot be held responsible for any damage to persons or objects due to lack of
an earth connection.
The ovens are designed to operate with a mono-phase alternating current of
220-240V, 50Hz.
BEFORE THE INSTALLATION OF THE APPLIANCE, CHECK THE
SPECIFICATIONS ON THE RATING LABEL.
CONTROL PANEL
˚C / W / g
AUTO
1
2
5
1. Power
2. Programme
3. Timer
4. Temperature ºC / Power (watts) /
Weight (grams)
5. Auto cooking
Instruction manual CM110GM16
3
4
6. Up
7. Down
8. Select
9. Light / Child lock
10. Start / Pause
Please keep this instruction manual for future reference
6
7
8
9
10
Page 17
DISPLAY
6
. Up
7. Down
8
. Select
9
. Light / Child lock
10
. Start/pause
NING: Do not use the enameled tray with any microwave function. This could
Fig.1
C
ES
S
O
R
IES
e
s
h
e
lf
(
Fig
.1)
m
e
le
d
t
r
a
y
(
Fig
.2
)
NING
: Do not use the enameled tray with any microwave function. This could
s
id
e
s
he
lf
supp
or
t
s
(
Fig
.3
)
TE: Always remove the enameled tray when using microwave functions, as this
Fig.1
Fig.3
3
4
2
1
12
1. Programme / Function
2. Microwave
3. Defrost
4. Auto cooking
5. Temperature / Power /
Weight (grams)
ACCESSORIES
13
6. Timer
7. Time
8. Child lock
9. Light
10. Alarm
5
6
7
8
9
11
10
11. End time
12. Duration time
13. Temperature / Time Display
WIRE SHELF (FIG.1)
The wire shelf allows you to brown or grill food. The shelf can be
used for normal fan heat, conventional cooking and grilling
functions only. It must not be used for any microwave function.
If a microwave function is selected, ensure the wire shelf has been
removed before the start.
ENAMELED TRAY (FIG.2)
The enameled tray allows you to cook foods on normal fan heat,
conventional cooking, and grilling functions. The silicone corners
applied to the enameled tray also allows it to be used in combi
microwave functions. This tray cannot be used during the microwave
only function. Ensure it is removed before using microwave only.
Please keep this instruction manual for future reference
Fig. 1
Fig. 2
Instruction manual CM110GM 17
Page 18
NOTE:
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Do not remove the silicone corners, as this could damage the oven.
WARNING
» Do not use the wire shelf with any microwave function. This could damage the shelf or even
your microwave oven. The wire shelf is for normal convection/Fan cooking or grilling only.
» Do not use the enameled tray with the microwave only function
THE SIDE SHELF SUPPORTS (FIG.3)
2 hook-on shelf supports allow you to use the accessories on three
levels. Three cooking levels are available, depending on the method used
and the type of food. With the Grill or Grill + Microwave setting, the
accessories (shelf or tray) are placed on the first level for thick foods like
roasts and on the third level for thinner foods like sausages. In normal
cooking modes, or microwave functions, the shelf or tray should be used
on the first or second levels depending on the item(s) being cooked.
GLASS BASE PLATE (FIG.4)
When microwaving only, foods and beverages can be placed on the
Glass base plate. The Glass base plate protects the bottom of the
microwave cavity from any scratches, marks or spillages. It can also
be easily removed for cleaning by either hand or in the dishwasher.
Fig. 3
NOTE:
Always remove the wire shelf when using microwave functions, as this could damage the oven.
Instruction manual CM110GM18
Please keep this instruction manual for future reference
Fig. 4
Page 19
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the
The main timer will show the actual
temperature, with the set temperature shown above this.
O T O
mode
T to conrm.
The main timer will show the actual
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
OPERATION
, SELECT, and
OPERATION
O T O
mode
T to conrm.
The main timer will show the actual
O T O
have button to enter the
mode
T to conrm.
The main timer will show the actual
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Fan Heat
O T O
have button to enter the
mode
T to conrm.
The main timer will show the actual
button once to turn the internal microwave oven lights on o. The lights
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Fan Heat
O T O
mode
T to conrm.
The main timer will show the actual
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
O T O
mode
T to conrm.
The main timer will show the actual
button once to turn the internal microwave oven lights on o. The lights
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Fan Heat
O T O
have button to enter the
mode
T to conrm.
The main timer will show the actual
button once to turn the internal microwave oven lights on o. The lights
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Fan Heat
O T O
have button to enter the
mode
T to conrm.
The main timer will show the actual
button once to turn the internal microwave oven lights on o. The lights
Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Fan Heat
T to conrm.
Press the button to turn the oven on. When turned on, the display will light up and the time of
day will be shown.
PROGRAMME / FUNCTION:
To select a function, press the PROG button to toggle through the functions and press SELECT
once you have reached the required function. Press the °C/W/g button to enter the temperature
(°C) , power (W) or weight (g) mode depending on what function has been selected.
To adjust the temperature, power or weight, use the keys followed by SELECT to confirm.
Once confirmed, press the button to start cooking. The main timer will show the actual
temperature, with the set temperature shown above this.
/
Microwave & Turbo Conventional
Microwave & Turbo Grill
LIGHT FUNCTION:
Press the button once to turn the internal microwave oven lights on & off. The lights
will automatically turn off after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
CHILD LOCK:
Hold the button for 2-3 seconds to activate the child lock. To deactivate, press and
hold the button again for 2-3 seconds.
When the Child lock is activated, the symbol will be shown on the display.
Microwave & Fan Heat
Please keep this instruction manual for future reference
Microwave
Defrost
Turbo Conventional Heat
Fan Heat
Turbo Grill
Instruction manual CM110GM 19
Page 20
ALARM SETTING:
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
/
, SELECT, and
To set the Alarm/minute minder, press the button until the symbol starts to flash.
Use to adjust the time, and then press SELECT to confirm. If you want to cancel the
/
alarm, set the alarm time back to ‘0.00’ and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash.
To stop the alarm, press any button.
SETTING THE TIME:
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the and then press SELECT to confirm.
/
When the oven is first turned on or restarts, the time must be set before using
the oven.
DURATION COOKING(0-10HRS)
Once a function and temperature have been selected, press the button and the Duration
time will start to flash. Press to adjust the time, and then SELECT to confirm. Once the
/
time is up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm , SELECT, and
/
To cancel Duration cooking set the cooking time to ‘0:00’ and confirm.
END COOKING TIME
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function
and temperature (start time = End time - duration time).
Instruction manual CM110GM20
Please keep this instruction manual for future reference
Page 21
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
Display
Display
Display
Display
Display
Display
Display
Display
Display
MICROWAVE OVEN FUNCTIONS
Press the PROG button to select the following functions.
MICROWAVE:
Default power P100 (power range P10-P100).
To adjust the power, press until the correct power is
reached followed by SELECT.
Default time is 30 seconds. To adjust the time press the button
followed by the and SELECT to confirm.
The time will increase in 30 seconds increments (Max 60mins).
Note: The Duration time when using the microwave function will
display ‘minutes : seconds’, in all other functions it will show
‘hours : minutes’.
Finally press to start the programme.
DEFROST:
Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the
SELECT to confirm.
and
Finally press to start the programme. The default time will be
adjusted according to the set weight (See the ‘Defrost time table’ for
more info).
FAN HEAT:
Default temperature 200°C
To adjust the temperature press °C/W/g followed by . Press
SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
TURBO GRILL:
Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by . Press
SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
TURBO CONVENTIONAL:
Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by . Press
SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
/
/
/
Please keep this instruction manual for future reference
/
/
/
/
/
/
Instruction manual CM110GM 21
Page 22
MICROWAVE & FAN HEAT:
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Symbol Description
Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Symbol Description
Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
, SELECT, and
Display
Display
Display
Display
Display
Display
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Symbol Description
Display
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROGto select the following functions:
Symbol Description
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Symbol Description
Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
WARNING:
» All programmes which include the Microwave function do not require pre-heating, and must
only be used with food inside the oven.
» The enameled tray cannot be used with the microwave only function
» The wire shelf cannot be used with any microwave function
Instruction manual CM110GM22
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then
again to enter the fan heat temperature mode. These can both then
be adjusted using the keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
MICROWAVE & TURBO GRILL:
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50220°C).
Press °C/W/g once to enter the Microwave power mode, and then
again to enter the Turbo grill temperature mode. These can both then
be adjusted using the keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
MICROWAVE & TURBO CONVENTIONAL HEAT:
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50220°C).
Press °C/W/g once to enter the Microwave power mode, and then
again to enter the Turbo conventional temperature mode. These can
both then be adjusted using the keys followed by SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button
followed by the and SELECT to confirm.
Finally press to start the programme.
/
/
/
/
/
/
Please keep this instruction manual for future reference
Page 23
AUTO COOKING
Display
The default time will be adjusted according to weight
Symbol
Description
Display
The default time will be adjusted according to weight
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Symbol
Description
Display
The default time will be adjusted according to weight
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Soup
500g
500
Microwave
19
800
Microwave
22
Symbol
Description
Display
The default time will be adjusted according to weight
Symbol
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Soup
500g
500
Microwave
19
800
Microwave
22
Noodles
300
300
Microwave
5
600
Microwave
8
Symbol
Description
Display
The default time will be adjusted according to weight
Symbol
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Soup
500g
500
Microwave
19
800
Microwave
22
Noodles
300
300
Microwave
5
600
Microwave
8
200g
100
Microwave
2
200
Microwave
4
300
Microwave
5
400
Microwave
6
Symbol
Description
Display
, SELECT, and
Display
Example:
SYMBOL DESCRIPTION DISPLAY
Milk (Auto programme)
Press the Auto programme button until the Milk symbol is displayed.
Press the °C/W/g to enter the Weight selection. Use the to
adjust the weight and press SELECT to confirm.
The default time will be adjusted according to the weight selected.
Finally press to start the programme.
Auto Cooking Functions
/
SYMBOL
DEFAULT
WEIGHT
250g
500g
Vegetables
300g
200g
Please keep this instruction manual for future reference
WEIGHT
ALTERNATIVES
FUNCTION DURATION
250 Microwave 2
500 Microwave 4
500 Microwave 19
800 Microwave 22
300 Microwave 5
600 Microwave 8
100 Microwave 2
200 Microwave 4
300 Microwave 5
400 Microwave
500 Microwave
600 Microwave
Instruction manual CM110GM 23
6
7
8
Page 24
100 Microwave 1
The default time will be adjusted according to weight
Symbol
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Soup
500g
500
Microwave
19
800
Microwave
22
Noodles
300
300
Microwave
5
600
Microwave
8
200g
100
Microwave
2
200
Microwave
4
300
Microwave
5
400
Microwave
6
500
Microwave
7
600
Microwave
8
Bread
200g
100
Microwave
1
200
Microwave
2
300
Microwave
3
Symbol
Description
Display
The default time will be adjusted according to weight
Defa
weigh
Weight
Alternative
（g）
Function
Duration
(Minutes)
Milk
250g
250
Microwave 2
500
Microwave 4
Soup
500g
500
Microwave
19
800
Microwave
22
Noodles
300
300
Microwave
5
600
Microwave
8
200g
100
Microwave
2
200
Microwave
4
300
Microwave
5
400
Microwave
6
500
Microwave
7
600
Microwave
8
Bread
200g
100
Microwave
1
200
Microwave
2
300
Microwave
3
500g
100
Microwave
3
200
Microwave
5
300
Microwave
6
400
Microwave
7
500
Microwave
8
600
Microwave
9
700
Microwave
10
Symbol
Description
Display
200g
Fish
500g
Instruction manual CM110GM24
200 Microwave 2
300 Microwave 3
100 Microwave 3
200 Microwave 5
300 Microwave 6
400 Microwave 7
500 Microwave 8
600 Microwave 9
700 Microwave 10
800 Microwave 11
900 Microwave 12
1000 Microwave
Please keep this instruction manual for future reference
Page 25
200 Microwave 7
Meat
400
Microwave
10
500
Microwave
12
600
Microwave
14
500g
200
Microwave
7
300
Microwave
8
Meat
400
Microwave
10
500
Microwave
12
600
Microwave
14
800
Microwave
16
1000
Microwave
19
Chicken
1000g
200
Microwave + Grill
15
400 20
600 25
800 30
1000 32
1200 35
500g
200
Microwave
7
300
Microwave
8
300 Microwave 8
400 Microwave 10
500g
1000g
500 Microwave 12
600 Microwave 14
800 Microwave 16
100 Microwave 19
200 Microwave + Grill 15
400 Microwave + Grill 20
600 Microwave + Grill 25
800 Microwave + Grill 30
1000 Microwave + Grill
1200 Microwave + Grill
1400 Microwave + Grill
1600 Microwave + Grill
1800 Microwave + Grill
32
35
40
46
52
2000 Microwave + Grill
Please keep this instruction manual for future reference
Instruction manual CM110GM 25
56
Page 26
DEFROST TIME TABLE
The maximum weight for defrost is 2000g. The default defrost time will be
adjusted according to different weight selected.
WEIGHT
(GRAMS)
100 3 1100 22
200 5 1200 24
300 6 1300 26
400 8 1400 28
500 10 1500 30
600 12 1600 32
700 14 1700 34
800 16 1800 36
900 18 1900 38
1000 20 2000 40
TIME
(MINUTES)
WEIGHT
(GRAMS)
TIME
(MINUTES)
Instruction manual CM110GM26
Please keep this instruction manual for future reference
Page 27
CM108 / CM110
D
EMO MODE
CM108 / CM110
D
EMO MODE
EMO MODE
EMO MODE
CM108 / CM110
D
EMO MODE
DEMO MODE
TO TURN ON DEMO MODE:
Press the button to turn the oven on (in standby mode). Press and hold the button for 5
seconds. The alarm will beep 3 times, and will appear in the top right of the display to confirm
the oven has entered demo mode.
In demo mode, the normal operation of the cooling fan, circulation fan, and lighting work
normally, however all heating elements and other functions are disabled.
If the oven is turned off, it will remain in Demo mode when the over is turned back on.
TO TURN OFF DEMO MODE:
Press the button to enter standby mode, then press and hold the button for 5 seconds. The
alarm will beep 3 times, and the will disappear from the display to confirm the system has
exited Demo mode, and is ready for normal use.
Please keep this instruction manual for future reference
Instruction manual CM110GM 27
Page 28
CARE AND MAINTENANCE
IMPORTANT:
Unplug your oven before cleaning, or performing maintenance.
To extend the life of your microwave oven, it must be cleaned frequently, keeping
in mind the following:
DO NOT USE STEAM EQUIPMENT TO CLEAN THE APPLIANCE
» To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water
or other liquid or sprinkle water to clean the appliance.
» Don’t clean the appliance when it still hot! The inside and external surface of the oven should
preferably be cleaned by damp cloth when it is cooled down.
» Wash all accessories in hot soapy water or in a dishwasher, wipe dry with a paper or cloth
towel.
» If you use your oven for an extended period of time, condensation may form. Dry it using a soft
cloth.
» There is a seal surrounding the oven opening which guarantees its perfect functioning. Check
the condition of this seal on a regular basis. If necessary, clean it and avoid using abrasive
products or objects to do so. Should it become damaged, please contact Caple service. We
recommend you avoid using the oven until it has been repaired.
» Never line the oven bottom with aluminium foil, as the consequent accumulation of heat could
compromise the cooking and even damage the enamel.
» Clean the glass door using damp cloth and dry it with a soft cloth.
» Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since
they can scratch the surface, which may result in shattering of the glass.
Instruction manual CM110GM28
Please keep this instruction manual for future reference
Page 29
REMOVING THE OVEN DOOR
shown in figure 2.
door backwards and forward slightly);
the door again.
To make it easier to clean the inside of your oven, the oven door can be easily removed, by
proceeding as follows (fig. 11):
1. Open the door completely and lift the 2 levers “B” (fig.11-1);
2. Now, shutting the door slightly, you can lift it out by pulling out the hooks “A” as shown in
figure 2.
To reassemble the door:
1. With the door in a vertical position, insert the two hooks “A” into the slots;
2. Ensure that seat “D” is hooked perfectly onto the edge of the slot (move the oven door
backwards and forward slightly);
3. Keep the oven door open fully, unhook the 2 levers “B” downwards and then shut the
door again.
Fig.11-1 Fig.11-2
TROUBLESHOOTING .
The oven does not operate Check it is switched on at the mains.
The control panel is not working Check to see if the child lock is on.
The interior lamp does not illuminate Contact Caple service.
E2 error code appears on the screen Interior sensor error. Contact Caple service.
Please keep this instruction manual for future reference
There has been a power cut.
The time is not set.
If so, hold the lock key to turn it off.
Instruction manual CM110GM 29
Page 30
TECHNICAL DATA
BUILT-IN
COMBINATION
MICROWAVES
Model CM110GM
Rated Voltage 220- 240V
Rated Frequency 50Hz
Rated Grill Power 2550W
Rated Microwave Input Power 1500W
Combination Power 2550W
Microwave Rated Output Power 1000W
Volume 40L
Instruction manual CM110GM30
Please keep this instruction manual for future reference
Page 31
NOTES:
Please keep this instruction manual for future reference
Instruction manual CM110GM 31
Page 32
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
T: 0117 938 1900
E: service@caple.co.uk
www.caple.co.uk
Loading...