Candy LB CTS 40 SY User Manual

WASHING MACHINE CANDY CTS 40
C1
A PROGRAMME & TEMPERATURE SELECTOR DIAL C1 HOT/ COLD KEY C2 LIGHT LOAD KEY H START/STOP KEY p CONTROL POSITION INDICATOR
1/2
pC2 H
Programme table mod. CTS 40
Mains
voltage
Wash power rating
Spin power rating
Pump motor power rating
Heating element
power rating
Max.
power
input
Mains fuse amp. rating
Water
pressure
Water
consumption
* prog.
EN 60456
Energy
consumption
* prog.
EN 60456
230 V. /
50 Hz.
175 W. 340 W. 30 W. 1950 W. 2200 W. 10 A. 0,05-0,8
Mpa
69 L. 1,35 Kw/h.
programme
programme programme for
SPECIAL
selection
32´
32' express
1
heavily soiled cotton
2
soiled cotton
3
*cottons
4
coloured
COTTONS
DELICATES
MIXED /SYNTHETICS
bleach (organic stains) vigorous rinse vigorous spin
5
mixed garments
6
coloured
7
acrylic
8
Woolmark certified woollens delicate rinse stop with water in drum delicate spin empty
aprox.
time min.
32 180 120
85
70
55
43
10
80
70
65
50
25
7 5
Máx. temp.
setting
ºC
50º 90º 90º 60º 40º
60º 50º 40º 40º
Máx. spin
speed
400 400 400 400 400 400 400 400 400 400 400 400 400
400
Máx.
Washing powder load
load
kg
I II
2
5 5 5 5
2 2 2 1
*Programme as per EN 60456
Option keys C
1/2
Technical data mod. CTS 40
PREPARING THE WASH CYCLE
1.- Once the washing is loaded, ensure that the drum doors are properly closed.
2.- Add detergent and additives, not exceeding the maximum level indicator. .- detergent for pre-wash I .- detergent for wash programme II .- bleach .- fabric conditioner
SELECTING THE DESIRED PROGRAMMES AND OPTIONS
3.- Turn the programme selector dial (A) to the desired programme (clockwise only)
4.- Press the key or keys for any options desired (C1, C2 ).
C1 hot/ cold key
If this key is pressed the heating element is not connected, i.e. the machine washes cold. This works in all programmes.
C2 light load key
Press this key to lower the water level for light loads, thus saving water, detergent and electricity.
5.- Once you have selected the desired options, press the Start key (H).
To cancel an option selected, just press the key again.
To change or cancel a programme
To change or cancel a programme once the programme selected has started, proceed as follows:
- Press (H). The programme has been cancelled, and another may be selected.
- Select the new programme.
- Press (H) again.
- The machine will then run the new programme selected.
Programme pause
To pause the wash programme so that more washing can be added, proceed as follows:
- Press (H). When the door safety loc k is released (after approx. 2 minutes), open the door and add more clothes as required.
- Close the door and press (H) again.
- The machine will continue with the programme.
Fast programme –32 minutes
The 32-minute fast programme runs through a full cycle for up to 2 kg of washing at 50 ºC. Place detergent in the tray (compartment I), using no more than around _ of the recommended quantity. The 32-minute fast programme can also be used as a pre-wash pr ogramme for heavily soiled clothes by then selecting the desired main programme.
NB
In MIXED, COLOURED, ACRYLIC & WOOL programmes the machine stops with water in the drum at the end of the last rinse due to the easy-iron feature. To complete the cycle by spin washing, turn the programme dial one step forward.
To complete the cycle by merely emptying the machine, select the (empty) programme.
END OF PROGRAMME For safety’s sake, when the programme ends set the Start/Stop key to Stop.
10-04 / 46001941 EN
Loading...