Page 1
HD Vandal Proof IP Dome Camera User’s Manual
Version 1.1
Page 2
Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Page 3
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Page 4
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
IPC Unit
MD9M data converter cable
Accessories bag
Quick Start Guide
CD
1
1
1
1
1
Page 5
Table of Contents
1 General Introduction ..................................................................................................................7
1.1 Overview........................................................................................................................7
1.2 Features.........................................................................................................................7
1.3 Specifications................................................................................................................8
1.3.1 Performance...........................................................................................................8
1.3.2 Factory Default Setup...........................................................................................9
2 Structure ....................................................................................................................................13
2.1 Multiple-function Combination Cable ......................................................................13
2.2 Framework and Dimension.......................................................................................14
2.3 Bidirectional talk .........................................................................................................15
2.3.1 Device-end to PC-end ........................................................................................15
2.3.2 PC-end to the device-end ..................................................................................15
2.4 Alarm Setup.................................................................................................................16
3 Installation .................................................................................................................................17
3.1 Device Installation ......................................................................................................17
3.2 SD Card Installation ...................................................................................................19
3.3 Lens Adjustment.........................................................................................................20
4 Quick Configuration Tool.........................................................................................................21
4.1 Overview......................................................................................................................21
4.2 Operation .....................................................................................................................21
5 Web Operation..........................................................................................................................24
5.1 Network Connection...................................................................................................24
5.2 Login and Main Interface...........................................................................................24
Page 6
6 FAQ ............................................................................................................................................27
Appendix Toxic or Hazardous Materials or Elements ...............................................................28
Page 7
1 General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts audio
and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series IPC uses standard H.264 video compression technology and G.711a audio compression
technology, which maximally guarantee the audio and video quality.
This series IPC enclosure has the strong resistance capacity, which can guarantee the proper work
performance under heavy strike. It supports real-time monitor and listening at the same time. It
supports analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
IPC is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
Storage
Function
Alarm
Function
Network
Monitor
Network
Management
Peripheral
Equipment
z Different user rights for each group, one user belongs to one group.
z The user right shall not exceed the group right.
z Support central server backup function in accordance with your
configuration and setup in alarm or schedule setting
z Support record via Web and the recorded file are storage in the client-
end PC.
z Support built-in SD card.
z Support local SD card hot swap, support short-time storage when
encounter disconnection.
z Real-time respond to external local alarm input, and video detect( within
200MS) as user pre-defined activation setup and exert corresponding
message in screen and audio prompt(allow user to pre-record audio file)
z Real-time video detect: motion detect, camera masking, video loss.
z IPC supports one-channel audio/video data transmit to network terminal
and then decode. Delay is within 350ms (network bandwidth support
needed)
z Max supports 10 connections.
z Adopt the following audio and video transmission protocol: HTTP, TCP,
UDP, MULTICAST and RTP/RTCP and etc.
z Support web access, widely used in WAN.
z Realize IPC configuration and management via Ethernet.
z Support device management via web or client-end.
z Support peripheral equipment management, each peripheral equipment
control protocol and interface can be set freely.
z Support serial port (RS232/RS485) transparent data transmission.
Power
Assistant
Function
z External power adapter DC12V/AC 24V and PoE.
z Log function
z Support PAL/NTSC
z Support system resource information and running status real-time
display.
7
Page 8
z Day/Night mode auto switch (ICR switch).
z Built-in IR light. Support IR night vision (For HDBW3300P/N Series
only).
z Backlight compensation: screen auto split to realize backlight
compensation to adjust the bright.
z Support electronic shutter and gain setup.
z Support video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for IPC performance specification.
Model
Parameter
System
Main
Processor
OS Embedded LINUX
System
Resources
User Interface Remote operation interface such as WEB, DSS, PSS
System Status SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor 1/2.8-inch CMOS
Pixel
Day/Night
Mode
Auto Iris DC drive
Gain Control Fixed/Auto
White Balance Manual/Auto
Exposure
Mode
Video
Compression
Standard
Video Frame
Rate
Video Bit Rate
Video Flip
Video Quality
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Information
Lens 4.5~10mm@F1.6
Lens Interface C/CS, lens is the default accessories
Audio Input
Au
Audio Output
TI Davinci high performance DSP
Support real-time network, local record, and remote operation at the same time.
2048（H）*1536（V）
Support day/night mode switch and IR-CUT at the same time.
Manual/Auto（It ranges from 1/50 to 1/10000）
H.264/JPEG
PAL:
Main stream（2048*1536@15fps），extra stream,（D1@12fps）
Main stream（1920*1080@25fps），extra stream（D1@25fps）
NTSC:
Main stream（2048*1536@15fps），extra stream（D1@12fps）
Main stream（1920*1080@30fps），extra stream（D1@15fps）
Main stream: 56kbps~8192kbps. Extra stream: 14kbps~4096kbps.
Support customized setup.
Does not support mirror.
Support flip function.
1~6 level（The 6th level has the highest quality）
Channel title, time title, video loss, motion detect, privacy mask.
1-channel，RCA audio input.
1-channel, RCA, audio output.
HDB/HDBW3300P/N
8
Page 9
di
o
Alarm Input
Backup
Interface
Bidirectional
Talk Input
Audio Bit Rate 8kbps 16BIT
Audio
Compression
Standard
Video
Motion Detect
Video Loss
Record and
Record
Priority
Record Search
Mode
Local Storage Support Micro SD card hot swap
Storage
Management
Network
Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Remote
Operation
AUX
Video Output
Reset 9-pin port connection
IR light 35 LED, IR distance 10 to 20 meters (For HDBW series product only)
RS485 port PTZ control interface. Support various protocols.
General Parameter
Power Support AC24V/DC12V power. PoE
Power
Consumption
Working
Temperature
Working
Humidify
Dimensions ¢160x118.5
Weight 1.25g
Installation
Reuse the first audio input channel
G.711a/G.711u/PCM
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th level
has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log, email
SMTP function and etc.
Activation event, alarm device, audio/video storage, image snapshot, log, email
SMTP function and etc.
2-channel input，1-channel output（on-off ）
Manual>Alarm >Motion detect>Schedule
Support local data search via time/date, event type(alarm, motion detect,
external alarm) and file type (record/image)
Support display local storage status
Standard
HTTP,TCP/IP,ICMP.RTSP,RTP,UDP,RTCP,SMTP,FTP,DHCP,DNS,DDNS,PPP
OE.
Monitor, PTZ control, playback, system setup, file download, log information,
maintenance , upgrade and etc
1-channel analog video output，BNC port, 9-pin port connection
7W MAX
-10℃~+55℃
10%~90%
Support various installation modes（Enclosure and bracket is optional）
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Default setup Function Configuration
HDB/HDBW3300P
Series
Type
General Setup
Item Name
Date format Y-M-D
DST Disable by default
Date separator ‘ _ ’
HDB/HDBW3300N
Series
Time format 24H
Language Simplified Chinese
When HDD is full Overwrite
Record duration 8M
9
Page 10
Device No. 8
Video type PAL
Encode
Setup
Main
Stream
Extra
Stream
Image Color Brightness:50
Watermark Enable
Privacy Mask
Time title Enable.
Channel Channel01
Encode mode H.264
Audio/Video enable Enable audio and video
General bit stream General bit stream
Resolution 1080P
Frame rate 25 30
Bit stream control CBR
Quality Good
Bit stream value 8192
I frame interval control 50 60
Extension Stream General bit stream
Audio/Video enable Disable
Resolution D1
Frame rate 25 30
Bit stream control CBR
Quality Good
Bit stream value 2048
I frame interval control 50 60
Contrast:50
Sautratioon:50
Hue:50
Gain:80.Disable
Watermark: all
Watermark type: character
Watermark: DigitalCCTV
Never
Channel title Enable.
Record Setup
COM Setup
Network Setup
Channel Ch01
Pre-record 1 second.
Time Setup
Option COM01
Function General
Data bit 8
Stop bit 1
Baud rate 115200
Parity None
Ethernet Port 01
DHCP Disable
IP address 192.168.1.108
Subnet mask 255.255.0.0
Gateway 192.168.0.1
Device name Device factory default name
TCP port 37777
HTTP port 80
UDP port 37778
Network user connection
amount
Start Time 0:00:00
End Time 23:59:59
Record Period 1:Enable motion detection/alarm
Snapshot Period 1: Enable motion detection/alarm
4
10
Page 11
DNS
Alternative DNS
Advanced
Email setup Enable
Multiple DDNs Disable
NAS setup Disable
NTP setup Disable
Alarm server Disable
Network
transmission
QoS
Remote host Multiple broadcast group
Enable Disable
IP address 239.255.42.42
Port 36666
8.8.8.8
8.8.8.8
Disable
Alarm Setup
Video Detection
PTZ Setup
Event type Local alarm
Alarm input Input 01.
Type Normal open
Setup Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Anti-dither 0 second
Alarm output Disable
Alarm latch 10 seconds
Record channel 1, enable
Record latch 10 seconds
Send email Disable
PTZ activation Disable
Event type: never
Address: 0
Snapshoot Disable
Event type Motion detection
Channel Ch01, Disable
Sensitivity 3
Time period setup Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Anti-dither 5 seconds
Alarm output Disable
Alarm latch 10 seconds
Record channel Disable
Record latch 10 seconds
Send email Disable
PTZ activation Event type: Never
Address: 0
Disable
Snapshot Disable
Channel Ch01
Protocol DH-SD1
Address 1
Baud rate 115200
Data bit 8
Stop bit 1
Parity None
11
Page 12
Default and Backup
Advanced
Additional
All Disable
General Disable
Encode Disable
Record Disable
COM Disable
Network Disable
Alarm Disable
Video detection Disable
Display output Disable
Channel No. Disable
Record control Auto. Ch1 (This series device does not
Abnormity
Alarm I/O Alarm output
Record Control Auto: Ch1 (This series device does not
User account
Snapshot
Auto
maintain
Even Type No HDD, Disable
Alarm
Output
Alarm Latch 10 seconds
Send email Disable
Channel Ch01
Snapshot
mode
Frame rate 1f/s
Resolution 1080P
Quality 80%
Auto reboot 2.00 each day
Auto delete
old files
Enable Disable
SN 1
IP 0.0.0.0
Port 7000
Device ID None
Channel 1
Exposure
mode
BLC Disable (This series device does not
Day/Night
mode
Signal Type INT
Mirror N/A
Flip Disable
Auto
Aperture
support this function.)
Disable
support this function.)
admin--- password: admin (reusable)
888888--- password: 888888(reusable)
666666--- password: 666666(reusable)
Scheduled
Never
Auto
support this function.)
Auto
Enable
Scene mode Auto
Talk Encode Talk Encode G.711A
12
Page 13
2 Structure
2.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See Figure
2-1
.
Figure 2-1
Please refer to the following sheet for detailed information.
Port Name Function Connection Note
VIDEO OUT
AUDIO IN
AUDIO OUT
12V DC/AC24V
I/O I/O cable port / Connect to I/O port cable.
LAN Network port
Please refer to the follow sheet for detailed information of MD9M data converter cable.
Port Name Cable
Video output
port
Audio input
port
Audio output
port
Power input
port
Color
Name Note
BNC
RCA
RCA
/ Power port. Input DC 12V/AC 24V
Ethernet
port
Output analog video signal. It can connect to the
TV monitor to view the video.
Input audio signal. It can receive the analog audio
signal from the pickup.
Output audio signal to the devices such as the
sound box.
z Connect to standard Ethernet cable.
z Support PoE.
I/O Port
Pin
Yellow RS485_A RS485_A port. It is to control the PTZ.
Black RS485_B RS485_B port. It is to control the PTZ.
Red ALARM_COM Alarm output public port.
Brown ALARM_IN1
Grey ALARM_IN2
Alarm input port 1. It is to receive the on-off signal
from the external alarm source.
Alarm input port 2. It is to receive the on-off signal
from the external alarm source.
13
Page 14
Port Name Cable
Color
White ALARM_NO
Blue RESET
Orange GND Ground port
Name Note
Alarm output port. It is to output the alarm signal
to the alarm device.
NO: normal open alarm output port.
It works with the ALARM_COM port.
It is to restore factory default setup.
When the device is working properly, please
connect the blue cable (restore default setup port)
to the orange cable (GND signal) for 5 seconds,
the device can resume factory default setup.
2.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.
Figure 2-2
14
Page 15
Figure 2-3
2.3 Bidirectional talk
2.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or the pickup to the first audio input port in the device rear panel. Then
connect the earphone or the sound box to the audio output port in the PC.
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the following interface to enable bidirectional talk.
Figure 2-4
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
2.3.2 PC-end to the device-end
Device Connection
15
Page 16
Connect the speaker or the pickup to the audio output port in the PC and then connect the earphone
or the sound box to the first audio input port in the device rear panel.
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the above interface (Figure 2-4) to enable bidirectional talk.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone
or sound box at the device-end.
2.4 Alarm Setup
The alarm interface is shown as in Figure 2-5. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (grey or brown pin of I/O port cable).
2) Connect the alarm output device to the alarm output port (White-pin) and alarm output public port
(Red-pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2-5. Please set the alarm input 01 port for the brown-pin (the 1
channel) of I/O port cable. The alarm input 02 is for the grey-pin (the 2
Then you can select the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output port of the alarm output 01 device (The white-pin of the
I/O port cable).
nd
channel) of I/O port cable.
st
Figure 2-5
16
Page 17
3 Installation
This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the in-
ceiling installation to realize the hang function. Please refer to the steps listed below.
The device is shown as in Figure 3-1.
Figure 3-1
3.1 Device Installation
Step 1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover
and then open the cover. See Figure 3-2.
Step 2
With IR light Without IR light
Figure 3-2
17
Page 18
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome and
then remove the device pedestal. See Figure 3-3.
With IR light Without IR light
Figure 3-3
Step 3
Draw out the cable exit and four screw holes in the installation position according to the device
pedestal. Dig the four plastic expansion bolt holes and cable exit. Insert the four plastic expansion
bolts into the screw holes
Step 4
Adjust the camera pedestal to the proper position and then draw the cable through the cable exit you
just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four plastic
expansion bolt holes in the installation position. Put the four self-tapping screws in the device pedestal
and then use the screwdriver to secure the screws in the four plastic expansion bolts firmly.
Step 5
Adjust the device position and line up the three inner hexagon screws of the device to the three holes
of the installation position. Put the three inner hexagon screws into the screw holes at the bottom of
the pedestal. Use the inner hexagon screwdriver to fix firmly. See Figure 3-4.
Step 6
With IR light Without IR light
Figure 3-4
18
Page 19
Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the steps
listed below to adjust.
Please note, for the dome of the IR light, you can skip step a) and step e).
z a): Slightly push the two sides to squeeze the plastic hook so that you can take off the dome
enclosure.
z b):Slightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust the
module tilt rotation angle (15°～90°).
z c):Slightly loose the screw of the pressing slice, you can adjust the video rotation angle of the
module (0°～355°)
z d):Adjust the turning ring of the pedestal, you can adjust the module pan rotation angle (
0°～
355°).
z e): Put the enclose back after you completed the setup.
Please note, the screws in the following figure are the optical adjustment component. Please
make sure it is outward and do not allow it to touch the X-Y-Z axis module. See Figure 3-5
Figure 3-5
Step 7
Put the dome cover back and then put the three inner hexagon screws into the holes of the device.
Use the inner hexagonal wrench to fasten these three screws. See Figure 3-6
Figure 3-6
3.2 SD Card Installation
19
Page 20
Important
Before you install the SD card, please unplug he power cable to shut down the device!
First, please refer to the step1 in the chapter 3.1 to open the device.
Second, please adjust the proper position to install the SD card.
Last, please refer to the step 7 in the chapter 3.1 to complete the installation. See Figure 3-7.
With IR light Without IR light
Figure 3-7
3.3 Lens Adjustment
Step 1
Slightly loose the screw B manually and then turn the screw B slowly. Adjust the lens focus distance to
the proper position according to the monitor video. See Figure 3-8.
Step 2
Use the flat screwdriver to loose the screw A slightly and then turn the Screw A slowly. Adjust the lens
focus to get the clear video and then use the flat screwdriver to secure the screw firmly.
Step 3
When you are adjusting the screw A, the video may becomes blur. Please slightly adjust the screw B
manually to get the vivid video. Finally fix the screw.
With IR light Without IR light
Figure 3-8
20
Page 21
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Figure 4-2
21
Page 22
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure
4-3.
Figure 4-3
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.
22
Page 23
Figure 4-5
23
Page 24
5 Web Operation
This series IPC product support the Web access and management via PC.
Web includes several modules includes monitor channel list, record search, alarm setup, system
configuration, PTZ control, monitor window and etc.
IP camera factory default setup:
z IP address: 192.168.1.108.
z User name: admin
z Password: admin
5.1 Network Connection
Please follow the steps listed below for network connection.
z Make sure the IPC has connected to the network properly.
z IPC IP address and PC IP address shall be in the same network segment. IPC default IP address
is 192.168.1.108. If there is router, please set the corresponding gateway and subnet mask.
z Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.
5.2 Login and Main Interface
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 5-1.
Input your IP
address here
Figure 5-1
System pops up warning information to ask you whether install control webrec.cab or not. Please click
OK button, system can automatically install the control. When system is upgrading, it can overwrite the
previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable
the control download. Or you can lower the IE security level. See Figure 5-2.
24
Page 25
Figure 5-2
After installation, the interface is shown as below. See Figure 5-3.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Figure 5-3
After you logged in, you can see the main window. See Figure 5-4.
25
Page 26
Figure 5-4
Please refer to the HD Vandal Proof IP Dome Camera Web Operation Manual included in the
resource CD for detailed operation instruction.
26
Page 27
6 FAQ
Bug
I can not boot up
the device.
SD card write
times
I can not use the
disk as the storage
media.
I can not upgrade
the device via
network.
Recommended SD
card brand
Audio function Please use active device for the audio monitor input, otherwise there
To guarantee
setup update
Please click RESET button for at least five seconds to restore
factory default setup.
Do not set the SD card as the storage media to storage the
schedule record file. It may damage the SD card duration.
When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).
When network upgrade operation failed, you can use port 3800 to
continue upgrade.
Kingston 4GB， Kingston 1GB， Kingston 16GB， Transcend
16GB， SanDisk 1G， SanDisk 4G
Usually we recommend the 4GB (or higher) high speed card in case
the slow speed results in data loss.
is no audio in the client-end.
After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.
Power adapter The power adapter included in the accessories bag can work
ranging from 0℃ to 40 ℃. The device may result in unstable power
supply when the temperature exceeds the working temperature.
Please replace an industry-level power adapter if you are using in
the harsh environments.
27
Page 28
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Circuit Board
Component
Device
Construction
Material
Wire and Cable
Packing
Components
Accessories ○ ○ ○ ○ ○ ○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes。
Note
Pb Hg Cd Cr VI PBB PBDE
○ ○ ○ ○ ○ ○
○
○
○ ○ ○ ○ ○ ○
Toxic or Hazardous Materials or Elements
○ ○ ○ ○ ○
○ ○ ○ ○ ○
z This user’s manual is for reference only. Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z If there is any uncertainty or controversy, please refer to the final explanation of us.
z Please visit our website for more information.
28
Loading...