Assembly Instruction
ToolsRequired:Flatheadscrewdriver,Phillips screwdriver,pliers,wirecutters,wire
strippers,electricaltape,safetyglasses.
BulbRecommended: (3) Candelabra Base 60W Maximum
EstimatedAssemblyTime:20-30 minutes
Preparation:Identifyandinspectallpartsbeforebeginning installation. Check package
contentlistanddiagramsbelowtobesure all parts are present. If any parts are missing
ordamaged,donotattempttoassemble,install,or operate the fixture. Contact customer
serviceforreplacementparts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
Package Contents
Part
A Crossbar
B
C
D
E
F
G
H
I
J
Description
Nipple
Lock Washer
Hex Nut
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Fixture Loop Assembly
Glass Frame
Quantity
1pc.
1pc.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
B
C
D
I
E
F
H
G
1of6
J
FINISH: MEDICI BRONZE
QUIOZEL
GND
2.4 mm13 Ga
1”
Dia. 5”
3
Overall Height 117.5”
(Includes 96” Chain)
2
(3)60W Candelabra
base bulbs
(not Supplied)
20.5”
14.5”
1
6”
9”
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
PART NUMBER
NO.
1
2
3
4
REPLACEMENT PART DESCRIPTION
CANDLE COVER MEDC BRNZ 2"H
CHAIN MEDC BRNZ 3.8MM X4'
MTG HDW/CNPY MEDC BRNZ 5"D
2of6
REQ.
3
1
1
Assembly Instruction
STEP 1 - Attach Fixture Loop Assembly to
Glass Frame
A. Thread the Fixture LoopAssembly (I) onto the Hex
Coupling on the top center of the Glass Frame (J). Hand
tighten until snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Secure the Corssbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
Mounting
Hole
Fixture Loop
Assembly
Hex Coupling
Glass
Frame
Figure 1
Outlet Box
Crossbar
Outlet Box
Screw (not
Supplied)
STEP 3 Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
Figure 2
Crossbar
Lock Washer
Hex Nut
Socket
Figure 3
3of6
Assembly Instruction
STEP 4 - Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (E) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (E) and hand tighten until snug.
STEP 5 Assemble Ceiling Canopy-
A. Push the Ceiling Canopy (H) upward over the Outlet
Box. Thread the Canopy Lock Ring (F) onto the Canopy
Chain Loop (E) and tighten until snug to secure the
Ceiling Canopy (H).
Outlet Box
Nipple
Crossbar
Hex Nut
Lock Washer
Canopy
Chain Loop
Figure 4
Outlet Box
Canopy Chian Loop
STEP 6 Attach Fixture Chain to Canopy
-
Chain Loop and Fixture Loop
A. Adjust the Fixture Chain (G) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (G) onto the
Canopy Chain Loop (E) and then attach the other end of
the Fixture Chain (G) onto the Fixture Loop (I) on the
top of the fixture.
Ceiling Canopy
Canopy
Lock Ring
Fixture Loop
Figure 5
Canopy Chain Loop
Fixture Chain
Supply Wire and
Ground Wire
Figure 6
4of6
Assembly Instruction
STEP 7 Pass Supply Wires through Fixture
-
Chain
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (G) alternating links. Push the wires up
through the Canopy Chain Loop (E) into the outlet box.
STEP 8 - Make Wire Connections
A. Un-thread the Canopy Lock Ring (F) and slide Canopy Lock
Ring (F) and Ceiling Canopy (H) down the Fixture Chain (G).
B. Push all slack fixture wire through Canopy Chain Loop (E)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare
wire ends according to instructions supplied with connectors.
D. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
E. Connect Black (or Red) Supply Wire from the Outlet Box to
Black Wire from fixture.
F. Connect Ground Wire from the Outlet Box to Ground Wire
from fixture.
G. Twist connectors until wires are tightly joined together.
H. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
G. Re-attach the Ceiling Canopy (H) as shown in Step 5.
Supply Wire
and Ground
Wire from
Outlet Box
Canopy Chain
Loop
Fixture Chain
Supply Wire
and Ground Wire
Figure 7
Supply Wire and
Ground Wire
Canopy Chain Loop
Fixture Chain
Ceiling Canopy
Canopy Lock Ring
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Figure 9
Black wire from fixture
5of6
Figure 8
Assembly Instruction
STEP 9 - Install Bulb
A. standard bulb with a candelabra screw
This fixture uses
base 100
. Maximum watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place.
Your fixture hanging lamp is now assembled and ready to
use. Enjoy!
Socket
Glass
Frame
Bulb
Figure 10
6of6
Loading...