Caple C761GSS User Manual

Instruction Manual
Gas Hob
Model: C 761 G
GB
2
Installation Requirements................ ........................................................................3
Gas Installation ................ ......................................................................................4
Installation ...............................................................................................................5
How To Use Your Gas Hob ............................ ......................................................8
Your Guarantee ..................... ...............................................................................12
Thank you for buying your new CAPLE Gas Hob. To ensure that you get the best results from your new CAPLE Gas Hob, we strongly suggest that you read this instruction manual thoroughly before use. This manual contains installation advice, usage instructions and a cleaning guide, as well as other important facts about your CAPLE Gas Hob. If treated with care, your CAPLE Gas Hob should give you years of trouble-free cooking.
For Spare Parts, Technical Advice
or Product Service call the
CAPLE HELPLINE on 0870 241 1142
(Answerphone outside office hours)
Contents
The CE marking confirms that the appliance conforms to the following EU directives:
- safety requirements of the “Gas” Directive 90/396/EEC;
- safety requirements of EEC Directive “Low voltage” 73/23;
- protection requirements of EEC Directive “EMC” 89/336;
- requirements of EEC Directive 93/68. 3
Electrical Installation
This appliance must be connected by a qualified electrician using fixed wiring via a double pole isolating switch (fig. 1).
As the colours of the wires in the mains lead for the appliance, may not corre­spond with the coloured markings iden­tifying the terminals in your spur box, proceed as follows:
1) The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or coloured Green.
2) The wire which is coloured blue must be connected to the terminal marked N (Neutral), or coloured Black.
3) The wire which is coloured brown must be connected to the terminal marked L (Live), or coloured Red.
FUSE
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
USE A 3 AMP FUSE
ON
Fig. 1
WARNING!
ELECTRICITY CAN BE
EXTREMELY DANGEROUS.
THIS APPLIANCE MUST BE EARTH-
ED.
Installation Requirements
Technical Information
Total absorbed power 11.25 kW Double-ring burner 3.20 kW Rapid burner (1) 3.05 kW Rapid burner (2) 2.40 kW Semi rapid burner 1.60 kW Auxiliary burner 1.00 kW Voltage 230 V Single phase
Cat. I 2H - Class 3
4
Gas installation
This appliance should be fitted by a C.O.R.G.I. registered fitter. The installation must comply with Gas Safety (installation and use) Regulations
1994.
It is illegal to provide any assistance in the installation of gas appliance except to C.O.R.G.I registered installers.
Any C.O.R.G.I registered fitter requiring help must provide name, address and registration number. Information supplied will be validated before help is provided.
This appliance is predisposed and adjusted to operate with Natural Gas at 20 mbar.
After connecting to the mains, check that the couplings are correctly sealed, using soapy solution, but never a naked flame.
BURNERS
Auxiliary (A) 1,00 0,32 40 65* Semi-rapid (SR) 1,60 0,39 43 85* Rapid (R2) 2,40 0,58 55 110* Rapid (R1) 3,05 0,67 60 115 (.15*) Double-ring (DR) 3,20 0,77 62 125*
Nominal
input [kW]
Reduced
input [kW]
By-pass
[1/100 mm]
Ø injector
[1/100 mm]
Natural Gas - 20 mbar
* = Injector brand
INJECTORS TABLE
GB
Cat: I 2H
Gas Installation
If the gas tap becomes stiff, it is necessary to dismount it accurately clean it with gasoline and spread a bit of special grease resistant to high temperatures on it.
The operations must be executed by a qualified technician.
Lubrication of the gas taps
Loading...
+ 8 hidden pages