ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
INSTALLATION
&
INSTALLATION
& INSTALLATION
INSTALLATION INSTRUCTIONS
OUTDOOR
OUTDOOR
OUTDOOR
OUTDOOR
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
WALL
WALL
WALL
WALL
MOUNT
MOUNT
MOUNT
MOUNT LIGHT
LIGHT
LIGHT
LIGHT FIXTURE
FIXTURE
FIXTURE
FIXTURE
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING
MOUNTING
MOUNTING
MOUNTING THE
Installation
Installation
Installation
Installation (see
1. Shut off the power at the circuit breaker and remove old fixture,
including the cross bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface. Take care not to lose any small parts necessary for
installation.
3. Attach the mounting screw part way into the side hole of the crook
cross bar , then lock it securely with hex nut until becoming . Attach
the cross bar to the junction box using two box screws . The side of
the cross bar marked “ GND ” must face out.
4. Follow wiring instructions carefully (see
5.
5.
5.
5. Attach the back plate of the lamp body(A) onto the junction box,
aligning screws on cross bar with mounting holes and lock it
securely with the ball nuts(B). Put the candle sleeve(D) over the
lamp holder.
6.
6.
6.
6. Install the light bulb s in accordance with the fixture’s
specifications. DO
WATTAGE
WATTAGE
WATTAGE
WATTAGE RATING!
7. Raise the finial(H) to the bottom hole of glass frame(F) and lock it
securely with the hex nut(G) until tight. Removing the cover on the
glass(E) sheet sponge, raise the glass(E) into the glass frame and
lock it securely with the clip. Attached glass frame(F) to bottom of
lamp body(A), lock it securely with the ball nut(C).
With
With
8. With
With silicone
where
where
where
where back
water
water
water
water from
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE
(see
fig.1)
(see
fig.1)
(see fig.1)
fig.1)
DO
DO
DO NOT
RATING!
RATING!
RATING!
silicone
silicone
silicone caulking
back
back
back of
from
from
from seeping
caulking
caulking
caulking compound
of
cover
of
cover
of cover
cover meets
seeping
seeping
seeping into
NOT
NOT
NOT EXCEED
compound
compound
compound ,
meets
meets
meets with
into
outlet
into
outlet
into outlet
outlet box.
(see
fig.2)
(see
fig.2)
(see fig.2)
fig.2)
EXCEED
EXCEED
EXCEED THE
,
caulk
,
caulk
, caulk
caulk completely
with
the
with
with the
box.
box.
box.
wall
the
wall
the wall
wall surface
THE
THE
THE MAXIMUM
MAXIMUM
MAXIMUM
MAXIMUM
completely
completely
completely around
surface
surface
surface to
around
around
around
to
prevent
to
prevent
to prevent
prevent
Wiring
Wiring
Wiring
Wiring (see
1. Connect the electrical wires as follows. Connect the
2.Tuck the wire connections neatly into the wall junction
(see
fig.2)
(see
fig.2)
(see fig.2)
fig.2)
black wire from the fixture to the black house (hot)
Wire. Connect the white wire from the fixture to the
white (neutral) house wire. Make sure all wire nuts are
secured.
tape.If your outlet box has a ground wire (green or bare
copper) connect fixture’s ground wire to it. Otherwise
attach the bare copper fixture wire to the green ground
screw on the cross bar.
box.
You
may wrap the connections with electrical
F ig.1
Fig.2
A
B
C
D
E
F
G
H
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare Copper(Ground)
U
R
Listed
L
Loading...