Cantek CT-W-HDMT3520 Specsheet

Page 1
HHDD CCooaaxxiiaall TTeesstteerr
Appl ic ation
Feat ures
W-HDMT3520
3.5”HVGA TFT-LCD screen display/480 (RGB)*320 resolution /HD coaxial test (CVI/TVI/AHD) /PTZ
The new HD coaxial tester is developed for the On-Site installation and maintenance of coaxial camerait also combine other functions analog camera test, video level meter, analog signal output, IP address scan, Ping, port finder, UTP test, digital multimeter ,optical power meter and TDR cable tester etc. Its portability, user-friendly design and many other functions make the IP tester an essential tool for all installers or technicians.
CCTV system installation and maintenanceNetwork cabling project installation and maintenanceDome camera and all in one camera testingVideo transmission channel testingPTZ control
1)3.5inch screen display, 480RGBx320 resolution
2) Low power consumption, working time lasts 11 hours
3) LCD screen brightness/contrast/color saturation adjustable NTSC/PAL auto adjust
4) CVI /TVI /AHD coaxial camera image display, coaxial PTZ control and call up the camera
OSD menu
5) Enhanced Color bar generator, PAL/NTSC multi-system color bar video generator (Eight-system switchable, transmit/receive eight-system colorful images).
6) LED Flashlight.
7) HD coaxial control, PTZ control, color bar generator shortcut key.
8) F1, F2 user-defined key
9) Visual fault locator, to test fiber’s bending and breakage * (Optional)
10) Digital Multi-meter, DC and AC voltage measurement, Resistance measurement Continuity test, Diode measurements, Capacitance measurement * (Optional)
11) Cable tracer, by sending the audio signal, enables the blue cable tracer tester to find the connected cable from messy cables. * (Optional)
12) Ping test, PING is the most conventional network debugging tools; it is used for testing if the connected IP camera or other network equipment's Ethernet port is working normally and the IP address is correct.
13) IP address scan The IP address scan can quickly search for connected IP cameras or
Page 2
another network device IP address
Func tion
14) POE Voltage tests the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an Ethernet cable.
15) Port Finderit will enable the installer to easily and quickly find the connected port for an Ethernet cable.
16) Link monitor check if the new setting IP address is occupied.
17) TDR cable test, TDR break-point and short-circuit measurement. * (Optional)
18) PTZ control and PTZ protocol analysis
19) Cable test, Test LAN cable or telephone cable, UTP cable etc, cable type and the sequence of wires will be displayed
20) Support more than 30 protocols, such as Pelco-D, Pelco-P, SAMSUNG.
21) Support RS232/RS485,rate 600 115200bps adjustable
22) Built in Lithium Ion Polymer Battery3.7V DC 3000mAh
23) Image display and data control integration
24) Handheld HD coaxial tester, easy to carry and operation.
25) Optical power meter, test fiber loss and value * (Optional)
26) HD SDI tester, support 1080P (Optional)
1. Video signal test
The new HD coaxial tester ,built-in high definition 3.5”LCD-TFT 480RGBx320 resolution, view the image, easy and directly displays the camera image , support PAL/NTSCLCD screen brightness/Contrast/Color Saturation adjustable. Suitable for field construction and maintenance work
2. HD coaxial signal test
TVI, CVI, AHD coaxial signal test, support 1080P, the tester will display camera image, coaxial PTZ control and call up the camera OSD menu.
3. Video signal level test (For analog)
Test video signal strength attenuation, longer video signal cable will cause the image to be dim, and reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce the sharpness of the image. It also can real-display the video level value, if out of range, notices will be display in the screen.
4. PTZ controller
Display the input video images. Pan/tilt the P/T unit the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.
5. Enhanced color bar generator
Page 3
The tester sends out color bars via its BNC output to the monitor. This is used to test for a
problem in the cable going from the camera back to the monitoring area
6. DC12V 1A output power
Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing when the power supply is not available.
7. Audio testing
Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
8. Cable tester
Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the HD coaxial tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable tester kit.
9. PTZ controller
Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission. Screen displays 16 hexadecimal codes such as PELCO-PA0 00Add xx xxxxxx AF xx PELCO-DFF 01Addxx xxxxxxxx
10. PTZ address scanning
Search up the ID of PTZ camera. Help the engineer search the speed dome address quickly.
11. Cable scan (Optional) *
Send the specific signal, easy to find the connected cable from the mess cable
12. Port finder
The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable the installer to easily and quickly find the connected port for an Ethernet cable.
13. IP address san
The IP address scan can quickly search for connected IP cameras or another network device IP
address.
14. Link monitor
To add an IP camera or other network device to the current network group, the new IP address must not be occupied; otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied.
15. PING test
PING is the most conventional network debugging tool; it is used for testing if the connected IP
Page 4
camera or other network equipment is working normally and the IP address is correct.
16. PoE test
Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an Ethernet cable.
17. Visual fault locator * (Optional)
Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single mode fiber’s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light output. It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.
18. Digital multimeter (Optional)*
HD coaxial tester built in highly stable and reliable 33/4 digit (6600) digital multimeter. It is used for the DC and AC voltage measurement,AC and DC current measurement, Resistance measurement, Continuity test, Diode measurements, Capacitance measurement, Auto/Manual measuring range switching, relative value measurement and locking . It is easy operation and professionally accurate.
19. LED lamp
Press the LED On/Off button to use the LED flashlight.
20. HD coaxial, PTZ control and color bar generator shortcut key
HD coaxial, PTZ control and color bar generator shortcut key, easy to operate
21. F1, F2 User-defined shortcut keys
The user-defined shortcut key is designed for improving the efficiency for the engineer, anytime press, easy to operate.
22. TDR cable test * (Optional)
TDR cable testing, accurately measure BNC cable, network cable, controls cable's open circuit
and short-circuits location. It greatly improves working efficiency
23. Optical power meter, test fiber loss and value * (Optional)
The IP camera tester adopts the most advanced handheld instrument specific integrated chip ,
achieve ultra-low power operation, with the 7 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm ,1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss.
NoteWith sign“ * ” means functions are optional, Optional function need pay
additional cost if asked to add any one of them in the tester
Page 5
Model
HD coaxial tester W-HDMT3520 *models are Optional
Video Test
Signal mode
NTSC/PAL (Auto adapt)
Display
3.5 inch digital TFT-LCD ,480RGBx 320 resolution
LCD adjustment
Brightness, Contrast, Saturation adjustable
Video IN/OUT
1 channel BNC Input & 1 channel Output
Video Output Mode
1.0 Vp-p
Video Level test
Level test
Video signals measured in IRE or mV ( for analog )
Video level meter (Optional)
Video Level meter
PEAK video signal level, SYNC signal level, COLOR BURST chroma level measurement
PTZ controller
Communication
Support RS232 and RS485
PTZ Protocol
Compatible with more than 30 protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc.
Baud Rate
600,1200,2400,4800,9600,19200,57600,115200bps
Video signal generation
Color bar generator
Output one channel PAL/NTSC color bar video signal for testing monitor or video cable.(red, green ,blue, white and black color )
UTP cable tester
UTP cable test
Test UTP cable connection status and display in the screen. Read the number of the test box.
DC12V 1A power output
DC12V power output
Output DC12V1A power for camera
Audio input test
Audio input test
test the pickup and other audio equipments on the front-end
RS485 data analysis
Data Monitor
Captures and analyzes the command data from controlling device
CVI testOptional*
CVI video signal test
1 channel CVI inBNC interfacesupport 720p 25/30/50/60fps,1080p 25/30fps,camera OSD menu control over coaxial cable
TVI testOptional*
TVI video signal test
1 channel TVI inBNC interface support 720p 25/30/50/60fps,1080p 25/30fps,camera OSD menu control over coaxial cable
AHD testOptional*
AHD video signal test
1 channel AHD in (BNC interfacesupport AHD 2.0 version, 720p 25/30fps,1080p 25/30fps,camera OSD menu control over coaxial cable
Port flicker
Port flicker
Find the connected POE port quickly.
IP scan, Link monitor, PING test
IP scan
Find out the connected IP camera or the other network equipment IP address quickly.
Specific at ions
Page 6
Link monitor
Check the IP address whether is occupied
PING testing
Test IP camera or Ethernet port of the other network equipment whether work normally, and check the IP address
Cable scan (Optional) *
Cable scan
Search the cable by the audio signal
PoE tester
PoE tester
Display the power supply voltage and cable connection states
Digital Multimeter (Optional) *
AC/DC Voltage
0-660V auto/manual range, the min resolution is 0.1mV
AC/DC current
660.0uA , 6.600mA, 66.00mA , 660.0mA, 10.00A
Resistance
660.0Ω, 6.600kΩ, 66.00kΩ, 660.0kΩ, 6.600MΩ, 66.00MΩ
Capacitance
6.6nf66000uF the min resolution is 1pf
Diode
02V forward voltage, the min resolution is 1mV
Data hold
Hold and display the measured value
Relative measurement
Display the relative power value
Continuity testing
Built-in buzzer will sound, if resistance is lower than 50 Ω
Testing speed
3 times/ seconds
Data range
-6600+6600
Optical power meter (Optional) *
Calibrated Wavelength(nm)
850/1300/1310/1490/1550/1625nm Power range(dBm)
-70+10dBm
Sensitivity(nW)
0.001nW
Connector type
FC/PC
Data hold
Hold and display the measured value
Relative measurement
Display the relative power value
Visual fault locator (Optional) *
Visual fault locator
Test fiber’s bending and breakage ( SM and MM fiber)
TDR Tester (Optional) *
TDR Tester
breakpoint and short circuit measurement(BNC cable, telephone cable)
POWER
Power Adapter
DC 5V1.5A
Battery
Built-in 3.7V Lithium polymer battery ,3000mAh
Rechargeable
After charging 3-4 hour, working time lasts 11 hours
Low Consumption
Energy saving technology, the battery icon real-time display
Parameter
Operation setting
English/Chinese and other languages OSD menu
Auto off
5-60 (mins)
Keytone
On/Off
General
Working Temperature
-10 +50
Working Humidity
30%~ 90%
Dimension/Weight
194mm x 112mm x 48mm / 540g
Loading...