Cannon Fitzroy Powerflue In-built, Fitzroy Inbuilt Power Flue Operation Instructions Manual
Power Flue
Cannon
FITZROY INBUILT
OPERATION INSTRUCTIONS
SERVICE INSTRUCTIONS
Gmk10030
AS4553:2008
This heater is approved for use with
Please leave instructions with the owner
Pa rt No : F304 5
Revision P - 2010
Cannon
For service to this appliance or spare
parts contact the CANNON distributor:
email: service@sampfordixl.com.au
Sampford IXL (spare parts)
Phone: 1300 727 421
Fax: 1300 727 425
FITZROY INBUILT
Natural and Propane gases.
DON’T RISK YOUR APPLIANCE WARRANTY
ONLY A LICENSED PERSON WILL GIVE YOU A COMPIANCE
CERTIFICATE, SHOWING THAT THE WORK COMPLIES WITH
ALL THE RELEVANT STANDARDS.
AND ONLY A LICENSED PERSON WILL HAVE INSURANCE
PROTECTING THEIR WORKMANSHIP FOR 6 YEARS.
SO MAKE SURE YOU USE A LICENSED PERSON TO INSTALL
THIS APPLIANCE AND ASK FOR YOUR COMPLIANCE
CERTIFICATE TO ENSURE THE MANUFACTURERS
APPLIANCE WARRANTY WILL BE HONOURED.
Power Flue
Date installed: ...............................................................................................
Compliance Certificate No .............................................................................
Installed by: ...................................................................................................
INSTALLATION NOTES
PLEASE READ THIS MANUAL
BEFORE INSTALLING
THIS HEATER.
28
COPY RATING LABEL HERE
INSTALLATION INSTRUCTIONS
NOTES
CONTENTS
2
To replace the combustion fan
Contents 2
Warranty 3
?
Distributor
Safety warnings 5-6
?
What to do if you smell gas
?
Warnings
?
Regulatory location 7
User instructions 8-9
?
Operating instructions
?
Cleaning
?
Flame characteristics
Heater specifications 4
Installation instructions 10 -13
?
Clearances
?
Fitment of cabinet depth spacer
?
Fitment of flue cowl
?
Preparing flexible flue pipes
?
Sealing the fascia
Gas connections 16
Log installation 17
Gas control 18-19
?
Gas pressure point
?
Gas pressure adjustment
Trouble-shooting 20-21
?
Service instructions 22-24
? General
? To replace the primary glass
? To replace outer glass
? To replace the gas control
? To replace the ignition (module) device
? To replace the room circulation fan
? To replace the fan pressure switch
?
?
To replace the burner and spark/sense electrode
? Wiring diagram
? Data plate
? Date installed, Compliance Certificate No.
? For service to this appliance
Front fascia removal
?
Electrical Connection 16
?
Flueing options
Standards
?
27
NOTES
WARRANTY
Don’t risk your appliance warranty
Only a licensed person will give you a Compliance Certificate,
showing that the work complies with all the relevant standards.
And only a licensed person will have insurance protecting their
workmanship for 6 years.
So make sure you use a licensed person to install this appliance
and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured.
Distributor
This appliance is designed, manufactured and distributed by:
Tel: 1300 727 421
3
26
The benefit conferred by this warranty are in addition to all other rights and
remedies in respect of the product that consumers have under the Trade
Practices Act and similar laws of the States and Territories.
We warrant this Cannon appliance to be free of defects in materials,
workmanship and manufacturing to the original purchaser for 2 years, (10 years
on the heat exchanger) from the date of original purchase. We will, at our
option and subject to the terms of this warranty, repair or replace free of charge
this Cannon appliance or any component part, which upon examination by us
or our repair agent is found to be defective in materials, workmanship or
manufacturing. However, this warranty does not cover any consumables (if any).
The purchaser must present the original purchase receipt to us when making
any claim under this warranty.
This warranty will not apply if: (i) a compliance label or serial number (as the
case may be) has been removed from the appliance or rendered illegible; (ii)
the appliance has been subject to misuse, abuse, accident, incorrect installation
or non-domestic use; (iii) the appliance has been modified, tampered with or
repaired by a person other than our authorised repair agent; (iv) the appliance
is re-installed/relocated during the warranty period.
The purchaser is responsible for all travelling expenses if the purchaser
requests any repair be carried out at a place outside areas normally serviced
by our repair agents.
Should you require service on this appliance, please contact our service
department on 1300 727 421.
Enter the details of the date installed and the Compliance Certificate number in
the appropriate area on the rear page of this manual.
FIG 1.
*(FOR I NSTALLATION I NTO A
MASONRY /BRICK FIREPL ACE)
HEATER SPECIFICATIONS
4
WIRING DIAGRAM
240 V MAINS PLUG
N
N
A
L
M
H
TH2
MOD1
MOD2
BLACK
WHITE
ORANGE
GREY
PURPLE
BROWN
BLUE
BLACK
BROWN
WHITE
BLUE
YELLOW/GREEN
8 WAY CONNECTOR
BLACK
BROWN
RED
RED
WHITE
RED
PRESSURE
SWITCH F3327
ROOM AIR FAN
NO
FUSE
BLUE
BLUE
ORANGE
GREY
PURPLE
YELLOW/GREEN
BLUE
MODULATING
VALVE F3691
COILS
1.5 AMP
ON/OFF
LW BRN / LW FAN
MED BRN / MED FAN
HIGH BRN / HIGH FAN
SHEATHED
CABLE
E
N
A
FLAME
SENSOR
SPARK
ELECTRODE
FUNCTION
CONTROL
MODULE
P/No. F3604
IGNITION MODULE
F3435
SWITCH
ROOM FAN - F3594
COMBUSTION
FAN - F3659
W
BLK
BRN
6 WAY CONNECTOR
6 WAY CONNECTOR
BLUE
4 WAY
F3663-6_B
NO
PRESSURE
SWITCH F3327
COMBUSTION FAN
POWER FLUE
WIRING DIAGRAM
COMMON
COMMON
4 WAY
25
Gas type:Natural or Propane gas, as indicated on data label
Gas consumption: 26.0 MJ/hr
Energy output: 5.98 kW
Enery star rating: 5.05 stars
Heater type: Gas space heater
approved to AS 4553:2008
Operating pressure: Natural gas: 0.75 kPa
(at burner high setting) Propane gas: 2.65kPa
Gas regulator: Integral part of controller
Min. inlet pressure: 1.13 kPa (NG)
2.75 kPa (Propane)
Fan: 3 speed
Controller: Electronic direct spark
Power requirement: 240 VAC 10 A
Power consumption: 90 VA maximum
Minimum cavity Height: 605 mm*
dimensions:Width: 700 mm
Depth: 485 mm
Optional accessories:
Glass front
Remote thermostat
Spacer kit
3 sided surround
4 sided surround
Console kit
Please read this manual before installing and using the heater.
SAFETY WARNINGS
What to do if you smell gas
1. Turn OFF the main gas supply.
2. Extinguish any open flame.
3. Open windows.
4. Do not touch electrical switches.
5. Do not use your telephone.
6. Call your gas supplier immediately from a neighbour’s phone.
Warnings
1. Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the sections of this manual for correct
procedures, or consult with place of purchase, a licensed plumber, a gas supplier
or the CANNON distributor listed in this manual.
2. Install the heater only in locations that are referred to in the installation instructions.
Do not build the heater into bookcases, walls or enclosures without the use of a
Mock Fireplace kit if appropriate for that type of installation.
3. Due to high temperatures the room heater should be located out of traffic and away
from:
Furniture and draperies
Combustible materials
Gasoline and other flammable liquids
Do not place clothing or other flammable material on or near the heater.
4. Keep curtains*, clothes, furniture and other flammable materials at least
900mm from front and sides of heater.
* At the owner’s discretion curtain clearance can be less than 900mm as
long as they are restrained from the front, top and sides of the heater. The
manufacturer takes no responsibility if curtain clearance is less than 900mm
and not restrained.
5. Children and adults should be alerted to the hazard of high surface temperature
and should take care to avoid burns or clothing ignition.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
6. Never attempt to burn paper or any other material in the heater.
7. Do not place articles on or against this appliance.
Do not use or store flammable materials near this appliance.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
Do not modify this appliance.
notes
TO REPLACE THE
COMBUSTION FAN
The Combustion Fan is accessed from the rear of the heater.
Therefore to replace the combustion fan the heater must be
removed from the fireplace. The flue terminal may need to be
removed from the flue hoses to allow the heater to be moved.
1. Disconnect combustion fan wiring from loom.
2. Remove the rear cover.
3. Remove the four (4) screws securing the fan to fan duct.
4. Remove fan assembly from fan duct.
5. Replace in reverse to disassembly.
TO REMOVE THE BURNER
AND ELECTRODES
TO REPLACE TYPE “X”
CORD
1. Remove the front mesh cover.
2. Slacken off the glass clamp screws and remove the
top and one side clamp.
3. Follow fig 25. of the installation instructions
for glass removal.
4. Remove the logs from the burner chamber.
5. Remove the inspection hatch cover.
6. Disconnect supply pipe nut from the burner manifold.
7. Remove the electrode connections from the spark
module.
8. Release gland seal retaining nut.
9. Remove burner fixing brackets (2) from rh and lh
sides of the burner. lift the burner assembly upwards
and carefully remove from the burner chamber.
10. Pull electrode leads from the gland seal.
11. Replace in reverse order.
1. CONTACT SAMPFORDIXL SERVICE DEPARTMENT AND QUOTE CORD
PART NUMBER F2799.
SERVICE INSTRUCTIONS
24
5
FIG 31.
Loading...