Canon VB-C500D User Manual

Network Camera
VB-C500D
Start Guide
Please read carefully this Start Guide and the Operation Guide Especially be sure to read "Safety Precautions" before using the network camera. Keep this guide in a readily accessible location for future reference.
Thank you for purchasing Canon Network Camera VB-C500D (hereafter referred to as VB-C500D).
This Start Guide describes how to set up and install the VB-C500D. The detailed procedures for using the VB-C500D are explained in the Operation Guide provided on the Setup CD-ROM. Read these guides carefully before using the VB-C500D to ensure that you make the best possible use of this product. Also, be sure to read "Safety Precautions" in this guide.
For the latest information on this product (firmware, bundled software, operation manuals, operating environment, etc.), visit our website.
Disclaimer
Canon Inc. shall not be responsible for any financial losses that may be incurred as a result of the loss of recorded information or images, regardless of the internal or external cause of the loss.
Copyright
Videos, images or sounds recorded with your VB-C500D may not be utilized or published, without consent of copyright holders, if any, except in such a way as permitted for personal use under the relevant copyright law.
Notes
1. All rights reserved.
2. The contents of this guide are subject to change without any prior notice.
3. This document has been prepared with utmost attention to accuracy. If you have any comment, however, please contact the Customer Service Center indicated on the back cover.
4. Canon shall assume no liability for any outcome of using this product, regardless of Items 2 and 3 above.
Notes on privacy and publicity rights regarding the utilization of video/audio
When using the VB-C500D (for video or audio recording), it is the responsibility of the users to take all care to protect privacy and avoid any violation of publicity rights. Canon shall have no liability whatsoever in this regard.
Reference
Please be sure to gain approval of the building management office before installing a
camera, if copyrighted architectural structures or copyrighted premises are appear in the frame.
Legal Notice
In some countries or regions, monitoring via a camera is banned by the law or regulation, and the law or regulation depends on the country or region. Before using the VB-C500D, confirm the law or regulation of the country or region where the camera is used.
ii
Introduction
Trademark Notice
Canon and the Canon logo are registered trademarks of Canon Inc.
Microsoft Windows and Microsoft Internet Explorer are trademarks or registered
trademarks of Microsoft Corporation in the United States and other countries.
Windows is legally recognized as the Microsoft Windows Operating System.
Other brands or product names in this guide are trademarks or registered trademarks
of their respective companies.
Warning
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Notes on Use of Bundled Software VK-Lite (Disclaimer)
Malfunction, failure of VK-Lite or other factors may cause problems, such as recording failure, recorded data corruption or loss. Canon shall have no liability whatsoever for any loss or damages incurred by the user as a result of such problems.
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or your national laws implementing those Directives.
This product should be handed over to a designated collection
point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE.
Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/environment
(EEA: Norway, Iceland and Liechtenstein)
.
iii
Introduction
MPEG-4
NOTICE ABOUT THE MPEG-4 VISUAL STANDARD: THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON­COMMERCIAL USE OF A CONSUMER TO (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON­COMMERCIAL ACTIVITY. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND ADDITIONAL LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM
This product is licensed under AT&T patents for the MPEG-4 standard and maybe used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard.
.
Third Party Software
The product (VB-C500D and bundled VK-Lite Viewer) contains third party software modules. For detail information, please see ReadMe-E.txt on the supplied Setup CD-ROM. Each module’s license conditions are also available in the License folder on the same Setup CD-ROM.
Software under GPL and LGPL
If you would like to obtain the source code under GPL/LGPL, please contact the dealer where you purchased the product, or a sales agent.
iv

Contents

Introduction ..............................................................................................ii
Checking of Bundled Items .................................................................... vii
Operation Manuals .......................................................................................... viii
How to Read This Document ..................................................................ix
Symbols Used for Safety Precautions ............................................................... ix
Safety Precautions .................................................................................. x
Maintenance ..................................................................................................... xv
Chapter 1 Before Use
Features of VB-C500D ......................................................................... 1-2
Bundled Software ................................................................................. 1-5
VB Initial Setting Tool Ver. 5.0 ........................................................................ 1-5
VBAdmin Tools Ver. 5.0 ................................................................................. 1-5
VB-C500 Viewer Ver. 1.0 ................................................................................ 1-6
Network Video Recorder VK-Lite v2.1 ............................................................ 1-6
Operating Environment ...................................................................... 1-11
VB Initial Setting Tool Ver. 5.0, VBAdmin Tools Ver. 5.0,
VB-C500 Viewer Ver. 1.0 .......... 1-11
Network Video Recorder VK-Lite v2.1 .......................................................... 1-11
Notes on Operating Environment ....................................................... 1-13
Notes on Use When the [Windows Firewall] Function is Enabled ............... 1-13
Notes on Use with Windows Server 2003/Windows Server 2008 ................ 1-14
Notes on Use with Windows Server 2008 .................................................... 1-16
Notes on Use with Windows Vista ................................................................ 1-18
Name and Function of Each Part ................................................................. 1-19
Optional Items .................................................................................... 1-22
Audio Interface Cable WA500-VB ................................................................ 1-22
I/O Interface Cable WC500-VB .................................................................... 1-23
Power Interface Cable WP500-VB ............................................................... 1-23
Recessed Mounting Kit SR500-S-VB ........................................................... 1-24
AC Adapter PA-V17 ..................................................................................... 1-24
VK-Lite Additional Viewer License ............................................................... 1-24
Network Video Recorder VK-64/VK-16 v2.1 ................................................. 1-25
v
Contents
Chapter 2 Initial Setting and Installation of Camera
Flow of Setup ....................................................................................... 2-2
Step 1 Install the Software ................................................................... 2-4
Install the Necessary Software ....................................................................... 2-4
Step 2 Connect the Camera to the Network ........................................ 2-6
Connect the Camera to the Network and Turn On the Power ........................ 2-6
Step 3 Perform Initial Setting of the Camera ..................................... 2-10
Perform Initial Setting of the Camera ........................................................... 2-10
Check the Video Captured by the Camera .................................................. 2-13
Step 4 Install the Camera .................................................................. 2-15
Installation Procedure for Direct Mounting on a Ceiling/Wall ....................... 2-16
Installation Procedure for In-Ceiling with a Ceiling/Wall .............................. 2-25
Chapter 3 Appendix
External Dimension Drawing ................................................................ 3-2
VB-C500D ...................................................................................................... 3-2
Recessed Mounting Kit SR500-S-VB (Option) ............................................... 3-2
Main Specifications .............................................................................. 3-3
Input/Output Terminals ........................................................................ 3-5
External Device I/O Terminals ........................................................................ 3-5
Audio Input/Output Terminals ........................................................................ 3-7
vi

Checking of Bundled Items

This product comes with the following items. If any item is missing, contact the store where you
purchased the product.
1. VB-C500D main Unit 2. Safety wire 3. Ceiling mount template
4. Setup CD-ROM 5. Start Guide (This document)
6. Warranty Card (different depending on the region)
Content of Setup CD-ROM
ReadMe-J.txt : Japanese text covering notes, etc. not included in this document
ReadMe-E.txt : English text covering notes, etc., not included in this document
Manual : Folder containing operation manuals (Japanese, English) other than
this document *
VBTools : Folder containing the installers for other bundled software (two installers
specified below)*
VBToolsInstall.exe : Installer for VB Initial Setting Tool and VBAdmin Tools*
VKLiteInstall.exe : Installer for Network Video Recorder VK-Lite*
License : Folder containing licenses for the built-in software of the VB-C500D as well
as bundled software VK-Lite
Sound : Folder containing sample audio files
* Check our website for the latest versions of bundled software and operation manuals.
vii
Checking of Bundled Items

Operation Manuals

The VB-C500D comes with Start Guide (this document) and Operation Guide included in the
Setup CD-ROM.
Start Guide (This Document)
The safety precautions to be followed when using the VB-C500D, types of bundled
software, operating environment, installation method, initial setting of the camera,
installation method, etc., are explained.
Operation Guide (VBC500DOG_E.pdf)
This document explains the basic setup procedure for the VB-C500D, how to use
VBAdmin Tools and VB-C500 Viewer, troubleshooting, etc. Items that should be
referenced in this document are denoted by "Operation Guide."
Operation Guide is included in the Setup CD-ROM.
Also, a simplified version of recording software VK-Lite (P. 1-6) is stored in the Setup CD-ROM.
The following operation manuals are available:
Setup Guide (VK21SUG_E.pdf)
This document explains the items to note when using VK-Lite, operating environment,
system configuration, installation method and setup method.
Administrator’s Manual (VK21AM_E.pdf)
This document explains details on how to use VK-Lite. Be sure to read this document.
Viewer Operation Guide (VK21VOG_E.pdf)
This is an operation guide for the VK-Lite viewer. For the detailed operating procedures of
the viewer, refer to Administrator’s Manual.
viii

How to Read This Document

In Start Guide and Operation Guide, screens in Windows Vista are mainly used. Unless otherwise
specified, the same screens apply to Windows XP.

Symbols Used for Safety Precautions

In this document, the following symbols are used to indicate important items the user should
know to use this product safely. Be sure to observe these items.
Symbol Meaning
Inappropriate handling against the instruction accompanied by this
Warning
Caution
Note
Note
Tip
symbol may result in death or injury. Be sure to observe this
precaution to use the product safely.
Inappropriate handling against the instruction accompanied by this
symbol may result in injury. Be sure to observe this precaution to
use the product safely.
Inappropriate handling against the instruction accompanied by this
symbol may result in property damage. Be sure to observe these
precautions.
This symbol indicates other action or item that requires
attention.
Supplementary information or a reference to the operation is
explained. Users are recommended to read these memos.
ix

Safety Precautions

The following explains the items that must be observed when using the VB-C500D.
If they are not observed, injury, death and/or property damage may occur. Read the following
information carefully and observe the instructions without fail.
Important Warnings
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
For optional PA-V17 Users in the UK
When replacing the fuse only a correctly rated approved type should be used and be
sure to re-fit the fuse cover.
The AC adapter can be connected to VB-C500D from a standard AC power outlet.
Please check your instruction manual to make sure that your VB-C500D is compatible
with this adapter.
• The socket-outlet should be installed near the equipment and should be easily
accessible.
• Unplug the equipment from the wall outlet before cleaning or maintaining.
FDA regulation
This Network Camera has not been evaluated by the Food and Drug Administration
(FDA) for use as a medical device. When incorporated into a system with medical
applications, FDA regulations may apply. Therefore, please consult your legal advisor
to determine whether FDA regulations apply.
x
Safety Precautions
FCC NOTICE
Network Camera, Model Name: VB-C500D
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you could
be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
xi
Safety Precautions
Precautions for Installation
Warning
Do not install the product in the following places:
• Place receiving strong direct sunlight, near heat generating objects, or subject to high temperature
• Place near fire sources or flammable solvents (alcohol, thinner, etc.)
• Humid or dusty place
• Place subject to lamp black or steam
• Place subject to sea wind
• Narrow, sealed place
Fire or electric shock may result.
Note
For installation or inspection of the VB-C500D, consult/request the store where you purchased the product.
• Wire the VB-C500D power supply, network, or other cables safely and securely according to the relevant regulations such as technical standards for electrical installations.
• When installing the VB-C500D, select a ceiling surface, etc., capable of withstanding the total weight of the camera and all options used (Recessed Mounting Kit), provide sufficient reinforcements and use the bundled safety wire if necessary.
• To prevent injuries and equipment damage due to falling items, periodically check the brackets and screws for rusting and loosening.
• Installation in a place subject to significant vibration is not recommended, because it may cause the equipment to malfunction.
• Do not install the VB-C500D on an unstable or inclined surface.
• Do not carry the product while the LAN cable or other cables still connected to it.
Malfunction may occur.
xii
Safety Precautions
Precautions for Use
Warning
• If smoke, abnormal noise, heat, odor or any other abnormality is detected, immediately stop using the camera and contact your nearest Canon dealer.
Continuing to use the product may result in fire or electric shock.
• Do not disassemble or modify the camera.
• Do not put water or other liquid in the camera or splash or otherwise wet the camera.
• Do not put foreign objects in the camera.
• Do not use sprays of flammable gases near the camera.
• When the camera is not used for a long period, disconnect the LAN cable, external power supply and power connector for AC adapter (optional) from the camera.
Fire or electric shock may result.
Note
• Do not use this camera for medical devices and other systems that affect human life.
Delayed or missing image transmission may occur depending on the PC and network environment, and thus high image transmission accuracy cannot be assured. Canon will assume no liability for any accident or damage resulting from use of the VB-C500D in the aforementioned devices or systems.
• Do not capture the sun, halogen lamps and other very bright light sources or subjects.
• Do not apply impact on the camera.
Malfunction may result.
This installation should be made by a qualified service person and should confirm to all local codes.
xiii
Safety Precautions
Notes on Use of Motion Detection, Stream for Recording and Bundled Recording Software VK-Lite
Note
• Avoid using Motion Detection, Stream for Recording or recording software VK-Lite for surveillance where very high level of reliability is constantly required.
These are support functions for monitoring. They do not guarantee monitoring with very high accuracy, however, as they might not work as accurately as expected under certain conditions. Canon will assume no liability for any accident or damage resulting from use of these functions.
Precautions for Use of Optional AC Adapter PA-V17
Warning
• Do not use any AC adapter or AC cable other than the dedicated AC adapter or AC cable.
• Do not put heavy objects on the power cable.
• Do not pull, forcibly bend, scratch or modify the power cable.
• Do not cover or wrap the AC adapter (optional) with a cloth or thick cotton blanket.
Fire or electric shock may result. Be sure to read the operation manual for PA-V17 before use.
Notes on Cleaning
Warning
• Do not use alcohol, thinner, benzene or any other flammable solvent.
Fire or electric shock may result.
xiv
Safety Precautions

Maintenance

Turn off the power before cleaning the camera (P. 2-7).
Cleaning of Exterior
1. Dampen a soft cloth with water or diluted neutral detergent and wipe the soiled areas gently.
2. Wipe with a dry cloth.
Cleaning of Lens
Use a commercial lens cleaner to remove soiling on the lens surface.
Scratches on the lens surface may result in undesirable images.
Maintenance for Dome Case
A soiled dome is a cause of poor image quality, so clean the dome periodically.
1. Remove the dome by referring to "Installation Procedure for Direct Mounting on a Ceiling/
Wall" (P. 2-16) in Chapter 2, "Initial Setting and Installation of Camera".
2. Dampen a soft cloth with water or diluted neutral detergent and wipe the soiled areas gently.
3. Wipe with a dry cloth.
4. When you are done, install the dome case.
To prevent injuries and equipment damage due to falling items, periodically check the brackets
and screws for rusting and loosening.
For checkups, please contact the dealer where you purchased the product.
Maintenance for Recessed Mounting Kit (Optional)
To prevent injuries and equipment damage due to falling items, periodically check the brackets
and screws for rusting and loosening.
For checkups, please contact the dealer where you purchased the product.
xv
Safety Precautions
xvi
Before Use
The following explains the features of this camera, bundled software,
operating environment, and name and function of each part.

Features of VB-C500D

The VB-C500D is a compact network camera for indoor installation integrating camera and server
features.
Wide-angle Varifocal Lens
Equipped with a wide-angle varifocal lens with a wide angle of 82°, F1.1 and optical 2.4x zoom (digital 4x), the VB-C500D achieves video monitoring in wide-ranging applications, including stores and offices, as well as applications in small areas such as at ATM and in elevator halls.
Compact Design Suitable for Various Installation Environments
The ultra-compact dome camera of 3.7 inches in size (dome diameter) can be installed inconspicuously in locations where appearance is given priority, such as in condominiums and hotel stores.
It can be installed in various ways, such as directly mounting on the ceiling, recessed into the ceiling, and mounting on a wall.
Capturing Color Images at 0.2 Lux
With its high imaging quality, the camera can capture color images at a minimum subject illumination of 0.2 lux while maintaining low noise and high color repeatability (when the 1/30­second Smart Shade Control is turned on).
Digital Night Mode Function to Automatically Adjust to
Capturing at Low Illumination
When the illumination is low, such as during nighttime, the capture mode is automatically switched from color to monochrome and Canon's unique low-noise, high-quality imaging technology is used to increase the digital sensitivity. If the Digital Night Mode function is used, images can be captured at a minimum subject illumination of 0.1 lux (when the 1/30-second Smart Shade Control is turned on).
Smart Shade Control
When the background is bright and the subject is difficult to see, you can change the contrast of dark areas to make the subject clearer. Unlike the backlight compensation, blown out of the background can be prevented because bright areas are not controlled. These processes are implemented by the dedicated hardware in the camera, so drops in image quality can be reduced and system load can be decreased compared to when the conventional shade control is used ( "Setting the Smart Shade Control in "Operation Guide").
PoE
The VB-C500D supports Power over Ethernet (PoE*) technology, which enables simultaneous video/audio data transmission and power supply by simply connecting a PoE HUB and a single LAN cable ( P. 2-6). When connecting to a PoE HUB, you need not connect a power adapter to the camera or perform any power wiring.
* PoE stands for Power over Ethernet, which is compliant with the IEEE 802.3af standard by the Institute of
Electrical and Electronic Engineers.
1-2
Features of VB-C500D
Install-Less VB-C500 Viewer
This camera has a built-in VB-C500 Viewer, so its data can be viewed using a browser. Accordingly, there is no need to install a PC application. Also, three levels of user privileges can be set, including [Administrator], [Authorized Users] and [Guest Users].
Canon's Network Video Processor "DIGIC NET"
The camera incorporates DIGIC NET that offers high network distribution performance and a range of intelligent functions to achieve high image quality and high-speed communication such as simultaneous distribution of JPEG and MPEG-4.
Simultaneous Distribution of JPEG and MPEG-4
Video compression adopts JPEG/MPEG-4 to achieve high image quality/high frame rate of up to 30 frames per second* simultaneously.
*1 Note that the frame rate may drop depending on the performance of the viewer PC, number of clients
connected at the same time, network load, etc.
*2 In MPEG-4, up to 10 clients can be connected at the same time.
1
in VGA (640x480). Up to 30 clients*2 can view the same image
Multi-Streaming
In JPEG, image can be distributed in three sizes (640x480, 320x240, 160x120) at the same time.
High Quality Video of Moving Subjects
The VB-C500D utilizes a progressive-scan CCD to allow for the capture of noise-less, high quality video of moving subjects.
1
1
Before Use
Selectable Metering Modes for Various Shooting Condition
Image can be captured by switching the metering mode* to one of three options, including Center-weighted, Average and Spot, according to the shooting condition of the camera. ( "Setting Exposure" in Operation Guide)
* Brightness (light quantity) of the subject is measured to adjust the exposure.
Uploading and Sound Playback by Motion Detection Function
Change in video caused by movement of the subject is detected to upload the refreshed image and play sound.
Upload, E-mail Notification
Events generated by the motion detection function or an external input device are used as triggers to upload images tentatively recorded in the camera to the specified location via FTP/ HTTP/SMTP (e-mail), or notify an event via HTTP/SMTP (e-mail).
1-3
Features of VB-C500D
Two-Way Audio (Full Duplex)
A microphone or speaker with amplifier can be connected*1 to the camera to transmit/receive audio (full duplex) via the viewer* and MIC IN by switching the setting on the setting page (P. 3-7).
*1 Microphones and amplifiers are sold separately. *2 VK-Lite Viewer is the only viewer that supports two-way audio communication.
VB-C500 Viewer only supports audio reception.
2
. You can select a desired audio input mode from LINE IN
Small-scale Video Monitoring by Simplified Recording Software
VK-Lite
This product comes with a simplifier version
Recorder VK-64/VK-16 v2.1
recorded/displayed in real time, to achieve small-scale video monitoring.
(P. 1-6). Video captured by up to four cameras can be
VK-Lite
of the optional
Network Video
1-4

Bundled Software

The VB-C500D comes with the software specified below.
For the latest information on this product (firmware, bundled software, operation manuals,
operating environment, etc.), visit our website.

VB Initial Setting Tool Ver. 5.0 ( P. 2-10)

VB Initial Setting Tool is for initial setting of the VB-C500D. It is installed from Setup CD-ROM (P. 2-4). Users other than Administrators need not install this tool.

VBAdmin Tools Ver. 5.0 ( Overview of VBAdmin Tools in Operation

Guide)
VBAdmin Tools are for visually setting motion detection and for displaying logs taken by the camera. It is installed from Setup CD-ROM (P. 2-4). Users other than Administrators need not
install this tool.
1
1
Before Use
1-5
Bundled Software

VB-C500 Viewer Ver. 1.0

VB-C500D Viewer is for displaying video captured by this camera and controlling the camera. Three users can be set according to the camera control rights, including [Administrator], [Authorized Users] and [Guest Users]. This tool is already built into the camera and need not be installed beforehand (P. 2-4). JPEG video captured by the VB-C500D can be displayed.
To d is p lay
MPEG-4 video, install VK-Lite Viewer (P. 1-7).
( Overview of VB-C500 Viewer in Operation Guide)
Note
To use the camera with VBAdmin Tools for the VB-C60, VB-C300 or VB-C50 series, install VBAdmin Tools for the VB-C50 series first, and then install VB-C300, install VB-C60, and finally install VBAdmin Tools bundled with the camera.
Tip
VB Initial Setting Tool Ver. 5.0 can be used commonly with the VB-C60, VB-C300 and VB-C50 series.

Network Video Recorder VK-Lite v2.1 ( Setup Guide)

VK-Lite v2.1, which is a simplified version of the optional "Network Video Recorder VK-64/VK-16 v2.1" (P. 1-25), is included in the package. VK-Lite consists of the following two software programs:
1-6
Software Configuration of VK-Lite
Bundled Software
Type Overview License
VK-Lite Storage Server Up to four cameras can be registered to record video. 1 license
Recorded video saved in the storage server can be
VK-Lite Viewer
VK-Lite Storage Server and VK-Lite Viewer can also be installed in, and run on, the same PC.
VK-Lite Viewer can also be used independently, without connecting to VK-Lite Storage Server.
Configuration example based on Configuration example with VK-Lite Viewer only
installation on the same PC
For VK-Lite, following cameras can also be registered and used.
played or live video (JPEG/MPEG-4) can be displayed as
it is captured by the camera. Up to four cameras can be
registered for the viewer.
VK-Lite Storage Server VK-Lite Viewer
1 license
VK-Lite Viewer
1
1
Before Use
Supported
cameras
VB-C500D, VB-C60/VB-C60B, VB-C300/VB-C300B
VB-C50i/VB-C50iR, VB-C50FSi, VB-C50Fi
Note
To add a VK-Lite Viewer, you need to purchase an optional "VK-Lite Additional Viewer
License".
1-7
Bundled Software
Key Functional Limitations of VK-Lite and VK-64/VK-16
Category Key functional limitation VK-Lite v2.1 VK-64/VK-16 v2.1
Camera
connection
Storage
server
Viewer
Maximum number of
cameras that can be
connected
Recording format JPEG
Normal schedule
Recording mode
recording (continuous
Manual recording
Maximum recording frame
rate
Maximum video retain
period
12 weeks (90 days) 999 weeks*
Registration of multiple
storage servers*
Number of displayable
2
No more than 8 is
video windows
4 units 64 units/16 units
JPEG
MPEG-4
Normal schedule
recording (continuous
recording, sensor
event recording,
recording)
motion detection
recording)
Special day schedule
recording
Manual recording
5 fps 30 fps*
recommended.
Not limited*
1
1
1
Layout Sequences*
*1 The maximum limit may be imposed depending on the number of cameras, PC performance and hard
disk space, network load, etc.
*2 When multiple storage servers are used, determine one master storage server. This way, cameras
registered for each storage server, recorded data, etc., can be managed centrally using the viewer. With VK-Lite, switch the storage servers one by one if multiple storage servers are connected to the viewer.
*3 This function allows the displayed viewer window to be switched at specified intervals.
3
1-8
Loading...
+ 56 hidden pages