Page 1
CDI454-S
Page 2
This manual contains sections of Safety
Instructions,Operating Instructions,
Installation Instructions and Troubleshooting
Tips etc. Carefully reading it before using the
dishwasher will help you to use and maintain
the dishwasher properly.
To review the section on TroubleshootingTips
will help you to solve some common problems
by yourself and not need to ask for the help of
professional technicians.
..................1
ControlPanel........................2
DishwasherFeatures................. 2
WashCycleTable.................... 3
WaterSoftener...................... 4
Detergent...........................5
RinseAid......................... 5,6
Loading the Dishwasher Rack . . . . . . . . 6,7
TurningOntheAppliance..............7
FilteringSystem..................... 8
CaringfortheDishwasher.......... 9...
The manufacturer, following a policy of constant
development and up-dating of the product, may
make modifications without giving prior notice.
AboutElectricityconnection . .. . . . . . .. 9
AbouttheUnicouple.................10
WaterConnection...................10
Beforecallingforservice.......... 12
Page 3
Under certain conditions, Hydrogen gas may be produced in a hot-water system thathas not been
used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If thehot-water systemhas not been used for such aperiod, before using the dishwasher turn on all
hot-water faucets and let the water flow from each for several minutes. Thiswillrelease any
accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this
time.
This appliance complies with international
safety standards, and is fitted with aplug with
earthconnectiontoensurecompleteearthing
of the product.
Before connecting the appliance to the mains
supply it is important to ensure:
That the supply socket is properly earthed.
That your electricity supply is capable of
meeting theconsumption requirements
listed on the rating plate of your appliance.
Ensure that your product is properly earthed. In the
absence of adequate earthing you willnotice that when
touchingthe metalparts of yourappliancean
electrical dispersion can be felt, due to the presenceof
a radio interference suppressor.
This appliance complies with Directives
89/336/EEC, 73/23/EEC and following changes.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
Do not wash plastic items unless they are marked
dishwasher safe or the equivale nt. For plastic
items not so marked, check the manufactures
recommendations.
Use only detergent and rinse additives designed
for an automatic dishwasher. Never use soap ,
laundry detergent, or hand washing detergent
in your dishwasher. Keep these products out of
children.
Keep child away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
The door should not be left in the open position
since this could present a tripping hazards.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The applianceis not intended for use by young
children or infirm persons without supervision.
Dishwasher detergents are strongly alkaline,they
can be extremely dangerous if swallowed.Avoid
contactwithskinandeyesandkeepchildrenaway
from the dishwasher when the door is open.
Important: when the appliance location is on carpet
floors,attention mustbe paidso as to ensurethat
there is no obstruction to the bottom vents.
Do not operate your dishwasher unless all
enclosure panels are properly inplace. Open the
door very carefully if the dishwasher is operating,
there is a risk of water squirting out.
Do not place any heavy objects of stand on the door
when it is open. The appliance could tip forward.
When loading itemsto be washed:
1) Locate sharp items so thatthey are not likely to
damage the door seal;
2) Load sharp kniv es with the handles up t o reduce
the riskof cut-type injuries.
When using your dishwasher, you should prevent
plasticitem from contacting with heating element.
If the supply cord is damaged, it mustbe replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Young children should be supervised to ensure that
they do not play with the appliance.
Check that the detergent receptable is empty after
completion of the wash cycle.
Cutlery is washed best if it is placed in the basket with
handles downwards.
Warning:
knives and other utensils withsharp points must be
loaded in the basket withtheir points down or placed in a
horizontal position.
1
Page 4
To get the best performance from your dishwasher,read all operating instructions before using it for the
first time Keep this booklet safe for future reference.
1 2
Program indicator light:when you select washing
1
program,the correspond light will display.
Program Key-press:To selecte washing program
2
when press the Prongram Key-press.
Salt and Rinse Aid Warning Light: To come on when
3
the softener or dispenser needs to be refilled
(Certain model only).
3
1
4
Delay start time:To display booking time or the
4
washing temperature.
5
Delay key-press:The key to set the delay start
time.
Poweronlight:TocomeonwhenPowerON/OFF
6
Bouton is pressed down.
ON/OFF Button:To turn on/off the power supply.
7
6
5
7
7
2
3
4
5
6
1
2
3
Upper Basket
Spray Arms
Lower Basket
8
9
10
4
Water Softener
5
Detergent Dispenser
6
CupShelf
7
Silverware BasketMain Filter
8
Coarse Filter
9
2
11
10
Rinse Aid Dispenser
Drain pipe connector
11
Inletpipe connector
12
12
Page 5
Normal
(EN 50242)
For normall y soiled loads,
such as , plates,glasses
and lightly soiled pans.
standard daily cycle.
pots
Pre-wash
Wash (50℃)
Rinse (65℃)
Drying
4/20 gr.
Strong
Economy
1Hour
Delicate
Rapid
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that hav e
been sitting with dried food
on them for a while.
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
Daily wash in only 1 hour.
Suitable for normal soiled dishes
that are to be washed straight
after a meal (max 6 plate settings).
For lightlysoiledloads,
such as glasses, crystal and
fine china.
A shorter wash for lightly
soiledloads(max4platesettings).
Pre-wash
Pre-wash (45℃)
Wash (70℃)
Rinse (75℃)
Drying
Pre-wash
Wash (45℃)
Rinse (65℃)
Drying
Pre-wash (30℃)
Wash (70℃)
Rinse (65℃)
Drying
Wash (45℃)
Rinse (65℃)
Drying
Wash (50℃)
Rinse (55℃)
Drying
8/24 gr.
4/20 gr.
20 gr.
20 gr.
15 gr.
Soak
Your dishwasher has an overfill protection device which could automatica lly shuts off the inlet valve and starts the drain pump
if the water overflow. If this occurs, turn off the main water supply before calling a servicing. If there is waterin the basepan
because of an overfill or small leak, the water should be removed before restarting the dishwasher.
To rinse dishes that you
plan to wash later that day.
Pre-wa sh
3
Page 6
If your model have not water softener, you may skip this section.
There are two ways to reduce the hardness: one way is using water softener, the other is using
water
detergent.
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliances is equipped with a specialsoftener that uses a salt specifically designed to eliminate lime and minerals from the
water.
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as follows:
Remove the lower basket and then unscrew and remove the cap from the salt
1
container.
If you are filling the container for the first time ,fill 2/3 of its volume with water.
2
3
Place the end of the funnel(supplied) into the hole and introduce about 2kg of
salt .It is normal for a small amount of water to come out of the salt container
4
Carefully screw the cap back on.
1.
The salt container must be refilled when the salt warning light comes on. Though the salt container is filled
enough, the indicator light may not black out before thesalt fully dissolve.
2.
If there are spills of the salt, a soak program could be run to wipe them out.
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used.
This is intended to optimize andcustomize the levelof salt consumption so thatthe salt consumption could be set proceedas
follows:
Unscrew the cap from the salt container.
1
There is a ring on the container with an arrow on it (see Figure to the side), if
2
necessary, rotate the ring in the anticlockwise direction from the "-" Setting
toward the "+" sign, based on the hardness of the waterbeing used.It is
recommended that adjustments should be made in accordance with the following
schema:
WATER HARDNESS
°fH
0~10 0-5 0-1.0
10~25
25~50 14-28 2.5-5.0 MED 40 40
>50 >28 >5.0
dH
5-14 1.0-2.5
mmol/l
Selector
Position
-
/
+
Salt consumption
(gram/cycle)
0
20 60
60 25
Auto nomy
(cycles/2kgs)
/
Contact your local water board for information on the hardness of your water supply.
4
Page 7
YOU MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOURDISHWASHERS
HAVE SPECIALLY-DESIGNED WATER SOFTENERS.
The dispenser must be refilled before the start of each wash cycle following the instructions provided in the" WashCycle
Table".Your dishwashers than conventional dishwashers. Generally, only one tablespoon of
detergent is needed for a normal wash load. Also, more heavily soiled items need more detergent. Always add the detergent just
before starting dishwasher,otherwise it could get damp and will not dissolve properly.
IF THE WATER ISN'T TOO HARD, YOU MAY ALSO PREVENT THE FORMATION OF DEPOSITS BY ADDING DETERGENT.
The amount of detergent needed can vary due to differencesin waterhardness. To determine the water hardness in your area,
contact your local water utility or area water softening company. The harder the water, the more detergent you may need.
Remember, you should adjust the amount of detergent you use by small amounts until you find the correct amount.
use less detergent and rinse aid
To remove har d water spots, try the following:
Run dishes through a normal wash program.
Remove all metal dishware, such as cutlery, pans, etc.,
from the dishwasher.
Do not add detergent.
Pour twocups of vinegar into a bowl and set the bowl face
up on the lower rack of the dishwasher.
Runthe dishes through a normal wash program.
If this doesn't work, try the same process with 1 / 4 cup of
citric acid crystals instead of vinegar.
Dishwasher detergent is corrosive! Take care to keep it out
of reach of children.
To open the dispenser, turn the cap to the "open" (left)
arrow and lift it out.
Pour the rinse aidinto the dispenser, being careful not to
overfill.
Replace the cap by inserting it aligned with "open" arrow
and turning it to the closed (right) arrow.
Use only detergent specifically made for use in dishwashers.
Keep your detergent fresh and dry. Don't put powde r detergent
into the dispenser until You're ready to wash dishes.
The rinse aid is released during the final rinse to prevent water
from forming droplets on your dishes thatcan leave spots and
streaks. It also improves drying by allowing water to "sheet" off
the dishes.
Your dishwashe rs are designed to use liquid rinse aids. The
rinse aid dispenser is located inside the door next to the
detergentdispenser. To fill the dispenser, open the cap and
pour the rinse aid into the dispenser until the level indicator
turns completely black. The dispenser holds about 100 ml of
liquid rinse aid.
Be careful notto overfill thedispenser, because thiscould
cause oversudsing. W ipe away any spills with a damp cloth.
Don't forget to replace the cap before you close the dishwasher
door.
If you have soft water, you may not need rinse aid for it may
cause awhite filmto develop on your dishes.
A measured amount of rinse aid is released during the final rinse.As with detergent, the amount
of rinse aid needed for your dishes depends on the hardness of the water in your area. Too much
rinse aid can result in lather offoaming and cause cloudiness or steaks on your dishes. If the
water in your area is very soft, you maynot need rinse aid. If you do,you can dilute the rinse aid
with an equal amount of water.
The rinse aid dispenser has six settings. Always start with the dispenser set on " 1 ". If spots and
poor drying are problems, increase the amount of rinse aid dispensed byremoving the dispenser
lid and rotating the dial to "2". If the dishes still are not drying properly or are spotted, adjust the
dial to the next higher number until your dishes are spot-free. We suggest you to set on "4" .
If only four settings we suggest you set on "2".
5
Page 8
If there is no rinse aid warning light in the control panel, you can judge the amountof rinse aid by thefollowing means. The
black dot on the rinse aid dispenser indicates the amount of rinse aid inthe dispenser.As the rinse aid diminishes, the size of
the black dot decreases. You should never let the rinse aid get below 1 / 4 full.
Astherinseaiddiminishes,the size of the black dot on therinse
aid level indicator changes, asillustrated below.
Full
3/4full
1/2full
1 /4 full - Should refill to eliminate spotting
Empty
The upper rack is designed to hold more delicate and lighter dishware such as glasses,coffee and tea cup and saucers, as well
as plates, small bowls and shallow pans(as long as they are not too dirty).
Position thedishes and cookware so that they do not get moved by the spray of water.
The upper rack can be adjusted for height by puttingwheels of different height intotherails.
Cups
2
1
1
2
Small serving bowl
Large servingbowl
6
3
5
3
4
5
6
Glasses
Saucers
Dish
4
We recommendthat you place large items whichare most difficult to clean into the lower rack: pots, pans, lids,
serving dishes and bowls, as shownin the figureto the right.
It is preferable to place serving dishes and lids on the side of the racks in order toavoid blocking the rotation of the
top spray arm.
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.
2
2
5
1
3
4
1
Oval platter
Dessert dishes
2
Soup plates
3
Dinner pla tes
4
Silverware basket
5
6
Page 9
Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets,the spoon should
be loaded individually into the appropriate slots, Especially long utensils should be placed in the horizontal position at the
front of the upper rack.
5
3
1
4
5
1
4
5
4
3
4
4
6
8
4
4
4
3
1
5
1
3
5
1
1
1
5
3
5
1
3
5
2
2
3
3
2
2
2
2
2
2
7
7
Teaspoons
1
Dessert spoons
2
Soup spoons
3
Forks
4
Knife
5
Serving fork
6
Serving spoon
7
8
Gravy ladle
Do not let any item extend throughbottom.
Program indicator light
Make sure that the plug 0f the appliance is inserted into thewall socket.
1
Make sure that the water supply is turned on to full pressure.
2
3
Load the dishwasher(see the section entitled, " Loading the Dishwasher " ).
4
Pour in the detergent(se e the section entitled, " Salt, Detergent and RinseAid").
Open thedoor,press the ON/OFF button,and the ON/OFF light will turn on.
5
Press the "prog key-press" to select the "Wash cycle".(see the section entitled."Wash Cycle Table".)
6
7
Close the door,the washing will start after ten second.
Press the key to set the start time.This dishwasher can be delayed to start for 1 to 24 hours,and the
8
display window beside the delay key can indicate the remaining time.If you want to cancel the delay start,
just press the key to make the remaining time become 0.
Premise
have already been released, and the appliancemay have already drained the wash water. If this is the case, the detergent dispenser
must be refilled (seethe paragraph entitled "LoadingtheDetergent " ).
Open the door,Press the "Prog key-press" more than threesecond,then you can change the program to the desired cycle setting
(see the sectionentitled, " Startinga wash cycle. . . " ).Then, close the door.
When the washing cycle has finished,the buzzer of dishwasher will mooing eight second,then stop.Turn off the appliance using the
ON/OFF button,open the door of the dishwa sher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes
and utensils while theyare still hot and more susceptible to breakage. Theywillalsodrybetter.
: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may
dely
Program key-press
Delay key-press
A forgotten dish can be added any time before the detergent cup opens.
Open the door a little to stop the washing.
1
After the spray arms stop working,you can open the door
2
completely.
It is dangerous to open the door when washing,because the hot water may be scaldedtoyou.
3
Add forgotten dishes.
4
Close the door, the dishwasher will work after ten second.
7
Page 10
The filter prevent larger remnants of food or other objects from getting inside the pump. This residue can
occasionally clog up the filters.
The filter system consists of a filter cylinder(Coarse filter),
A flat (Main filter) and a microfilter(fine filter).
1
2
3
2
1
3
Reconnect the water inlet to the
4
water valve.
Main filter
Food and soil particles trapped by this filter are pulverized by a
special jet on the lower spray arm and washed down the
drain.
Coarse filter
Larger items, such as pieces of bone or glass, that could clog
the drain are trapped in the coarse filter. To remove an item
caught in this filter, gently squeeze the taps on the top of this
filter and lift it out.
Fine filter
This filter holds soil and food residue in the sump area and
prevents it from being redeposit on the dishes during a cycle.
If your dishwasher is left in an unheated place during the winter, ask a service technician to:
1
Cut off electrical power to the dishwasher. Remove
fuses or trip circuit breaker.
pipe
2
Turn off the water supply and disconnect the water
inlet pipe from the water valve.
Drain water from the inlet and water valve.pipe
Uncrew
It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings. To remove the
spray arm, screwoff the nut to take out the washeron top of the spray arm and remove the arm. Wash the arms in soapy and warm
water and use a soft brush to clean the jets. Replace them after rinsing them thoroughly.
3
(Use a pan to catch the water.)
Filter assembly
For best performance and results, the filter assembly must be cleaned.
The filter efficientlyremoves foodparticlesfrom thewash water, allowing it tobe
recirculated during the cycle. For this reason, it is a good idea to remove the larger
food particles trapped inthe filter after each wash cycle by rinsing thesemicircular
filter and cup under running water. To remove the filter assembly, pull on the cup
handle in the upward direction. The entire filter assembly should be cleaned at least
once a month.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble
the filter parts as shown in the figures left and reinsert the entire assembly in the
dishwasher, positioning in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the
filter may reduce the performance level of the appliance and damage dishes andutensils.
Remove the plastic sump cover in the
5
tub the bottom and use a sponge to
soak up water in rubber boot.
Never run the dishwasher without the filters in place.
8
Page 11
To clean the edge around the door, you should use only a soft warm, damp rag. Toprevent
To clean the edge around the door, you should use onlya soft warm, damp rag. Toprevent
penetration of water into the door lock and electrical components, do not use a spray cleaner
penetration of water into the door lock and electrical components, do not use a spray cleaner
of any kind.
of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
scratch the finish. Some papers towels can also scratchor leave marks on thesurface.
WQP8-9325
WQP8-9325
P
P
Never use a spray cleaner to clean the door panel for it could damage the door lock and electrical components. It is not allowed
Never use a spray cleaner to clean the door panel for it could damage the door lock and electrical components. It is not allowed
to use the abrasive agent or some paper towel becauseof the risk of scratching or leaving spots on the stainless steel surface.
to use the abrasive agent or some paper towel becauseof the risk of scratching or leavingspots on the stainless steel surface.
88
88
scratch the finish. Some papers towels can also scratchor leave marks on thesurface.
Something will occasionally move into the filters and the drain pump. If this occurs, the drain
Something will occasionally move into the filters and the drain pump. If this occurs, the drain
pumpsemployed in your dishwashers are designedto automatically reverse, ejecting the
pumpsemployed in your dishwashers are designedto automatically reverse, ejecting the
item back into the sump area or down the drain.If you have toremove an obstacle from the
item back into the sump area or down the drain.If you have toremove an obstacle from the
drain pump,before you remove the filters, you should turn off the power; Then removethe
drain pump,before you remove the filters, you should turn off the power; Then removethe
small black insert from the sumparea. (You might want to remove any standingwater first).
small black insert from the sumparea. (You might want to remove any standingwater first).
Scoop out the item that is probably in the sump area and causes the obstruction. Rem ember
Scoop out the item that is probably in the sump area and causes the obstruction. Rem ember
to replace the black insert before you put the filters back in.
to replace the black insert before you put the filters back in.
After every wash, turn off the water supply to the
After every wash, turn off the water supply to the
applianceand leave the doorslightly ajar so that
applianceand leave the doorslightly ajar so that
moistureand odors are not trapped inside.
moistureand odors are not trapped inside.
Before cleaning or performing maintenance, always
Before cleaning or performing maintenance, always
remove the plug from the socket. Do not run risks.
remove the plug from the socket. Do not run risks.
To clean the exterior and rubber parts of the dishwasher,
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
do not use solvents or abrasive cleaning products.
Rather, use only a cloth and warm soapy water.
Rather, use only a cloth and warm soapy water.
Toremovespotsorstainsfromthesurfaceofthe
Toremovespotsorstainsfromthesurfaceofthe
interior, use acloth dampened with waterand a little
interior, use acloth dampened with waterand a little
white vinegar, or a cleaning product made specifically
white vinegar, or a cleaning product made specifically
for dishwashers.
for dishwashers.
Fused electrical supply is required-copper wire only.Time delay fuse or circuit breaker recommended and provide separate
Fused electrical supply is required-copper wire only.Time delay fuse or circuit breaker recommended and provide separate
circuit servingonly thisappliance.Outlet should be placed in adjacent cabinet.
circuit servingonly thisappliance.Outlet should be placed in adjacent cabinet.
Make sure that the plug on the appliance remains accessible after installation.
Make sure that the plug on the appliance remains accessible after installation.
When you go on holiday, it is recommened that you run a
When you go on holiday, it is recommened that you run a
wash cycle with the dishwasher empty and then remove
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
leave the door of the appliance slightly ajar. This will help
the sealslast longerand preventodors from forming
the sealslast longerand preventodors from forming
within the appliance.
within the appliance.
If the appliance mustbemoved, try to keep it in thevertical
If the appliance mustbemoved, try to keep it in thevertical
position.If absolutely necessary, it can be positioned on
position.If absolutely necessary, it can be positioned on
its back.
its back.
Oneof the factors that causeodors to form in the
Oneof the factors that causeodors to form in the
dishwasherisfood that remainstrappedin the seals.
dishwasherisfood that remainstrappedin the seals.
Periodic cleaning with a damp spongewill prevent this
Periodic cleaning with a damp spongewill prevent this
from occurring.
from occurring.
After making sure that the voltage and the frequency values for the current in the home correspond to those
After making sure that the voltage and the frequency values for the current in the home correspond to those
on therating plate and that the electrical system is sizedtor the maximum voltage on the rating plate, insert
on therating plate and that the electrical system is sizedtor the maximum voltage on the rating plate, insert
the pluginto an electrical socket which is earthed properly. If the electrical socket to which the appliance
the pluginto an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate tor the plug, replace the socket, installed byqualified electrician,rather
must be connected is not appropriate tor the plug, replace the socket, installed byqualified electrician,rather
then usingan adaptors.
then usingan adaptors.
9
9
Page 12
The appliancemust be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below theminimum
consult our Service Department for advice.
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
1
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
2
Turn water fully on before starting the dishwasher.
3
The safety supply hose consists ofthe double walls. The hose'ssystem guarantees its intervention by blocking the flow of water
in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated hose is full
of water.
A hose that attaches to a sink spray can burst if it is installed on the same water lineas the dishwasher. If your sink has one, it is
recommended thet the hose bedisconnected and the hole plugged.
Turn off the water.
1
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
2
room, from severe splashing.
Unscrew The safety supply hose from the faucet..
3
Remove the power cord plug from the wall receptacle.
1
Disconnect Unicouple from faucet adapter.
2
Connect the cold water supply hose to a threaded 3/4(inch) connector and make surethatit is fastened tightlyin place.
If the water pipes are new or have not been used for an extended periodof time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and
damage theappliance.
The water supply to the appliance can also be connected to the house hot water line (centralizedsystem, heating system),
as long as it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes
and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for the connection to the
cold water line.
10
Page 13
'
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Water pressure is low
Overflow
'
Some audible sounds are
normal
Utensils are not secure
in the baskets or something
small has dropped into
the basket
Motor hums Dishwasher has not been used regularly. If you do not use it
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Check that the water supply is connected properly and
the water is turned on.
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
Sound from soft food shredding action and detergent cup
opening.
To ensure everything is secured in the dishwasher.
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 4 litres of cold water to the tub. Close and latch the
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
Spilled rinse agent Always wipe up rinse agent
spills immediately.
Detergent with
colorant was used
Rinse agent dispenser
is empty
Improper program
Improper rack loading Make sure that the action of the detergent dispenser and
Extremely hard water
Low inlet
temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent
dispenser
Incorrect dosage of
detergent
Make sure that the detergent is the one without colorant.
Make sure that the rinse agent dispense is filled.
Sel ect st ronger pr ogram
spray arms are not blocked by large dishware.
To remove spots from glassware:
Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
11
Page 14
Combination of soft
water and too much
detergent
Tea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water
Use less detergent if you have soft water and select a
shortest cycle to wash the glassware and to get them clean.
to remove the stains by hand.
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
Iron deposits in water
can cause an overall film
Hard water minerals To clean the interior, use a damp sponge with dishwasher
Dial is not in the
'
position
Dishes block detergent
cups
Normal phenomenon
Aluminum utensils have
rubbed against dishes
This is normal A small amount of clean water around the outlet on
Overfill dispenser or rinse
aid spills
OFF
You have to call a water softener company for a special filter.
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Turn the Dial to
OFF position and slide the door latch to the
left.
Re-loading the dishes properly.
There is some steam coming through the vent by the door
latch during drying and water draining.
Use a mild abrasive cleaner to eliminate those marks.
the tub bottom at the back of the tub keeps the water
seal lubricated.
Be careful not to overfill the rinse aid dispenser.
Spilled rinse aid could cause oversudsing and lead
to overflowing. Wipe away any spills with a damp cloth.
Dishwasher isn t level
'
Make sure the dishwasher is level.
12
Loading...