Canko Technologies LFETMENA, PLTNUMNA, FSIRNA5400 Users Manual

Safety Instructions
Please read this User’s Manual before starting the operation of the receiver.
Never open the cover. It is dangerous to touch the inside of the receiver due to possible
electric hazard.
When the receiver is unused for a long time, unplug the power cord from the wall outlet.
Do not touch the power cord with wet hands. It may cause an electric shock.
Place the receiver in a well-ventilated environment. Avoid extreme temperatures.
When connecting cables, the receiver must be powered off.
Do not expose the receiver to flames, such as placing a candle on top of the receiver.
Do not expose the receiver to possible dripping or splashing of liquids. For example, do
not place a vase with water in it, on or near the receiver.
How to Use This Manual
This manual provides instructions for installing and using this receiver. The following symbols are used in the manual:
MENU
(Bold Character) Represents a button on the remote controller or the receiver.
Move to
(Italic Character) Represents a menu item within a window.
Indicates warning information.
Indicates any other additional important or helpful information.
IMPORTANT SAFETY INSTRUCTION
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instruction.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two bl ades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at the receptacle, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
1
2
Contents
1. Before You Begin
1.1 Features
1.2 Accessories
2.Controls and Functions
2.1 Front Panel
2.2 Remote Control Unit
2.3 Rear Panel
3.Connections
3.1 Connecting to a TV & VCR
3.2 Connecting to the Dish
3.3 Connection to a CAS / CI Module (for applicable models)
4.Settings and Operations
4.1 Before Settings
4.2 Basic Settings
4.3 Menu in the Normal view mode
4.4 Managing Channel Data
4.5 System Setup
4.6 Preferences
4.7 Name Editing
Additional Information
A.1 Trouble Shooting A.2 Specifications A.3 Glossary of Terms
Before You Begin
1.1 Features
Basic Features:
Easy-to-use Graphic MENU Interface
RS232 Port for Updating Software and Additional Services
Supports DiSEqC1.0/1.2, 13/18V, 22Khz Tone
S-Video Connector & 3-RCA Connectors
S/PDIF Connector for AC3 audio pass-through
Multi-language Functionality (Menu, Audio)
Last Channel Memory (on the same satellite)
OSD: Transparency & Blending, 256 Palette Colors
Front Panel Buttons & IR Remote Controller User Interface
Editing Functions (TV or Radio Channel: Channel Name, Favorite Name, Satellite Name)
EPG for On Screen Channel Information (where available)
Channel Memory for Multi-satellites (up to 64)
3 Operation Modes (Digital TV, Digital Radio, Favorite)
Digital Features:
Receives QPSK Satellite Broadcasting RF Signal and Decodes the Digitally Encoded Signal.
Digital Tuner with Loop-through output
SCPC/MCPC Receivable from C/KU-band Satellites
MPEG-2 Main Profile at Main Level
Teletext Supported Through VBI & OSD
4,800 Channel Memory
CI Features: (For CI model only)
DVB Common Interface (Viaccess, Nagra Vision, Conax, Irdeto, Cryptowrks, ASTON)
Embedded CAS Features: (For embedded CAS model only)
One Irdeto Embedded slot
3
4
1.2 Accessories
User’s Manual
Remote Control Unit
Batteries
2. Front Panel
2.1 Front Panel
1. Power Button
Please don’t recharge, disassemble, electric short, or mix with used or other battery types.
Figure 1. Accessories
Turns the receiver On/Off.
2. Channel UP/DOWN Button
Moves the cursor up/down in Menu state. Changes the current program to the
next/previous program in the Non-menu state.
3. Volume -/+ Button
Increases/decreases the volume levels in the Non-menu state. Change the setting
values in specific Menu items.
4. Display (4-digit, 7-segment / 3LED)
The 4-digit panel displays channel information. In STAND BY mode, the 7-segment panel
displays local time.
The red LED is the STAND BY indicator and the green LED is the CAM-in indicator (CI
Model Only). The other green LED is the Card-in indicator for CAS models.
5. CI Slot (CI Model Only)
Insert CI module into CI slot for conditional access.
For Embedded CAS models (i.e., Irdeto embedded), the card slot will appear beside the CI slot position.
Figure 2. Front Panel
5
6
2.2 Remote Control Unit
All features of the set-top box can be controlled with the remote controller.
1. POWER Turns the receiver On/Off.
2. MUTE Mutes audio output of the receiver.
3. TV/SAT Switches RF modulator output to receiver output or ANT input. Whenever the TV/SAT button is pressed, the RF modulator output is changed to receiver video/audio output or bypass the ANT input signal.
4. NUMERIC KEY(0-9)
Controls the numerical operations, and changes the program channels directly.
5. SAT Shows the satellite list and the channels downloaded for that satellite.
6. TV Shows the current digital TV program list.
7. RADIO Shows the current digital Radio program list.
8. FAV()
Shows the current favorite program list.
9. TEXT Shows Teletext information for the channel if available.
10. RECALL Shows previous channel (only on the same satellite).
11. UP/DOWN
Change the current program to the previous/next program in Non-menu state. Moves the cursor to upward/downward in Menu state.
12. P+/P-
13. OK Activates the highlighted menu item. Or, view the program guide in Non-menu state.
14. LEFT/RIGHT
Change the setting value in certain Menu fields.
15. INFO Normally used for viewing channel information.
16. MENU
Shows the menu or sub-menu and cancels the processing function if applicable.
17. EXIT
Exits from the menu or sub-menu and cancels the progressing function if applicable.
18. LANG
Shows the list of the audio languages available for the current channel.
19. PAUSE
Pause the video/audio output. (Not a PVR function.)
20. EPG View the program guide in Non-menu state, if available.
21. SOUND
Select sound mode. (Stereo or mono).
Page up and down in menu list.
2.3 Rear Panel
1. LNB IN
Connect the digital signal from your LNB of your satellite dish to this connector.
2. LOOP OUT Gives you the possibility to connect an extra receiver (analogue or digital).
3. VIDEO (Yellow RCA)
This connector has a constant video signal for additional VCR-connections, or to the TV.
4. AUDIO Right (Red RCA) and Left (White RCA) These connectors give you the possibility to connect the audio signal to an external amplifier, or to the audio inputs of your TV.
5. S/PDIF (AC3 Dolby Digital Pass-through)
Used to connect a digital audio amplifier to your receiver using a Toslink cable.
6. S-VIDEO
Provide better picture quality than above video out (yellow RCA).
If your general TV (analog TV) has S-VIDEO capability, use this jack along with the Audio RCA jacks to connect the receiver to your TV.
7. RS232 Serial Port This serial port can be used to connect your PC to your receiver, which enables you to download new versions of software into your receiver. (Note: Changing the software voids the manufacturing warranty.)
8. ANT
If you have an additional antenna (cable or terrestrial), it can be connected here. This allows you to select the additional antenna using the satellite receiver remote.
9. TV/VCR RF Modulator can be used to connect the receiver to your TV, using a coax cable. If you connect your receiver to your TV like this, be sure that you set your TV to the correct channel number. The yellow RCA connector or the S-Video connect will provide a better video quality.
10. Power Cord
Your receiver requires a current of 100~120V AC, 60Hz. Make sure to check the power specification before connecting your receiver to the wall outlet.
7
8
3. Connecting to the TV&VCR
3.1 Connecting to the TV & VCR
Basic Connection
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the TV/VCR connector at the back of the receiver to the coax IN connector on
your TV set.
3. Connect the RCA connectors at the back of the receiver to the RCA in connectors on your TV set for better picture quality. Or, also use the S-Video connector for the best picture quality (not shown in diagram).
4. Optional: Connect an extra terrestrial or cable antenna to the ANT connector at th e back
of the receiver.
Advanced Connection of the Receiv er to the TV set, VCR and Audi Amplifier
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the audio S/PDIF OUT on the back of the receiver to the S/PDIF input of an
Audio Amplifier (Dolby Digital decoder).
3. Connect the RCA connector on the back of the receiver to the RCA IN connector on your VCR set.
4. Connect an extra terrestrial or cable antenna to the ANT connector on the back of the receiver.
3.2 Connecting to Dish
Aiming a satellite dish and LNB with the correct longitude and azimuth (angle of elevation) at a satellite is a specialist job, which a professional installer can do best.
Connecting a fixed satellite dish to your receiver
Make your choice of which satellite you want to receive your signals from, and have your installer aim your dish at the required satellite. Connect a coax cable from your LNB with the other end going directly to the LNB IN connector of your receiver.
9
10
Loading...
+ 12 hidden pages