Campomatic TL10E User Manual

Download

Page 1

tl10e

Full Automatic Washer

INSTRUCTION MANUAL

Made in China

WWW.CAMPOMATIC.COM

Page 2

Notes

Safe ty and pr ecaut ions. ..... ..... ................. ..... ..... ..... ..... ................. ..... ..

Inst allat ion of th e washe r..... ..... ...................... ..... ..... ..... ................. ..... .

Prep arati on befo re wash ing.. ..... ..... ................. ..... ..... ..... ..... .................

Part s ident ifica tion of t he wash er.... ..... ................. ..... ..... ..... ..... .............

Inst ructi on of the w asher o perat ion pan el... ...................... ..... ..... ..... .......

Quic k start ..... ..... ..... ................. ..... ..... ..... ..... ................. ..... ..... ..... ..... .

The main w ash.. ..... ..... ..... ................. ..... ..... ..... ..... ................. ..... ..... ...

Spec ial fea tures ..... ..... ..... ................. ..... ..... ..... ..... ................. ..... ..... ...

About the proc edure o f full au tomat ic wash p rogra m.... ................. ..... ..... ...

Clea ning an d Maint enanc e of the wa shing m achin e.... ...................... ..... ..... ..... .....

Identify usual trouble of washer..............................................................................

Malf uncti on disp lay and s oluti ons.. ..... ...................... ..... ..... ..... ..............

Techni cal spe cific ation s.... ..... ..... ................. ..... ..... ..... ................. ..... ..... ..... ..

Page 3

Safety and precautions

Observe the following items in order to prevent from injuring yourself, others and the damage of property:

！

Warning

！！

Caution

Please observe following contents of graphics.

This graphics represents［cause attention］,and detailed cautions will be displayed inside the graphics.

This graphics represents［operation prohibited], and detailed prohibitive items will be displayed inside the graphics.

This graphic represents [forcible execution], and detailed forcible

execution items will be displayed inside the graphics.

This indicates serious injury or death to human being may be caused.

This will remind you that injury to people and damage to property may occur.

！

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or knowledge, unless they have been given supervision use of the appliance by a person responsible for their safety. should be supervised to ensure that they do not play with the appliance.

！

Please do not disassembly and assembly the machine without authorization.

No dismantling

Please do not install the machine in damp and raining environment to avoid electric shocking, catching fire, faults and distortion accidents.

小天鹅

lack

or instruction concerning

Warning

Please do not insert your hand and take out clothes inside the spin barrel before it is fully stopped.

No touching

Please do not directly rinse the machine with water when cleaning.

of experience and

Children

小天鹅

No dampness

No rinsing

Page 4

！

Warning

Please do not let children climb the machine or peer into the rotating spin barrel to avoid accidents.

Prohibited

Please do not damage power flexible cord and power plug to avoid electric shocking, short circuit and catching fire.

Prohibited

Please pull out plug from the socket if the machine is not in use.

It is prohibited to wash the clothes touching with kerosene, gasoline, alcohol and other flammable materials.

Prohibited

Regularly clean the power plug to remove dust and dirt to avoid contact failure.

Please well connect the earth line of socket to avoid electric shocking by accidental leakage.

（earthing）

Pull out the plug

Please insert the power plug tightly.

Earthing

Please do not place on the washer burning candle, mosquito-repellent incense, cigarette and other flammable things, as well as electric stove, air heating fan and other heating sources.

Smoke and fire prohibited

小天鹅

Page 5

Please use correct power source.

Please do not pull out or insert the plug with wet hands to avoid electric shocking.

！

Please ensure that the water inlet pipe is connected and the tap is opened before washing clothes.

Customers are not allowed to change the power line without permission.

Wet hands are prohibited

Caution

The water temperature shall not exceed 50℃ when washing with warm water.

Prohibited

It is strictly prohibited to place children or lay weights on the washer.

>50 C

小天鹅

Prohibited

Please do not pull the electric cord when pulling out the plug.

Prohibited

Please do not wash down jacket, raincoat, fishing coat and similar clothes in the washer.

Prohibited

Page 6

Installation of the washer

Remove package

Remove package and take out the bottom board of the cabinet on the foam cover. Open the lid of washer's door and take out accessories. A trial operation or washing on the foamed cushion is strictly forbidden.

Installation of drain hose

Completely sleeve the drain

hose over the sewer.

Fix and tighten it with a hoop.

( As shown in the figure )

Placement of water drain hose

Under3m

If the water drain hose shall be extended, its length shall not exceed 3 meters, otherwise it will affect the water discharging time.

The placed height of water drain hose shall not exceed 15cm.

FOR LOWER DRAIN SYSTEM ONLY

Base foamed cushion

Under 15cm

Do not bend the water drain hose and place it under the washer.

Placement of upper water drain hose

The he ig ht o f dr ain hose (“a”)s ho ul d between 86-100 cm . Diam et er o f “b ”shuld not less t ha n 3 cm , an d flow capacity not le ss t ha n 40 L /Min.

Befo re w as hi ng machine star ts , us er s hould hang up the drai n pi pe 8 6- 100cm height fr om t he f loor.

FOR UPPE R DR AI N SYSTEM ONLY

Installation of water inlet pipe

Put the water inlet pipe(which has

metallic filtering bag) screw on to the tap. Tightly screw another end of water inlet hose on water inlet valve . (with rubber seal ring inside).

Note: When tightening the clamping nut, evenly apply the force and do not twist the water inlet valve to avoid breaking of water inlet valve joint.

Only for model with double screw thread water inlet pipe

Clamping nut

86~100 cm

Water inlet hose

Page 7

Installation of the washer

Installation of water inlet pipe

Small ball

Push down the slide jacket to expose the small balls and enable separation of connector socket from speedy connector.

5mm

Junk ring

The connection socket consists of A and B two parts. Before installation, A and B two parts must be unscrewed about 5mm, or directly disconnected. If the bore of water tap is larger, remove the plastic junk ring of

Connect

part A.

Connect: Push down the slide jacket of speedy connector ( 4 small balls must be exposed ), insert it into the connection

socket and then push upward Rel ease the c onnec tion of water tap with speedy connector

completely.If it is required to feed water, simply open the water tap. Separate: Close the water tap, push down the slide jacket of speedy connector and pull out the speedy connector.

Unscrew four screws of part A and sleeve part A horizontally

over the mouth at the end of water tap (the mouth at the end

of water tap must be flat and smooth. Flatten it by filing if it is not flat) and push it upward with force making the rubber washer firmly press the plane center of water tap mouth. Then tighten the screw sequentially. After that, tightly screw on part B.

Separate

Tightly screw another end of water inlet hose on water inlet valve . (with rubber seal ring inside). Note: When tightening the clamping nut, evenly apply the force and do not twist the water inlet valve to avoid breaking of water inlet valve joint.

Only for model with single screw thread water inlet pipe

！

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The instructions for appliances connected to the water mains by detachable hosesets shall state that the new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.

Clamping nut

Water inlet hose

Page 8

Preparation before washing

Adjust the adjustable foot to make

the washer be placed stable.

Adjustable foot (extend when clockwise rotating and shorten

when counterclockwise rotating) (Slightly incline the washer first and loosen the adjustable foot knob. Adjust the adjustable foot so as to ensure four corners of washer be steadily contacted with the ground. Then tighten the adjustable foot knob and lock it. If the ground is obviously not flat, correction should be made on the ground surface, otherwise the washer barrel will incline and knock the cabinet)

Connect with to

power source.

Put down the drain

house.

Gravity drain

Install the water

inlet hose.

For one inlet hose

For two inlet hoses

+++

Put in clothes and suitable amount of washing powder.

Turn on the

water supply.

NOTICE

！

Upper drain

Note: The water will overflow when the height of the drain hose under 860mm.

Before washing, please do take out coins, keys and other hard goods, and zip up clothes

tightly to prevent them

barrel from damage.

and

>860mm

Page 9

Parts identification of the washer

(For upper drain only )

Upper drain hose

Top lid

Contr ol p anel

Fixing ring (1) is used for the fixing in time of the installation of the lower drain hose.

Accessories

Universal connector

frame

Cabin et

Drain h os e

(For lo we r drain o nl y)

Adjus ta ble leg

Adjustable foot knob

Self-tapping screw

Only for lower drain hose

Water inlet hose assembly

Onl y for mod el with s ingle scr ew thre ad wate r inlet p ipe

Water inlet hose assembly

Onl y for mod el with d ouble scr ew thre ad wate r inlet p ipe

Please refer to the real material as the attachment

Base cover

Onl y for mod els inc ludin g base co ver

Page 10

Instruction of the washer operation panel

Was h lev el

1 2

Wash

Press the button to select

the washing time.

Rinse

Press the button to select the time of

rinse.

Spin

Press the button to select the time of spin.

If the draw in g is c ha nged, no info rm at io n anymore .

To p

otec

e c

t th

ont

el, t

l pan

e inte

！

al ti

e of p

er o

nd off shoul

n a

d be n

ot less tha

n 30 s

Press the "water level" and " Spin" at the same ti me to lock buttons on control pa nel.

Press th e "water level"an d "Spin" at the same ti me again to unlock buttons.

econds.

Page 11

Hot

War m

Col d

Page 12

Quick start

1 Install the washing

machine

2 Load the laundry

3 measure out the

detergent

4 Close the

machine door

9 Press the

[start/pause] key

8 Select the desired

programme

7 Plug the power supply

6 Turn on water supply

5 Put down (hang up)

the drain pipe

Programme selection

Press the POWER button.

Select the proper water level and other attached functions.

press the start/pause key.

The wash stops

When the wash stops, the buzzer will buzz continuously for 6 times and

then the power will be automatically cut off.

Turn off the water tap.

Although the power can be cut off automatically, the power plug must be pull out for the safety.

Page 13

The main wash

Instruction of the NORMAL program

1.[Normal] wash program is the easiest, most convenient and most common washing program. When the user press the power switch and then press [Start/Pause] button, the normal washing program will start to work.

2.When the washer start to work, the digital tube show the remain time. The indicator light which stand for remaining time is flickering.

Steps in details

1.Press the power switch.

2.According to the washing amount choose the proper water level.

3.Press START/PAUSE button.

Instruction to single wash procedure

1.User may freely select any single procedure, or any combination of procedures among WASH, RINSE and SPIN according to the actual requirements. It is only required to turn off any one or two of these three indicators that not needed by the user. And keep the indicator be on showing the process needed by the user.

2.Single wash -- after switching on the power, turn off RINSE and SPIN two indicators by pressing these two keys. The operation for single rinse and single spin is similar.

3.Single wash-spin – after switching on the power, turn off RINSE indicator by pressing that key. The operation for single rinse-spin and single wash-rinse is similar.

Use the cleaning solution for twice

1. Put the laundry in the first batch and wash powder and press “Function” button to set single “wash” to run.

2. Take out the laundry in the first batch after hearing the buzzing sound.

3. put in the laundry in the second batch, and run “ Wash”, “Rinse”, “Spin”.

4. Take out the laundry in the second batch after hearing the buzzing sound.

5. Put in the laundry in the first batch and press “ Function” button to run “Rinse” and “Spin”.

！

NOTICE

1.Close the lid of the door when machine is running, otherwise, it will automatically stop working during spin process and send out abnormal warning.

2.The washer will not work when the filled water does not reach the set water level.

3.The selection of rinse water level: the level is equal to wash water level. Press [Rinse Level] button, the indicator light which stand for rinse level flickered. User can select the rinse water level according to needs. Rinse level exceed that wash level all the time. It shows the wash level if not press this button. And only show rinse level when rinseing.

4.After pressing down [ Power Switch ], if the [Start / Pause ] button is not pressed, the power will be automatically cut off in 10 minutes.

Page 14

Special features

Delay time program

Delay time means the preset beginning time of washing.

1.Switch on the power .

2.Open the tap and lay the drain hose.

3.Put in the laundry and detergent.

4.Select the propre water level according

to the quantity of clothes.

5.Select the functions and programs.

6.Press “DELAY” button to select the

beginning time of washing.

7.close the lid and press “START/PAUSE” button

Confirmation of the delay and inspection

1. After the delay function is started, the corresponding delay light will flash, and other lights are turned off.

2. After the delay function is started , press “ Delay” button continuously , you may inspect the preset program and function . Loose the button , the program return to delay status.

Cancel the delay time, or alternate the delay time

1. Press “ Power” button to cancel the delay time.

2. To change the delay time , cancel the delay time first , and then press “Delay” button to reset.

Press t he “ DELAY” b utton e ach time, the number o n the d igital i ndication adds b y “1” ; After the n umber reaches “ 24”,press t he “ DELAY”button each t ime , the number a dds b y “6” ; After t he number reaches 4 8, the l ight of delay t ime is t urned off , a nd the delay p rogram return to original status.

Quick

Wash time is short. Suitable to wash light stained clothes and clothes in summer.

Air dry

As for not easily fading,deforming , and non-waterproof clothes , can use the function to dry clothes without heating, and to reach the result of being dried in a room.

Anti-wrinkle

The wash time is short,rinses many time with high water level,thoroughly wash away the garment.

Page 15

Special features

Page 16

About the procedure of full automatic wash program

15 16

Page 17

Cleaning and Maintenance of the washing machine

End of program

The washin g machi ne will send off the sound

" "

of dou-dou at the end of any program operation to remind you to take out the laundry or operate it again. Aft er the sound ,the washing m achine ret urns to its power-off state with no display and all lights off. Please shut off the tap, pull out the plug when not in use to avoid water leakage or the fire accidents.

Clean the water inlet

After long time use, the water inlet mesh bag may be blocked with smudginess, and should be cleaned according to the following steps:

1. Switch on the power, followed by shutting off the tap .

2. Let the washer works for 5 seconds so that water flows into the tub through the water inlet hose. then turn off the power.

3. Unload the water inlet hose and clean the mesh bag, then restore the water inlet assembly.

Maintenance

Use gentle clothing to wipe off the water and dirt on the surface each time after using the washing machine. Detergent , prope llant and oth er c hem icals a re n ot allowed to use so as to avoid any damage to the pla stic accessories.

Clean Of the filter

After using the washing machine for a period, please clean it according to the following steps:

1. Take out the lint filter.

2.Open the filter and wash it clean in the water.

3. Restore it and fix it.

(only for magic filter)

After using the washing machine for a period, clean it according to the following steps:

1. Take off the lint filter.

2. Turn over the mesh bag and wash it clean in the water.

3. Restore and fix it.

(only for normal filter)

Clean the lint filter in the drain pump (only for having drain filter)

1. Drain the water ou t of the pump,under whic h use a container to coll ect.

4. Clean the filter.

2. Loosen the pump co ver anticlockwise .

5. Restore it and adj ust the convex place to ali gn at the pump hole.

3. Take out the l int filter.

6. Tighten the pump cov er clockwise.

Notes:

If the drain filter is not cleaned at proper time (every 10 times of use),Drain problem could be caused.

Page 18

Identify usual trouble of washer

When the washer is in trouble, please contact local service office or the sales service department of our company and the customer should not dismantle the machine without permission. If the washer can not work normally, or appear abnormity or alarms, please check and correct as follows.

List of faults and inspection

Faults

No water flows in

No washing

Abnormal draining

Inspection Items

If the power is off or the fuse is burned out. If the water supply is cut off or the water pressure is too low. If the inlet hose is properly connected and the water tap is opened. If the filtering screen of inlet valve is blocked by dirt. If the coil of inlet valve is damaged. (The slight electromagnetic sound is normal phenomenon when the inlet valve is switched on) If the "Start / Pause" button is pressed after the power switch is pressed.

If the power is off or the fuse is burned out. If the power supply voltage is too low. If the water amount reaches to the required water level. (The washer will not work if the water amount does not reach the required water level) If it is set to "Delay" washing mode. (It will only start to work until the reservation time reached)

If the water drain hose is placed very high. If the end of water drain hose is sealed in pond. If the internal rubber ring of drain valve is blocked by dirt.

If the door lid is closed.

Abnormal spin

If all clothing piled largely at one side of barrel or the clothing is excessively placed. If the washer is not placed in stable condition or it is placed in inclination state. (The ground is not flat). If the motor belt is loosened.

Note: During the de spin process, if washing are piled at one side of the spin barrel, it will cause unbalance of spin barrel resulting in striking. At this moment, the computer inside the washer will feel this unbalance phenomenon and will automatically correct it ( fill in water Washing ). However, if unbalance situation is not removed after continuous three corrections, which means the computer auto-correction can not resolve the problem. Then the user has to manually and evenly place the clothing inside the barrel to solve the problem.

Page 19

Malfunction display and solutions

When the washer is in trouble, please contact local service office or the sales service department of our company and the customer should not dismantle the machine without permission. If the washer can not work normally, and the abnormal indication is shown in the nixie tube window or the machine alarms, please check and correct them as follows.

Alarm for water drain time out.

Page 20