Cantek CT-IPC-EBW81200 Quick User Guide

Page 1
HD
Fisheye Panorama Network Camera
Quick Start Guide
Version 1.0.1
Page 2
Welcome
Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
1Electrical safety
All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. This series product supports PoE too.
Note: Do not connect these two power supplying sources to the device at the same time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. We are not liable for any problems caused by unauthorized modification or attempted repair.
2Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
3Installation
Do not apply power to the camera before completing installation. Please install the proper power cut-off device during the installation connection. Always follow the instruction guide the manufacturer recommended.
4Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.
i
Page 3
5Environment
Accessory Name
Amount
Network Camera
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
Warranty Card and Certificate
1
This series network camera should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. Please keep it away from the electromagnetic radiation object and environment. Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into the camera. Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera. Dome enclosure is the optical component, do not touch the enclosure when you are installing the device or clean the enclosure when you are doing maintenance work.
7. Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.
ii
Page 4
Table of Contents
1 Structure ................................................................................................................ 1
1.1 Device External Cable ........................................................................... 1
1.2 Dimensions .............................................................................................. 2
1.3 Bidirectional Talk .................................................................................... 3
1.3.1 Device-end to PC-end .................................................................... 3
1.3.2 PC-end to Device-end .................................................................... 3
1.4 Alarm Setup............................................................................................. 3
2 Installation ............................................................................................................. 5
2.1 General Installation ................................................................................ 5
2.2 Device Installation Steps ....................................................................... 5
2.3 Micro SD Card Installation .................................................................... 6
2.4 Manual Zoom Lens Focus Operation .................................................. 7
3 Quick Configuration Tool .................................................................................... 8
3.1 Overview .................................................................................................. 8
3.2 Operation ................................................................................................. 8
4 Web Operation .................................................................................................... 10
4.1 Network Connection ............................................................................ 10
4.2 Login and Main Interface .................................................................... 10
4.3 Panorama Function on Web ............................................................... 12
4.3.1 Installation Mode ........................................................................... 12
4.3.2 Display Mode ................................................................................. 12
Appendix Toxic or Hazardous Materials or Elements ......................................... 13
iii
Page 5
1
1 Structure
NO.
Port
Port Name
Connector
Function Description
1
AUDIO OUT
Audio output port
RCA
Output audio signal to the speakers.
2
AUDIO IN
Audio input port
RCA
Input audio signal, receive the analog audio signal from the sound pick-up.
3
LAN
Network port
Ethernet port
Connect to standard Ethernet cable.
4
I/O
I/O port
-
Connect I/O port
5
POWER
Power input port
-
Power port, input DC12V or AC 24V. Default DC5.5 round port to 2pin converter cable.
Note: Please connect the DC5.5 round port to 2-pin
converter cable when you are using AC 24V power.
Actual use in accordance with device label instruction.
1.1 Device External Cable
Figure 1- 1
The device external cable is shown in Figure 1- 1. Please refer to Sheet 1-1 for corresponding information about external cable functions.
Please refer to Sheet 1-2 for corresponding information about I/O port functions.
Sheet 1-1
Page 6
2
Port Name
Cable Number
Cable Port Name
Function Description
I/O port
1
ALARM_NO
Alarm output port. It is to output the alarm signal
to the alarm device.
NONormal open alarm output port. This port needs to be used with ALARM_COM
port
2
ALARM_COM
Alarm output public port.
3
ALARM_IN1
Alarm input port 1. It is to receive the on-off signal from the external alarm source.
4
ALARM_IN2
Alarm input port 2. It is to receive the on-off signal from the external alarm source.
5
GND
Ground port
Sheet 1-2
1.2 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See Figure 1- 2,
Figure 1- 3 and Figure 1-4.
Figure 1- 2
Figure 1- 3
Page 7
3
Figure 1-4
1.3 Bidirectional Talk
1.3.1 Device-end to PC-end Device Connection
Please connect the speaker or MIC to the audio input port of the PC, and then connect the earphones to the audio output port of the PC. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the bidirectional talk function. Click Talk button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker or MIC, and then you can get the audio at the pc-end.
1.3.2 PC-end to Device-end Device Connection
First connect the speaker or MIC to the audio input port of the PC, and then connect the earphones to the audio output port of the PC. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button became orange after you enabled the bidirectional talk function. Click Talk button again to stop the bidirectional talk function. Bidirectional talk function and on-site listening function cant be used at the same time for the device.
Listening Operation
At the PC end, speak via the speaker or MIC, and then you can get the audio at the device-end.
1.4 Alarm Setup
Page 8
4
Please refer to Figure 1-5 for more information about alarm setup.
Figure 1-5
Please follow the steps listed below for alarm input and output connection. Step 1 Connect the alarm input device to the alarm input port (No.4 pin) of the I/O cable. Step 2 Connect alarm output device to alarm output port (No.1pin) and alarm output public port
(No.2pin), The alarm output port supports NO (normal open) alarm device only.
Step 3 Open WEB and set corresponding alarm input and output in the alarm setup. Please set the
alarm input 01 port for the first channel of the I/O cable (No.4 pin). Then set corresponding NO/NC input according to the high/low level signal generated when alarm occurs to the alarm input device.
Step 4 Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is
the No.1 pin of the I/O cable.
Page 9
5
2 Installation
Important Before you complete the installation and setup, do not remove the electrostatic
attraction film on the transparent enclosure. Otherwise it may result in injury.
After remove electrostatic attraction film, do not touch dome enclosure in case
it may leave stain.
Before the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
2.1 General Installation
Please refer to Figure 2- 1 for device installation information. You can see there are installation screws in the accessories bag for you to install the device conveniently.
Figure 2- 1
2.2 Device Installation Steps
Step 1
Take the installation position diagram from the accessories bag and then paste it on the installation ceiling or the wall according to the monitor area. Please dig three bottom holes of the plastic expansion bolts according to the diagram. If you need to dig a hole to pull through the cable on top of installation surface, you need to dig a cable exit hole of no less than 28MM on the installation surface according to the installation positioning diagram, which makes the network cable go through.
Page 10
6
Step 2
Insert 3 expansion bolts from the accessories bag into the bottom holes and lock them firmly, adjust the position of device installation pedestal and pull the cable through the cable exit hole on the installation surface.
Step 3
Aim 3 screw fixed holes on the installation chassis to 3 plastic expansion bolt fixed holes on the installation surface, then tighten 3 ST3 self-tapping screws into 3 plastic expansion bolts and fasten them firmly, fix the installation chassis on the installation surface.
Step 4
When installing dome body, find the little gap on the dome body and make it corresponding to the TOP direction on the installation chassis, rotate the dome body in clockwise direction and secure it firmly. So far, installation is completed.
Note: Please refer to Micro SD card installation steps if you need to install Micro SD card, and operate step 4 after the installation.
Note: If connect the host GND to ground lead, may improve device reliability. The GND locates next to exit hole on the rear side of the chassis and the GND screw is M3.
Figure 2- 2
2.3 Micro SD Card Installation
Use the inner hex wrench from the accessories bag to unfasten the 3 inner hex screws on the dome camera enclosure, find the Micro SD card slot position according to the following figure then fasten back the 3 screws on the dome camera enclosure after the Micro SD card is inserted.
Page 11
7
Note: Please make sure the wire between power panel and device motherboard is firm, otherwise may cause abnormity. Please put the enclosure back and fasten the screws tightly to prevent dust.
Figure 2-3
2.4 Manual Zoom Lens Focus Operation
The lens of the HD panorama dome network camera is 360°, no manual zoom is required when it is operated by in-ceiling mount or ground mount. The lens of the HD panorama dome network camera is 185°, no manual zoom is required when it is operated by wall mount.
Page 12
8
3 Quick Configuration Tool
3.1 Overview Note:
Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 3- 1. In the device list interface, you can view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Figure 3- 1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 3-1. Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 3-2
If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 3-1),
Page 13
9
please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 3-3. In Figure 3-3, you can view device IP address, user name, password and port. Please modify the corresponding information to login. Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface. Otherwise, you cannot login the device. If you are using device background upgrade port 3800 to login, other setups are all invalid.
Figure 3-3
After you logged in, the configuration tool main interface is shown as below. See Figure 3-4.
Figure 3-4
For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.
Page 14
10
4 Web Operation
Input your IP address here
This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc.
4.1 Network Connection
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly. Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.168.1.1
Use order ping ***.***.***.*** (* network camera address) to check connection is OK or not.
4.2 Login and Main Interface
Open IE and input network camera address in the address bar. For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address bar. See Figure 4- 1.
Figure 4- 1
The login interface is shown as below. See Figure 4- 2. Please input your user name and password. Default factory name is admin and password is admin.
Note: For security reasons, please change your password after you first login.
Page 15
11
Figure 4- 2
After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 4-3.
Figure 4-3
Page 16
12
4.3 Panorama Function on Web
There is a panorama icon at the lower-left corner of web interface and you can click it to view installation mode and display mode on the right. Note: Please set corresponding installation mode on Web according to actual installation condition otherwise it may appear abnormity for the image display.
4.3.1 Installation Mode
There are three modes: wall mount, in-ceiling and ground.
Wall mount: It is wall mount and the camera is pointing to the front. In-ceiling: It is the in-ceiling mount and the camera is pointing to the bottom. Ground: It is the ground installation and the camera is pointing to the top.
4.3.2 Display Mode
There are six modes: 1O, 360°1-window, dual-picture panorama, 1-window, 90°4-window and 1+3 mode.
1O: Fisheye original image mode. 360°1-window: It takes the whole panorama and is one-window 360 degrees panorama. Dual-picture panorama: It is the dual-window 180 degrees panorama. 1-window: It is to display one of the four windows. It can show the video around the 360 degrees
panorama. You can select video and then implement corresponding operation.
Where you can:
1. Adjust camera direction via arrow keys. Click OK to restore default position.
2. Step length is mainly used for speed adjustment as the longer the step, the higher the speed. Zoom step length is to adjust zoom speed; movement step length is to adjust rotation speed per step; rotation step length is to adjust clockwise/counterclockwise rotation speed.
90°4-window: Panorama 360 degrees is divided into four windows. Each window has 90 degrees
and totally displayed in four channels. It can be operated in a similar way with 1-window.
1+3 mode: Display one fisheye original image + three local region images. Note: If it is under 1-window PTZ control mode, 1+3 mode, or 4-window mode, it will support following functions: left button drag, click and view and right button box zoom.
Page 17
13
Appendix Toxic or Hazardous Materials or Elements
Component Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board Component
○ ○ ○ ○ ○
Device Case
○ ○ ○ ○ ○
Wire and Cable
○ ○ ○ ○ ○
Packing Components
○ ○ ○ ○ ○
Accessories
○ ○ ○ ○ ○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized to process such kind of substances or elements, please return to the corresponding local authorities to process according to your local government statutes.
Note This user’s manual is for reference only. Slight difference may be found in user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website for more information.
Loading...