camry EK-9 Series Instructions For Use Manual

05EK-016E R1

g

1.

2.

76

EK-9 SERIES

1. When setting time span, touch "T-SET" to confirm and prompt to next digit. After

setting time span, touch "T-SET" to start counting down. During counting down,

touch "T-SET" to clear the set time span.

2. The timer counts down to "00:00", alarm will start "beeping" for 60 times and

switch off automatically

3. Touch any key to stop "beeping".

4. Max. time span of the alarm timer: 99:59.

scale

will

TO SET ALARM TIMER

WARNING INDICATORS

1. Replace new battery.

2. Scale overload. Remove item to avoid damage.

Max.Weight capacity is indicated on the scale.

CLEANING AND CARE

1. Clean the scale with a slightly damp cloth. DO NOT immerse the scale in water

or use chemical/abrasive cleaning agents.

2. All plastic parts sho uld be cleaned immed iately after contact with fats, spices,

vinegar and strongly flavored/colored foods. Avoid contact with acids citrus juices.

3. Always use the scale on a hard, flat surface. DO NOT use on carpet.

TEMPERATURE SENSOR

o

1. Temperature range: 0~+40C

o

2. Division: 0.5 C

Condition 2: "TARE" function

When LCD reading is >1g,

LCD will show “-----” or “0g” each time “ is touched.

“-----” means not stable, please wait for a moment. “0g”

and meanwhile an icon “TARE” on upper left corner of

LCD mean “TARE” function is active. Max. capacity is

reduced by total weight of all loads.

Z/T”

Electronic Kitchen Scale with Touch Button

INSTRUCTIONS FOR USE

Temperat ure
displa y

Auto shut-off occurs if display shows
'0' or show s the sam e weight reading
for 2 minutes.

AUTO SHUT OFF

MANUAL SHUT OFF

To maximize battery life,
"ON/OF F" again to turn off the scale
after using.

always touch

Touch "ON/OFF"

to switch on

Touch "T-SET " to star t

count dow n

Touch

"T-SET”

Touch

"T-SET”

Touch T-SE T

to beg in ala rm
tim er se tt in g

" "

Touch

"T-SET”

Setting 1st binary digit
for minutes

Setting 2nd binary digit
for minutes

Setting 1st binary digit
for seconds

Setting 2nd binary digit
for seconds

ISO 90 01:20 00 CERT IFIED B Y S

GS

5

g

Water

ml

Milk

ml

Water

Milk

kg

kg

fl'oz

fl'oz

lb:oz

lb:oz

If the scale is with both measuring system of Metric (g,kg) and Imperial (oz,lb), you can

"UNIT" to convert between two systems during the course of weighing:

. "UNIT" for 3 seconds to convert weight unit between Metric and Imperial systems.

touch

1 Touch

2 Touch. "UNIT" shortly to convert between weight display and volume (water or milk) display.

"UNIT"

for 3

seconds

Touch

Metric
system:

Imperial
system:

TO CONVERT WEIGHT UNIT

"ZERO" OR "TARE" FUNCTION

Condition 1: "ZERO" function
When LCD reading is negative value or 1g,

LCD will show “-----” or “0g” each time “ is touched.
“-----” means not stable, please wait for a moment. “0g”
and meanwhile an icon “0” on lower left corner of LCD
mean “ZERO” function is active. Max. capacity remains
unchanged.

Z/T”

To weigh different loads consecutively without removing loads from the scale.Put first

next load. You can repeat this operation.

Load on

the scale, get weight reading. button to reset the LCD reading to "0" before adding Touch"T/Z"

UNIT"
shortly

Touch

"

UNIT"
shortly

Touch

"

"UNIT" shortly Touch

UNIT"
shortly

Touch

"

UNIT"
shortly

Touch

"

"UNIT" shortly Touch

C

R2

032

TO REPLACE BATTERY

1. Open battery case cover on the back of scale.

2. Bend the small contact outwards and the battery will come out.

3. Install new battery by putting one side of battery beneath the

black tab and then pressin g dow n the other side until the

battery is locked.

4. Close the battery case cover.

BATTERY

2x3V lithium cells. Please remove isolation sheet

before use.

black tab

contact

Alarm timer setting

Down / Unit conversion

Up / Zero or tare

Switch

TOUCH BUTTONS ILLUSTRATION

Wa ter

ml

Mi lk

kg

fl 'oz

lb :oz

1

FEATURES AND SPECIFICATIONS

1.With touch button

2.With high precision strain gauge sensor

3.Two unit systems g(kg)、lb:oz convertible

4.Indicate volume of water and milk

5.With alarm timer

6.With room thermometer

7.With zero/tare function

8.Low battery power/Overload indication

LCD display area

Effective weighing area

Battery case cover

* Please always put weighing object within effective weighing area.

PRODUCT OUTLINE

LCD DISPLAY

Timer

Alarm

Tare

Negative Value

Zero

Water volume indicator

Milk volume indicator

Room temperature

Temperature unit

Weight unit

Volume unit

Touch buttons

32

g

Wate r

ml ml

Milk

Weigh t mode

Milk vo lume mo deWater vo lume mo de

WOR KING M ODES

A.Place the scale on a soild and flat

surface.

B.Press “ON/OFF” to turn on the

scale.

C.Wait until LCD shows “0”, and

press UNIT button to choose

“water” or “milk” mode.

D.Put a liquid container onto the

scale platform.

E.Press Z/T button to reset LCD

to “0”.

F.Pour liquid (water or milk) into the

container, LCD shows the volume

of the liquid.

G.Press UNIT button to choose

“weight” mode and view the weight

of liquid.

A.Place the scale on a solid and flat
surfase.
B.Place bowl (if used) on the scale
before turning on the scale.
C.Press “ON/OFF” to enter weighing
mode.
D.Wait until LCD shows all information.
E.Load weighing object on to start
weighing,LCD will show the weight
reading.
F.If the weighing object is water or
milk,press UNIT button to choose
volume mode and view the volume
of weighing object.

Wate r

ml

Wate r

ml

Wate r

ml

Wate r

ml

Wate r

ml

TO START WEIGHING

4