Cantek D1648-1TB User Manual

Stand Alone Digital Video Recorder

H.264 Realtime DVR

4, 8, 16 Channel Models

User’s Manual

V2.05-7099 This document contains preliminary information and is subject to change without notice.

FCC Compliance Statement

Notice to Users: This equipment has been tested and found to comply with the limits for a Class A digital device.

Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

The equipment complies with the requirement of FCC CFR 47 PART 15 SUBPART B, Class A.

Explanation of Graphical Symbols

This symbol indicates the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product.

This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Warnings

} Installation and servicing should be performed only by qualified and experienced personnel.

} Power off the DVR when connecting cameras, audio, or sensor cables.

} The manufacturer is not responsible for any damage caused by improper use of the product or failure to follow

instructions for the product.

} The manufacturer is not responsible for any problems caused by or resulting from the user physically opening

the DVR for examination or attempting to fix the unit.

} The manufacturer may not be held liable for any issues with the unit if the warranty seal is removed.

Cautions

} This product has multiple-rated voltages (110V and 220V). See installation instructions before connecting to the

power supply.

} This product uses a Lithium battery.

} To avoid any risk of explosion, do not replace the battery on the main board by anything other than a Lithium battery.

} Dispose of used batteries according to the manufacturer’s instructions.

} This equipment and all communication wirings are intended for indoor use only.

} To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.

WEEE(Waste Electrical and Electronic Equipment)

Customers in European Union countries are advised to dispose this product, at the end of its useful life, as per applicable local laws, regulations and procedures.

Important Safeguards

1. Read Instructions

All safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Cleaning

Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

4. Attachments

Never add any attachments and/or equipment without manufacturer approval as such additions may result in the risk of fire, electric shock, or other personal injury.

5. Water and/or Moisture

Do not use this equipment near water or in contact with water.

6. Accessories

Do not place this equipment on an unstable cart, stand or table. The equipment may fall, causing serious injury to a child or adult and serious damage to the equipment. Wall or shelf mounting should follow the manufacturer’s instructions and should use a mounting kit approved by the manufacturer.

Move this equipment and cart combination with care. Quick stops, excessive force and uneven surfaces may cause the equipment and cart combination to overturn.

7. Power Sources

This equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your distributor or local power company.

8. Power Cords

Operator or installer must remove power, BNC, alarm and other connections before moving the equipment.

9. Lightning

For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment due to lightning and power-line surges.

10. Overloading

Do not overload wall outlets and extension cords to avoid the risk of fire or electric shock.

11. Objects and Liquids

Never push objects of any kind through openings of this equipment as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the equipment.

12. Servicing

Do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel.

13. Damage Requiring Service

Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions:

y When the power-supply cord or the plug has been damaged y If liquid is spilled or objects have fallen into the equipment y If the equipment has been exposed to rain or water y If the equipment does not operate normally by following the operating instructions, adjust only those controls that are

covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the equipment to its normal operation.

y If the equipment has been dropped or damaged the cabinet. y When the equipment exhibits a distinct change in performance—this indicates a need for service.

14. Replacement Parts

When replacement parts are required, ensure the service technician uses replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

15. Safety Check

Upon completion of any service or repairs to this equipment, ask the service technician to perform safety checks to determine that the equipment is in proper operating condition.

16. Field Installation

This installation should be made by a qualified service person and should conform to all local codes.

17. Correct Batteries

WARNING

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

18. Operating Temperature

An operating temperature range is specified so that the customer and installer may determine a suitable operating environment for the equipment.

19. Elevated Operating Ambient Temperature

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the specified operating temperature range.

20. Reduced Air Flow

Installation of the equipment in the rack should be such that the amount of airflow required for safe operation of the equipment is not compromised.

21. Mechanical Loading

Mounting of the equipment in the rack should be such that a hazardous condition is not caused by uneven mechanical loading.

22. Circuit Overloading

Consideration should be given to connection of the equipment to supply circuit and the effect that overloading of circuits might have on over-current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

23. Reliable Earthing (Grounding)

Reliable grounding of rack mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (for example, use of power strips).

THE LIST OF CONFIGURATION

A Type

4CH

8CH

16CH

B Type

DVR Set

4CH

8CH

16CH

CD (Software/Manual)

Remote Controller

Manual

Screws

HDD Brackets (Optional)

Data Cable (SATA Cable)

Power Cable

Operation Precautions

} Power Off

y Do not turn DVR off, or plug off the power adapter while DVR is in operation (record/playback). Otherwise, it may cause

permanent damage to the equipment. Please click ( ) SETUP>SYSTEM>Shutdown sequentially and then remove the power after DVR is shutdown completely. It is safe to wait for 5 seconds before turning the power on again.

y Do not turn DVR off, or plug off the power adapter while External storage

external hard disk and the like) in use. Otherwise, it may cause permanent damage to the equipment. Make sure that the power switch is in the “ON” position until data storage is completed. Please be aware that removing the storage device cause the same damage to the equipment.

y Do not turn DVR off, or plug off the power adapter during the format of the hard disk

damage to the equipment. Make sure that the power switch is in the “ON” position until the formatting of the disk is completed.

} HDD Installation/Addition/Moving/Replacement/Removal

y For installation/addition/replacement/Removal of HDD (DVD-RW), make sure that DVR is turned off. Otherwise, it may

cause permanent damage to the HDD (DVD-RW).

y When you want to power DVR off, please click ( ) SETUP>SYSTEM>Shutdown sequentially and then remove the

power after DVR is shut down completely.

y Installation/Addition/Moving/Replacement: You should start ‘HDD initialization’ including formatting. Otherwise, DVR

won’t recognize the hard disk and may begin to function abnormally. Please follow the below procedure for ‘HDD initialization’.

① (Date/Time setup) Set up the current date and time (SETUP>SYSTEM>Admin>Date/Time). ② (Initialization of system setup) All setup values are restored to original factory default settings.

(SETUP>SYSTEM>Information>Status>Setup>Default).

③ (HDD format) HDD format is done by SETUP>SYSTEM>Admin>Storage>Format. If there are more than two HDDs,

each must be formatted, separately. When the format is completed, DVR will auto-reboot.

y Removal: Follow the Remove procedure even when a pre-installed hard disk has been removed.

SETUP>SYSTEM>Admin>Storage>Format, click ( ) ‘Removed’ item under the discrete Format headings of a corresponding HDD to discard ‘HDD’ item. When the Remove procedure is completed, DVR will auto-reboot.

} Date/Time Change

y Any change in Date/Time is immediately applied onto live video (LIVE), but the date/time when the recording was done

are not changed.

y Make sure that you reboot DVR after adjusting the Date/Time. y Also, do not forget to execute SETUP>SYSTEM>Shutdown in sequence before reboot.

} Upgrade

y Do not upgrade until you install a hard disk drive. Make sure you upgrade when the hard disk drive is in proper operation.

} Using a Mouse

y Left mouse button: have the same function as Enter ( ) on the Front panel of DVR y Central button (wheel): have the same function as Search key on the Front panel of DVR(display search menu) y Right mouse button: display a number of ‘Function keys’ (please see ‘Input Device and Screen Icons>Using a mouse’

in this manual)

} PLAY/PAUSE Key

y Press the PLAY/PAUSE key to one-touch playback on the viewing screen (playback the recorded video from the last

one minute).

y Every time you press the PLAY/PAUSE key during playback mode, it is changed to ‘1X PLAY’ and ‘PAUSE’. The

displayed sign on the screen also changes from

y If you want to change mode (1X PLAY, REW, FF, BACKWARD, FORWARD) during playback, always press the

PLAY/PAUSE key first (please see if the sign II is shown on the screen).

y Press the PLAY/PAUSE key to back up. Make sure that the backup is done in ‘PAUSE’ mode.

to II.

} Camera Title

Camera Title displayed in Record and Playback modes of DVR is set to CAM1 ~CAM16. Registering camera title in setup menu (DEVICES>Camera/PTZ>Title) is to make every setup process easier.

device (e.g., USB memory stick, removable

. Otherwise, it may cause permanent

Table of Contents

SERVER

1. Product Features ---------------------------------------- 8

1.1 Unpacking ------------------------------------------------------ 8

1.2 Service ---------------------------------------------------------- 8

1.3 System Connection Diagram------------------------------ 8

2. Installation -------------------------------------------------- 10

2.1 Hard disk and DVD-RW Installation ------------------- 10

2.1.1 SATA Port ----------------------------------------------------- 10

2.1.2 No Jumper Designation ----------------------------------- 10

2.1.3 HDD Installation --------------------------------------------- 10

2.1.4 DVD-RW Installation --------------------------------------- 11

2.2 Connector Wiring-------------------------------------------- 11

2.2.1 Video In/Out Connections--------------------------------- 11

2.2.2 Monitor Connections --------------------------------------- 11

(Video Out, VGA, SPOT)

2.2.3 Audio Connections ----------------------------------------- 11

2.2.4 TCP/IP(Ethernet) Connections -------------------------- 11

2.2.5 Alarm Connections ----------------------------------------- 11

2.2.6 RS-485/422 Connections --------------------------------- 11

2.2.7 USB Connections ------------------------------------------- 11

2.2.8 Factory Reset Switch -------------------------------------- 12

2.2.9 Power Supply Connections ------------------------------ 12

2.2.10 Connection Guideline -------------------------------------- 12

3. Input Device and Screen Icons ------------------ 13

3.1 Keys and LEDs ---------------------------------------------- 13

3.2 Camera Select Keys for 4/8 channel DVR ----------- 14

3.3 Front Panel ---------------------------------------------------- 14

3.4 Using a Remote Control ----------------------------------- 15

3.5 Using a Mouse ----------------------------------------------- 15

3.6 Screen Icons -------------------------------------------------- 16

4. Setup ---------------------------------------------------------- 17

4.1 Login/Logout ------------------------------------------------- 17

4.2 SYSTEM ----------------------------------------------------- 18

4.2.1 Information ----------------------------------------------------- 18

Status Version Record

4.2.2 Admin --------------------------------------------------------- 21

Date/Time NTP Storage

4.2.3 Account --------------------------------------------------------- 24

New Group Login Settings New User

4.2.4 System Log ---------------------------------------------------- 26

4.2.5 Exit --------------------------------------------------------------- 27

4.2.6 Shutdown ----------------------------------------------------- 27

4.3 DISPLAY ----------------------------------------------------- 27

4.3.1 OSD ------------------------------------------------------------- 27

4.3.2 Main Monitor -------------------------------------------------- 28

Full Seq Quad Seq X9 Seq

4.3.3 Spot Monitor ------------------------------------------------- 29

4.3.4 Spot Monitor Control on Display Mode --------------- 29

4.4 DEVICES ------------------------------------------------------ 30

4.4.1 Network --------------------------------------------------------- 30

LAN DDNS Port Notification

4.4.2 Camera/PTZ-------------------------------------------------- 33

4.4.3 Audio ------------------------------------------------------------ 34

4.4.4 Alarm In -------------------------------------------------------- 34

4.4.5 Alarm Out ------------------------------------------------------ 34

4.4.6 Serial In --------------------------------------------------------- 35

4.5 RECORD ---------------------------------------------------- 35

4.5.1 Settings -------------------------------------------------------- 35

Continuous Event Emergency

4.5.2 Schedule ------------------------------------------------------- 37

4.5.3 Pre Alarm ------------------------------------------------------ 38

4.5.4 Motion Detection -------------------------------------------- 38

4.5.5 Holiday --------------------------------------------------------- 39

4.6 LINK ----------------------------------------------------------- 40

4.6.1 Alarm In -------------------------------------------------------- 40

4.6.2 Motion Event ------------------------------------------------- 41

4.6.3 Video Loss ---------------------------------------------------- 41

4.6.4 System Event ------------------------------------------------ 42

4.6.5 Popup Link --------------------------------------------------- 43

5. Operation Instruction -------------------------------- 44

5.1 Viewing---------------------------------------------------------- 44

5.1.1 First Image ---------------------------------------------------- 44

5.1.2 View Formats ----------------------------------------------- 44

5.1.3 Digital Zoom -------------------------------------------------- 45

5.1.4 Freeze Live Image------------------------------------------ 45

5.1.5 Pan/Tilt Control----------------------------------------------- 45

5.1.6 System Log---------------------------------------------------- 46

5.1.7 Key Lock------------------------------------------------------- 46

5.1.8

5.2 Search --------------------------------------------------------- 47

5.2.1 Date/Time Search ------------------------------------------ 47

5.2.2 Calendar Search -------------------------------------------- 47

5.2.3 Event Search ------------------------------------------------- 48

5.3 Playback------------------------------------------------------- 49

5.4 One-touch Playback---------------------------------------- 50

5.5 Archive --------------------------------------------------------- 50

5.6 Color Control and Position -------------------------------- 51

5.7 Alarm Out Control ------------------------------------------ 52

Emergency Recording------------------------------------- 47

CMS

6. Program Installation ----------------------------------- 54

6.1 System Recommendation--------------------------------- 54

6.2 Program Installation Method------------------------------ 54

6.3 Login------------------------------------------------------------- 55

7. Function and Instructions ------------------------- 56

8. Watch Mode ----------------------------------------------- 57

8.1 Login Screen -------------------------------------------------- 57

8.2 Local Setting -------------------------------------------------- 57

8.2.1 System Setup ------------------------------------------------ 57

8.2.2 Remote Site --------------------------------------------------- 58

8.3 Live Video ----------------------------------------------------- 60

8.3.1 Network Connect ------------------------------------------- 60

8.3.2 Watch Mode -------------------------------------------------- 61

8.3.3 Multi Screen -------------------------------------------------- 62

8.3.4 Screen Color Adjustment --------------------------------- 62

8.3.5 Audio ----------------------------------------------------------- 62

8.3.6 System LOG ------------------------------------------------- 62

8.3.7 Alarm Out ----------------------------------------------------- 63

8.3.8 One Touch Recording ------------------------------------- 63

8.4 PTZ Control --------------------------------------------------- 63

8.5 Health Check ------------------------------------------------- 64

8.5.1 Camera Connection and Operating Status ---------- 65

8.5.2 HDD Connection and Its Operating Status ----------- 65

8.5.3 Recording Status -------------------------------------------- 65

8.5.4 Motion Recording Status ---------------------------------- 65

8.5.5 Alarm In Connection and Operating Status ---------- 65

8.5.6 Alarm Out Connection and Operating Status ------- 65

8.6 Remote Setting----------------------------------------------- 65

9. Search Mode ---------------------------------------------- 67

9.1 Search Screen ----------------------------------------------- 67

9.2 Remote Search --------------------------------------------- 67

9.3 Local Search ------------------------------------------------- 68

9.4 Event Search ------------------------------------------------- 68

9.5 Playback ------------------------------------------------------- 69

9.5.1 Playback Control Button ----------------------------------- 69

9.5.2 Print ------------------------------------------------------------- 69

9.5.3 Save ------------------------------------------------------------ 70

9.5.4 Archive---------------------------------------------------------- 70

10. Others --------------------------------------------------------- 72

10.1 Viewer ----------------------------------------------------------- 72

10.2 E Map ------------------------------------------------------ -72

10.3 Watermark Check System----------------------------- 73

10.4 Estimator ------------------------------------------------ -- 74

Keyboard Controller

11.1 Keyboard Controller ----------------------------------------- 76

11.2 PTZ/DVR Control Mode ---------------------------------- 76

11.2.1 PTZ Control Mode ------------------------------------------ 76

11.2.2 DVR Control Mode ----------------------------------------- 77

11.3 Keyboard Controller Setting ----------------------------- 77

11.4 Q/A -------------------------------------------------------------- 78

11.4.1 When a Key dose not Work after Setup --------------- 78

11.4.2 When Tx Blinks Continually on the LED Window-- 78

11.5 Keyboard System Connection --------------------------- 79

11.6 Consideration ------------------------------------------------- 79

11.7 Display Channel Change --------------------------------- 79

11.8 System Configuration Diagram -------------------------- 80

11.8.1 Configuration Diagram Ⅰ---------------------------------- 80

11.8.2 Configuration Diagram Ⅱ --------------------------------- 81

11.8.3 Configuration Diagram Ⅲ --------------------------------- 81

Serial ln

12.1 Usage of Serial-In Function ------------------------------ 83

12.2 Connection method in each series --------------------- 83

12.3 Connection Diagram ---------------------------------------- 83

12.4 Link -------------------------------------------------------------- 84

12.4.1 Link Setup ----------------------------------------------------- 84

12.4.2 Schedule Setup ---------------------------------------------- 85

12.5 Setup ------------------------------------------------------------ 85

12.5.1 Title -------------------------------------------------------------- 85

12.5.2 Port Setting ---------------------------------------------------- 86

12.5.3 OSD Display -------------------------------------------------- 86

12.5.4 Pattern Setting ----------------------------------------------- 86

12.6 Search ---------------------------------------------------------- 89

CMS Web Client

13.1 Setup and Login ------------------------------------------- 91

13.2 Live Display ------------------------------------------------- 91

13.3 Playback Screen ------------------------------------------- 92

Mobile CMS

14.1 Setup and Login ------------------------------------------- 95

14.2 Installation --------------------------------------------------- 95

14.3 Site Configuration ----------------------------------------- 97

14.4 Connect ------------------------------------------------------ 99

14.5 Uninstall ------------------------------------------------------- 99

1. Product Features

1.1 Unpacking

y This equipment is an electronic appliance, so it should be handled with special care. y After unpacking, please check if all the following items are included.

- DVR Main body

- A Type Power Supply Adapter (DC 12V, 3.33A) and Power Supply Cable

- B Type Power Supply Adapter (DC 12V, 5A) and Power Supply Cable

- Remote Control With 2 AAA batteries

- Installation CD (CMS Software & User’s Manual)

1.2 Service

y If there is any problem in the product, please refer servicing to a supplier or a distributor with qualified service personnel.

1.3 System Connection Diagram

A Type - 4 / 8 / 16 Channel Series DVR

B Type - 4 / 8 / 16 Channel Series DVR

2. Installation

2.1 Hard disk and DVD-RW Installation

2.1.1 SATA Port

y Main substrate of this DVR has three SATA ports: they are indicated as SATA 1,2 and SATA 3.( A Type )

Main substrate of this DVR has four SATA ports: they are indicated as SATA 1,2 and SATA 3,4.( B Type )

y Up to two SATA devices (hard disk and DVD-RW) are connected in Serial to the SATA ports, but the devices must be

connected correct SATA port.

y Please mount DVD-RW at the SATA 3 port.( A Type DVR) Please mount DVD-RW at the SATA 4 port.( B Type DVR) y Refer to below table to mount a hard disk and DVD-RW.

A Type

HDD DVD-RW 1 2 3

A Type 4/8/16

Channel DVR

Storage SATA 1,2 Port SATA 3 Port

1 1

2 1

HDD ---- DVD-RW

HDD HDD DVD-RW

B Type

HDD DVD-RW 1 2 3 4

B Type 4/8/16

Channel DVR

Storage SATA 1,2 Port SATA 3,4 Port

1 1

2 1

3 1

4 0

HDD ---- ---- DVD-RW

HDD HDD ---- DVD-RW

HDD HDD HDD DVD-RW

HDD HDD HDD HDD

2.1.2 No Jumper Designation

y SATA device does not use jumper. You only need to connect SATA device to SATA port according to HDD/ DVD-RW you

have. A connector for designation is located between the 7-pin SATA connector and the 15-pin Power connector.

2.1.3 HDD Installation

y Securely fix a hard disk by using bracket and screws provided herewith. y Please do not use any different hard disk cables (data cable and power supply cable) other than ones we provide.

Otherwise, it may cause damage to the hard disk.

CAUTION

Install hard disk after DVR power is off. Otherwise, it may cause permanent damage to the hard disk. To turn off DVR, please click ( ) SETUP>SYSTEM>Shutdown. Also, wait for 5 seconds before plugging in power supply again.

CAUTION

y For installation/addition/replacement/Removal of HDD (DVD-RW), make sure that DVR is turned off. Otherwise, it may cause

permanent damage to the HDD (DVD-RW).

y Installation/Addition/Moving/Replacement: You should start ‘HDD initialization’ including formatting. Otherwise, DVR won’t

recognize the hard disk and may begin to function abnormally. Please follow the below procedure for ‘HDD initialization’.

① (Date/Time setup) Set up the current date and time (SETUP>SYSTEM>Admin>Date/Time) ② (Initialization of system setup) All values in setup are restored to factory default settings

(SETUP>SYSTEM>Information>Status>Setup>Default).

③ (HDD format) HDD format is done by SETUP>SYSTEM>Admin>Storage>Format. If there are more than two HDDs, each must

be formatted, separately. When the format is completed, DVR will auto-reboot.

y Removal: Follow the Remove procedure even when a pre-installed hard disk has been removed. In

2.1.4 DVD-RW Installation

y Securely fix DVD-RW by using bracket and screws provided herewith. y Please do not use any different DVD-RW cables (data cable and power supply cable) other than the ones we provide.

Otherwise, it may cause damage to the DVD-RW.

y Only one DVD-RW can be used. Mount it at the SATA 3 port. (A Type DVR) Only one DVD-RW can be used. Mount it at the SATA 4 port. (B Type DVR)

CAUTION

Install DVD-RW hard disk after DVR power is off. Otherwise, it may cause permanent damage to the hard disk. To turn off DVR, please click ( ) SETUP>SYSTEM>Shutdown. Also, wait for 5 seconds before plugging in power supply again.

2.2 Connector Wiring

2.2.1 Video-In/Out Connections

y Connect a camera to ‘VIDEO IN’. y If you want to link camera input to another device, please connect the camera to ‘LOOP OUT’. y Assure the ‘VIDEO IN’ and ‘LOOP OUT’ are connected properly, not oppositely.

(NOTE) LOOP OUT function use Only B Type model.

2.2.2 Monitor Connections (Video Out, VGA, SPOT)

y Use with CCTV monitor and computer monitor. Please connect the CCTV monitor to ‘VIDEO OUT’, the computer monitor to

‘VGA’, respectively. If necessary, you may connect another CCTV monitor to ‘SPOT’.

2.2.3 Audio Connections

y Connect an audio device to ‘AUDIO IN’ and a speaker system to ‘AUDIO OUT’. Please use a speaker system with volume

adjustable.

2.2.4 TCP/IP(Ethernet) Connections

y Connect to ‘ETHERNET’ connector with the LAN cable. y When connect to Internet, use an ordinary LAN cable (Non-cross cable). However, when connect directly to your PC,

please use only ‘Crossover cable’.

2.2.5 Alarm Connections

y Connect Alarm Input (Sensor) to ‘AI 1~AI 4(AI 16)’ connectors and connect Sensor Common to ‘G’ connector. y Connect Alarm Output (buzzer, siren, etc.) to ‘AO 1~AO 4(AO 16)’ connectors and connect Common to ‘G’ connector. y Connect Pan/Tilt receiver (or Pan/Tilt camera) to ‘RS-485/422’ connector. Please observe proper (+) and (-) polarity.

2.2.6 RS-485/422 Connections

y PTZ Camera connector y Please use TX+, TX-, RX+ and RX- terminals.

2.2.7 USB Connections

y There are four identical USB (2.0) ports in front and in rear. You may connect an external hard disk, an external USB, DVD-

RW and a USB memory stick to the USB ports.

y When you use an external hard disk, please assure the connecting cable is not longer than 1.8m (6 ft).

2.2.8 Factory Reset Switch

y Reset the switch to restore all setup values of menus to factory default settings. You may also use this switch to initialize

System Log file.

y The switch is located in a pin hole on the left-hand side of the USB connector of the back panel. y Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until you feel the switch has clicked.

CAUTION

PRESS FACTORY RESET SWITCH ONLY IN LIVE MODE. NEVER PRESS IN SETUP MODE.

2.2.9 Power Supply Connections

y A Type: Plug the power supply adapter (DC 12V, 3.33A) which include in this product to ’DC12V’ connector and plug

another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC). Please do not use any different power supply adapter because it may cause the DVR to malfunction.

y B Type: Plug the power supply adapter (DC 12V, 5A) which include in this product to ’DC12V’ connector and plug another

side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC). Please do not use any different power supply adapter because it may cause the DVR to malfunction.

2.2.10 Connections Guideline

y Video Out Connector: If only the monitor is connected to VIDEO OUT connector, please set the impedance switch on the

rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images. If you want to connect another device (e.g., a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to HIGH Z (High Impedance) and set the last device to 75 ohms.

y Alarm Input Connector: Do not input any type of voltage to the AI 1~AI 4 (AI 16) connectors.

3. Input Device and Screen Icons

3.1 Keys and LEDs

KEYS PTZ KEY Operating mode Setup mode

▲, ▼, ◄, ►

• Control Pan/Tilt rotation of up/down/left/right in PTZ mode

• Up/Down/Left/Right on screen cursor control

1 ~ 8

1 ~ 10

DISPLAY

SEQUENCE

ARCHIVE

FREEZE

AUDIO/ESC

EMERGENCY

EVENT

• Camera select keys : (4/8 channel DVR)

• Camera select keys : (16 channel DVR)

• Select sequence mode

• Channel sequence mode on/off (Main Monitor)

• Video search mode on/off

• Copy video data into the external storage device

• Screen freeze mode on/off

• Audio on/off (Viewing/Playback)

• Select audio channel: Press AUDIO key and then channel key

• ESC

• Emergency recording on/off

• System Log display on/off

PTZ

REW

BACKWARD

PLAY/PAUSE

FORWORD

FORWARD

Power LED (Red) HDD LED (Green) Network LED

(Yellow)

• Pan/Tilt control mode on/off

• Enter the Main Menu (Setup mode)

• Fast reverse playback (changes to x16, x32 with each press)

• Zoom Out in PTZ mode

• Frame-by-frame reverse still image playback

• Zoom In in PTZ mode

• Viewing mode: One-touch playback (playback the recorded video from the last one minute)

• Playback mode: 1X PLAY/PAUSE

• Focus Near in PTZ mode

• Focus Far in PTZ mode

• Exit Window without saving

• Fast forward playback (changes to x16, x32 with each press)

• Save Preset in PTZ mode

• Frame-by-frame forward still image playback

• Go to in PTZ mode

• Light off: DVR off

• Light on: DVR on

• Light off: Stop recording

• Blink : Recording/Playback modes (HDD Access), Archive in operation

• Light off: failed to connect to Ethernet

• Blink: Connected to Ethernet

3.2 Camera Select Keys for 16 channel DVR.

A Type model

y Below shows how to select camera channel for 4 channel DVR

– Select Camera No. 1~4: press key and use 1~4 key

y Below shows how to select camera channel for 8 channel DVR

– Select Camera No. 1~8: press key and use 1~8 key

y Below shows how to select camera channel for 16 channel DVR

– Select Camera No. 1~9: press key and use 1~9 key

– Select Camera No. 10~16: press key and use , 1~6 key

B Type model

y Below shows how to select camera channel for 4/8/16channel DVR y Below shows how to select camera channel for 4 channel DVR

– Select Camera No. 1~4

y Below shows how to select camera channel for 8 channel DVR

– Select Camera No. 1~8

y Below shows how to select camera channel for 16 channel DVR

– Select Camera No. 1~10: use 1~10 direction key – Select Camera No. 11~16: press key and use 1~6 direction key

3.3 Front Panel

A Type model

4 Channel DVR

8 Channel DVR

16 Channel DVR

B Type model

4 Channel DVR

8 Channel DVR

16 Channel DVR

3.4 Using a Remote Controller

y Usage of a remote controller is same as the front panel keys. y Follow the procedure below when you use the remote controller for multi DVRs.

① Check System ID (e.g., between 1 and 999) of the DVR you wish to use

(SETUP>SYSTEM>Information>Status>System ID).

② Holding up the remote controller to face towards the DVR and press the System ID numbers one by one, while pressing

ID button on the remote controller. Note that the System ID is a 3-digit number. Button ‘10’ functions the same as ‘0’.

(e.g.: If System ID is 3, you should press 10>10>3 buttons in sequence while pressing the ID button)

3.5 Using a Mouse

y Mouse provides an easier access to adjustment. Refer to below for proper use. y Left mouse button functions the same as Enter ( ) key on the front panel of DVR. y Right mouse button displays the following “Function keys” on your screen. y Click Search menu at “Function Keys” the same as Search key on the front panel of DVR. Press the button, then the

Search menu will appear on your screen.

Name of

Key

Display

Sequence

Spot

Zoom

Freeze

PIP

PTZ

Function

Same as panel key

Name of

Key

Event

Setup

Emergency

Shutdown

Cancel

Function

Same as panel key (indicate System Log)

One-touch playback (same function with (PLAY/PAUSE)

Same as panel key

Pre-step before Power off (SETUP>SYSTEM>Shutdown)

Cancel Function key menu

3.6 Screen Icons

Icon Description Icon Description

Continuous recording mode

Event recording mode

(Alarm In/Motion)

In recording

PTZ registration / PTZ mode

Remote Controller

Setup in HDD No Overwrite mode

(HDD Full)

In Audio recording

CMS access indication/ No. of accesses

(up to 4)

In channel sequencing

Lock

Setup in HDD Overwrite mode

Setup in HDD No Overwrite mode

(recording)

4. Setup

4.1 Login/Logout

y At the default setting of DVR, you have to input the password to enter the set up menu. y Please press SETUP key to enter the setup menu and the following screen will appear.

y In order to use all functions and privileges, login is as ID: admin. y Default Password is “1111”. y At Setup>System>Account, click Login Settings button and you can set for Login window. When you use Setup,

Archiving,Search, Shutdown, Network menu, you can limit general users’ approach by the login window (See 4.2.3 Account).

y At Setup>System>Account menu, if you add a user, that user’s ID will appear and you can login as its general ID. y After login successfully, following screen will appear:

y Recording continues during setup. y Main menu consists of 5 sub menus.

(SYSTEM / DISPLAY / DEVICES / RECORD / LINK)

y There is no factory default in the case of passwords. y To escape from the setup menu, please click( ) on SYSTEM>Exit on the screen. Then, the following dialogue box will

appear.

y Please choose ‘OK’ to log out. y You may select the Main menu with

submenu under the Main menu.

, direction keys or mouse click. Please click ( ) the submenu to choose a

(NOTE) Press AUDIO/ESC in the setup screen, start operation alike CANCLE (ESC). It will not operate live or playback mode but only in the setup menu.

4.2 SYSTEM

4.2.1 Information

y Please click ( ) SYSTEM>Information and the following screen will appear.

Status

Site Description

y Decide name of DVR. y Please click ( ) keyboard icon on Site Description frame and the following virtual keyboard will appear.

y Please click ( ) desired letters (characters) on the virtual keyboard to input.

①

②

y Please choose ‘OK’ to confirm the input and choose ‘Cancel’ to cancel.

System ID

y Control DVRs by one remote controller by setting DVR IDs. y Please click ( ) ▲, ▼ direction keys on the right-hand side of the System ID frame to set the ID of DVR. Take any whole

number between 1 and 255.

y While pressing (+) or (-) button, the System ID value increases or decreases by 10 units.

Language y Please click ( ) Language frame to choose desired language and press ( ) key again.

Setup

y Default: Click ( ) Default frame to restore all setup values of menus to factory default settings. Please note that System

Log is not initialized.

Use to erase one character every time.

Use to erase the whole sentence.

(NOTE) This has a different function from Factory Reset Switch on the back panel of DVR in that System Log is not initialized.

y Import: Copy the Menu setup stored in USB memory stick into DVR. Please plug in the memory stick and then click ( )

Import.

y Export: Store the Menu setup of DVR in USB memory stick. Please plug in the memory stick and then click ( ) Export. y When you are working on Default, Import, Export, a message box will ask the progress and click the confirmation icon, then

a message box will show whether its success or failure.

System Log

y Export: Store the System Log contents in USB memory stick. Please plug in the memory stick and then click ( ) Export. y When you are working on Default, Import, Export, a message box will ask the progress and click the confirmation icon, then

a message box will show its success or failure.

Version

y When you complete Status data input, please click ( ) Version and the following screen will appear.

Version Upgrade

y You may upgrade DVR software. y Please follow the Upgrade procedure below.

① Plug USB memory stick having upgrade file into DVR. ② Click ( ) Load frame. Then, software version stored in the USB will appear on the left-hand side. ③ Click ( ) Start frame to start the upgrade. ④ When the upgrade is completed, a dialogue box pops up. Please choose ‘OK’ and DVR will auto-reboot.

CAUTION

DO NOT UPGRADE UNTIL YOU INSTALL A HARD DISK DRIVE. MAKE SURE YOU UPGRADE WHEN HDD IS IN PROPER OPERATION.

CAUTION

PLUGGING OUT USB DEVICE OR FORCED POWER-OFF MAY CAUSE PERMANENT DAMAGE.

Record

y When you complete Version input, please click ( ) Record. Then, the following screen will appear.

y The screen shows start time and end time of recorded data.

Overwrite Setting

y Click( ) Overwrite Setting button and the following screen will appear.

y You may set for beeping or notifying messages that notify the used percentage of disk. y Check Disk Overwrite and you may activate the overwrite function.

This function makes restart the recording from the beginning when the HDD is full. The previous recorded data will be

erased from the first one. Following icon will display in bottom of live mode

① Uncheck (□) Disk Overwrite, recording will stop automatically when the HDD is full.

② At the Overwrite mode, when HDD capacity is full,

icon will appear and the recording is going on, will appear.

③ If you change this setting, the warning message will appear. Then click ( ) “confirmation” button and you may change

the setting.

y If you check (5) Disk full notify item, the warning message will appear as the used amount of disk.

① Used

You may set the certain value of HDD usage for notification. It will notify at that point. The values are from 50 ~ 100%.

② Alarm-Out

The Alarm-out will happen at the used amount of HDD which is specified at Used.

③ Beep

Check (5), the warning sound will happen at the used amount of HDD which is specified at Used.

④ Blink Message

Check (5), the warning message “Disk Used(xx%)!” will appear on the OSD.

(NOTE) Notify setting does not affect saving the recorded data. It only gives notification and keep recording until hard disk is full.

(NOTE) For more specific setting about Alarm-out, use Setup>DEVICES>Alarm Out.

Clear All Data

y Use to delete or purge all normal recorded data from database. Please follow the procedure below.

① Click ( ) Clear All Data frame. ② When a dialogue box asking “Remove All Data?” shows, choose ‘OK’. ③ Then, Progress window will appear and the process starts. ④ When all data are deleted, a dialogue box asking “Are you sure to remove log?” will pop up. ⑤ Choose ‘OK’ to delete all the recorded data as well as System Log.

(NOTE) This might take a while to completely delete all data. In case of 80GB HDD for example, it takes about 90 seconds.

y When you finish all the necessary inputs to SYSTEM menu, please click ( ) ‘OK’ on the bottom to go back to SETUP

screen.

4.2.2 Admin

y Please click ( ) SYSTEM>Admin and the following screen will appear.

Date/Time

Date

y This menu will allow you to adjust the settings. y Please follow the procedure below for time adjustment.

① Click ( ) items (Y, M, D) you want to change. A designated item will be highlighted in a box (Y: Year, M: Month and D:

Date).

② Adjust the number by clicking ( ) ▲, ▼ buttons on the right-hand side. ③ Repeat the same procedure to change Y, M and D.

Time

y This menu will allow you to adjust the current time. The adjustment procedure is same as of Date.

CAUTION

IF ADJUSTED DATE/TIME IS PRIOR TO RECORDED DATA, DATA AFTER NEW DATE/TIME MAY BE ERASED.

CAUTION

ANY CHANGE IN DATE/TIME IS IMMEDIATELY APPLIED ON VIEWING SCREEN (LIVE), BUT THE DATE/TIME WHEN THE RECORDING WAS DONE ARE NOT CHANGED. MAKE SURE TO REBOOT DVR AFTER CHANGING THE DATE/TIME. DO NOT FORGET TO EXECUTE SHUTDOWN (SYSTEM>Shutdown) BEFORE REBOOT.

Time Zone

y Please click ( ) Time Zone frame to see the list of nations and choose one. y Click ( ) a check box next to Use Daylight Saving Time. When you live in a region to observe DST, please check it (i.e. 5). y If DST is observed, please click ( ) Period and the following screen will appear.

y Adjust the dates of beginning (Begin) and end (End) of DST by ‘Month/Week/Weekday’. y Click ( ) the numbers in ‘Month/Week/Weekday’ for adjustment. y Choose ‘OK’ to confirm the setting.

Date Format

y Set date indication format. Please click ( ) Date Format frame to select a format you like from the list.

Time Format y Set time indication format. Please click ( ) Time Format frame to select a format you like from the list.

NTP

y When you complete Date/Time input, please click ( ) NTP and the following screen will appear.

y This menu is for accurate setting of time of day clock in DVR. y You may check 5 only one of Run as Server and Use NTP.

– Run as Server: NPT cannot be used in a non-networked environment (Intranet environment). In this case, DVR with

Run as Server functions as Time Server.

– Use NTP: Connect to Internet to synchronize DVR clock with Network Time Server’s clock.

NTP Server y Click ( ) keyboard icon in NTP Server frame and the virtual keyboard will appear. Input IP address of NTP server.

(NOTE) Currently used NTP is administered by pool.ntp.org and its IP address is 65.23.154.62. However, users are allowed to use IP address

of any NTP site.

Interval y Set clock-update-interval from NTP Server. Normally, you can adjust 1 hour up to 24 hours.

System Clock y Display DVR clock.

Server Clock

y Display NTP Server’s clock if Internet is not connected to Server Clock. If not, please click ( ) Connect button. y When Server Clock is displayed, please click ( ) Sync button to synchronize NTP Server’s clock with DVR clock. y Choose ‘OK’ to confirm the clock synchronization.

Storage

y When you complete NTP input, please click ( ) save and the following screen will appear. y Set S.M.A.R.T. (Self-Monitoring Analysis and Reporting Technology) function for HDD format and auto-display of HDD

information. DVD-RW is not shown here.

y Four rows will show as follows:

– 1: SATA 1 Port – 2: SATA 2 Port – 3: SATA 3 Port – 4: SATA 4 Port( B type model only )

Format

y You must format when you:

– install new HDD – add another HDD – replace HDD – move HDD (change installation port) – remove HDD

y Click ( ) Add/Remove frame in Format column and choose ‘OK’ on the dialogue box to start formatting. y Following format, DVR will auto-reboot. If there are more than 2 HDDs, please format each of HDDs. DVR will auto-reboot

when all the HDDs are formatted.

y If the frame changes to ‘---‘ after reboot, it means formatting has been properly done.

CAUTION

EXECUTE REMOVE PROCEDURE EVEN WHEN YOU REMOVE PREVIOUSLY INSTALLED HDD. THE REMOVE PROCEDURE IS

THE SAME AS THE FORMAT PROCEDURE DESCRIBED ABOVE.

S.M.A.R.T y Click the frame on S.M.A.R.T column and temperature and HDD damage will show.

S.M.A.R.T Setup

y Please click ( ) S.M.A.R.T Setup and the following screen will appear.

y Check the square box 5 next to Use On. Through S.M.A.R.T function, make alarm message, indicating HDD damage, will

show.

y Check 5 Beep, it will give the alarm sound, indicating HDD damage, as the SMART setup. y Check 5 Blink Message, the alarm message will blink on the OSD, as the SMART setup. y If you uncheck Used on, Beep, Blink Message will be unchecked automatically. Only when you check5 Used on, you can

set Beep, Blink Message function.

y Click ( ) Inspection Time frame to set inspection time. y Click Check by frame to select inspection interval. y Last Check Time: show the time of the last inspection. y Click ( ) ▲, ▼ direction buttons on the right-hand side of Temperature frame to adjust to maximum temperature for the

HDD used in DVR. In general, it is 55℃.

y Click ( ) ▲, ▼ direction buttons on the right-hand side of HDD Damage frame to set the permissible level of HDD damage

(%). HDD is a very crucial element for DVR recording, so set the permissible level within 1% to 2% to assure maximum safety.

While pressing (+) or (-) button on the rightmost side of Temperature or HDD Damage item, a target value increases or decreases by 10 units.

y Choose ‘OK’ to confirm the setting.

4.2.3 Account

y Please click ( ) SYSTEM>Account and the following screen will appear.

New Group

y Please click ( ) New Group and the following screen will appear.

y Click ( ) keyboard icon on the right-hand side of Group Name frame. Then, the virtual keyboard will show. Please click ( )

desired characters (up to 8 characteristics) on the virtual keyboard.

y Do provisioning for Group Name by selectively checking 5 some of the following items (Setup, Search, Network, Archiving

and Shut Down).

y Choose ‘OK’ to confirm the setting.

y Please click ( ) Login Settings and the following screen will appear. y Selectively enable password protection for important operations (Setup, Search, Network, Archiving and Shut Down).

Please check 5 the operations you wish to enable password protection.

CAUTION

YOU WILL NOT BE ASKED TO ENTER YOUR PASSWORD FOR OPERATION(S) WHERE PASSWORD PROTECTION IS NOT ENABLED.

y Choose ‘OK’ to confirm the setting.

New User

y Please click ( ) New User and the following screen will appear. y Click ( ) the keyboard icon on the right-hand side of User Name frame and the virtual keyboard will appear. Click desired

characteristics (up to 8 characteristics) on the virtual keyboard.

y Input Password and Confirm.

y Choose ‘OK’ to confirm the setting. Then, lists of Group and User will show as follows.

y Click ( ) 6 to delete the set Group or User. y You may create up to 8 Groups and 8 Users. y Choose ‘OK’ to confirm the setting.

Password Resetting

y Click ID on User column. The following screen will appear.

y This is a screen for password resetting y Input password by clicking the keyboard icon on the right-hand side of the frame.

y Use

key if you wish to erase password on keyboard.

4.2.4 System Log

y Please click ( ) SYSTEM>System Log and the following screen will appear.

y System Log System Log displays diverse events.

– Setup (Menu) Enter/Exit – Playback Mode Enter/Exit – Network Access Enter/Exit – Archive Success/Fail – System Start/shut down – S.M.A.R.T. Check – NTP Sync/ Server Success/Fail – Send E-mail Success/Fail – HDD Format Success/Fail – Data clear Success/Fail

–

USB Upgrade Success/Fail

– DVR Setup Change by Remote – Before/After Time Adjust

y System Log removal procedure is as follows:

– Execute Clear All Data in SYSTEM>Information>Record and choose ‘OK’ on the popup dialogue box. Please note that

all normal recorded video data are deleted from database.

– Press Factory Reset Switch on the back panel. Please note that the entire menu setup is also defaulted.

4.2.5 Exit

y Please click ( ) SYSTEM>Exit and choose ‘OK’ on the popup dialogue box to exit from the setting.

CAUTION

ANY CHANGES MADE IN SETUP ARE APPLIED AFTER EXIT.

4.2.6 Shutdown

y Shutdown is a function to help you safely turn off DVR. Please use the proper shut down procedure to avoid damaging to

our DVR system. Do not remove the power during shut down.

CAUTION

DO NOT TURN DVR OFF WITHOUT USING THE PROPER SHUT DOWN PROCEDURE. OTHERWISE, IT MAY CAUSE DAMAGE TO YOUR DVR. ALWAYS REMOVE THE POWER AFTER SHUT DOWN.

y Click ( ) SYSTEM>Shutdown and then choose ‘OK’ on the dialogue box to confirm. y When you select Shutdown menu, the OSD menu on the screen disappears. y Reboot the DVR after Shutdown. Turn off the DVR and wait for 5 seconds before restart.

4.3 DISPLAY

y Please click ( ) DISPLAY and the following screen will appear.

4.3.1 OSD

y Please click ( ) DISPLAY>OSD and the following screen will appear.

y The OSD menu will allow you to configure full features (i.e., on/off every letter and icon) displayed on the screen. y Letters and icons are divided under System and Camera categories. If you click ( ) ‘All’, all items are on/off at once.

OSD Margin

y The OSD Margin menu will allow you to adjust the position of OSD (letters) on the monitor. Use it when some of letters are

dropped out and invisible on the monitor.

y Adjust Horizontal to change margin between both ends of the monitor on horizontal side and OSD. Margin range is between

0 and 50, with a larger number representing greater margin.

y Adjust Vertical to change margin between both ends of the monitor on vert 130 y Vertical side and OSD Margin range is between 0 and 50, with a larger number representing greater margin. y While pressing (+) or (-) button, a target value increases or decreases by 10 units.

De-Interlace

y This function changes playback display into Progressive Scan or Interlace Scan. Check (5) De-Interlace, then frame will

display as the Progressive Scan and shows the better picture quality.

Transparency

y The Transparency menu will allow you to alpha-blending of OSD menu on the monitor. Transparency is the quality that an

object or substance has when you can see through it.

y Transparency range is between 0 and 100, with a larger number representing can see through it. (default 0) y While pressing (+) or (-) button, a target value increases or decreases by 10 units.

4.3.2 Main Monitor

y Please click ( ) DISPLAY>Main Monitor and the following screen will appear.

y The Main Monitor menu will allow you to adjust channel sequencing interval of Main monitor.

Full Seq

y Adjust interval for ‘Full screen sequencing’. y Check 5 check box next to the camera you want to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.

y Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to 3>5>10>15>30>60

seconds by each press.

Quad Seq

y Use only with 8 / 16 channel DVRs. y Adjust interval for ‘X4 Split Screen sequencing’. y Check 5 check box next to the camera you want to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.

y Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to 3>5>10>15>30>60

seconds by each press.

y ‘4 Split Screen sequencing’ is disabled in the following modes.

– 8 channel DVR: 3x3 Mode – 16 channel DVR: 4x4 Mode

X9 Seq

y Use only with 16 channel DVR. y Adjust interval for ‘X9 Split Screen sequencing’.

y Check 5 check box next to the camera you want to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.

y Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to 3>5>10>15>30>60

seconds by each press.

y ‘9 Split Screen sequencing’ is disabled in 4X4 Mode.

4.3.3 Spot Monitor

y Please click ( ) DISPLAY>Spot Monitor and the following screen will appear.

y This menu will allow adjust interval of channel sequencing of Spot monitor. y Click ( ) Spot Select to choose Spot monitor to be set up. y Check (check box next to the camera you want to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.

y Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to 3>5>10>15>30>60

seconds by each press.

4.3.4 Spot Monitor Control on Display Mode

y A Type : Every click of the “SPOT” menu item on mouse right click menu will indicate “SP”, “SP1” on the right bottom of

main monitor.

- SP mode: Sequential display is activated as configured on spot monitor Setup menu.

- SP1 mode: Displayed channel on Spot monitor 1 can be changed by pressing channel button.

Sequence stops at “SP1” mode

y B Type : Every click of the “SPOT” menu item on mouse right click menu will indicate “SP”, “SP1”, “SP2” and “SP3” on the

right bottom of main monitor. After “SP3”, the it shows nothing. And system gets out of spot monitor control mode.

- SP mode : Sequence is activated as configured on spot monitor Setup menu.

- SP1 mode : Displayed channel on Spot monitor 1 can be changed by pressing channel button. Sequence stops at “SP1” mode.

- SP2 mode : Displayed channel on Spot monitor 2 can be changed by pressing channel button.

Sequence stops at “SP2” mode.

- SP3 mode : Displayed channel on Spot monitor 3 can be changed by pressing channel button.

Sequence stops at “SP3” mode.

+ 71 hidden pages

Cantek D1648-1TB User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual