Camus Hydronics DMH-261, DMH-291, DMH-391, DMH-501, DMH-601 Installation, Operation And Service Manual

...

Download

6226 Netherhart Road, Mississauga, Ontario, L5T 1B7

99-0212

Rev. 00

INSTALLATION OPERATION

AND SERVICE MANUAL

GAS FIRED WALL HUNG & FLOOR MOUNT RESIDENTIAL

COMMERCIAL STAINLESS STEEL BOILERS

DynaMax HS SERIES

HYDRONIC HEATING

Models; DMH081, 101, 151, 201, 251, 211, 261, 291, 391, 501, 601, 701, 801

HOT WATER SUPPLY

Models; DMW082 ,102, 152, 202, 252, 212, 262, 292, 392, 502, 602, 702, 802

COMBINATION HEATING/HOT WATER SUPPLY

Models; DMC083, 103, 153, 203, 253,

213, 263, 293, 393, 503, 603, 703, 803

HLW

WARNING:

If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death

Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

o Do not try to light any appliance, o Do not touch any electrical switch; do not

use any phone in your building,

o Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s instructions,

o If you cannot reach your gas supplier, call

the fire department.

Qualified installer, service agency or the gas supplier must perform installation and service.

To the

nstaller:

After installa

tion, these instructions

must be given to the end user or left on or near the appliance. To the End User: This booklet contains important information about this appliance. Retain for future

reference.

CAMUS HYDRONICS LTD.

Contents

PART 1 GENERAL INFORMATION ............................................................................................................... 1

1.1 INTRODUCTION .............................................................................................................................. 1

1.2 SPECIAL INSTRUCTIONS TO OWNER .............................................................................................. 1

1.3 CHECKING EQUIPMENT.................................................................................................................. 1

1.4 DISPLAY UNIT ................................................................................................................................. 1

1.5 SEQUENCE OF OPERATION ............................................................................................................ 1

1.5.1 Heat Transfer Process.................................................................................................................... 1

1.5.2 End of Sequence ............................................................................................................................ 2

1.6 INSTALLATION CODES .................................................................................................................... 2

1.7 WARRANTY..................................................................................................................................... 2

1.8 REMOVAL OF EXISTING APPLIANCE ............................................................................................... 3

1.9 BOILER/FURNACE ROOM OPERATING CONDITION ....................................................................... 3

1.10 LOCATION OF UNIT ........................................................................................................................ 3

1.11 CLEARANCE FROM COMBUSTIBLE MATERIAL ............................................................................... 4

PART 2 AIR INLET AND VENTING ............................................................................................................... 8

2.1 GENERAL VENTING GUIDE ............................................................................................................. 8

2.2 CATEGORY IV VENTING .................................................................................................................. 8

2.2.1 Approved Venting Materials Category IV ...................................................................................... 8

2.3 CATEGORY II VENTING ................................................................................................................... 9

2.3.1 Approved Venting Materials Category II ....................................................................................... 9

2.4 COMBINED COMBUSTION AIR INLET ............................................................................................. 9

2.5 VENT TERMINATION AND AIR INLET CLEARANCES ...................................................................... 10

2.5.1 Sidewall Venting .......................................................................................................................... 10

2.5.2 Sidewall Air Inlet .......................................................................................................................... 10

2.5.3 Sidewall Concentric Vent/Air ...................................................................................................... 11

2.6 Vertical Direct Venting ................................................................................................................. 11

PART 3 GAS CONNECTION ....................................................................................................................... 13

3.1 GAS CONNECTION ....................................................................................................................... 13

3.2 GAS PIPING ................................................................................................................................... 13

3.3 INSTALL PIPING ........................................................................................................................... 13

3.4 CHECKING GAS SUPPLY PRESSURE............................................................................................... 13

3.5 HIGH and LOW GAS PRESSURE SWITCHES (Optional) ................................................................. 14

3.6 AIR/GAS RATIO VALVE ................................................................................................................. 14

3.7 BURNER ........................................................................................................................................ 14

PART 4 WATER CONNECTION .................................................................................................................. 15

4.1 FREEZE PROTECTION OUTDOOR INSTALLATION ......................................................................... 15

4.2 WARNING REGARDING CHILLED WATER SYSTEMS ..................................................................... 16

4.3 INLET AND OUTLET CONNECTIONS ............................................................................................. 16

4.4 MINIMUM PIPE SIZE REQUIREMENTS ......................................................................................... 16

4.5 HEAT EXCHANGER ........................................................................................................................ 16

4.6 LOW WATER TEMPERATURE SYSTEMS ........................................................................................ 16

4.7 PIPING ARRANGEMENTS .............................................................................................................. 16

4.7.1 Field Supplied Components ......................................................................................................... 16

4.8 FLOW PROVING DEVICE (wall mount models and combination models only) ........................... 18

4.9 WATER FLOW SWITCH (Floor mount hydronic and DHW models only) ..................................... 18

4.10 LOW WATER CUTOFF (If Equipped) ............................................................................................. 18

4.11 RELIEF VALVE................................................................................................................................ 18

4.12 DHW TUNING VALVE (combination models only) ....................................................................... 18

PART 5 ELECTRICAL & CONTROLS ............................................................................................................ 19

5.1 ELECTRICAL CONECTIONS ............................................................................................................ 19

5.2 HIGH LIMIT ................................................................................................................................... 19

5.3 DYNAMAX HS CONTROLLER ......................................................................................................... 19

5.3.1 SERVICE PARTS ............................................................................................................................ 19

5.3.2 IGNITION MODULE LOCKOUT FUNCTIONS ................................................................................. 20

5.4 ERROR TABLE ............................................................................................................................... 20

5.4.1 Manual Reset Codes .................................................................................................................... 20

5.4.2 Automatic Reset Codes ............................................................................................................... 20

PART 6 CONTROL PANEL .......................................................................................................................... 21

6.1 DYNAMAX HS CONTROLLER ......................................................................................................... 21

6.2 SETTING THE DYNAMAX HS CONTROLLER ................................................................................... 21

PART 7 COMPONENTS ............................................................................................................................. 39

7.1 DIRECT SPARK IGNITER ................................................................................................................ 39

7.2 FLAME SENSOR ............................................................................................................................ 39

7.3 COMBUSTION AIR FAN................................................................................................................. 39

7.4 GAS VALVE ................................................................................................................................... 39

7.5 OUTER JACKET .............................................................................................................................. 39

PART 8 TROUBLESHOOTING .................................................................................................................... 40

8.1 SETTING THE CORRECT COMBUSTION ........................................................................................ 49

8.2 GAS VALVE ADJUSTMENT PROCEDURE ....................................................................................... 49

PART 9 MAINTENANCE ............................................................................................................................ 51

9.1 EXAMINE THE VENTING SYSTEM ................................................................................................. 51

9.2 VISUALLY CHECK MAIN BURNER FLAMES .................................................................................... 51

9.3 CLEANING BOILER HEAT EXCHANGER ......................................................................................... 51

9.4 CONDENSATE TREATMENT .......................................................................................................... 52

9.5 IGNITER AND FLAME SENSOR ELECTRODES ................................................................................ 52

9.6 CHECK IGNITER GROUND WIRING ............................................................................................... 52

9.7 BURNER MAINTENANCE .............................................................................................................. 52

9.7.1 Burner Removal and Cleaning ..................................................................................................... 53

9.8 REMOVAL OF COMBUSTION CHAMBER LINING .......................................................................... 53

9.9 COMBUSTION AND VENTILATION AIR ......................................................................................... 53

9.10 GAS VALVE VOLTAGE ................................................................................................................... 54

9.11 COMBUSTIBLE MATERIALS .......................................................................................................... 54

9.12 FREEZE PROTECTION FOR INDOOR & OUTDOOR INSTALLATIONS .............................................. 54

9.13 FREEZE PROTECTION FOR A HEATING BOILER SYSTEM (Optional) ............................................. 54

PART 10 INSTALLATIONS ............................................................................................................................ 55

10.1 CHECKING THE INSTALLATION ..................................................................................................... 55

10.2 CHECKING THE CONSTRUCTION .................................................................................................. 55

10.3 HEATING BOILER INSTALLATIONS ................................................................................................ 55

10.4 INSPECT & RECHARGE CONDENSATE COLLECTION/NEUTRALIZING RESERVOIR ........................ 55

10.5 WATER CONNECTIONS ................................................................................................................. 55

10.6 PIPING LENGTHS .......................................................................................................................... 55

10.7 SUMMARY .................................................................................................................................... 56

10.8 DOMESTIC HOT WATER WITH STORAGE TANK ........................................................................... 56

10.9 DOMESTIC HOT WATER WITH PLATE HEAT EXCHANGER ............................................................ 56

10.10 TEMPERATURE RISE AT FULL FIRING RATE .................................................................................. 57

10.11 LEAD LAG SETUP .......................................................................................................................... 58

10.12 LOCAL/REMOTE SWITCH.............................................................................................................. 59

10.13 MODBUS/LOCAL SWITCH............................................................................................................. 59

10.14 APPLIANCE ................................................................................................................................... 59

PART 13 PIPING DIAGRAMS ....................................................................................................................... 60

PART 14 EXPLODED VIEW & PARTS LIST .................................................................................................... 65

PART 15 ELECTRICAL DIAGRAMS ............................................................................................................... 73

15.1 DM 80- 299 INTERNAL WIRING DIAGRAM .................................................................................. 73

15.2 DM 399 – 800 INTERNAL WIRING DIAGRAM ............................................................................... 74

15.2 FIELD WIRING ............................................................................................................................... 76

15.2.1 System Sensor ............................................................................................................................. 76

15.2.2 Lead Lag Setup ............................................................................................................................. 76

PART 1 GENERAL

INFORMATION

1.1 INTRODUCTION

The DynaMax HS boiler is a fan assisted boiler based on a push through design which offers several venting options. Heat output is controlled by a one to one air/gas ratio control gas valve which provides seamless modulation. The boiler provides central heating, domestic hot water or combination heating with DHW priority at working pressure up to 160 PSI. It is designed for use with a fully pumped and pressurized water system. The boiler/water heater will automatically modulate to provide heat outputs from 100% down to approximately 20% of rated input.

The DynaMax HS utilizes a negative pressure gas valve. The operation of the fan will generate a negative pressure in the venturi, which draws in a matching amount of gas through the valve.

During operation the DynaMax HS maintains steady state efficiency across the entire range of modulation. Air and gas are metered in precise proportion (1:1 Ratio) allowing combustion characteristics which determine efficiency to remain the same over the entire operating range.

The DynaMax HS is designed so that all of the sensible heating value and most of the latent heat is being transferred to the water.

1.2 SPECIAL INSTRUCTIONS TO OWNER

This manual supplies information for the installation, operation and servicing of the appliance. It is strongly recommended that this manual be reviewed completely before proceeding with an installation

CAUTION

It is important that all gas appliances are installed by a qualified installer/technician. It is in your own interest and that of safety to ensure that all local codes, and all the following “NOTES” and “WARNINGS” are complied with. Installing, servicing or adjusting this appliance should be performed only by a qualified installer/technician that is trained by Camus Hydronics. The serviceman must utilize a combustion analyzer with CO2, CO, and draft gauge, to set the appliance according to Camus Hydronics’

recommendation

prior to commission

ing.

NOTE

RETAIN

THIS MANUAL FOR FUTURE REFERENCE

1.3 CHECKING EQUIPMENT

Check for signs of shipping damage upon receiving equipment. Pay particular attention to parts accompanying the boiler, which may show signs of being hit or otherwise being mishandled. Verify total number of pieces shown on packing slip with those actually received. In case there is damage or a shortage, immediately notify carrier.

1.4 DISPLAY UNIT

The display unit will indicate status and will display selected temperature. Refer to Part 6 Control Panel, which provides details to modes and error codes displayed on the appliance.

1.5 SEQUENCE OF OPERATION

1) Power switch is placed in the “ON” position.

2) Minimum 120 VAC 60Hz single phase (15A circuit) is supplied to the DynaMax HS field connection board.

3) 24Vac power is supplied to the DynaMax HS Controller which provides all setup and ignition control functions.

4) After the appliance water pump starts, flow is proven by the flow proving device or flow switch. The normally open dry contacts in the low water cutoff (LWCO), if supplied, is to be wired in series with the normally open contacts of the flow proving device.

5) Locate the probe type LWCO in the piping at least some distance above the boiler/ inlet connection. In all cases check with local codes.

6) Depending on the selected mode, the appliance operates as a master or slave configuration.

7) The DynaMax HS controller initiates a startup sequence once it receives a heat demand.

8) The DynaMax HS controller energizes the on-board pump and starts to ramp up the voltage to the electrically commutated DC motor of the combustion fan.

9) The fan will run at pre-purge speed until the pre-purge timer is satisfied. Once this is complete the DynaMax HS controller provides a signal to ignition fan speed.

10) The DynaMax HS controller goes through internal safety checks and if this is satisfied the ignition sequence begins.

11) The DynaMax HS controller supplies voltage to the air/gas ratio control valve. The air/gas ratio control valve senses the pressure across the venturi and supplies gas to pre-mix with air.

12) The igniter will spark for 4 seconds, with the gas valve opened, and the fan running at ignition speed.

13) Spark igniter lights the air/gas mixture. The DynaMax HS controller looks for a minimum flame rectification signal of 0.8Vdc from the flame sensor. If the signal is present the DynaMax HS Controller will allow the gas valve to remain open. The burner is now firing at starting input rate.

14) Boiler will modulate to the correct fan speed to meet heat demand. The modulation rate is controlled via pulse width modulation (PWM) signal.

15) Fan speed will slowly decrease as heat request nears the heat demand. If heat demand is sustained for a long duration of time the boiler will get to a point of steady-state and the fan will rotate at constant speed.

16) When the heat demand is satisfied or is removed the burner will shut off and the fan speed will ramp up to the preset post-purge speed until the post-purge timer is satisfied.

17) The boiler will then go into standby as it waits for the next heat demand.

1.5.1 Heat Transfer Process

1) Burner input continues to increase until inlet water temperature reaches the setpoint temperature.

2) Burner input may stabilize at a fixed rate where demand equals input.

3) Burner input will decrease rate when outlet water temperature approaches temperature Setpoint.

1.5.2 End of Sequence

1) Setpoint temperature is satisfied.

2) Power to the gas valve is turned off.

3) Combustion air fan ramps to a stop over the factory preprogrammed time period.

4) Thermostat is now in standby mode waiting for the next “Call for Heat”.

WARNING

To minimize the possibility of serious personal injury, fire or damage to your appliance, never violate the following safety rules.

DO NOT

Do not use this appliance if any part of it has been

under

water. The possible damage to a flooded appliance can be

extensive and present numerous safety hazards. Any appliance that has been under water must be replaced

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance. • Do not touch any electric switch: do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department.

IMPORTANT

Consult and follow local Building and Fire Regulations and other Safety Codes that apply to this installation. Contact the local gas utility company to inspect and authorize all gas and flue connections.

Installation

and service must be per

formed by a

qualified technician/installer, and trained by Camus Hydronics.

WARNING

Should overheating occur or the gas supply fails to shut off, DO NOT turn off or disconnect the electrical supply to the pump. Shut off the gas supply at a location external to the appliance.

• Boilers and water heaters are heat producing appliances. To avoid damage or injury, do not store materials against the appliance or the vent-air inlet system. Use proper care to avoid unnecessary contact (especially children) with the appliance and vent-air inlet components.

• Never cover appliance, lean anything against it, store trash or debris near it, stand on it or in any way block the flow of fresh air to appliance.

• UNDER NO CIRCUMSTANCES may flammable materials such as gasoline or paint thinner be used or stored in the vicinity of this appliance, vent-air inlet system or any location from which fumes could reach the appliance or vent-air inlet system.

• A gas appliance that draws combustion air from the equipment room where it is installed must have a supply of fresh air circulating around it during burner operation for proper gas combustion and proper venting.

1.6 INSTALLATION CODES

The equipment shall be installed in accordance with those installation regulations enforced in the local area where the installation is to be made. These shall be

carefully followed in all cases. Authorities having jurisdiction shall be consulted before installations are made. In the absence of such requirements, the installation shall conform to the latest edition or current as amended of the National Fuel Gas Code, ANSI Z223.1 and/or CAN/CGAB149 Installation Code. All electrical wiring must be done in accordance with the requirements of the authority having jurisdiction or, in the absence of such requirements, with national electrical code, ANSI/NFPA70 and/or the Canadian electrical code part 1 CSA C22.1. Where required by the authority having jurisdiction, the installation must conform to American Society of Mechanical Engineers Safety Code for Controls and Safety Devices for Automatically Fired Boilers, ASME CSD-1. All boilers must conform to the latest edition of the ASME Boiler and Pressure Vessel Code, Section II. Where required by the authority having jurisdiction, the installation must comply with the CSA International, CAN/CGA-B149 and/or local codes. This appliance meets the safe lighting performance criteria with the gas manifold and control assembly provided, as specified in the ANSI standards for gas-fired units, ANSI Z21.13.

1.7 WARRANTY

• Factory warranty (shipped with unit) does not apply to units improperly installed or improperly operated.

• Factory warranty shall apply only when the appliance is installed in accordance with local plumbing and building codes, ordinances and regulations, the printed instructions provided with it and good industry practices.

• Excessive water hardness causing a lime build-

up in the stainless steel coils or tubes is not a fault of the appliance and is not covered by warranty. Consult the factory for recommendations for use in hard water areas. (See Water Treatment and

Water Chemistry)

• Using or storing corrosive chemicals in the

vicinity of this appliance can rapidly attack the stainless steel venting and heat exchanger coils and voids warranty.

• Damage caused by freezing or dry firing voids

warranty.

• This appliance is not to be used for temporary

heating of buildings under construction.

• The manufacturer shall NOT be held liable for any

personal injury or property damage due to ice formation or the dislodging of ice from the vent system or the vent termination

1.8 REMOVAL OF EXISTING APPLIANCE

When an existing appliance is removed from a common venting system, the common venting system is likely to be too large for proper venting of the appliances remaining connected to it. At the time of removal of an existing appliance, the following steps must be followed with each appliance remaining connected to the common venting system placed in operation, while the other appliances remaining connected to the common venting system are not in operation.

• Seal any unused openings in the common venting system.

• Visually inspect the venting system for proper size and horizontal pitch and determine that there is no blockage, restriction, leakage, corrosion or other deficiency, which could cause an unsafe condition.

• Insofar as is practical, close all building doors and windows and all doors between the spaces in which the appliances remaining connected to the common venting system are located and other spaces of the building. If applicable turn on the clothes dryers and any appliances not connected to the common venting system. Turn on any exhaust fans, such as range hoods and bathroom exhausts, so they will operate at maximum speed. Do not operate a summer exhaust fan. Close fireplace dampers.

• Place in operation the appliance being inspected. Follow the lighting instructions. Adjust thermostat so that appliance operates continuously.

• Test for spillage at the draft control device relief opening after 5 minutes of main burner operation. Use a cold mirror, the flame of a match, or a candle or smoke from a cigarette.

• After it has been determined that each appliance remaining connected to the common venting system properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace dampers and any other gas-burning appliance to their previous condition of use.

• Any improper operation of the common venting system should be corrected so that the installation conforms to the National Fuel Gas Code, ANSI Z223.1 and/or CAN/CGA B149, Installation Codes. When resizing any portion of the common venting system, the common venting system should be resized to approach the minimum size as determined using the appropriate tables in Part 11 of the National Fuel Gas Code, ANSI Z223.1 and /or CAN/CGA B149, Installation Codes.

Heat exchanger surfaces and vent piping should be checked every six months for deterioration and carbon deposits. Remove all soot or other obstructions from the chimney and flue, which might impede draft action. Replace any damaged or deteriorated parts of the venting system.

A qualified service technician should follow this procedure when inspecting and cleaning the heat exchanger and vent pipe.

1) Turn off electrical power and main manual gas shut-off

and allow appliance to cool down.

2) Remove the vent pipe at connection to heat exchanger

and check heat exchanger and vent for obstruction and clean as necessary.

3) Remove burner from appliance and carefully clean as required. Never brush or wipe the knitted metal fiber surface. Use a garden hose or gently wash under the tap. Vacuum out any deposits found in the heat exchanger.

CAUTION

Never use a pressure washer or compressed air to clean

the burner.

4) Reinstall parts removed in steps 2 and 3. Be sure that vent pipe has proper pitch and is properly sealed. Replace any damaged gasket or refractory. Tighten fan flange mounting nuts to 3 ft-lb.

5) Restore electrical power and gas supply to appliance.

6) Place appliance in operation using lighting instructions provided.

7) Confirm proper operation of all safety devices

8) Check for gas leaks and proper vent operation.

NOTE

Experience has shown that improper installation or

system design, rather than faulty equipment, is the cause

of most operating problems

1.9 BOILER/FURNACE ROOM OPERATING

CONDITION

• Due to low jacket losses from the appliance, temperatures in the vicinity of the boiler room may drop significantly; supplemental heat is required to maintain ambient temperature at acceptable levels.

1.10 LOCATION OF UNIT

Install this appliance in a clean, dry location with adequate service clearance.

• Do not locate this appliance in an area where it will be

subject to freezing unless precautions are taken. Radiant losses from the heater is minimal and should not be relied on to keep the appliance room warm.

• Do not locate this appliance where it may be exposed

to a corrosive atmosphere

• The appliance should be located close to a floor drain

in an area where leakage from the appliance or connections will not result in damage to the adjacent area or to lower floors in the structure, it is

recommended that a suitable drain pan, adequately drained, be installed under the unit. Under no circumstances is the manufacturer to be held responsible for water damage in connection with this unit, or any of its components.

• If the appliance is installed above the level of the

building’s radiation system, a low water cut-off device must be installed in the appliance outlet some distance above the heat exchanger inlet/outlet connections. Some local codes require the installation of a low water cut-off on all systems

• When placing the appliance be aware that a minimum

clearance of 24” must be provided at the front to allow easy access to the heat exchanger. DynaMax HS wall mount units do not require access through the sides and can be placed adjacent to each other with zero clearance. Floor mount units require access on the left side as you face the front.

• The appliance must be installed so that the ignition system components are protected from water (dripping, spraying, etc.) during appliance operation and service (circulator replacement, control replacement, etc.)

• Appliances located in a residential garage and in

adjacent spaces that open to the garage and are not part of the living space of a dwelling unit must be installed so that all burners and burner ignition devices have a minimum clearance of not less than 18" (46cm) above the floor. The appliance must be located or protected so that it is not subject to physical damage by a moving vehicle.

• DO NOT install this appliance in any location where

gasoline or flammable vapors are likely to be present.

• Appliance must be installed on a level floor. Maintain

required clearances from combustible surfaces.

• The appliance designed for indoor installation (Indoor Models) must be installed indoors where it is protected from exposure to wind, rain and weather.

• The appliance designed for outdoor installation (Outdoor Models) must be installed outdoors. Always consider the use of a shelter such as a garden shed in lieu of direct exposure of the appliance to the elements. The additional protection afforded by the shelter will help to minimize nuisance problems with electrical connections and will allow easier servicing of the appliance under severe weather conditions.

1.11 CLEARANCE FROM COMBUSTIBLE

MATERIAL

This appliance is suitable for alcove (a closet without a door) installation with minimum clearances to combustibles as follows:

Table 1: Clearance from Combustibles

Clearances from Combustibles

Wall Hung

Model

Floor Mount

Model

TOP: 0”

SIDES: 0”

REAR: 0”

12"

VENT (Vent Adapter): 1”

VENT (PVC/CPVC): 0”

FRONT: 3”

6”

Figure 1: Wall Hung Clearance from Combustibles

Figure 2: Floor Mount Clearance from Combustibles

NOTE

Clearances from combustible construction are noted on the appliance rating plate

1” From

outer edge

of adapter

PVC/CPVC/PPE Vent Pipe

Single Wall Vent Adapter

Table 2: DynaMax HS Wall Hung Service Clearances

Model

Service Clearance, Inches (cm)

Front Top Right Side Left Side Rear

24” (61cm) 3” (8 cm) 4” (10 cm) 4” (10 cm) 0” (0 cm)

100

24” (61cm) 3” (8 cm) 4” (10 cm) 4” (10 cm) 0” (0 cm)

150

24” (61cm) 3” (8 cm) 4” (10 cm) 4” (10 cm) 0” (0 cm)

200

24” (61cm) 3” (8 cm) 4” (10 cm) 4” (10 cm) 0” (0 cm)

250

24” (61cm) 3” (8 cm) 4” (10 cm) 4” (10 cm) 0” (0 cm)

Figure 3: DynaMax HS Wall Hung Model Dimensions

Table 3: Appliance Dimensions and Specifications

Model

Depth Dim.

"A" [in.]

Dim.

"B" [in.]

Equivalent

Length of Vent & Air

Intake Pipes at Recommended

Diameter, [in.]

Water

Connection

at Boiler [in.] NPT

Gas Connection

at Boiler [in.] NPT

Over 25'

and up to

100'

Over 15'

and up to

25'

Up to 15'

16 1/2 12 3 3 2 1 1/2

100

16 1/2 12 3 3 2 1 1/2

150

16 1/2 12 3 3 2 1 1/2

200

23 1/2 19 3 3 2 1 1/2

250

23 1/2 19 3 3 2 1 1/4 1/2

Maintain minimum specified clearances for adequate operation. All installations must allow sufficient space for servicing the vent connections, water pipe connections, circulating pump, bypass piping and other auxiliary equipment, as well as the appliance

Table 4: DynaMax HS Floor Mount Service Clearances

Model

Service Clearance, Inches (cm)

Front Top Right Side Left Side Rear

210

12” (31cm) 24” (61cm) 0” (0cm) 12” (31cm) 14” (36 cm)

260

12” (31cm) 24” (61cm) 0” (0cm) 12” (31cm) 14” (36 cm)

299

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36cm)

399

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36 cm)

500

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36 cm)

600

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36cm)

700

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36 cm)

800

12” (31cm) 24” (61cm) 0” (0cm) 12” (31 cm) 14” (36 cm)

Figure 4: DynaMax HS Floor Mount Model Dimensions

Table 5: Appliance Dimensions and Specifications

Model

Dim.

"A" [in.]

Dim.

"B"

[in.]

Dim.

"C" [in.]

Dim.

"D" [in.]

Dim.

"E"

[in.]

Dim.

"F"

[in.]

Dim.

"J"

[in.]

Equivalent Length of Vent & Air Intake

Pipes at Recommended Diameter, [in.]

Water

Conn.

Heater

[in.]

NPT

Gas

Conn.

Boiler

[in.] NPT

Category IV

CAT.II

Comb.

Vents

Over 25'

and up

to 100'

Over 15'

and up

to 25'

Up to

15'

210

36 22 3/4 14 1/4 23 24 1/4 34 1/4 32 3 3 2 4 1 1/2

260

36 22 3/4 14 1/4 23 24 1/4 34 1/4 32 3 3 2 4 1 1/4 1/2

299

47 1/8 34 7/8 14 23 29 7/8 33 7/8 32 4 3 3 5 1 1/4 3/4

399

47 1/8 34 7/8 14 23 29 7/8 33 7/8 32 4 3 3 5 1 1/2 1

500

47 1/8 34 7/8 14 23 29 7/8 33 7/8 32 4 3 3 6 1 1/2 1

600

47 1/8 36 1/4 14 23 30 3/4 38 40 1/2 4 3 3 6 2 1

700

47 1/8 36 1/4 14 23 30 3/4 38 40 1/2

4 (Air), 6

(Vent)

4 4 7 2 1

800

47 1/8 36 1/4 14 23 30 3/4 38 40 1/2

5 (Air), 6

(Vent)

5 5 7 2 1

Figure 5: DynaMax HS Wall Hung Service Clearances

Figure 6: DynaMax HS Floor Mount Service Clearances

PART 2 AIR INLET AND VENTING

It is extremely important to follow these venting instructions carefully. Failure to do so can cause severe personal injury, death or substantial property damage.

2.1 GENERAL VENTING GUIDE

The DynaMax HS Wall Hung is a category IV condensing appliance, 97% efficient unit. The DynaMax HS Floor Mount is a category II condensing appliance, 97% efficient.

• The DynaMax HS may be vented with:

manufactured prefabricated UL/ ULC listed vents of AL29-4C or 316L stainless steel or with plastic vent certified to UL/ ULC S636, such as, IPEX System 636 CPVC or IPEX System 636 PVC or as permitted by local jurisdictions.

• The DynaMax HS boiler must be vented and

supplied with combustion and ventilation air as described in this section. Ensure that the venting and combustion air supply complies with these instructions.

• Installations must be in accordance with Part 7,

“Venting of Equipment”, of the latest edition of the National Fuel Gas Code, ANSI Z223.1 for US installations or the latest edition of CAN/CGA Standard B149 Installation Code for Gas Burning Appliances and Equipment in Canada.

• The distance of the vent terminal from adjacent

buildings, windows that open and building openings MUST comply with the latest edition of the National Fuel Gas Code, ANSI Z223.1 for U.S. installations or CAN/CGA Standard B149 Installation Code for Canadian Installations.

• Vent connection is made directly to the flue outlet

opening on top of the unit for the wall mount unit and at the back of the unit for floor mount. The connection from the appliance vent to the stack must be made as direct as possible. The first 3 feet of vent from the appliance flue outlet must be readily accessible for visual inspection.

• Vent connectors serving appliances vented by

natural draft shall not be connected into any portion of a mechanical draft system operating under positive pressure.

• A UL listed concentric vent/air intake kit may be

used with the DynaMax HS.

• Horizontal runs of vent pipe shall be securely

supported (approximately every 4 feet) to prevent sagging and maintain a minimum upward slope of ¼” per foot from the appliance to the vent terminal.

• The weight of the venting system must not rest on

the unit. Adequate support of the venting system must be provided in compliance with local codes and other applicable codes.

• All connections should be secured and sealed per

the vent manufacturer’s specifications. When a positive vent system is disconnected for any reason, the flue must be reassembled and resealed according to the vent manufacturer’s instructions.

• Do not use an existing chimney as a raceway if

another appliance or fireplace is vented through the chimney.

• Inspect completed vent and air supply piping thoroughly to ensure all connections are sealed and are in compliance with the instructions provided and satisfy requirements of all applicable codes.

NOTE

All vent pipes must be properly assembled and supported, and the exhaust must be pitched a minimum of 1/4 inch per foot back to the boiler. All components used to fabricate and assemble the vent system are to originate from the same supplier.

Equivalent length of fittings depend on centre line radius of the fitting. Consult published tables or the vent supplier for accurate equivalent lengths.

Example: 30 feet of CPVC pipe + (3 x 5 feet) 90o elbows + (1 x 3 feet) 45o elbow = 48 equivalent feet of piping for centerline radius of 1.5D, where D is the pipe diameter.

2.2 CATEGORY IV VENTING

A category IV appliance is individually vented through a dedicated vent.

The DynaMax HS Wall Hung boilers/ water heaters shall only be vented as a Category IV appliance.

Both Wall Hung and Floor Mount appliances shall be vented using sealed positive vent suitable for a condensing appliance with the following venting options:

1) Sidewall or rooftop termination where both the vent and combustion air inlet air are in the same zone. The inlet and vent terminals are to be installed with a minimum 12” separation distance between centerline of inlet and centerline of exhaust. Refer to Fig. 8, 9, and 10 for sidewall termination and Fig. 11 for rooftop termination.

2) Sidewall termination with vent and combustion air inlet from separate zones.

3) Single Pipe thru wall or rooftop venting with combustion air inlet from the boiler room.

NOTE

Vent Option 3 not recommended for R-2000 homes or equivalent air tight construction.

2.2.1 Approved Venting Materials Category IV

1) PVC and CPVC (Chlorinated Polyvinyl Chloride) Schedule 40 approved to ULC S636.

2) Manufactured prefabricated UL/ULC listed vent of AL294C or 316L stainless steel. Use of 316L is limited to use in applications where there is no possibility of contaminants in the air such as refrigerants, chlorine etc.

3) PVC-DWV approved to comply with ANSI/ASTM D2665 (US Jurisdictions ONLY when permitted)

4) PVC Schedule 40 approved to comply with ANSI/ASTM D1785. (US Jurisdictions ONLY when permitted)

5) CPVC Schedule 40 approved to comply with ANSI/ASTM F441. (US Jurisdictions ONLY when permitted)

6) Polypropylene approved to comply with ULC S636

Table 6: Maximum Flue Temperature for Various Vent Materials

Vent Material Maximum Flue Temperature [oF]

PVC

149

CPVC

194

PPE

230

AL29-4C

300+, limited only by rating of seals

316L Stainless Steel

300+, limited only by rating of seals

Stack temperature is typically between 15-30oF above inlet water temperature depending on model size and firing rate.

Air Inlet (Supply Air or Fresh Air) Piping

• PVC

• CPVC (Chlorinated Polyvinyl Chloride)

• PPE (Polypropylene)

• ABS (Acrylonitrile-Butadiene-Styrene)

• Single wall, Galvanized

• Single wall, Stainless steel

• Single wall, Aluminium

Single wall air inlet pipes are to be insulated 5 feet from the wall toward the interior of the building to minimize external sweating.

The following air intake options shall be utilized:

• Outside air sealed direct (vertical or horizontal)

• Outside air ducted to jacket flange

• Indoor Air

NOTE

For wall hung units that are installed outdoors the bottom of the unit must be at least 36” above ground or 12” above normal snow levels.

NOTE

Sealed combustion is required when DynaMax HS is placed in a space with other fan-assisted appliances.

Table 7: Required Vent and Air Inlet Diameters

Equivalent Length of Vent & Air Intake Pipes

at Recommended Diameter*

Model

Category IV

Category

Over 25' and up

to 100'

Over 15'

and up

to 25'

15'

3" 3" 2" -

100

3" 3" 2" -

150

3" 3" 2" -

200

3" 3" 2" -

210

3" 3" 2" 4”

250

3" 3" 2" -

260

3" 3" 2" 4”

299

4" 3" 3" 5”

399

4" 3" 3" 5”

500

4" 3" 3" 6”

600

4” 3” 3” 6”

700

4” (Air), 5” (Vent) 4” 4” 7”

800

5” (Air), 6” (Vent) 5” 5” 7”

* Consult factory for recommendations applicable to venting combinations not shown above.

2.3 CATEGORY II VENTING

A category II appliance may be combined into a common negative pressure venting system designed to ASHRAE requirements using a proven vent sizing program. Vent designs are to be certified by a qualified professional designer acceptable to the authority having jurisdiction.

1) The DynaMax HS Floor Mount boiler may be vented as a Category II appliance using sealed vent suitable for a condensing appliance.

2.3.1 Approved Venting Materials Category II

1) PVC and CPVC Schedule 40 approved to ULC S636.

2) Manufactured prefabricated UL/ULC listed vent of AL29-

4C or 316L stainless steel. Use of 316L is limited to use where there is no possibility of contaminants in the air such as refrigerants, chlorine etc.

3) PVC-DWV approved to comply with ANSI/ASTM D2665

(US Jurisdictions ONLY when permitted).

4) PVC Schedule 40 approved to comply with ANSI/ASTM

D1785. (US Jurisdictions ONLY when permitted)

5) CPVC Schedule 40 approved to comply with

ANSI/ASTM F441. (US Jurisdictions ONLY when permitted).

6) Polypropylene approved to comply with ULC S636

Air Inlet (Supply Air or Fresh Air) Piping

• PVC

• CPVC (Chlorinated Polyvinyl Chloride)

• ABS (Acrylonitrile-Butadiene-Styrene)

• PPE (Polypropylene)

• Single wall, Galvanized

• Single wall, Stainless steel

• Single wall, Aluminium

Single wall air inlet pipes are to be insulated 5 feet from the wall toward the interior of the building to minimize external sweating.

The following air intake options shall be utilized:

• Outside air sealed direct (vertical or horizontal)

• Outside air ducted to jacket flange

• Indoor Air

NOTE

Sealed combustion is required when DynaMax HS is placed in a space with other fan-assisted appliances.

2.4 COMBINED COMBUSTION AIR INLET

To avoid the possibility of nuisance lockouts in cold climates install DynaMax HS appliances may be installed with a combined combustion air inlet.

The combined combustion air inlet pipe sizing can be calculated using the method shown below:

Equivalent pipe diameter = Sq Root [(d1)2 + (d2)2 + (d3)2 + … + (dn)2], where dn = individual pipe diameter

• Example: Find the equivalent pipe diameter of three air inlet pipes, 3” (7.6cm), 3” (7.6cm) and 4” (10.2cm) Equivalent pipe diameter = Sq Root[(3)2 + (3)2 + (4)2] = Sq Root(34) = 5.8”, select 6” (15.3cm) equivalent diameter pipe.

Air inlet point for multiple boiler air inlets must be provided with an exterior opening which has a free area equal to or greater than the total area of all air inlet pipes connected to the common air inlet. This exterior opening for combustion air must connect directly to the outdoors. The total length of the combined air inlet pipe must not exceed a maximum of 100 equivalent feet (30.5m). Compensate for the restriction in an area provided by any screens, grills or louvers installed in the common air inlet point. Screens, grills or louvers installed in the common air inlet can reduce the free area of the opening from 25 to 75% based on the materials used. Increase the inlet accordingly.

2.5 VENT TERMINATION AND AIR INLET CLEARANCES

2.5.1 Sidewall Venting

• The first 3 feet (1m) of vent from the appliance flue outlet must be readily accessible for inspection.

Figure 7: Vertical Orientation

* Always check local codes for minimum distance above

ground or snow levels

Figure 8: Horizontal Configuration

* Always check local codes for minimum distance above

ground (or snow levels in cold climates)

Location of Vent Termination

1) Total length of vent piping must not exceed limits stated in Table 7.

2) Bottom of vent terminal shall be located at least 3 feet (0.90m) above grade or above normal snow levels. In all cases the appliance shall be installed in accordance with local codes

3) DynaMax HS can vent up to 100 equivalent feet. Elbows can range from 3 to 5 feet in equivalent length depending on the centerline radius.

4) Vent outlet shall terminate at least 12” (0.30m) away from any forced air inlet. Vent must be at least 7 feet (2.15m) above grade when located adjacent to public walkways due to normal formation of water vapour in the combustion process.

5) Vent outlet MUST NOT terminate below a forced air inlet at any distance.

6) Vent cannot terminate below grade. Position vent termination where vapours will not damage walls or plants or may be otherwise objectionable.

7) Vent terminal shall not be installed closer than 3 feet (1m) from an inside corner of an L-shaped structure, window well, stairwell, alcove, courtyard or other recessed area as wind eddies could affect boiler performance or cause recirculation.

8) DO NOT terminate closer than 4 feet (1.25m) horizontally and vertically from any electric meter, gas meter, regulator, relief valve, or other equipment. In all cases local codes take precedence

9) Position terminations so they are not likely to be damaged by foreign objects, or exposed to a buildup of debris.

10) Vent piping must terminate in an elbow pointed outward or away from air inlet.

11) Flue gas condensate can freeze on exterior walls or on the vent cap. Frozen condensate on the vent cap can result in a blocked flue condition. Keep the vent cap/terminal clear of snow, ice, leaves, debris etc. Some discolouration to exterior building surfaces is to be expected. Adjacent brick or masonry surfaces should be protected with a rust resistant sheet metal plate.

12) Perform regularly scheduled inspections to ensure vent terminal is unobstructed.

2.5.2 Sidewall Air Inlet

Figure 9: Sidewall Vent and Air Inlet Configuration

* Always check local codes for minimum distance above

ground or snow levels

Location of a Sidewall Air Inlet Cap

1) Total length of piping for air inlet must not exceed the limits stated in Table 7.

2) Point of termination for the sidewall air inlet cap must be located a minimum of 12 inches (0.30m) away from the flue gas termination, but never above.

3) Air piping must terminate in a down-turned elbow to avoid recirculation of flue products into the inlet air stream.

4) DO NOT terminate closer than 4 feet (1.25m) horizontally and vertically from any electric meter, gas meter, regulator, relief valve, or other equipment. In all cases local codes take precedence

5) DO NOT terminate the air inlet in a window well, stairwell, alcove, courtyard or other recessed area as wind eddies could affect performance or cause recirculation.

6) Air inlet cannot terminate below grade.

7) Locate terminations so they are not likely to be damaged by foreign objects, or exposed to build-up of debris.

8) Perform regularly scheduled inspections to ensure that the air inlet terminal is unobstructed.

2.5.3 Sidewall Concentric Vent/Air

A concentric vent kit can be used with the DynaMax HS appliance. Both combustion air and vent pipes must terminate outside the structure.

1) Total length for venting or air must not exceed the limits stated in Table 7.

2) Bottom of the termination shall be located at least 3 feet (0.90m) above grade or above normal snow levels. In all cases the appliance shall be installed in accordance with local codes

3) Termination MUST NOT terminate below a forced air inlet at any distance

4) Termination cannot terminate below grade. Position the termination where vapours will not damage walls or plants or may be otherwise objectionable.

5) The termination shall not be installed closer than 3 feet (1m) from an inside corner of an L-shaped structure, window well, stairwell, alcove, courtyard or other recessed area as wind eddies could affect boiler performance or cause recirculation.

6) DO NOT terminate closer than 4 feet (1.25m) horizontally and vertically from any electric meter, gas meter, regulator, relief valve, or other equipment. In all cases local codes take precedence

7) Position termination so they are not likely to be damaged by foreign objects, or exposed to a build-up of debris.

8) Flue gas condensate can freeze on exterior walls or on the vent cap. Frozen condensate on the vent cap can result in a blocked flue condition. Keep the vent cap/terminal clear of snow, ice, leaves, debris etc. Some discolouration to exterior building surfaces is to be expected. Adjacent brick or masonry surfaces should be protected with a rust resistant sheet metal plate.

9) Perform regularly scheduled inspections to ensure that the termination is unobstructed.

10) Operate the appliance for one heat cycle to ensure combustion air and vent pipes are properly connected to the concentric vent termination connections.

CAUTION

Do not operate appliance with the terminal cap removed as this may result in the recirculation of flue products.

Figure 10: Concentric Sidewall Termination

Figure 11: Concentric Vent Sidewall

Termination and Fittings

The air inlet opening must be at least 12 inches (0.30m) away from (never above) the vent termination and at least 3 feet (1m) above grade or 1 foot (0.30m) above normal maximum snow levels.

2.6 Vertical Direct Venting

Location of Vent Termination

1) Total length of piping for venting must not exceed limits stated in Table 7.

2) Vent piping must terminate in a 45o elbow if plastic piping is used or in an approved vent cap if using metal venting. Vent outlet must be at least 1 foot away and 1 foot above from the air inlet opening which must terminate in a double elbow facing downwards.

3) Vertical termination must be a minimum of 3 feet (1m) above the point of exit or 1 foot (0.30m) above normal snow levels.

4) Vertical termination less than 10 feet (3.05m) from a parapet wall must be a minimum of 2 feet (0.61m) higher than the parapet wall.

5) DO NOT terminate closer than 4 feet (1.25m) horizontally and vertically from any electric meter, gas meter, regulator, relief valve, or other equipment. In all cases local codes take precedence.

6) Position the air inlet and vent terminations so they are not likely to be damaged by foreign objects, or exposed to build-up of debris.

7) Perform regularly scheduled inspections to ensure that the vent terminal is unobstructed.

8) Termination MUST NOT terminate below a forced air inlet at any distance

Location of a Vertical Air Inlet Opening

1) The total length of piping for inlet air must not exceed the limits given in Table 7.

2) The air inlet consists of two 90o elbows installed at the point of termination for the vertical air inlet pipe. A 90o elbow and a 90o street elbow may be used to make this assembly. If a straight piece of pipe is used between the two elbows, it should not exceed 6” (0.15m) in length. The air inlet opening must be at least 1 foot below the vent opening. The air piping must be no further than 2 feet (0.6m) from the center of the vent pipe. This arrangement avoids exhaust gases from re-circulating into the inlet air stream. Refer to Figure 12.

3) Air inlet must terminate at least 3 feet (1.0m) above the roof or 1 foot (0.3m) above normal snow levels and at least 1 foot (0.3m) below the vent termination.

4) Locate terminations so they are not likely to be damaged by foreign objects or exposed to build-up of debris.

5) Perform regularly scheduled inspections to ensure that the air inlet terminal is unobstructed.

Figure 12: Vertical Direct Venting Configuration

6) Operate the appliance for one heat cycle to ensure combustion air and vent pipes are properly connected to the concentric vent termination connections.

Figure 13: Concentric Vent Vertical Venting

CAUTION

Do not operate appliance with the terminal cap removed as this may result in the recirculation of flue products. Water may also flow into the combustion air pipe and into the burner enclosure.

Length of Air Inlet Pipe

The maximum total length of the vertical roof top combustion air inlet pipe as installed from the appliance to the terminal cap must not exceed 100 equivalent feet (30.5m) in length.

IN GENERAL

• The operation of exhaust fans, compressors, air handling units etc. can rob air from the room, creating a negative pressure condition leading to reversal of the natural draft action of the venting system. Under these circumstances an engineered air supply is necessary.

• If the appliance is to be installed near a corrosive or potentially corrosive air supply, the appliance must be isolated from it and outside air supplied as per code.

• Potentially corrosive atmospheres will result from exposure to permanent wave solution, chlorinated waxes and cleaners, chlorine, water softening chemicals, carbon tetrachloride, halogen based refrigerants, Freon cleaning solvents, hydrochloric acid, cements and glues, masonry washing materials, antistatic fabric softeners, dry cleaning solvents, degreasing liquids, printing inks, paint removers, etc.

• The equipment room MUST be provided with properly sized openings to assure adequate combustion air and proper ventilation when the unit is installed with a proper venting system.

PART 3 GAS CONNECTION

Verify that the appliance is supplied with the type of gas specified on the rating plate. Consult factory for installations at high altitude.

3.1 GAS CONNECTION

• Safe operation of unit requires properly sized gas supply piping. See gas line sizing data.

• Gas pipe size may be larger than appliance connection.

• Installation of a union at the appliance gas line

connection is required for ease of service and removal of the gas train.

• Install a manual main gas shutoff valve, outside of the appliance as required by local codes.

• A trap (drip leg) MUST be provided in the inlet gas connection to the appliance.

• Optional gas controls may require routing of bleeds and vents to the atmosphere, outside the building when required by local codes.

Table 8: Recommended Gas Pipe Size

Single Appliance Installation

(For distance from natural gas meter or propane second

stage regulator)

Input 0-100 FT 101-200 FT 201-300 FT

Btu/Hr

x1000

NAT. L.P. NAT. L.P. NAT. L.P.

¾” ½” ¾” ½” 1” ¾”

100

¾” ½” 1” ¾“ 1” ¾”

150

1” ¾” 1 ¼” 1“ 1 ¼” 1”

200

1” ¾” 1 ¼” 1” 1 ¼” 1”

250

1 ¼” 1” 1 ¼” 1” 1 ½” 1 ¼”

299

1 ¼“ 1“ 1 ½” 1 ¼“ 1 ½“ 1 ¼“

399

1 ¼“ 1“ 1 ½“ 1 ¼“ 2“ 1 ½“

500

1 ½“ 1 ¼“ 2“ 1 ½“ 2“ 1 ½“

600

1 ½“ 1 ¼“ 2“ 1 ½“ 2“ 1 ½“

700

2 “ 1 ½“ 3“ 2 ½“ 3“ 2 ½ “

800

2 “ 1 ½“ 3“ 2 ½“ 3“ 2 ½ “

3.2 GAS PIPING

All gas connections must be made with pipe joint compound resistant to the action of liquefied petroleum and natural gas. All piping must comply with local codes and ordinances.

3.3 INSTALL PIPING

• The gas line must be sufficient to handle the total installed capacity. Verify pipe size with your gas supplier.

• Use approved piping as per code.

• Install a manual main gas shutoff valve at the appliance

gas inlet, outside of the appliance and before the gas valve.

• Run pipe to the Appliance gas inlet.

• Install a sediment trap in the supply line to the Appliance

gas inlet.

• Apply a moderate amount of good quality pipe compound.

• For LP gas, consult your LP gas supplier for expert installation.

The appliance and its individual gas shut-off valve must be disconnected from the supply piping when pressure testing the gas supply piping at pressures above ½ PSI

Table 9: Gas Pressures at Inlet to Appliance

PROPANE NATURAL GAS

Minimum (inches W.C.)

11 3

Maximum (inches W.C.)

11 14

The gas supply line must be of adequate size to prevent undue pressure drop and must never be smaller than the size of the connection on the appliance. Sizing based on Table 8 is recommended, depending on model. Before operating the appliance, the complete gas train and all connections must be tested using soap solution.

Verify that the appliance is supplied with the type of gas specified on the rating plate. Heating values of local natural gas are to be between 950 and 1010 Btu/ft3. Consult factory if heating values are outside this range or if a gas with a mixture of constituents is being used.

3.4 CHECKING GAS SUPPLY PRESSURE

• Turn main power switch to “OFF” position.

• Shut off gas supply at the manual gas cock in the gas

piping to the appliance. If fuel supply is LP gas, shut off gas supply at the tank.

• DM80 – 399: Loosen the slotted screw from the gas pressure test port on the gas valve. Connect manometer or magnahelic gauge to test port. Range of scale should be 0 to 14 inch W.C. or greater to check inlet pressure.

• DM500 – 800: Remove the 1/8" hex plug from the gas pressure test port located upstream of gas valve. Install a pressure tapping suitable to connect to a manometer or magnahelic gauge. Range of scale should be 0 to 14 inch W.C. or greater to check inlet pressure.

• Turn on gas supply at field installed manual gas cock; turn on LP gas at tank if required.

• Turn power switch to “ON” position.

• Initialize call for heat.

• Observe the gas supply pressure as the burner fires at

100% of rated input. Supply pressure is to remain stable.

• Ensure inlet pressure is within specified range as specified in Table 9.

• If gas pressure is out of range, contact the gas utility, gas supplier, qualified installer or service agency to determine necessary steps to provide proper gas pressure to the control.

• If gas supply pressure is within normal range, proceed to remove gas manometer and tighten slotted screw on gas valve (DM80 – 399) or replace pressure tap fittings in the gas piping to the appliance (DM500 – 800). Turn power switch to “OFF” position.

• Turn on gas supply at the manual valve; turn on LP gas at tank if required.

• Turn power switch to “ON” position.

• Adjust set point to the desired water temperature.

• Check appliance performance by cycling the system

while you observe burner response. The burner should ignite promptly. Flame profile should be stable, see section 11.2, Visually Check Main Burner Flames. Turn system off and allow burner to cool, then cycle burner again to ensure proper ignition and flame characteristics.

IMPORTANT

Upon completion of initial installation or following any repair work on the gas system, leak test all gas connections with a soap solution while the main burner is firing. Immediately repair any leak found in the gas train or related components. DO NOT operate an appliance with a leak in the gas train, valves or related gas piping.

3.5 HIGH and LOW GAS PRESSURE SWITCHES (Optional)

Figure 14: Low gas pressure switch (cover removed)

High and low gas pressure switches are available as an option and are wired in series with the normally closed blocked flue switch. The high gas pressure switch is used to monitor the gas pressure at the outlet of the control valve. If gas pressure exceeds the maximum setting of the pressure switch, the appliance will shut down and an ILK OFF message will be indicated on the display. The low gas pressure switch is to monitor the minimum incoming gas supply pressure supplied to the gas train. If gas pressure falls below the minimum setting of the pressure switch, the appliance will shut down and an ILK OFF message will be displayed.

3.6 AIR/GAS RATIO VALVE

The main gas valve supplying gas to the burner on this appliance utilizes a servo pressure regulator providing a slow opening, fast closing safety shut off and air/gas ratio control for the gas combustion process. The valve is a 1:1 negative pressure gas valve. The valve performs the functions of a pressure regulator, safety shutoff, and air/gas ratio control. Full closing of the valve seat occurs in less than

0.8 seconds when the valve is de-energized. Operation of

the gas valve in combination with the combustion air fan allows the burner input rate to vary from 20% to 100% based on temperature demand. The inlet gas supply pressure must be maintained within the specified minimum and maximum pressures as indicated in Table 9.

The air/gas ratio is preset at the factory and adjustment is not usually required if gas supply pressure is maintained within the specified range. There are no serviceable parts on the air/gas ratio valve control.

Figure 15: DynaMax HS 80 – 250, 260 1:1 Air/Gas Ratio

Control Valve

Figure 16: DynaMax HS 299 – 399 1:1 Air/Gas Ratio

Control Valve

Figure 17: DynaMax HS 500 – 800 1:1 Air/Gas Ratio

Control Valve

3.7 BURNER

Figure 18: DynaMax HS Burner

Low-fire air/gas ratio adjustment, use slotted screwdriver for adjustment, clockwise increases CO2

High fire adjustment:

use throttle screw

locate

d on venturi

Low fire adjustment screw Torx

40 clockwise increases CO

Gas Inlet

Low-fire air gas ratio adjustment (use Torx 40 for adjustment clockwise increases CO2)

High-fire air gas ratio adjustment (Use

slotted screwdriver for adjustment, counter-clockwise increases CO2)

Lift top cover to access high fire

air/gas ratio adjustment (use 3mm allen key for adjustment, counterclockwise increases CO

Gas Inlet

This appliance uses a single cylindrical burner installed horizontally into the cavity located in the center of the heat exchanger. A unique burner is used for each one of the DynaMax HS models.

Burners may NOT be interchanged between different Btu/hr input models. The burner consists of a round mounting flange welded to a ported stainless steel mixing tube. This stainless steel tube is covered with a close fitting, knitted stainless steel metal fiber alloy material that forms the burner outer surface. The burner is setup to operate in blue mode and infrared operating condition should be avoided. Infrared operation will occur only if air to gas adjustments is incorrect. If infrared operation is noted the cause must be corrected.

The burner should be removed for inspection and cleaning on an annual basis. An appliance installed in a dust or dirt contaminated environment will require inspection and cleaning on a more frequent schedule. The fan assisted combustion process may force airborne dust and dirt contaminants, contained in the combustion air, into the burner. With sustained operation, non-combustible contaminants may reduce burner surface area, reduce burner input or cause non-warrantable damage to the burner.

Airborne contaminants such as dust, dirt, concrete dust or dry wall dust can be drawn into the burner with the combustion air and block the burner surface area. DO NOT operate this appliance during construction.

The spark igniter and flame sensor are removable from the combustion chamber mounting door without removing the burner assembly.

Never use an open flame (match, lighter, etc.) to check gas connections.

Regulated Gas Supply Pressures for DynaMax HS Boilers & Water Heaters

A stable gas supply pressure is important to avoid rough starts with machines like the DynaMax HS which use a 1 to 1 ratio control valve for internal gas pressure regulation. Camus requires that all DynaMax HS models be supplied with no more than 14” w.c. supply pressure. This means that lockup pressure must not exceed 14” w.c.

A suitable lockup regulator with internal or external relief will not exceed running pressure by more than 20%.

When required a final stage gas regulator is to be located as close as possible but no more than 10 feet from the appliance.

It is paramount that maximum lockup pressure be confirmed before any attempt is made to start up the appliance.

Operating the DynaMax HS at lockup pressures exceeding 14” w.c. could lead to delayed ignitions and damage to the appliance.

PART 4 WATER CONNECTION

• Check all applicable local heating, plumbing and building safety codes before proceeding.

• If the appliance is installed above radiation level it must be provided with a low water cut-off device at the time of appliance installation (available from Camus). Some local codes require the installation of a low water cut-off on all systems.

• Before connecting DynaMax HS to piping in a closed loop system, flush system thoroughly and refill with clean water and add chemical treatment to bring into balance.

• Follow the chemical suppliers instructions. A regular maintenance schedule will ensure that acceptable water quality is maintained, typically a Langlier/ Reznor index will provide this information.

• Strainers are recommended to be installed into the system to prevent foreign objects from entering the heat exchanger.

• A pressure relief valve is supplied with each DynaMax HS. The relief valve must be mounted in a vertical position and piped to the floor in a manner acceptable to the enforcing authority.

• Be sure to provide unions and gate valves at inlet and outlet to the appliance so that it can be easily isolated for service.

• On combination heaters a flow setter valve at the appliance outlet facilitates setting of the desired outlet temperature at high fire. Refer to Section 10.9 Domestic Hot Water with Plate Heat Exchanger for more details

• This appliance is a low mass stainless steel tube design which provides for instant heat transfer. All appliances are supplied with an internal suitable specific pump mounted in place. When replacing the pump, replace with one of equal or better-performance.

• An air vent is supplied on the heat exchanger header to eliminate trapped air. Install venting devices at high points in the system as well to eliminate trapped air in the piping.

• Use suitable pipe hangers or floor stands to support the weight of all water and gas piping.

• The DynaMax HS must be installed so that the gas ignition system components are protected from water (dripping, spraying, rain, etc.) during appliance operation and service (circulator replacement, control replacement, etc.)

4.1 FREEZE PROTECTION OUTDOOR

INSTALLATION

• Appliance installations are not recommended outdoors or in areas where danger of freezing exists unless precautions are taken. Maintaining a mixture of 70% water and 30% propylene glycol is the preferred method of freeze protection in hydronic systems. DO NOT exceed a mixture of 50/50. This mixture will protect the appliance to approximately -35ºF (-37ºC). Follow the chemical suppliers directions.

• For outdoor installations a snow screen should be installed to prevent snow and ice accumulation around the appliance. Regular inspections should be made to ensure that air inlet and vent are free of snow and ice. Always consider the use of a shelter such as a garden shed in lieu of direct exposure of the appliance to the elements. The additional protection afforded by the

shelter will help to minimize nuisance problems with electrical connections and will allow easier servicing of the appliance under severe weather conditions.

4.2 WARNING REGARDING CHILLED WATER SYSTEMS

When an appliance is connected to an air conditioning system where the same water is used for heating and cooling, the chiller must be piped in parallel with the appliance. Appropriate isolation valves; manual or motorized must be provided to prevent the chilled water from entering the appliance.

Figure 19: Chilled Water System

4.3 INLET AND OUTLET CONNECTIONS

• All water connections must meet American National

Standard Pipe Threads (NPT).

• For ease of service, install unions on inlet and outlet of

the appliance. The connection to the appliance marked “Inlet” on the header should be used for return from the system. The connection on the header marked “Outlet” is to be connected to the supply side of the system.

4.4 MINIMUM PIPE SIZE REQUIREMENTS

Minimum water pipe connections are as follows for DynaMax HS single unit installations. The equivalent number of straight feet of pipe for each valve and fitting in the connecting piping must be considered to properly arrive at the total equivalent feet of straight pipe in the field installed piping to the appliance. Consult factory if longer piping distances are required for a specific application. It is recommended to use copper piping for all system piping to reduce the possibility of the formation of deposits, which may result in heat exchanger starvation.

System pipe size must be in accordance with Table 10, and between supply and return lines, must not exceed 50 feet of equivalent length. Connection sizes at the heater are given in Tables 3 & 5. Any reduction in recommended pipe size may decrease flow resulting in high temperature rise across the heat exchanger, boiler noise, flashing to steam and nonwarrantable heat exchanger damage.

Table 10: Minimal System Pipe Size

Input

[BTU/hr]

Water Size, NPT

[in.]

80,000 1 100,000 1 150,000 1 199,000 1 1/4 250,000 1 1/4 299,000 1 1/2 399,000 2 500,000 2 600,000 2 700,000 2 800,000 2

4.5 HEAT EXCHANGER

This appliance uses precision formed stainless steel tubing to maximize the heat transfer process and to achieve 97% steady-state efficiency. The DynaMax HS is designed to withstand 160 PSIG working pressure. A factory installed circulating pump ensures proper water flow during burner operation and creates enough velocity inside the stainless steel tubes and headers that prevents scaling. Installing a strainer upstream of the heat exchanger will reduce the likelihood of tubes from being blocked by debris.

4.6 LOW WATER TEMPERATURE SYSTEMS

In applications where the heating system requires supply water temperatures below 110°F, connections may be made directly to the DynaMax HS. At incoming temperatures of 80oF or lower the DynaMax HS achieves maximum efficiency. Inlet temperatures must not drop below 40oF to prevent freezing.

4.7 PIPING ARRANGEMENTS

4.7.1 Field Supplied Components

1) Boiler system piping Boiler system piping MUST be sized according to Table 10. Reducing the pipe size can restrict the flow rate through the boiler, causing boiler damage and will void the manufacturer’s warranty.

2) Isolation Valves Use only full port ball valves. Failure to supply full port ball valves may result in reduced flow rate through the boiler, causing boiler damage and will void the manufacturer’s warranty.

3) Anti-Scald Mixing Valve An anti-scaled mixing valve is recommended when DHW storage is above 120oF.

4) Unions Recommended for ease of serviceability.

5) System Temperature Sensor A system temperature sensor is to be installed in the main header at a point to detect controlled temperature and where it will not lead to shortcycling of the boiler.

An instantaneous water heater is designed to deliver hot water without the use of a storage tank. It is suitable for applications with variable load such as restaurants,

condominiums, apartments and motels and typically used in conjunction with tempering valves to achieve temperature control.

Table 11: Flow and Pressure Drop at a Given

Temperature Rise (Hydronic Heating)

Input,

Btu/Hr

30 °F (16.7 °C) 35 °F (19.4 °C)

Temp Rise Temp Rise

USGPM

(min.

flow)

∆∆∆∆P Ft.

USGPM.

(min. flow)

∆∆∆∆P Ft.

5.0 8.2 4.3 6.2

100,000

6.3 12.3 5.4 9.4

150,000

9.5 10.4 8.1 7.8

199,000

12.6 7.2 10.8 5.8

250,000

15.8 11.5 13.5 8.7

299,000

18.9 9.3 16.2 7.0

399,000

25.2 8.4 21.6 6.3

500,000

31.5 9.2 27.0 6.9

600,000

38.8 17.5 32.0 11.8

700,000

45.3 18.2 40.0

14.4

800,000

51.8 23.5 43.0 16.0

Table 12: Flow and Pressure Drop at a Given

Temperature Rise (DHW)

Input,

Btu/Hr

20 °F (11.1 °C)

Temp Rise

USGPM

(min. flow)

∆∆∆∆P Ft.

80,000

7.5 11.5

100,000

9.4 26.9

150,000

14.0 27.8

199,000

19.2 25.9

250,000

23.5 28.3

299,000

28.8 25.8

399,000

38.4 23.9

500,000

48.6 29.4

600,000

57.6 34.2

700,000

70.4 40.0

800,000

77.6 43.2

DynaMax HS Floor Mount Piping Diagrams

4.8 FLOW PROVING DEVICE (wall mount models and combination models only)

Figure 20: Flow Proving Device

The flow proving device is designed to detect when flow is present. This is done by detecting the amount of current (amperes) that exists in the neutral wire from the pump. When the current becomes too low a ILK error is displayed indicating a lack of water inside the boiler. The flow proving device is provided on all DynaMax HS wall mount models (DM 80 – 250) and combination floor model units (213 –

803). This switch is factory wired.

Table 13: Flow Proving Device Indicator LED’s

LED Illuminated Symptom

Left Normal operation

Right Current under trip point

When testing the operation of the flow proving device always ensure that 115Vac is being supplied to the pump.

4.9 WATER FLOW SWITCH (Floor mount hydronic and DHW models only)

A paddle style water flow switch is shipped loose and is to be installed in the outlet piping on all floor model heating boilers (DM 211-801) and hot water supply heaters (DM 212 – 802). The flow switch is to be installed in a horizontal run of pipe in order to provide effective contact. The flow switch is to be wired into the DynaMax HS terminal board labelled ‘Flow Switch’.

4.10 LOW WATER CUTOFF (If Equipped)

If this boiler is installed above radiation level, a low water cut-off device must be installed at the time of boiler installation. Some local codes require the installation of a low water cut-off on all systems. Electronic low water cut-offs are available as a factory supplied option on all models. Low water cut-offs should be tested every six months. The normally open switch contact of the low water cutoff is to be wired in series with the flow switch. This can be wired into the DynaMax HS terminal labelled ‘Flow Switch’.

CAUTION

Remove jumper when connecting to 24 VAC circuit.

Figure 21: Low Water Cut Off Electrical Connections (Watts)

Figure 22: Low Water Cut Off Electrical Connections (ITT)

4.11 RELIEF VALVE

Figure 23: Relief Valve

This appliance is supplied with a relief valve sized in accordance with ASME Boiler and Pressure Vessel Code, Section IV (“Heating Boilers”). If this component is shipped loose, no valve is to be placed between the relief valve, and the appliance. To prevent water damage, the discharge from the relief valve shall be piped to a suitable floor drain for disposal when relief occurs. No reducing couplings or other restrictions shall be installed in the discharge line. The discharge line shall allow complete drainage of the valve and line. Relief valves should be manually operated at least once a year.

CAUTION

Avoid contact with hot discharge water

4.12 DHW TUNING VALVE (combination models only)

A DHW tuning valve is provided with all DynaMax HS combination models. In cases where flow control is not possible by the end user the DHW tuning valve is designed to act as a maximum flow controller. The tuning valve is designed to provide the correct amount of hot water for each particular DynaMax HS model and application. Refer to section 10.9 Domestic Hot Water with Plate Heat Exchanger for further details.

Terminal #10 on

Terminal Board

Connection detail for placing L.W.C.O in 24V circuit

WARNING: Be sure to remove the jumper between H and P1

Water Flow Switch

From

Terminal #9 on Terminal

Bpard

From

Terminal #7 on Terminal

Board

To Terminal #8 on

Terminal Board

PART 5 ELECTRICAL &

CONTROLS

IT IS EXTREMELY IMPORTANT THAT THIS UNIT BE

PROPERLY GROUNDED!

5.1 ELECTRICAL CONECTIONS

Table 14: DynaMax HS Electrical Requirements

DynaMax HS Maximum Amp Draw

Model

Voltage

Requirement

Full Load

Amps

[Amperes]

Maximum Over

Current Protection [Amperes]

81, 82, 83

120VAC, 60Hz,

Single Phase

4 15

101, 102, 103 4 15

151, 152, 153 4 15

201, 202, 203 4 15

211, 212, 213 4 15

251, 252, 253 4 15

261, 262, 263 4 15

291, 292, 293 4 15

391, 392, 393 4 15

501, 502, 503 4 15

601, 603 4 15

701, 703 6 15

801, 803 6 15

602, 702, 802

230VAC, 60Hz,

Single Phase

8 15

The appliance, when installed, must be electrically grounded in accordance with the requirements of the authority having jurisdiction or in the absence of such requirements, with the latest edition of the National Electrical Code ANSI/NFPA No.

70. When the unit is installed in Canada, it must conform to the Canadian Electrical Code, C22.1, Part 1 and/or local Electrical Codes.

• All wiring between the appliance and field installed devices shall be made with wire having minimum 220ºF (105ºC) rating.

• Line voltage wire exterior to the appliance must be enclosed in approved conduit or approved metal clad cable.

• The pump must run continuously when appliance is being fired.

• To avoid serious damage, DO NOT ENERGIZE the appliance until the system is full of water. Ensure that all air is removed from the pump housing and piping before beginning initial operation. Serious damage may result if the appliance is operated without proper flow.

• Provide the appliance with proper overload protection.

• All wires being placed into the terminal block should be

horizontal for at least an inch to ensure sufficient electrical conductivity.

5.2 HIGH LIMIT

A manual reset fail-safe high limit aqua-stat control is inside the appliance and the control bulb is installed in a dry well in the heat exchanger outlet. The setting of this control limits maximum discharge water temperature to 210oF (CPVC, AL29-4C, Stainless) and 185oF (PVC). The temperature of the outlet water in the heat exchanger must drop a minimum of 30°F (16.7°C) below the setting of the high limi t control before the reset function can be activated.

5.3 DYNAMAX HS CONTROLLER

This appliance uses a direct spark ignition control system. The operation of the DynaMax HS Controller for the direct spark igniter proves the presence of main flame using a flame sensor proof current (0.8µA). A status of Ignition Failed will be displayed on the main panel if the boiler fails to light after three (3) consecutive ignition attempts.

Figure 22: DynaMax HS Controller

Table 15: Connector Description

Connector

Connector Description

Flame Sensor, Ground Rod

Fan Modulation

Display, Lead lag, Modbus Comm.

24VAC Power, Pump, VFD

Gas Valve, Safety Interlock String

Safety Annunciation, Remote Operator

24VAC Power, Inlet, Outlet Sensor

DHW, Stack Sensor

5.3.1 SERVICE PARTS

The DynaMax HS Controller is not repairable. Any modification or repairs will invalidate the warranty and may create hazardous conditions that result in property damage, personal injury, fire, explosion and/or toxic gases. A faulty direct spark igniter MUST be replaced with a new factory part. DO NOT use general purpose field replacement parts. Each appliance has one DynaMax HS Controller, one direct spark igniter and one flame sensor. A list of recommended spare parts is illustrated in parts breakdown in this manual.

5.3.2 IGNITION MODULE LOCKOUT FUNCTIONS

The DynaMax HS Controller may lockout in either a manual reset condition requiring pushing the reset button to recycle the control for a CSD1 requirement or an automatic reset condition. Pushing the “OK” with the control in a hard lockout condition is the only way to reset the DynaMax HS Controller. Turning the main power “OFF” and then “ON” or cycling the thermostat will not reset a hard lockout condition. Wait until the display has synchronized before pushing the “OK” button to clear a manual reset condition. The DynaMax HS Controller may proceed into a soft lockout condition. The boiler will stay in the automatic reset state until the fault is corrected and will automatically return to normal operating state.

5.4 ERROR TABLE

5.4.1 Manual Reset Codes

Table 16: Manual Reset Codes*

# Description

0 None

1-31 Internal hardware error

47 Flame rod to ground leakage

49 24VAC low/high 64 Fan speed not proved, ignition failure 67 Blocked flue condition 79 Heater Outlet high limit tripped

Stack limit tripped (PVC: 149oF, CPVC: 194oF, PPE: 230oF, SS, AL29-4C: 250oF)

91 Inlet sensor fault

92 Outlet sensor fault

93 DHW sensor fault

95 Stack sensor fault 96 Outdoor sensor fault

105 Flame detected out of sequence 106

Flame lost in Main Flame Establishing Period

(MFEP) 107 Flame lost early in run 108 Flame lost in run 109 Ignition failed 112 Pilot test flame timeout 113 Flame circuit timeout 149 Flame detected

* To eliminate the hard lockout error,

1) Press the button to clear the error on screen

5.4.2 Automatic Reset Codes Table 17: Automatic Reset Codes

# Description

0 None

29 Burner switch turned OFF

30 Burner switch turned ON

47 Flame rod to ground leakage

49 Abnormal 24Vac voltage

50 Modulation Fault

61 Anti-short Cycle

62 Fan speed not proved

67 Interlock Off, safety circuit is open

69 Pilot test hold

78 Demand lost in run

79 Outlet high limit tripped (internal limit) 81 Delta-T limit exceeded (30oF)

91 Inlet sensor fault

92 Outlet sensor fault

93 DHW sensor fault

95 Stack sensor fault

96 Outdoor sensor fault

97-

Internal Fault

128 Fan speed failed during prepurge 129 Fan speed failed during preignition 130 Fan speed failed during ignition 131 Fan movement detected during standby 132 Fan speed failed during run 137 Interlock failed to close, safety circuit is open 110 Ignition failure occurred 111 Flame current below threshold (0.8Vdc) 149 Flame detected

150,

291

Flame not detected

301

309

Interlock Off, safety circuit is open

460 Interlock off during burn, safety circuit is open 614

Lead boiler was rotated based on measured run

time

PART 6 CONTROL PANEL

6.1 DYNAMAX HS CONTROLLER

The appliance is provided with an operator interface panel at the front. On a DynaMax HS Wall Hung boiler the DynaMax HS Controller can be accessed by removing the upper stainless steel jacket and the lower black sheetmetal jacket which are each held on by two (2) screws. On a DynaMax HS Floor Mount boiler the DynaMax HS Controller can be accessed by carefully lifting off the black-coloured top cover which is held on by four (4) snap lock fasteners.

6.2 SETTING THE DYNAMAX HS CONTROLLER

Button

Description

Back button to return to previous menu Information button

Home Button returns screen to home screen Navigation buttons

Confirm selection

The 5-way control pad allows for easy access to various functions on the DynaMax HS controller. A button allows

for immediate information concerning boiler operation including temperatures, boiler status and any errors that are occurring. The Boiler Temperature Controller for this appliance is the Honeywell SOLA. It initiates the local call for heat and sets the target return (appliance inlet) water temperature. This controller offers a range of operation modes which provides set point as well as modulating control. It provides the following:

• Readings of inlet and outlet water temperatures as well

as flame signal.

• Operation as an auto reset limit.

• Operation as a control for inlet water temperature, outlet

temperature, system temperature.

• Available tank mounted sensor used in conjunction with

inlet sensor.

• Adjustable; target temp, inter-stage differential, on delay

between stages, minimum on time per stage, minimum off time per stage.

• Flame failure signal.

• Error message display in text

• Manual override of boiler input rate for combustion

• Pump exercising feature runs pump 10 seconds every

three days in the event of no pump operation.

Levels of Access

Two levels of access to simplify the use of the boiler. User – Access to general boiler and display settings and

adjustments to the central heating and domestic hot water setpoint.

Installer – Access to all user parameters and allows for changes to additional boiler parameters to allow for ease of startup and serviceability.

The screenshot below displays the default homescreen.

Figure 24: Home Screen

The first five parameters can be user customizable to reflect the most vital information required on the boiler. The list of available parameters is outlined in the table below. This can be done by pressing:

2) Scroll to Display Setup, press

3) Select the line item that is required to be altered, press

4) Select parameter, and press

PARAMETER DESCRIPTION

Standard parameters

System setpoint Indicates active setpoint Operating temp

Indicates temperature at modulation sensor (Default: inlet sensor)

Outlet Outlet Water Temperature [oF] Inlet Inlet Water Temperature [oF] Outdoor Outdoor Temperature [oF], if equipped

Additional user configurable parameters

Delta T

Outlet and Inlet water temperature differential

[oF] LL Operating Temp

Indicates temperature at modulation sensor, if

equipped (Default: S5: system sensor) LL system

setpoint

Indicates active lead lag setpoint Fan speed Actual fan speed [RPM]

Flame signal Actual flame signal [Vdc] Firing Rate Target fan speed [RPM] DHW DHW Temperature [oF] ], if equipped Stack Stack Temperature [oF], if equipped 4-20mA 4-20mA input, if equipped

PARAMETER

DESCRIPTION

Boiler name DynaMax HS model State Indicates current boiler operation sequence

Demand

Indicates origin of call for heat (CH, DHW, Lead Lag)

Access Status User, Installer Outdoor Outdoor Temperature [oF], if equipped

Error

Alert or Lockout. Section 5.4 provides additional details.

Pressing provides additional troubleshooting information on the diagnostic screen.

Figure 25: Diagnostic Screen

PARAMETER

DESCRIPTION

Boiler pump Pump A Auxilary

Pump

Pump B. 3-way valve diverter operation

DHW Pump Pump C. Additional contact rated for 1/6hp.

Sequence of Operation

Pump A is energized for any call for heat Pump B is energized on CH Pump C is energized on DHW

Interlock: Flow switch, LWCO (if equipped), Blocked flue switch (N/C), Low gas switch (4.5” w.c., N/O), High gas switch (14” w.c., N/C)

Pressing provides additional temperature information.

Figure 26: Temperature screen

Central Heat Programming Instructions

Modulation: Boiler Inlet, Boiler Fixed Setpoint Operation (Standalone)

Description

Electrical

Connection(s)

Programming Instructions

•

Boiler operates at a fixed

setpoint

• Modulates on boiler inlet

sensor (default)

• Heat demand is generated

when Remote Operator is closed.

1) Place both toggle switches to

LOCAL

2) Press

and select Login,

Select Quick Start

4) Select CH Setpoint, and enter desired setpoint using 5-way control

The setpoint can be chaged on screenby using the or buttons and press

5) Place Local/Remote switch to REMOTE for remote enable operation (if

required)

Modulation: Boiler Inlet, Outdoor Reset Operation (Standalone)

Description

Electrical Connection(s)

Programming Instructions

•

Boiler operates with variable

setpoint determind by outdoor reset curve

• Modulates on inlet sensor

(default)

• Heat demand is generated

when Remote Operator is closed.

1) Place both toggle switches to

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select CH Config

5) Select Outdoor Reset Config

6) Select Outdoor Reset and Press and select Enable

7) Set Max outdoor temp (Warm weather shutdown, WWSD)

8) Set Min outdoor temp (Outdoor Design)

9) Set Low Water temp (Min. Water Temp.)

10) Set Outdoor boost max off point (Design Max.)

11) Select Sensor Configuration

12) Select Outdoor temp src and Press

13) Select S5 and Press

14) Place right hand toggle switch to REMOTE for remote operation (if

required)

Modulation: System Sensor, Outdoor Reset Operation (Standalone) NOTE: Outdoor Reset Module (PN: 50022037-001) and outdoor sensor (PN: C7089U1006) required

Description

Electrical Connection(s)

Programming Instructions

•

Boiler operates with variable

setpoint determind by outdoor reset curve

• Modulates on system sensor

• Heat demand is generated

when Remote Operator is closed.

1) Connect Remote Operator

2) Connect System sensor to System/Outdoor contacts

3) Connect Outdoor Sensor to J3 ECOM connector

4) Place both toggle switches in LOCAL

5) Press

and select Login

Select Advanced Setup

7) Select CH Config

8) Select Outdoor Reset Config

9) Select Outdoor Reset and Press and select Enable

10) Set Max outdoor temp (Warm Weather shutdown, WWSD)

11) Set Min outdoor temp (Outdoor Design)

12) Set Low Water temp (Min. Water Temp.)

13) Set Outdoor boost max off point (Design Max.)

14) Select Sensor Configuration

15) Select Outdoor temp src and Press

16) Select EnviraCOM and Press

17) Select Select CH Config (twice)

18) Select Modulation sensor = S5

19) Place right hand toggle switch to REMOTE for remote operation (if

required)

4-20mA/ 0-10Vdc Setpoint Operation (Standalone) Consult Additional Boiler Parameters section in manual on page 33 using parameter address 583 and 584.

4-20mA/ 0-10Vdc Firing Rate Operation (Standalone)

Description

Electrical Connection(s)

Programming Instructions

•

Boiler operates with variable

setpoint determined by 420mA incoming signal

• Modulates on header sensor

• Heat demand is generated

when Remote Operator is closed and 4-20mA or 010Vdc signal is present.

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select CH Config

5) Select Modulation rate source = 4-20mA and burner on/off

6) Place right hand toggle switch to REMOTE for remote operation (if required)

Domestic Hot Water Programming Instructions

Modulation: Fixed Setpoint Operation (Standalone)

Description

Electrical Connection(s)

Programming Instructions

•

Boiler operates at a fixed

DHW setpoint

• Modulates on boiler inlet

sensor (default)

• Heat demand is generated

when Remote Operator is closed.

DHW Sensor/ Stat, if required.

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select DHW Config

Inlet Sensor operation

5) Select Demand switch = Sensor only, and Press

6) Select Mod sensor = Inlet, and Press , go to step 7

DHW Stat operation

5) Select Demand switch = DHW switch, and Press

6) Select Mod sensor = Inlet, and Press , go to step 7

DHW Sensor operation

5) Select Demand switch = Sensor only, and Press

6) Select Mod sensor = DHW, and Press

7) Select DHW Setpoint, and enter desired setpoint using 5-way control

8) Place right hand toggle switch setting to REMOTE for remote operation (if

required)

Instantaneous DHW with Brazed Plate Heat Exchanger (combination models)

Description

Electrical Connection(s)

Programming Instructions

•

Boiler operates at a fixed

DHW setpoint

• Modulates on boiler inlet

sensor (default)

• Heat demand is generated

when Remote Operator is closed.

DHW Sensor/ Stat, if required.

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select DHW Config

5) Select Demand switch = Plate Heat Exch, and Press

6) Select Mod sensor = DHW

7) Select DHW Setpoint, , and enter desired setpoint using 5-way control

8) Place right hand toggle switch setting to REMOTE for remote operation (if

required)

Lead Lag Programming Instructions

Master Boiler

Description

Electrical Connection(s)

Programming Instructions

•

Master boiler lead lag setup

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select System

5) Select System ID & Access

6) Verify MB1 Modbus address = 1

7) Verify MB2 Modbus address = 1

8) Select Lead Lag Config

9) Select Lead Lag Master Config

10) Select Master enable = Enable

Fixed Setpoint operation

11) Select Setpoint, and enter desired setpoint using 5-way control

4-20mA/ 0-10Vdc setpoint operation

11) Select Setpoint Source = 4-20mA, and Press

12) Consult Additional Boiler Parameters section in manual on page 33 using

parameter address 560 and 561.

13) Select Lead Lag Slave Config

14) Select Slave enable = Enabled via SOLA master, and Press

Slave Boiler

Description

Electrical Connection(s)

Programming Instructions

•

Slave boiler lead lag setup

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select System

5) Select System ID & Access

6) Select MB1 Modbus address = 2. To be in sequential order

7) Select MB2 Modbus address = 2. To be in sequential order

8) Select Lead Lag Config

9) Select Lead Lag Slave Config

10) Select Slave enable = Enabled via SOLA master, and Press

Outdoor Sensor connected to Slave boiler 2 (DRH ONLY)

Description

Electrical Connection(s)

Programming Instructions

•

Slave boiler outdoor sensor

configuration

• When done correctly, the

outdoor temperature will be shown on the Master boiler

Slave Boiler

1) Place both toggle switches in LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select Sensor Configuration

5) Select Outdoor temp src and Press

6) Select S5 and Press

Master Boiler

7) Place both toggle switches in LOCAL

8) Press

and select Login

Select Advanced Setup

10) Select Lead Lag Config

11) Select Lead Lag Outdoor Reset

12) Select Outdoor reset enable = Enable and press

13) Set Max outdoor temp (Warm weather shutdown, WWSD)

14) Set Min outdoor temp (Outdoor Design)

15) Set Low Water Temp (Min. Water Temp.)

16) Set Outdoor boost maximum off point (Design Max.)

17) Select CH Config

18) Select Warm weather shutdown

19) Select Warm weather shutdown = Shutdown after demand has ended and

press

20) Select Warm weather shdn setpoint

Base load rate adjustment

Description

Electrical Connection(s)

Programming Instructions

•

Upon a call for heat the lead

boiler will fire to the specified base load rate (80%). If the temperature is not within Error threshold (5oF) of setpoint after Interstage delay (2 minutes) a lag boiler will be brought online and will also fire at the base load rate specified.

• Modulation of boilers will

only occur after all boilers in the Lead Lag system are firing at the specified base load rate (80%).

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

1) Select Lead Lag Config

2) Select Lead Lag Master Config

3) Select Base load common rate = 80.0%, and press

Additional Boiler Parameter Instructions

There are some parameters that are not accessible through the Advanced Setup within the HAPI display.

Temperature related parameters must be entered in degrees Celcius. For example, 50oF = 10.0oC. The value “100” is entered into the display. Refer to the next page for a conversion table.

Safety related parameters should not be altered as this will send the control into a Lockout 2 condition, and the HAPI display cannot recover from this. If such an issue arises, the R7910B1009 Honeywell SOLA ignition control needs to be replaced.

To adjust non-accessible parameters: Press > Advanced Setup > System Config > System Config > General Config

1) Locate the parameter that requires adjustment and cross reference with Address Number in the table below

2) Select Adj addr > Enter desired address number > Select OK

3) Select Read and press . Check on screen R/W result: Read OK

4) Select Adj value > Enter desired value > Select OK

5) Select Write and press

Parameter

Address

# Parameter Value

Lead Lag Parameters

Lead Lag modulation back up sensor

559 0 = No backup sensor

1 = Outlet sensor from lead boiler (Default) 2 = Average outlet sensor from all slave boilers

Lead Lag CH 4ma water temperature

560 -

40 –

130oC, (Default: 160

F = 71oC)

Lead Lag CH 20mA water temperature

561 -

40 –

130oC, (Default: 160

F = 38oC)

Lead selection method

574 1 = equalize run time (default)

Lag selection method

575 0 = sequence

order

1 = equalize run time (default)

Add-stage error threshold

718 0 –

130oC, (Default: 5

F = 3oC)

Add-stage inter-stage delay 722 0-64800 seconds, (Default: 120 seconds)

Drop-stage threshold

727 0 –

130oC, (Default: 5

F = 3oC)

Drop-stage

inter-stage

delay 731 0-64800 seconds, (Default: 120 seconds)

Lead rotation time

733 0-64800 minutes, (Default: 60 minutes)

Standalone Parameters

CH Enable

208 0 = Disabled, 1 = Enabled

DHW Enable

448 0 = Disabled, 1 = Enabled

CH 4mA water temperature

583 -

40 –

130oC, (Default: 160

F = 71oC)

CH 20mA water temperature

584 -

40 –

130oC,

(Default: 160

F = 38oC)

DHW priority time 452 0 = Disabled (Default)

>0 = DHW priority time (seconds)

After this timer has expired the heater will revert to CH demand

DHW priority source

463 0 = Disabled (Default)

1 = Enables DHW priority algorithm

Combination Parameters

Plate preheat setpoint 689 -40 – 130oC, (Default: 120oF = 49oC)

Plate preheat on hysteresis

691 -

40 –

130oC, (Default: 5

F =

3oC)

Plate preheat off hysteresis

692 -

40 –

130oC, (Default: 5

F = 3oC)

Plate preheat minimum on time

693 0 –

64800 seconds, (Default: 60 seconds)

Tap detect degrees

694 Rate of temperature drop in DHW sensor when tap detection is declared

0 –

130oC,

(Default: 2

F/ second = 1.1

C/second)

Tap stop DHW

Inlet degrees

697

ΔT between DHW and Inlet when tap demand is stopped. (Default: 10oF = 6oC) For an indirect storage tank, use 20oF = 11.1oC

Tap stop Outlet

Inlet degrees

698

ΔT between Outlet and Inlet

when tap demand is stopped. (Default: 4

F = 6oC)

For an indirect storage tank, use 2

F = 1.1oC

Tap detect on threshold

699 When DHW reaches this temperature, heater activates DHW tap

algorithm

(Default: 115oF = 46oC)

Fahrenheit [oF] Celcius [oC] Enter Into Display

-20 -28.9 -289

-10 -23.3 -233 0 -17.8 -178

10 -12.2 -122 20 -6.7 -67 30 -1.1 -11 40 4.4 44 50 10.0 100 60 15.6 156 70 21.1 211 80 26.7 267

90 32.2 322 100 37.8 378 110 43.3 433 120 48.9 489 130 54.4 544 140 60.0 600 150 65.6 656 160 71.1 711 170 76.7 767 180 82.2 822 190 87.8 878 200 93.3 933

Boiler Setup Programming Instructions

Adjust lightoff rate

Description

Programming Instructions

•

Adjust ignition speed on

lightoff

• This may need to be adjusted

to achieve smooth lightoffs cannot be achieved through combustion settings

• All DynaMax HS boilers leave

the factory with an ignition fan speed of 3000 RPM

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select Burner Control Ignition

5) Select Adjustable lightoff rate, and enter desired lightoff rate using 5-way control and press

Adjust stack limit

Description

Programming Instructions

•

Adjust stack limit based on

vent material used

• PVC: 149

• CPVC: 194

• PP, AL29-4C, Stainless steel:

230oF

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Quick Start

4) Select Stack Limit

5) Select Preferred Stack limit, and enter desired stack limit rate using 5-way control and press

View burner run time, pump cycles

Description

Programming Instructions

•

To view burner run time,

pump cycles for maintenance and service purposes

1) Place both toggle switches in

LOCAL

2) Press

and select Login

Select Advanced Setup

4) Select System Config

5) Select Statistics Config

PART 7 COMPONENTS

7.1 DIRECT SPARK IGNITER

The direct spark igniter is inserted directly through the combustion chamber front door and held in place by two torx-20 screws. Care must be taken when removing and/or installing the igniter. Always remove the igniter prior to removing the fan assembly for inspection of the burner and heat exchanger.

Figure 27: Direct Spark Igniter

During a trial for ignition sequence a properly operating igniter will generate a continuous spark with a 9/64” (3.6mm) spark gap. It is recommended to clean the direct spark igniter using steel wool as required. DO NOT use sandpaper or grit-cloth since this will contaminate the metal surface.

7.2

FLAME SENSOR

The flame sensor is inserted directly through the combustion chamber front door and is screwed into the combustion chamber front door by torx-20 screws. Care must be taken, when installing the flame sensor, to align it perpendicular to the fan flange and parallel to the burner tube and not to over tighten.

Figure 28: Flame Sensor

The ignition module relies on the flame sensor to provide a flame rectification signal. Oxide deposits, improper placement or damaged ceramic insulator will result in insufficient signal leading to ignition module lock out. For proper operation minimum 0.8Vdc must be fed back to the module. Oxide deposit on the sensor rod must be removed with steel-wool. DO NOT use sand-paper or grit-cloth since this will contaminate the metal surface.

7.3 COMBUSTION AIR FAN

DynaMax HS uses a modulating air fan to provide combustible air/gas mix to the burner and push the products of combustion through the heat exchanger and venting system. The fan assembly consists of a sealed housing and fan wheel constructed from spark resistant cast aluminum. The fan is operated by a fully enclosed 120 VAC, SinglePhase EC/DC electric motor. The fan housing and motor assembly is fully sealed and SHOULD NOT be field serviced. The power draw of the motor is proportional to the modulated gas input rate of the appliance.

7.4 GAS VALVE

Figure 29: DynaMax HS 80 -250/260 Gas Valve

Figure 30: DynaMax HS 299 -399 Gas Valve

The gas valve supplied with the DynaMax HS boiler is a combined valve/venturi assembly. A servo pressure regulator is incorporated into the gas valve to provide stable gas supply. Pressure taps are provided to check inlet and outlet gas pressures. An internal fine mesh screen is incorporated in the inlet of the gas valve to prevent debris from entering the combustion chamber. Gas valves are factory set at low and high fire and modulates to maintain combustion characteristics across the full operating range.

7.5 OUTER JACKET

The outer jacket assembly is constructed from mirror finish stainless steel. This ensures a long life for the jacket assembly, with full integrity

Inlet gas

pressure

Inlet gas

pressure

PART 8 TROUBLESHOOTING

Table 18: Troubleshooting Table

COMPONENT

FAILURE MODE

ANALYSIS

Incoming Power

• Two wires interchanged • No effect on safety

• Live and Neutral wires are interchanged.

Transformer Tripped

• The 24Volts and 120 Volts wired are interchanged • Transformer immediately burns out, replace transformer

Pump Fails to Circulate

• Wiring Issue • Check that wires are correctly wired from the DynaMax HS Controller to the pump delay relay.

• Check that 115V is delivered to pump coil.

• Faulty Pump on a wet rotor pump • Pump impeller may be stuck. Use a flat head screwdriver on face of pump to turn impeller manually

• Replace Pump

• Air in the piping system

• Purge all air from the piping system

• Internal Fault on DynaMax HS

Controller

• Replace DynaMax HS Controller

Relief Valve

• System pressure exceeds relief

valve setting

• Replace the standard relief valve with a higher rated valve up to the maximum pressure of the heat exchanger. Improperly sized expansion tank.

Flow Proving Device/ LWCO

• Flow Proving Device/ LWCO contacts are open

• Verify LED’s on current sensing transformer during a heat demand (wall hung)

• Check flow switch paddle (floor mount)

• Verify for closed valves or obstructions in boiler piping

• Verify that all air has been purged from the system

• Verify that wiring is correct

Flame Failure

(Pressing the manual OK button on the DynaMax HS Control Panel to restart the ignition sequence)

• The boiler has failed to ignite the burner after 3 consecutive attempts

• Verify that all air has been purged from gas line

• Inspect spark electrode and related wiring for damage and connection errors

• Verify that the ignition fan speed is set to 3000 RPM through fan diagnostics screen.

• Verify that boiler is properly grounded

• Verify incoming gas supply pressure and that it coincides with Table 9.

• Verify that the vent/ air inlet piping (if equipped) are correctly installed and obstructions are not present.

• Check wiring from DynaMax HS Controller, Gas Valve Transformer and Gas Valve Relay. If a signal cannot be detected, the DynaMax HS Controller needs to be replaced

• If 24 VAC is present, check the outlet of the valve to ensure that gas is flowing. With a manometer connected to the outlet pressure tap of the gas valve a negative pressure should be present during pre-purge. When the valve is energized a change in pressure should occur, if no change is detected the gas valve has failed to open or it is passing insufficient amount of gas. If this is an initial startup increase the low fire gas setting by ¼ turn clockwise.

• Inspect flame sensor and associated wiring. Replace if necessary

• Inspect the burner. Refer to Burner Maintenance in section

9.7

• Replace the DynaMax HS Controller

SYMPTOM FAILURE MODE ANALYSIS

Flame Disappears During a Run Cycle

(Pressing the manual OK button on the DynaMax HS Control Panel to restart the ignition sequence)

• The DynaMax HS boiler was running and flame signal suddenly disappeared.

• Lockout: 106, 107, 108, 109

• Alert 149, 150

• Verify that minimum fan speed is greater than 2500 RPM

• Verify that all air has been purged from gas line

• Inspect spark electrode and related wiring for damage and connection errors.

• Verify that boiler is properly grounded

• Verify incoming gas supply pressure and that it coincides with Table 9.

• Verify that the gas line connections to the boiler are adequate

• Verify that the vent/ air inlet piping (if equipped) are correctly installed and obstructions are not present

• Verify that 24 VAC is being supplied to the gas valve during ignition. If a signal cannot be detected, the transformer needs to be replaced

• Inspect flame sensor and associated wiring. Replace if necessary

• Inspect the burner. Refer to Burner Maintenance in section

9.7

• Replace the DynaMax HS Controller if necessary

Noisy Operation

• Supply Gas Issue

• Refer to Part 3 Gas Connection in this manual.

• Natural Gas Pressure should read between 3” w.c. and 14” w.c.

• L.P. Gas Pressure should be at 11” w.c.

• Air/Gas Mixture Issue • Refer to Gas Valve Adjustment Procedure in section 10.2 of this manual for the proper combustion setting.

• Air Inlet and/or Vent configuration

• Refer to Part 2 Air Inlet and Venting

• Dirty/ Damaged burner • Refer to Burner Maintenance in section 9.7 of this manual for the burner removal and inspection procedure. Clean or

replace the burner, if required.

• Air in the piping system

• Purge all air from the piping system

• Incorrect igniter gap

• Check that spark gap is 9/64”

Auto Reset High Limit Trips

• The outlet temperature has

exceeded the setpoint temperature specified.

• Alert 63, 67, 79, 137, 276-281

• ILK off

• Verify that the system is full of water and that all air has been properly purged from the system.

• Verify that the boiler is piped properly. Refer to Piping Diagrams in Section 13 of this manual.

• Verify that 120VAC is being supplied to the boiler pump on a call for heat. If voltage cannot be detected check wiring.

• Verify that the pump is circulating when 120VAC is detected. If not, pump impeller may be stuck. Use a flat head screwdriver on face of pump to turn impeller manually, if possible.

• If 120VAC is present during a call for heat, but the pump still does not circulate, replace the pump.

• Replace the main

DynaMax HS

Controller if necessary

Manual Reset High Limit Trips

• Manual Reset Safety High Limit tripped, outlet temperature in excess of 210oF

• Alert 63, 67, 79, 137, 276-281

• ILK off

• Verify that the capillary tube is broken. If this is the case,

replace Manual Reset High Limit

• Verify that the system is full of water and that all air has

been properly purged from the system.

• Verify that the boiler is piped properly. Refer to Piping

Diagrams in Section 13 of this manual.

• Verify that 120 VAC is being supplied to the boiler pump

on a call for heat. If voltage cannot be detected check wiring.

• Verify that the pump is circulating when 120 VAC is

supplied. If so, pump impeller may be stuck. Use a flat head screwdriver on face of pump to turn impeller manually.

• If 120 VAC is present during a call for heat, but the pump

still does not circulate, replace pump.

SYMPTOM FAILURE MODE ANALYSIS

Temperature Overshoot

• Stack temperature has exceeded the limit set on the boiler.

• Alert 125, 353

• PVC: Reduce desired setpoint to less than 140oF.

• Measure the resistance of the flue sensor at room temperature, it should be approximately 10kΩ.

• PVC: 149oF

• CPVC: 194oF

• PPE: 230oF

• Stainless Steel, AL29-4C: 250oF

• Outlet temperature has exceeded limit temperature

• Alert 63, 67, 79, 137, 276-281

• ILK OFF

Verify that the system is full of water and that all air has

been properly purged from the system

• Verify that the boiler is piped properly.

• Verify that adequate power is supplied to pump on a call for heat. If voltage cannot be detected check wiring

• Verify pump is circulating when power is supplied. If so, pump impeller may be stuck.

• If power is present during a call for heat, but the pump still does not circulate, replace the pump.

• Replace the Dyna

Max Controller, if necessary.

Sensor Not Connected

• Inlet sensor, Alert: 91

• Outlet sensor, Alert: 92

• DHW sensor, Alert: 93

• Flue sensor, Alert: 95

• Outdoor sensor, Alert: 96

• Verify that the sensors are connected

• Verify that they are wired correctly.

• Measure the resistance of the sensors, 10kΩ sensors.

• Replace the sensor if necessary

Fan Not Turning

• Fan refuses to rotate

• Alert 122, 123, 128, 129, 130,131, 132

• Check fan power wires

• Fan signal wires are interchanged

• Minimum fan speed must be greater than 1500 RPM

Blocked Flue Switch

• Check gas pressure switches, if equipped

• Alert 63, 67, 79, 137, 276-281

• ILK

OFF

• Blocked flue switch wire(s) is/are loose

• Blocked flue switch is set too light if it trips at full fan

speed, reduce sensitivity by turning screw 1 turn

clockwise.

Flame Detection is out of Sync

• Flame detection is present when no visible signs of a flame exist

• Lockout 105, 158

• Verify supply voltage for proper polarity.

• Check external wiring for voltage feedback

• Check internal wiring for proper connections

• Check the flame sensor and verify that it is clean

• Replace DynaMax HS Controller

Blank Display Screen

• Blank display screen • Check S4 switch position on ignition module. Switch is

pushed towards J5 connector

• Check that display is connected to the standalone connector on the back of the display

Replace fuse with factory 3.15A fuse.

• DO NOT use alternates as it may damage the DynaMax

HS Controller

Internal Fault

• Alert 3-9, 20-31

• Lockout 10-18, 32-46, 58-60 ,97-

99, 143

148

• Reset SOLA

• If fault persists, replace SOLA

Manual Reset Codes*

# Description

0 None

1-31 Internal hardware error

47 Flame rod to ground leakage

49 24VAC low/high

64 Fan speed not proved, ignition failure 67 Blocked flue condition 79 Heater Outlet high limit tripped

Stack limit tripped (PVC: 149oF, CPVC: 194oF,

PPE: 230oF, SS, AL29-4C: 250oF) 91 Inlet sensor fault 92 Outlet sensor fault 93 DHW sensor fault 95 Stack sensor fault 96 Outdoor sensor fault

105 Flame detected out of sequence 106

Flame lost in Main Flame Establishing Period

(MFEP)

107 Flame lost early in run

108 Flame lost in run

109 Ignition failed

112 Pilot test flame timeout

113 Flame

circuit timeout

149 Flame detected

* To eliminate the hard lockout error,

1) Press the button to clear the error on screen

Automatic Reset Codes

# Description

0 None

29 Burner switch turned OFF

30 Burner switch turned ON

47 Flame rod to ground leakage

49 Abnormal 24Vac voltage 50 Modulation Fault 61 Anti-short Cycle 62 Fan speed not proved

67 Interlock Off, safety circuit is open

69 Pilot test hold

78 Demand lost in run

79 Outlet high limit tripped (internal limit)

81 Delta-T limit exceeded (30

91 Inlet sensor fault

92 Outlet sensor fault

93 DHW sensor fault

95 Stack sensor fault

96 Outdoor sensor fault

97-

Internal Fault

128 Fan speed failed during prepurge

129 Fan speed failed during

preignition

130 Fan speed failed during ignition

131 Fan movement detected during standby

132 Fan speed failed during run

137 Interlock failed to close, safety circuit is open

110 Ignition failure occurred

111 Flame current below threshold (0.8Vdc)

149 Flame detected

150,

291

Flame not detected

301

309

Interlock Off, safety circuit is open

460 Interlock off during burn, safety circuit is open 614

Lead boiler was rotated based on measured run

time

Ignition Failed displayed on screen Hold 109: Ignition failed

An ignition error occurs when 3 consecutive attempts at lighting the burner have failed. This is a manual reset error where the technician must press OK to clear the error.

Check for constant spark for 6

seconds across spark igniter

YES

Adjust igniter gap to

3/16” and/or clean

igniter

Check incoming gas pressure is

between 3” and 14” w.c.

Check regulator for

proper static incoming

gas supply pressure

YES

Turn high fire screw counter-

clockwise ¼ turn at a time

Verify gas valve is being powered by

ignition control

Check ignition speed is between

2500 to 3000 RPM using

System Monitor

Adjust ignition speed

to 3000 RPM

YES

Burner lights off and stays on

Check flame sensor for carbon deposits,

and clean if

Position flame sensor

so that it is closer to

the burner

YES

Adjust high fire combustion to

8.5 – 9.0% CO

CO2 < 8.5%

Turn high fire screw

CO2 > 9.0%

Turn high fire screw

clockwise

YES

Adjust low fire combustion to

8.0 – 8.5% CO

CO2 < 8.0%

Turn low fire screw

clockwise

CO2 > 8.5%

Turn low fire screw

counter

clockwise

YES

Recheck high-fire combustion:

8.5 – 9.0% CO

Replace igniter and

graphite igniter

gasket

Hold 67: ILK OFF (Flow Switch, LWCO, Gas Pressure Switch, Blocked Flue Switch) Alert 303: Abnormal Recycle: ILK off during drive to Purge Alert 304: Abnormal Recycle: ILK off during Measured purge time Alert 305: Abnormal Recycle: ILK off during Drive to Pre-igntion Alert 306, 307: Abnormal Recycle: ILK off during Pre-ignition Alert 308: Abnormal Recycle: ILK off during Main Flame Alert 309: Abnormal Recycle: ILK off during Ignition Period

This error can indicate a blocked flue or blocked intake condition, low gas pressure switch tripped (optional) or high gas pressure switch tripped (optional). To identify the safety that is open set the multimeter to Vac and measure the voltage from one contact to ground. The contacts produce a 24Vac when the circuit is closed.

Is vent and/or air intake

blocked?

YES

Clear vent and/or

air intake

termination

High Gas Pressure Tripped?

YES

High gas pressure

switch (C6097B,

N/C) set to 14” w.c.

YES

Check incoming

gas pressure and

reset high gas

pressure switch

Low Gas Pressure Tripped?

YES

Low gas pressure

switch (C6097A,

N/O) set to 3” w.c.

YES

Check incoming

gas pressure and

reset low gas

pressure switch

Turn blocked flue switch set

screw 1-2 turns clockwise,

until burner stays on at high

fire

Is Blocked flue switch (N/C)

closed when fan is not turning?

Replace blocked flue switch

(P/N: 8021205256)

YES

The flow switch is not closed or the low water cutoff (LWCO, optional) was tripped. This is an automatic reset error and as soon as flow is proven this error resolves itself. To identify the safety that is open set the multimeter to Vac and measure the voltage from one contact to ground. The contacts produce a 24Vac when the circuit is closed.

Is pump powered?

Check pump wiring

and pump delay relay

YES

Is there a current

transformer

Check operation of

paddle style flow

switch installed on

outlet of DynaMax HS

YES

Use meter to verify

amperage draw on pump

and verify it with rating label

on pump

Check that automatic

air vent thumbscrew is

loose

YES

Purge air from water lines

Is there a double loop through

the current transformer?

YES

Check for contact closure

across terminals 7 and 8 on

field terminal board (perform

this step after verifying

paddle style flow switch is

operational)

Turn off power to boiler

and loop Black 16 wire

twice through current

transformer

Check wiring from

current transformer or

paddle flow switch to

field terminal board

YES

Check for 24Vac signal at

J5-1

YES

Replace ignition

control

Check wiring between green

field terminal board and

ignition module

Insert jumper wire

across terminals 7 and

8 on field terminal

board (temporary

measure)

Stack limit exceeded displayed on screen Alert 125: Modulation was limited due to stack limit

Alert 353: Abnormal recycle: stack limit

A flue gas error occurs when the stack temperature has exceeded the maximum limit allowed by the vent material. This is an automatic reset error, when the stack temperature drops 20oF below the limit allowed the boiler is allowed to restart and an ignition attempt is made if the call for heat is not yet satisfied. In the event that a setpoint greater than 150oF is selected and PVC venting is used the setpoint must be reduced to below 150oF to avoid nuisance flame failures. If a setpoint greater than 150oF is required, venting with CPVC, AL29-4C, 316LL or PPE is strongly advised. The stack temperature is between 15-30oF above the incoming (return) water temperature to the appliance.

Vent Material Maximum Flue Temperature [oF]

PVC

149

CPVC

194

PPE

230

AL29-4C

300+, limited only by rating of seals

316L Stainless Steel

300+, limited only by rating of seals

Is vent material PVC plastic?

(white in colour)

YES

Adjust CH and/or DHW Setpoint to

150oF or less to avoid

nuisance trips

Select the correct vent

material setting through

boiler display

Alert 291: Abnormal Recycle: Flame was not on at end of ignition Alert 294: Abnormal Recycle: Flame was lost during Run Alert 324: Abnormal Recycle: Hardware flame bias Alert 377: Abnormal Recycle: Hardware flame bias delta

This type of failure indicates a flame rectification signal issue through the flame rod.

Is Flame sensor plug secure?

Fasten flame sensor plug securely to

flame sensor wire and check for

corrosion deposits at wire terminals

YES

Check continuity of flame

sensor wire from flame sensor

to ignition control, J1-2

YES

Remove flame sensor and clean

if necessary

Bend flame sensor

closer to burner

Replace flame sensor and

graphite flame sensor gasket

Replace

sensor wire since corrosion

can affect the perceived flame signal

significantly and position it away from

the heat exchanger

8.1 SETTING THE CORRECT COMBUSTION

1) Switch the main power off to the boiler by placing the toggle switch in the ‘OFF’ position

2) Switch the main power on to the boiler and adjust set point so that boiler begins ignition sequence.

3) Observe the boiler as it goes through its startup cycle and operates at high fire.

4) Insert the combustion measurement probe into the stack when high fire operation is observed. Check to see that fan is running at maximum fan speed using the control panel.

5) The combustion values should reside in the range listed in Table 31. If combustion values are not within this range refer to Section 10.2 Gas Valve Adjustment Procedure to correct this issue.

Table 19: Combustion Values

Natural Gas Propane CO2 CO CO2 CO

Max.

Fire

8.5% - 9.0%

<100

9.5% -

10.0%

<100 PPM PPM

Min. Fire

8.0% - 8.5%

<100

9.0% - 9.5%

<100 PPM PPM

6) When the combustion values are satisfied record these values as Camus requires these for warranty purposes.

7) Remove the combustion measurement device and switch the main power off to the boiler by placing the toggle switch in the ‘OFF’ position.

8) Replace the flue temperature sensor back to its proper location.

8.2 GAS VALVE ADJUSTMENT PROCEDURE

If adjustment of the gas valve is required use the following procedure.

In order to perform adjustments to the gas valve the DynaMax HS must be firing before proceeding.

DM 080 – 250, 260

Figure 56: Venturi & Gas Valve Assembly

To adjust the high-fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set High Fire

Locate the input adjustment screw on the side of the venturi. Turn the screw 1/8 turn in either way for each adjustment to keep track of the adjustments. After adjusting the screw wait a moment for the combustion levels to stabilize before attempting to make any further adjustments. Continue this procedure until combustion levels are satisfied.

Increase CO2

Decrease CO2

High Fire

Adjustment

Counter-

Clock Wise

Clockwise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

To adjust the low fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set Low Fire

The DynaMax HS should respond immediately and fire at minimum fan speed. This screw is covered with a cap, which can be removed using a Torx 40 screwdriver. When the correct combustion values are achieved replace the screw cap back on to the gas valve.

Increase CO2 Decrease CO2

Low Fire

Adjustment

Clockwise

Counter-

Clock Wise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

Gas Valve

Venturi

Low-fire adjustment screw

(use Torx 40 for adjustment, clockwise increases CO2)

High-fire adjustment screw

(use slotted screwdriver for adjustment, counterclockwise increases CO2)

DM 299 – 399

Figure 57: DM 299 – 399 Gas Valve

To adjust the high-fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set High Fire

Locate the high-fire adjustment screw on the top side of the gas valve. The screw can be identified by a red cylinder casing around the screw. Turn the screw 1/8 turn in either way for each adjustment to keep track of the adjustments. After adjusting the screw wait a moment for the combustion levels to stabilize before attempting to make any further adjustments. Continue this procedure until combustion levels are satisfied.

Increase CO2

Decrease CO2

High Fire

Adjustment

Counter-

Clock Wise

Clockwise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

To adjust the low fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set Low Fire

The DynaMax HS should respond immediately and fire at 1500 RPM. When this is achieved locate the low fire adjustment screw as illustrated in Figure 57. When the correct combustion values are achieved replace the screw cap back on to the gas valve.

Increase CO2 Decrease CO2

Low Fire

Adjustment

Clockwise

Counter-

Clock Wise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

DM 500 – 800

Figure 58: DM 500 - 800 Gas Valve

To adjust the high-fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set High Fire

Locate the input adjustment screw on the top side of the gas valve. Turn the screw 1/8 turn in either way for each adjustment to keep track of the adjustments. After adjusting the screw wait a moment for the combustion levels to stabilize before attempting to make any further adjustments. Continue this procedure until combustion levels are satisfied.

Increase CO2

Decrease CO2

High Fire

Adjustment

Counter-

Clock Wise

Clockwise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

To adjust the low fire setting

1) Press the button

2) Select Test and press

3) Select Forced Rate and press

4) Select Set Low Fire

The DynaMax HS should respond immediately and fire at 1500 RPM. When this is achieved locate the low fire adjustment screw as illustrated in Figure 58. When the correct combustion values are achieved replace the screw cap back on to the gas valve.

Increase CO2 Decrease CO2

Low Fire

Adjustment

Clockwise

Counter-

Clock Wise

Select Stop Test to return to normal operation or the boiler will return to normal operation after 5 minutes

Low-fire air gas ratio adjustment

(use Torx 40 for adjustment, clockwise increases CO2)

High-fire air gas ratio adjustment

(Use slotted screwdriver for adjustment, counter-clockwise increases CO2)

Low-fire air/gas ratio adjustment, use slotted screwdriver for adjustment, clockwise increases CO2

Lift top cover to access high fire air/gas ratio adjustment (use 3mm allen key for adjustment, counterclockwise increases CO

Gas Inlet

PART 9 MAINTENANCE

CAUTION

It is important that all gas appliances be serviced by a qualified technician trained by Camus Hydronics. It is in your own interest and that of safety to ensure that all local codes, and all the “NOTES” and “WARNINGS” in this manual are complied with. To service or adjust this appliance, it is imperative that the serviceman utilize a combustion analyzer to read CO2 and CO according to Camus Hydronics recommendations.

Listed below are items that must be checked to ensure safe reliable operations. Verify proper operation after servicing.

9.1 EXAMINE THE VENTING SYSTEM

Examine the venting system at least once a year. Check more often in the first year to determine inspection interval. Check all joints and pipe connections for tightness, corrosion or deterioration. Flush the condensate drain hose with water to clean. Clean screens in the venting air inlet system as required. Have the entire system, including the venting system, periodically inspected by a qualified service agency.

9.2 VISUALLY CHECK MAIN BURNER FLAMES

At each start up after long shutdown periods or at least every six months. A burner view port is located on the combustion chamber front door.

CAUTION

The area around the burner view port is hot and direct contact could result in burns

Figure 31: Normal Burner Flame Profile (short dense

and blue)

• Normal Flame: A normal flame at 100% of burner input is blue, with a well defined flame and no flame lifting.

• Yellow Tip: Yellow tipping can be caused by blockage or partial obstruction of air flow to the burner.

• Yellow Flames: Yellow flames can be caused by blockage of primary air flow to the burner or excessive gas input. This condition MUST be corrected immediately.

If improper flame is observed, examine the venting system; ensure proper gas supply and adequate supply of combustion and ventilation air.

9.3 CLEANING BOILER HEAT EXCHANGER

Figure 32: Heat Exchanger & Burner Assembly

1) Shut down boiler: a) Turn the main power off to the boiler

b) Shut off gas supply at the main manual valve in

the gas piping of the main appliance

c) DO NOT drain the boiler unless it will be

exposed to freezing temperatures. If using antifreeze fluid in the heat exchanger, DO NOT drain.

2) Allow time for the boiler to cool to room temperature if it has been firing.

3) Wall Hung: Remove both the stainless steel upper jacket and the lower sheetmetal jacket.

Floor Mount: Remove front stainless steel panel.

4) Remove igniter and flame sensor electrodes. If necessary, clean with steel wool. DO NOT use sandpaper.

5) Remove the fan/ mixing tube assembly from the heat exchanger door.

6) Remove burner.

7) Examine burner and clean if required as per 9.7.1.

8) Examine heat exchanger surfaces to determine if cleaning is required. If cleaning is required remove the (6) nuts fastening the heat exchanger flange from the heat exchanger.

9) Disconnect the condensate hose from the heat exchanger and connect a 5/8” diameter hose (field supplied) from the bottom of the heat exchanger to a drain

10) Use water proof material to carefully cover the refractory at the rear of the combustion chamber of the heat exchanger.

11) Use a vacuum cleaner to remove any debris that has collected on the heat exchanger surfaces. DO NOT use any type of solvent.

12) Brush the heat exchanger with a nylon bristle brush. DO NOT use a metal brush. Re-vacuum the heat exchanger.

13) Finish cleaning by wiping down the boiler heating surfaces with a clean, damp cloth.

14) Rinse out any additional debris with a low pressure water supply. Start rinsing from the rear of the heat exchanger and slowly working your way towards the front of the heat exchanger.

15) Remove the water proof material after cleaning is complete.

16) Re-install the heat exchanger door by evenly torquing down the (6) nuts to 3 ft-lbs, burner, igniter and flame sensor, and fan/ mixing tube assembly. Fasten the nuts back to the heat exchanger assembly.

17) Re-connect the fan assembly to the boiler mixing tube.

18) Re-connect the condensate hose to the heat exchanger.

NOTE

All gaskets on disassembled components must be replaced with new gaskets/sealant on re-assembly, if required. Gasket kits are available from the factory

CAUTION

When the vent system is disconnected for any reason it must be reassembled and resealed according to vent manufacturer’s instruction

9.4 CONDENSATE TREATMENT

Condensate occurs when the products of combustion are cooled below their dew point in the heat transfer process. The liquid condensate formed from this high efficiency heat transfer process is mildly acidic.

• The condensate will typically have a pH ranging from

4.0 to 5.0 as it is discharged from the condensate drain of the appliance.

• The condensate collection box inside each DynaMax HS where the condensate is collected is constructed of a non-corrosive material.

• All materials external to the appliance in contact with the condensate must be corrosion resistant.

• Condensate must be able to flow freely from the appliance. All condensate flow is accomplished by gravity requiring a minimum downward slope of 1/4” per foot (21mm/m) to ensure proper flow to a suitable drain.

• All condensate piping and connections must be easily accessible for routine maintenance and inspection.

• Use solid piping when running condensate line across the floor.

• Check neutralized pH level regularly or as required by local jurisdiction. Replace neutralizer medium as required.

There are several factors affecting amount of condensation created by the appliance, however for rough approximation use. Condensation Volume, US Gallon/Hr = Input, MBH/1000 x

5.0

Many jurisdictions will require the acidic condensate to be neutralized before it can be placed in a drain system.

• A neutralizer, calcium carbonate, to control the pH of

the liquid discharged to a drain system is provided with every DynaMax HS boiler.

• As the reservoir fills, it provides an extended residence

time to neutralize the condensate.

• Residency time in the neutralizer reservoir allows time

for the pH to be raised.

• Prime the neutralizer reservoir with 1 liter of water.

As the condensate migrates through the reservoir in typical applications the pH is controlled to a range of 5.5 to 6.0 before exiting the system. Always check with local codes for specific requirements.

9.5 IGNITER AND FLAME SENSOR

ELECTRODES

The direct spark igniter is to be checked at every service interval. Clean the direct spark igniter as required to maintain peak ignition efficiency.

1) Turn off main electrical power to the appliance.

2) Turn off main manual gas shutoff to the appliance.

3) Locate the direct spark igniter and flame sensor.

4) Disconnect the power lead to the direct spark

igniter and flame sensor

5) Loosen and remove the two (2) torx screws that

hold the igniter and flame sensor to the heat exchanger flange.

6) Pull the igniter horizontally out of the heat

exchanger flange. Use care, do not hit or break the igniter leads.

7) Remove any debris that has accumulated on the

electrodes using steel wool. If the electrodes cannot be cleaned to their original appearance, replacements are needed. Do not use sand-paper since this will contaminate the surface.

8) Check that the igniter and flame sensor gaskets

are still in good condition (no tears or seams). If the gaskets are in good condition the electrodes can be re-installed back to the heat exchanger flange.

9) Check that the igniter gap is 9/64”.

9.6 CHECK IGNITER GROUND WIRING

1) Inspect boiler ground wire from the heat

exchanger flange to ground on boiler. Check boiler ground wire continuity.

2) Verify that all wiring is in good condition and is

securely anchored.

9.7 BURNER MAINTENANCE

The burner should be removed for inspection and cleaning

on an annual basis. An appliance installed in a dust or dirt contaminated environment will require inspection and cleaning on a more frequent schedule. The fan assisted combustion process may force airborne dust and dirt contaminants, contained in the combustion air, into the burner. With sustained operation, non-combustible contaminants may reduce burner port area, reduce burner input or cause non-warrantable damage to the burner.

Never operate this appliance during construction.

Airborne contaminants such as dust, dirt, concrete dust or dry wall dust can be drawn into the burner with the combustion air and block the burner port area.

9.7.1 Burner Removal and Cleaning

Access to the burner will require the following steps:

• Turn off main electrical power to the appliance.

• Turn off main manual gas shutoff to the

appliance

• Remove the front cover.

• Disconnect the gas supply to the fan inlet.

• Disconnect the fan motor power wires at the

harness.

• Remove the direct spark igniter and the flame sensor.

• Remove the T-25 screws holding the front burner flange in place to gain access to the burner.

• The burner can now be pulled horizontally out of the heat exchanger cavity.

• Use care to prevent damage to the knitted metal fiber of the burner surface.

• Wash the burner with water, such as a garden hose. Never wipe or brush the surface of the burner.

• For optimal results immerse the burner port area in a solution of dishwashing detergent and hot water. DO NOT use chlorine based solvents or cleaning agents on the burner. Allow the burner to remain in the solution for a short period of time to remove, dust, dirt and oil or grease laden contaminants.

• Rinse the burner thoroughly with clean water to remove any residue from the detergent cleaner

• The burner should be air dried after removal from the cleaning solution and rinsing.

• Check all gaskets and replace as necessary. Gaskets affected by heat will not reseal properly and must be replaced.

• Replace the burner in the reverse order that it was removed.

NOTE

When the combustion air fan is removed for any reason, the inlet to the burner must be covered to prevent foreign objects from falling into the burner. Always look inside the burner to check for dents. Do not place a burner back into operation if the inner distribution screen has been dented during the service operation, call the factory for recommendations. Use care when removing and handling the burner, Sharp objects or impact may damage or tear the metal fiber surface rendering the burner unfit for service.

9.8 REMOVAL OF COMBUSTION CHAMBER LINING

The combustion chamber insulation in this appliance contains ceramic fiber material. Ceramic fibers can be converted to cristobalite in very high temperature applications. The International Agency for Research on Cancer (IARC) has concluded, “Crystalline silica in this form of quartz of cristobalite from occupational sources is carcinogenic to humans (Group 1)”. Normal operating temperatures in this appliance are below the level to convert ceramic fibers to cristobalite. Abnormal operating conditions would have to be created to convert the ceramic fibers in this appliance to cristobalite. The ceramic fiber material used in this appliance is an irritant; when handling or replacing the ceramic materials it is advisable that the installer follow these safety guidelines.

• Avoid breathing dust and contact with skin and eyes.

o Use NIOSH certified dust respirator

(N95). This type of respirator is based on the OSHA requirements for cristobalite at the time this documentation was written.Other types of respirators may be needed depending on the job site conditions. Current NIOSH recommendations can be found on the NIOSH website at

http://www.cdc.gov/niosh/homepage.html

. NIOSH approved respirators, manufacturers, and phone numbers are also listed on this website.

o Wear long-sleeved, loose fitting clothing,

gloves, and eye protection

• Apply enough water to the combustion chamber lining to prevent airborne dust.

• Remove the combustion chamber lining from the water heater and place it in a plastic bag for disposal.

• Wash potentially contaminated clothes separately from other clothing. Rinse clothes washer thoroughly.

NIOSH stated First Aid

• Eye: Irrigate immediately

• Breathing: Fresh air

9.9 COMBUSTION AND VENTILATION AIR

Check frequently to be sure that the flow of combustion air to the appliance is not obstructed. Unless air is piped directly to the heater combustion air must be provided to the mechanical room with openings sized per the requirements of the current B149 or National Fuel Gas Code. The DynaMax HS is setup to allow outdoor combustion air to be connected directly to the appliance. It is highly recommended that combustion air be connected directly to the appliance. For installations in a common boiler room with atmospheric appliances or if there is the possibility of negative pressure in the boiler room, the air inlet must be piped directly to the DynaMax HS.

9.10 GAS VALVE VOLTAGE

This appliance uses a transformer to supply a 24 volt signal to the Honeywell SOLA. The voltage on the secondary side should be 24 to 28VAC when measured with a voltmeter. A secondary voltage of 21VAC or less supplied to 24VAC components may cause operational problems.

9.11 COMBUSTIBLE MATERIALS

CAUTION

Keep appliance clear from combustible materials; do not store GASOLINE and other flammable vapors and liquids in the proximity of the appliance.

9.12 FREEZE PROTECTION FOR INDOOR & OUTDOOR INSTALLATIONS

Installations are not recommended in areas where the danger of freezing exists. Proper freeze protection must be provided for appliances installed outdoors, in unheated mechanical rooms or where temperatures may drop to the freezing point or lower. If freeze protection is not provided for the system, a low ambient temperature alarm is recommended for the mechanical room. Damage to the appliance by freezing is non-warrantable.

• Location - Heating boilers, hot water supply boilers or

water heaters must be located in a room having a temperature of at least 40ºF (5ºC).

• Caution - A mechanical room operating under a

negative pressure may experience a downdraft in the flue of an appliance that is not firing. The cold outside air may be pulled down the flue and causing a frozen heat exchanger. This condition must be corrected to provide adequate freeze protection.

• Freeze protection for the appliance using an indirect

coil can be provided by using hydronic system antifreeze. Follow the manufacturer’s instructions. DO NOT use undiluted or automotive type antifreeze.

• Shut-down and draining - If for any reason, the unit is

to be shut off in a space where danger of freezing exists, the following precautionary measures must be taken:

o Shut off gas supply. o Shut off water supply. o Shut off electrical supply. o Drain the main exchanger and the brazed plate

heat exchanger, if supplied, completely.

o Ensure that the pump and connecting piping are

fully drained.

9.13 FREEZE PROTECTION FOR A HEATING BOILER SYSTEM (Optional)

• Use only properly diluted inhibited glycol antifreeze

designed for hydronic systems. Camus recommends using a 30/70 mixture of glycol antifreeze to water. DO NOT exceed a mixture of 50/50.

• Follow the instructions from the antifreeze

manufacturer. Quantity of antifreeze required is based on total system volume including expansion tank volume.

• Antifreeze is denser than water and changes the

viscosity of the system. The addition of antifreeze will decrease heat transfer and increase frictional loss in the boiler and related piping. Where

antifreeze has been used, to maintain the temperature rise across the appliance confirm that the recommended GPM for pure water has been increased by 15% and the head loss by 20%.

• Local codes require a back flow preventer or actual

disconnect from city water supply when antifreeze is added to the system.

• Always follow the chemical manufacturer’s directions

when filling or topping-up the system with water mixed with antifreeze. This will prevent any possible reaction of the water with antifreeze which can create sludge.

PART 10 INSTALLATIONS

WARNING

Before starting the boiler, smell near the floor and around the boiler for any gas odours or any unusual odour. Remove the stainless steel jacket and smell the interior of the boiler. If there is any sign of a gas leak, do not proceed with startup. Repair all the leaks before attempting to start

the boiler.

WARNING

Propane boilers ONLY – Your local propane supplier adds an odorant to the propane gas to allow for propane gas leak detection. In some cases, the added odorant can fade and the gas may not give off any noticeable odour. Before startup have the local propane supplier check for the correct odorant level in the gas.

10.1 CHECKING THE INSTALLATION

• Inspect the connections for water, gas and electricity.

• Inlet gas pressure must be a minimum of 3” W.C. for

natural gas and 11” W.C. for propane.

• With the boiler off, open the main gas supply valve and vent the trapped air from the piping leading to the boiler. Confirm that all gas connections to the heater are tight and that there are no missing test plugs.

Refer to Section 8.1 Setting the Correct Combustion of the manual for recommendations on setting combustion characteristics

10.2 CHECKING THE CONSTRUCTION

• Check the boiler wiring to see that it agrees with the wiring diagram supplied.

• Confirm that all terminal strips and field connections are identified.

• Confirm that the DynaMax HS Controller control is set in the proper mode. In remote mode an external controller determines the set point and the stage contacts on the DynaMax HS Controller are always closed. Auto reset limits are fixed in all Modes.

• With the boiler running, check for flue gas leaks along the inner cabinet joints and around the flue outlet.

• Repair any leaks prior to proceeding to the next step.

• At the factory, adjustments were made to achieve

proper input and acceptable burner performance at full input and at minimum input.

10.3 HEATING BOILER INSTALLATIONS

Before beginning the installation, consult local codes for specific plumbing requirements. The installation should have unions and valves at the inlet and outlet of the appliance so it can be isolated for service. An air separation device must be supplied in the installation piping to eliminate trapped air in the system. Locate a system air vent at the highest point in the system. The system must also have a properly sized expansion tank installed. Typically, an air charged diaphragm-type expansion tank is used. The expansion tank must be installed close to the boiler and on the suction side of the system pump (appliance Inlet) to ensure proper operation. Caution: This appliance should not be operated at less than 12 PSIG cold. Pressure will rise when hot. Expansion tank sizing will determine the pressure when the system is hot. Do not operate the system at less than 18-20 PSIG when hot. Water piping must be supported by suitable hangers or

floor stands, NOT by the appliance. Pipe systems will be subject to considerable expansion and contraction. Pipe supports could allow the pipe to slide resulting in noise transmitted into the system. Padding is recommended. The boiler pressure relief valve must be piped to a suitable floor drain. See Section 4.11.

10.4 INSPECT & RECHARGE CONDENSATE COLLECTION/NEUTRALIZING RESERVOIR

1) Before starting the unit inspect the condensate

reservoir in the DynaMax HS making sure the collection box is intact.

2) Remove screw holding lid on to condensate collection

box. Remove lid from the condensate collection box

3) Examine neutralizer medium and refill as necessary

with fresh medium

4) Fill with fresh water until the water begins to flow out of

drain

5) Re-install the lid and hold-down screw on the

condensate collection box.

WARNING

The condensate collection box must be filled with water to prevent flue gas emissions from escaping during boiler

operation.

CAUTION

A leak in a boiler “System” will cause the fill system to introduce fresh water constantly, which may cause the tubes to accumulate a line/scale build up. Lime/scale buildup leading to heat exchanger failure is NOT covered by warranty.

10.5 WATER CONNECTIONS

System pipe size must be in accordance with Table 10 (depending on model) and, between supply and return lines, must not exceed 50 feet of equivalent length. Connection sizes at the heater are given in Tables 3 & 5. Any reduction in recommended pipe size may decrease flow resulting in high temperature rise across the heat exchanger, boiler noise, flashing to steam and nonwarrantable heat exchanger damage.

10.6 PIPING LENGTHS

The appliance circulator provides the water flow from the primary boiler piping, through the boiler and back to the primary system. Pipe diameter and length are critical to ensure proper flow through the boiler. The secondary loop piping to and from the appliance must have a fully ported ball valve installed in both the supply and return side piping and will be used for isolation only.

The ball valves must be the same diameter as the installed piping. If flow control is required, other means of flow

control such as globe valve or flow setter should be used.

10.7 SUMMARY

a) Typical Boiler Installations

General Plumbing Rules

1) Check all local codes.

2) For serviceability, always install unions.

3) Always pipe pressure relief valve to an open drain.

4) Locate system air vents at highest points of system.

5) Expansion tank must be installed near the boiler and on the suction side of the system pump.

6) Support all water piping.

7) Place drip pan underneath boiler. (if required)

b) Placing the Boiler in Operation

Pre-Start Check List

1) Review the location of the boiler, clearances from combustible surfaces and available service clearances.

2) Review Part 2 Venting. Ensure that all vent components are fabricated from the correct category of materials with adequate clearance from combustibles. Review the vent termination point for proper location and clearances.

3) If a separate combustion air pipe is used, ensure that it is properly sized, sealed and terminated.

4) Review the water piping from the boiler to the system. The boiler must be installed in a primary/ secondary piping system. Review the diameter and equivalent length of the installed piping to and from the boiler to ensure proper flow.

5) Ensure that a properly sized system pump is installed with an expansion tank.

6) Check system pressure. Ensure a minimum of 18-20 PSIG with the system hot and not more than 90% of the rated pressure of the relief valve.

7) Review the installed gas piping from the meter to the boiler. Ensure that the gas pipe, meter and any regulators are adequately sized.

8) Review the field wiring and electrical service for the boiler controls. Ensure that the electrical service(s) is adequately sized.

9) Fill the condensate collector with fresh water until water begins to pour out the drain.

10) Ensure that the boiler condensate drain and all vent system condensate drains are properly routed to an acceptable floor drain.

Boiler Set-Up

1) Ensure that the boiler and piping system are full of water. Bleed all air from the pump housing and secondary loop.

2) Check system for any water leaks.

3) Check system for installation of glycol or water treatment where required. Where glycol has been used to maintain the temperature rise across the appliance confirm that the recommended flow for pure water has been increased by 15% and the head loss by 20% while maintaining a 30-35oF rise across the heat exchanger.

Boiler Operational Checks

1) Turn the boiler main power switch to the “ON” position.

2) Verify operation of the text display on the front panel.

3) Program the adjustable points.

4) Push the reset button if a manual reset error is displayed.

5) Install a manometer on the gas supply to the boiler and verify minimum gas supply pressure as the burner fires at 100% of rated input.

6) Verify operation of safeties as necessary (low water cut-off, high limit, gas pressure, etc.).

Boiler Operation

1) Appliance should begin the start-up process for the sequence of operation.

2) The boiler will fire at approximately 50% of rated input on initial start-up and adjust input as required to meet system demand.

3) Based on system demand, the appliance will modulate accordingly.

4) As system demand is satisfied, the burner will fire at minimum fire for the given demand and the boiler will cycle off when the demand ceases or is interrupted. When this occurs the combustion air fan will decelerate at a preprogrammed rate before the appliance shuts down.

10.8 DOMESTIC HOT WATER WITH STORAGE TANK

Hot water heaters are designed for installation with a storage tank. The piping between the tank and heater and the control of water velocity, as explained below, are important for correct operation of your hot water heater.

10.9 DOMESTIC HOT WATER WITH PLATE HEAT EXCHANGER

The piping between the plate heat exchanger in the DynaMax HS boiler and to an outlet tap is important for correct operation of the plate heat exchanger. The following procedure should be followed for setting the domestic hot water tuning valve:

1) There is a temperature tuning valve inside the DynaMax HS jacket on the domestic hot water outlet from plate exchanger. This valve can be set for field conditions.

2) First identify the highest domestic hot water load.

For example in some cases it may be the bath tub and in some cases it may be the clothes washer.

3) Allow the DynaMax HS to fire up and reach full fire under maximum hot water load demand conditions.

4) Observe the outlet water temperature and close the tuning valve gradually as outlet temperature starts to drop. Allow the system to reach equilibrium between adjustments to the tuning valve.

5) Once the tuning valve is properly set, outlet temperatures will never drop below desired minimum temperature.

6) Seal stem of tuning valve with silicone to prevent unauthorized tampering.

10.10 TEMPERATURE RISE AT FULL FIRING RATE

1) The pump must run continuously when the burner is

firing.

2) With the pump running and the burner in the off cycle,

the inlet temperature and outlet temperature readings on the DynaMax HS Control Panel should read approximately the same temperatures.

3) Turn the appliance on and allow time for the

temperature to stabilize. Check the temperature rise when the burner is firing at 100% of rated input.

4) Compare the temperature rise on the Control Panel

with the required temperature rise at the required flow rate on Tables 20 and 21.

5) Should adjustment be needed, proceed as follows:

If the temperature rise is too high, the water velocity is too low. Adjust as follows:

1) Check for flow restrictions. Check for debris in strainers

2) Check diameter and equivalent length of the piping

between the storage tank and hot water heater.

3) Be sure the pipes between the hot water heater and

storage tank are not more than a total of 50 equivalent feet between supply and return lines. If maximum equivalent length for the specified pipe diameter is exceeded, larger diameter pipe may have to be installed to achieve correct flow and temperature rise.

4) Be sure all valves are open between the hot water

heater and the storage tank. Ensure that all ball valves are fully ported.

5) Check the pump to be sure it is running properly and

that the pump motor is running in the proper direction.

6) Common manifold piping for multiple unit installations

will require larger minimum pipe sizes and tank circulating tapping to ensure proper flow.

The required temperature rise and the recommended pump size are based on the heating of potable water with normal hardness within a typical range of 7.5 to 17.0 grains per gallon. Consult the factory when heating potable water exceeding these specifications. Damage to the heat exchanger as a result of scaling or corrosive water conditions in non-warrantable.

Table 20: Temperature Rise across Heat Exchanger

(Hydronic Heating)

TEMPERATURE RISE ACROSS HEAT

EXCHANGER

MODEL

[BTU/hr]

30oF (16.7oC)

35oF (19.4oF)

USGPM ∆P-Ft. USGPM ∆P-Ft.

,000

5.0

8.2 4.3 6.2

100

,000

6.3 12.3 5.4 9.4

150,000

9.5 10.4 8.1 7.8

199,000

12.6 7.2 10.8 5.8

250,000

15.8 11.5 13.5 8.7

299

,000

18.9 9.3 16.2 7.0

399

,000

25.2 8.4 21.6 6.3

500,000

31.5 9.2 27.0 6.9

600,000

38.8 17.5 32.0 11.8

700,000

45.3 18.2 40.0 14.4

800,000

51.8 23.5 43.0 16.0

Table 21: Temperature Rise across Heat Exchanger

(DHW)

TEMPERATURE

RISE ACROSS HEAT

EXCHANGER

MODEL

[BTU/hr]

0OF (11.

1oC)

USGPM ∆P-Ft.

80,000

7.5 11.5

100,000

9.4 26.9

150,000

14.0 27.8

199,000

19.2 25.9

250,000

23.5 28.3

299,000

28.8 25.8

399,000

38.4 23.9

500,000

48.6 29.4

600,000

57.6 34.2

0,000

70.4 40.0

800,000

77.6 43.2

CAUTION

Temperature rise cannot be adjusted when the burner is firing at less than 100% of input rate.

CAUTION

Adequate care

MUST

be taken to prevent potential scald

injury when storing water at 140°F (60°C) and hotte r.

WARNING

Should overheating occur or the gas supply fail to shut off, do not turn off or disconnect the electrical supply to the pump, instead, shut off the gas supply at a location external to the appliance

10.11 LEAD LAG SETUP

The following components are needed for a Lead Lag setup

1) 10kΩ System Sensor Turn off all the boilers before beginning the setup process. To setup the DynaMax HS lead lag system follow the

instructions:

System Sensor

Insert the supplied 10kΩ system sensor into the building loop. The wires coming out of the system sensor should be connected to pin#5 and #6 of the green DynaMax HS terminal board.

NOTE The use of a system sensor is required in lead lag operation.

1) When variable speed main circulators ARE NOT used

the system sensor is to be placed into the return system piping.

2) When variable speed main circulators are used the

system sensor is to be placed into the supply system piping.

All SOLA controllers are programmed with a default address of 1. The address of the slave controllers in the system must have a unique address (1..8).

Sequence of Operation: When a boiler is set as Lead Lag Master = Enabled and

Modbus address = 1, the controller of this boiler will drive the lead lag operation.

The outdoor temperature sensor connected to the slave boiler 2 (ie. B-2) will be the outdoor sensor for the lead lag system

• The system temperature sensor connected to boiler 1 in terminals labeled “Outdoor System Sensor” on the terminal board will be the control sensor for lead lag operation.

• The start/stop signal connected to boiler 1 at terminals labeled “Remote Operator” will be the heat demand input for lead lag operation.

When demand for heat is present the lead boiler will start and uses the lead lag parameters for boiler modulation. After a period of “Interstage delay” the master boiler compares the lead lag temperature with the lead lag set point and will check if:

1) An additional boiler is needed

Lead lag < Lead lag setpoint – Add stage Error threshold

2) Number of boilers remain the same

Lead lag > Lead lag setpoint – Add stage Error threshold AND Lead lag < Lead lag setpoint + Drop stage Error threshold

3) A boiler should stop Lead lag > Lead lag setpoint + Drop stage Error

threshold

If the lead lag master system is interrupted the remaining boilers will operate as standalone boilers based on the Central Heat or DHW parameters when set to “Enabled”.

Rotation Rotation time is configurable based on equalized run time. For a fixed rotation schedule refer to Additional boiler parameters section on page 33 of this manual, parameter #575 & 733.

Interstage Delay The length of time to wait between requesting a slave boiler to fire and detecting that it has failed to start. (Default: 2 minutes). Access to this parameter is outlined on page 33 of this manual, parameter #722 and 731.

Base Load Rate When a call for heat is initiated the lead boiler runs at the desired base load rate (Default: 80%) and continues to operate in this fashion based on the above 3 scenarios. If the lead lag temperature is not satisfied a second boiler is fired at they would both operate at 80% fire rate.

Slave State

Slave Status Manager

Unknown Table entry is unused or empty

Available Slave is operational and ready to use

Add Stage Stage is getting ready to fire

Suspend

Stage

Stage was getting ready but is not needed

Disabled

Slave is locked out or disabled

Recovering

Slave is in time delay to verify that it is

operational before considered to be available

Wiring the Lead Lag Setup

Use lead lag terminals on the terminal board to wire lead lag appliances

Master Slave 2 .. Slave 7

J3, MB2

A A .. A

B B .. B

Figure 33: Lead lag Wiring Setup (Left: Master, Right: Slave)

NOTE

Recycle power on all boilers after programming is complete if lag boilers are not discovered automatically

NOTE

CH Setpoint or DHW Setpoint must match Setpoint located in Lead Lag Master Configuration in order for the system to operate correctly.

NOTE

The Local/Remote switch (explained below) must be set in the “Local” position on ALL lag boilers.

10.12 LOCAL/REMOTE SWITCH

The local remote switch mounted on the terminal board is designed to generate a call for heat either relying on an external contact closure (Remote) or enabling the boiler locally (local). When Remote is selected via the SPDT switch the Remote Operator contacts on the terminal board must be closed to initiate a call for heat. When Local is selected via the SPDT switch a constant call for heat is generated which will enable the boiler to proceed to a trial for ignition. When troubleshooting the DynaMax HS it is suggested to switch to Local mode. The Local/Remote switch is independent of the 4-20mA/2-10Vdc signal.

10.13 MODBUS/LOCAL SWITCH

The Modbus/Local Switch mounted on the terminal board is designed to relay the signal to the boiler display (local) or accept an incoming signal from Modbus. When local is selected via the DPDT switch the boiler display presents all necessary boiler information. When Modbus is toggled the boiler display will continue to be illuminated with a message showing “Connection lost”. The BMS now overrides the communication link to the boiler.

10.14 APPLIANCE

∗ Remove manometers and tighten test port screws. ∗ Fill out start up report for each heater. Be sure to

record all settings and readings. Retain a copy of report for future reference.

∗ Start up is now complete and heater may be placed

into service.

PART 13 PIPING DIAGRAMS

Figure 31: Single Boiler Hydronic Heating Zoned Piping Arrangement

Note:

1) Size main header to minimize induced flow

through zones

2) Separate boiler loop as shown is recommended

for system piping greater than 50 equivalent feet.

Pressure Reducing

Valve

Pressure Gauge

Ball Valve

Air

Separator

Zone

Circulator

Flow Check Valve

DynaMax HS

Drain

Union

Temperature

/ Pressure

Gauge

Expansion

Tank

Figure 32: Single Combination Boiler Zoned Piping Arrangement

Pressure Reducing

Valve

Pressure Gauge

Ball Valve

Air

Separator

Expansion

Tank

Zone Circulator

Flow Check

Valve

DynaMax HS

Temperature

/ Pressure

Gauge

Drain

Union

Anti-scald Mixing Valve

Note:

1) Size main header to minimize induced flow

through zones

2) Separate boiler loop as shown is recommended

for system piping greater than 50 equivalent feet.

Figure 33: Single Boiler Hydronic Heating & Indirect Storage Tank Zoned Piping Arrangement

Pressure Reducing

Valve

Pressure Gauge

Ball Valve

Air Separator

Expansion

Tank

Zone Circulator

Flow Check Valve

DynaMax HS

Temperature

/ Pressure

Gauge

Drain

Union

Anti-scald Mixing Valve

Note:

1) Size main header to minimize induced flow

through zones

2) Separate boiler loop as shown is recommended

for system piping greater than 50 equivalent feet.

Indirect DHW Tank

Cold

Water In

Hot

Water Out

Figure 34: Single Boiler Hydronic Heating & Direct Storage Tank Zoned Piping Arrangement

Cold

Water In

DHW

Sensor

Union

Direct DHW Tank

Anti-Scald Mixing Valve

Cold

Water In

Hot

Water Out

Figure 35: Multiple Boiler Hydronic Heating Zoned Piping Arrangement

Pressure Reducing

Valve

Pressure Gauge

Air Separator

Expansion

Tank

Ball Valve

Zone

Circulator

Flow Check Valve

DynaMax HS

Boiler

(Master, M1)

Temperature/

Pressure

Gauge

Drain

Union

DynaMax HS

Boiler (Slave, S2)

System

Sensor

Note:

1) Size main header to minimize induced flow

through zones

2) Location of system sensor is based on single

speed building circulator. If a variable speed building circulator is used, the system sensor must be placed in the building supply.

PART 14 EXPLODED VIEW & PARTS LIST

DYNAMAX HS WALL HUNG

DYNAMAX HS FLOOR MOUNT

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

1 Heat Exchanger

4 + 1 Wall X X 5 + 2 Wall X 8 + 4 Wall X X

8 + 4 Floor X X 10 + 6 Floor X 15 + 8 Floor X

18 + 10 Floor X

21 +11 Floor X X

24 + 12 Floor X

2 Burner

221.042.001-A X X

221.039.001-A X

221.041.001-A X X X X

221.037.001-A X

221.038.001-A X X

2437.003 X X

2416.001 X

Heat Exchanger

Flange (complete

with gaskets)

GM20-65-028-01

X X X

GM20-65-033-01

X X X X X X X

GM10-40-091-01

X X X

Heat Exchanger

Flange Nuts

GM10-05-012 X

Igniter

GM10-35-108-01

X X X X X X X X X X

GM10-35-161-01

X X X

6 Flame Sensor

GM10-35-109-01

X X X X X X X X X X

GM10-35-162-00

X X X

Igniter/Flame

Sensor Screws

GM10-05-020 X

DynaMax HS

Controller

R7910B1009 X

DynaMax HS

Display

DSP49G2094B

Condensate

Neutralizer Box

90-15100 X X X X X 90-10030 X X X X X X X X

11 Combustion Fan

150503-00

X X

150563-00

X X X X X X X

55667.14002 X

150930-04

G1G 170

X X X

12 Venturi

45900-444-003

X X

45900-444-001

45900-446-051

X X X X

45900450-010 X X

45900-450-030B

(late availability)

VMU300A1046

X X X X

13 Gas Valve

VK8115V1341

X X X X X X X

VR8615VB1044

X X

V8730C1007

(late availability)

X V8730C1015 X

V8730C1023 X X X

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

Hydronic

Heating/

Combination

Pump

59896343

(UPS15-58FRC)

X X X X X

52722512

(UPS26-99FC)

X X

PL30 X PL36 X X

E12 X

182212-667

(E22)

X X

DHW Pump

E7B X X

E9B X X X X X E12B X X E33B X

127091.1.1 X X X

15 Mixing Chamber

GM20-70-011-01

X X X

GM20-70-020-02

X X X X X X

GM10-20-114

14-5540 X X X

Blocked Flue

Switch

8021205256 X

3-Way Valve

Actuator

VC4011ZZ02/E

X X X X X X X X

FSLF24 X X X X X

3-Way Valve

Body

VCZMR6100/E

X X X X X X X

VCZND6100/U X

VBN3EM3POX

X X

VBN3FP3POX X X X

18 High Limit

TCL085A X TCL110A X

19 ¼ Turn Lock

Wall Hung X

Floor Mount

Wall Mount Back

Panel

14-5402 X X X

14-5402-250 X X

Wall Mount Front

Bottom Wrap

14-5403 X X X

14-5403-250 X X

Front Upper

Wrap

14-5404 X X X

14-5404-250 X X

23 Restrain 14-5405 X X X X X 24 Mounting Bracket 14-5406 X X X X X 25 Lower Bracket 14-5407 X X X X X 26 Wall Top Bracket 14-5408 X X X X X

Support Frame

Assembly

14-5409 X X X

14-5409-250 X X

28 Bracket Front 14-5410 X X X X X 29 Rear Bracket 14-5411 X X X X X

Bezel Stiffener

Plate

14-5412 X X X X X

31 Controller Plate 14-5413 X X X X X 32

Electrical Conduit

Plate

14-5415 X X X

14-5415-250 X X

Electrical Strip

Plate

14-5416 X X X X X

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

34 Plastic Bezel Bezel HS X X X X X 35

Bracket for

Neutralizer Box

14-5419 X X X X X

Air Inlet/ Vent

Adapter

FSA-HEX03 X X X X X X X X X

Plate Heat

Exchanger

(Combination

Models ONLY)

LB31-20X X X X LB31-40X X X X X X X X

LB31-50X X LB31-80X X X

DynaMax HS

Floor Front Panel

14-5501-20-25 X X

14-5501 X X X X X X

DynaMax HS

Floor Base Panel

14-5502 X X X X X

14-5502-60-75 X X X

41 Floor Back Panel

14-5504-20-25 X X

14-5504 X X X

14-5504-60-75 X X X

42 Top Cover Back

14-5505 X X X X X

14-5505-60-75 X X X

43 Side Panel Right

14-5506-20-25 X X

14-5506 X X X

14-5506-60-75 X X X

44 Side Panel Left

14-5507-20-25 X X

14-5507 X X X

14-5507-60-75 X X X

Front Panel

Bottom

14-5508 X X X X X X X X

Side Panel Left

Front

14-5509-20-25

X X

14-5509

X X X X X X

Control Panel

Plate

14-5510 X X X X X X X X

HX Support

Frame

14-5511 X X X X X

14-5511-60-75 X X X

49 Support Plate 14-5512 X X X X X X X X 50 Bracket Right

14-5513-20-25 X X

14-5513 X X X X X X

51 Stand Off Left 14-5514 X X X X X X X X 52 Stand Off Right 14-5515 X X X X X X X X

53 Support Leg

14-5516 X X X X X

14-5516-60-75 X X X

Stiffener under

Leg

14-5517 X X X X X

14-5517-60-75 X X X

Floor Bracket

Left

14-5518-20-25 X X

14-5518 X X X X X X

Floor Rear

Bracket

14-5520-20-25 X X

14-5520 X X X X X X

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

Top Cover

Assembly

14-5521 X X X X X X X X

58 Dashboard

DASHBOARD

X X X X X X X X

Bracket for

Neutralizer Box

14-5525 X X X X X X X X

60 Rubber Bushing 33-0101 X X X X X X X

Condensate Pan

Brace

14-5417 X X X X X

14-5417-250 X X

63 Cover Plate

14-5421 X X X

14-5421-250 X X

64 Standoff 14-5423 X X X X X X 66

Electrical Strip

Plate Protector

14-5420 X

Air Intake

Adapter

44-0008 X X X X X

Plastic Flange

with 3” Street

Elbow

44-0009 X

4” Air Intake Box 14-5551 X X 5” Air Intake Box 14-5546 X

3” Air Intake

Adapter

44-0010 X

4” Air Intake

Adapter

14-5559 X X

5” Air Intake

Adapter

14-5556 X

70 Condensate Pan

14-5418 X X 14-5414 X

14-5414-250 X X

Plate Heat

Exchanger

Bracket

14-5424 X X X

14-5424-200 X X

Transformer

Mounting Plate

14-5541 X X X X X

74 Igniter Gasket GM10-25-018 X 75

Flame Sensor

Gasket

GM10-25-004 X

Burner

Refractory

GM10-25-098-01

X X X X X

GM10-25-107-02

X X X X X

GM10-25-128-02

X X X

Automatic Air

Vent

FV-4M1 X

78 Terminal Board TB-SOLA X 79 On/Off Switch

C6000ALBBXCHLI

40VA

Transformer

HCT-

01E0BB06

81 Inlet Sensor

NTC-

SENSOR-002

Outlet/System

Sensor

50001464-005/B

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

83 Flue Sensor

NTC-

SENSOR-003

84 Outdoor Sensor

NTC-

SENSOR-004

DHW Sensor

(Clip on)

NTC-

SENSOR-001

86 Gas Valve Elbow

45900400-132/B

X X X X X X X

45900400-144/B

X X

Gas Valve Wire

Harness

45900441-015B

X X X

45900429-007B

X X X X X X

88 Relief Valve

10-407-05 X X X X X X X 10-604-10 X X X

89 Wiring Harness

77-0035 X X X X X 77-0036 X X X X X X X X

90 Firing Valve

USA0509101T X X X X X X X

13105 X X 13106 X X X X

DynaMax HS

Fan Discharge

Orifice

14-0377-80 X X 14-0377-100 X 14-0377-250 X X

Expandable Air

Inlet Adapter w/o

Pressure Test

Point

14-0378 X X X X X

Expandable Air

Inlet Adapter

1056-22 X X X X X

94 Flex Pipe

2" Diameter X X X X X X X X X

3" Diameter X

4” Diameter X X

5” Diameter X

Flexible Stainless

Steel Pipe 1" X 11"

66-0075 X

Flexible Stainless

Steel Pipe 1/2" X 11"

66-0073 X

Manual Shutoff

Valve Kit

50002653-001 X

Rear Vent

Adapter

GM10-15-991-01

X X

GM10-15-992-01

X X X

99 Metal Latch

6521-00-0551-YT

X X X X X X X X

100 Strike 7800-02 X X X X X X X X

102

Plastic to

Stainless Steel

Vent Adapter

300566 X X X X X X X 300611 X X X

Stainless to

Plastic Vent

Adapter

FS0604PVCR X

300537 X X

Ref

Name of Part Part ID

DynaMax HS Models

ALL 80 100 150 200 210 250 260 299 399 500 600 700 800

103

Rubber Air

Sleeve

1056-22 X X X X X X X X X 1056-33 X 1056-44 X X 1056-55 X

104 Burner Gasket

GM10-25-074-09

X X X X X X X X X X

GM10-35-078-03

X X X

105

Fan Gasket/

Mixing Chamber

Gasket

33-0036 X X X X X X X 33-0037 X X X X X X X X X 33-0038 X 33-0043 X X X 33-0057 X X X

106 Air Inlet Gasket 33-0069 X X X

107

Current

Transformer

(Combination

Models only)

RIBXRA X

108 Target disk

GM10-25-189-00

109

Washer for

Target disk

GM10-15-014-01

110

Counter sunk

head screw

M4x16 for target

disk

GM10-05-021

111 Vent Gasket

GM10-25-153-00

(Black)

X X X

GM10-25-178-01

(Blue)

X X X

Not shown in Exploded View

Part Recommended spare parts

PART 15 ELECTRICAL DIAGRAMS

15.1 DM 80- 299 INTERNAL WIRING DIAGRAM

15.2 DM 399 – 800 INTERNAL WIRING DIAGRAM

15.2 FIELD WIRING

All wires being placed into the terminal block should be horizontal for at least an inch to ensure sufficient electrical conductivity.

15.2.1 System Sensor

The temperature of the primary return can be controlled by installing a system sensor. The system sensor must be used in all lead lag modes, and must be enabled through the DynaMax HS controller.

15.2.2 Lead Lag Setup

To setup a lead lag system a master boiler must be chosen, and the other boilers connected to it in this system are designated as slaves through sequential Modbus addresses.

Connect the system sensor to the master boiler. The master boiler will use the water temperature in the primary loop to control the operation of the lead lag setup.

If outdoor reset is desired, the outdoor sensor needs to be connected to the Outdoor Sensor location on the DynaMax HS terminal board on boiler 2 (B-2). If the outdoor sensor is not connected to the Master boiler the DynaMax HS Controller will maintain a fixed water temperature that is programmed into the control.

If a remote enable signal is available, it needs to be connected to the Remote Operator terminals on the DynaMax HS terminal board. If the boiler is required to run continuously the switch can be placed in the ‘Local’ position.

15.5 DETAILED CONNECTOR DESCRIPTION

Connector

Pin #

Connector Description

Flame sensor

Igniter ground

Blower tach signal

Blower Vdc power

Blower PWM signal

Blower ground signal

Modbus +

Modbus -

+Vdc Display

Lead Lag, Modbus +

Lead Lag, Modbus -

-Vdc Display

2, 3 DHW Pump, 1/6hp

24Vac or 115Vac for pump contact

5,6 3-way diverter valve

Boiler pump contact

24Vac return

Ground

1 Interlock

2 Gas Valve contact

Blocked Flue

Flow switch

7,8 Alarm, dry contacts

Connector

Pin #

Connector Description

1 24Vac for SOLA 2

24Vac return

Remote enable/disable signal

4,5

Inlet sensor

6,7

4-20mA Input

8,9,10

Outlet sensor, high limit

11, 12

System or Outdoor sensor

1,2 DHW sensor 4,5 Stack sensor

CONDENSING BOILER LIMITED WARRANTY

Camus Hydronics Limited (“Camus”) extends the following LIMITED WARRANTY to the owner of this appliance, provided that the product has been installed and operated in accordance with the Installation Manual provided with the equipment. Camus will furnish a replacement for, or at Camus option repair, any part that within the period specified below, shall fail in normal use and service at its original installation location due to any defect in workmanship, material or design. The repaired or replacement part will be warranted for only the unexpired portion of the original warranty.

THIS LIMITED WARRANTY DOES NOT COVER

1. Failure to properly install, operate or maintain the equipment in accordance with Camus’ manual

2. Abuse, alteration, accident, fire, flood, foundation problems and the like

3. Sediment or lime build-up, freezing, or other conditions causing inadequate water circulation

4. Pitting and erosion caused by high water velocity;

5. Failure of connected systems devices, such as pump or controller

6. Use of non-factory authorized accessories or other components in conjunction with the system;

7. Failing to eliminate air from, or replenish water in, the connected water system

8. Chemical contamination of combustion air or use of chemical additives to water

9. Production of noise, odours, discolouration or rusty water

10. Damage to surroundings or property caused by leakage or malfunction

11. All labour costs associated with the replacement and/or repair of the unit

12. Any failed component of the hydronic system not manufactured as part of the boiler.

HEAT EXCHANGER

If within TWELVE years after initial installation of the appliance, a heat exchanger shall prove upon examination by Camus to be defective in material, thermal shock, leakage or workmanship, Camus will exchange or repair such part or portion on the following pro rated limited warranty

Years into Warranty % of List Price

8 30

9 40 10 50 11 60 12 70

This term is reduced to SIX years if the appliance is used for other than hydronic space heating. Heat Exchanger shall be warranted for (20) years from date of installation against “Thermal Shock” (excluded, however, if caused by appliance operation at large changes exceeding 150ºF between the water temperature at inlet and appliance temperature or operating at temperatures exceeding 210oF).

BURNER

If within FIVE years after initial installation of the appliance a burner shall prove upon examination by Camus to be defective in material or workmanship, Camus will exchange or repair such part or portion.

ANY OTHER PART

If any other part fails within one (1) year after installation, or eighteen (18) months from date of factory shipment based on

Camus' records, whichever comes first. Camus will furnish a replacement or repair that part. Replacement parts will be shipped f.o.b. our factory.

DURATION OF LIMITED WARRANTY

Any limited warranty, including the warranty of merchantability imposed on the sale of the boiler under the laws of the state or province of sale are limited in duration to one year from date of original installation.

STATE LAW & LIMITED WARRANTY

Some states or provinces do not allow:

a) Limitations on how long an implied warranty lasts b) Limitations on incidental or consequential damages. The listed limitations may or may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state and province to province.

CONDITIONS

We will not:

a) Repair or replace any boiler, or part, subject to

conditions outlined in ‘This Limited Warranty Does Not Cover’

b) Reimburse any costs associated with repair and/or

replacement

c) Replace and/or repair any boiler without complete model

number/serial number

d) Replace any boiler without prior receipt of actual rating

plate from the appliance.

HOW TO MAKE A CLAIM

Any claim under this warranty shall be made directly to Camus Hydronics Limited Canadian Head Office

SERVICE LABOR RESPONSIBILITY

Camus shall not be responsible for any labour expenses to service, repair or replace the components supplied. Such costs are the responsibility of the owner.

DISCLAIMERS

Camus shall not be responsible for any water damage. Provisions should be made that in the event of a water/appliance or fitting leak, the resulting flow of water will not cause damage to its surroundings.

Name of Owner

Name of Dealer

Address

Model No.

Serial #:

Date of Installation:

Date of Initial Operation:

6226 Netherhart Road, Mississauga, Ontario, L5T 1B7, CANADA

CAMUS Hydronics is a

manufacturer of replacement parts for most copper finned

The CAMUS

CERTIFIED! Seal assures you that Reliability, Efficiency & serviceability are built

water heaters

and heating boilers as well as a

into every

single unit! For more information

supplier of specialty

HVAC products. Our service line is open 24 hours, 7 days a week!

on our innovative

products from CAMUS Hydronics Limited, call 905-696-7800 today.

CAMUS HYDRONICS LTD.

6226 Netherhart Road, Mississauga, Ontario L5T 1B7

TEL: 905·696·7800 FAX: 905·696·8801

Camus Hydronics DMH-261, DMH-291, DMH-391, DMH-501, DMH-601 Installation, Operation And Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual