Page 1
RC20BL
Wet & Dry
Dual Purpose Vacuum Cleaner
INSTRUCTION MANUAL
:
Made in China
WWW.CAMPOMATIC.COM
Page 2
Characteristic
Dry & Wet Dual Purpose
1400W Strong Suction
Cord Retractable
Safety Protection Device to ensure normal work of the motor
Base with jack to store accessories easily
RC20BL
Blowing function to satisfy deferent people’s requirement
Name of Parts
ENG
2
Page 3
RC20BL
You can choose suitable accessories for different condition.
Floor Brush
Press down the side of bristle button with mark “
use the bristle extended for hard floor. Press down the side of
bristle button with mark “━”and then use the bristle retracted
for hard floor.
Absorbing Brush
For clean the water on the hard floor or the carpet.
Triangle Brush
For cleaning bookshelf, windows, desktop etc.
”and then
ENG
Crevice Tool
For cleaning corner edge and draws etc where is difficult to clean.
Blowing Door
3
Page 4
RC20BL
For blowing the dust in the gap.
Warning
1. Read this instruction booklet carefully.
2. This appliance is for domestic use only. Use as described in this
instruction booklet.
3. Before using the appliance, check if the mains power voltage
corresponds to the voltage shown on the rating plate.
4. It is class Ⅱ electric appliance, so it need not be earthed.
5. Do not use it in the flammable and explosive place.（Fig1）
6. Do not block the flow of
damage the motor. (Fig2)
Fig1 Fig2
7. Do not use the appliance to vacuum all the latter things:
lighted stub ,hot ashes and other combustible things (Fig3)
Fig3 Fig4
air. Blocking the air suction or exit may
those matter due to oil (Fig4)
sharp matter (Fig5)
Fig5 Fig6
ENG
4
Page 5
RC20BL
those tiny powder like power of lime, land plaster etc. They may
block the filter bag and the flow of air. It may damage the mot or.
(Fig6)
those things that can produce lather like washing powder, cleanser
etc. There may be some bubble blowing from the air exit. Please dry
it first and then restart it.
8. Do not turn over the vacuum cleaner. Otherwise the water may enter
the motor to damage it.（Fig7）
Do not use the appliance as a lift pump.
We suggest you do not use it as a producer’s equipment.
Fig7 Fig8
9. Always remove the plug from the power socket when the appliance is
not in use and before carrying out any cleaning or maintenance
operations.
10. Keep the vacuum cleaner away from direct irradiation sunshine and
the place with high temperature. Heat can deform and discolor the
plastic parts of unit. (Fig8)
11. Check the h
damaged. (Fig9)
ose periodically. Replace it in time if there is any way
Fig9 Fig10
12. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarity qualified person in
order to avoid a hazard. (Fig10)
ENG
5
Page 6
RC20BL
How to use
1. Ready for use
Connection
Insert the flexible tube into the air intake duct. To do this, slide intake
duct cover insert the tube and press until it clicks into position. (Fig11)
To remove it, press down the button and pull out the hose. (Fig12)
Fig11 Fig12
To use the blowing function, just need plug the hose into blowing door.
Connect the flexible tube, extensive tube and accessories correctly.
ENG
6
Page 7
RC20BL
2. Switch on the appliance
Before use please check the filter bag is installed. Do not work with no
filter back.
1. While pressing down the cable winding button with one hand, draw out
the cable. When you find the yellow sign, please draw it slowly. If you
find the red sign please stop drawing. Insert the plug into the power
socket. If you need retract the cable, just press down the cable winding
button. (Fig13)
2. Press the ON/OFF button
Fig13 Fig14
Change the air power control knob on handle can adjust the suction. The
greater air door the smaller suction.
to switch the appliance on. (Fig14)
Safety Device
When there is full of water in the dust barrel(about 16L), the float
will be risen and the appliance will stop working. In addition you can
hear abnormal sound. The power supply hasn’t been cut off yet at that
time. So cut off the power supply immediately. And spill the water in
the barrel. Restart the machine.
When the vacuum is overturned, the float will risen. In that case cut
off the power supply and upturn the vacuum.
If you run the vacuum or leave it alone while the float is risen, it may
damage the motor and lead to fire.
ENG
7
Page 8
RC20BL
Maintenance
1. Clean the dust barrel
When finishing cleaning or the suction decreased obviously, cut off the
power supply and empty the barrel in time.
Refer to the following steps:
(1) Release the lock button and lift the top cover. (Fig15)
(2) Before remove the fi
shake it about 20 times up and down. (Fig16)
Fig15 Fig16
(3) Remove the filter bag and clean the dust in the barrel. (Fig17)
4) Replace the bag and the top cover. (Fig18)
(
Fig17 Fig18
If you do not empty the barrel in time, the dust in the barrel will emit
smell. So please clean the barrel periodically. Before use again dry it.
2. Clean the filter
If the filter bag is blocked badly, clean it with water. If you need you can
use some neutrality cleanser.
(1) Remove the filter bag.
(2) Clean it (Fig19)
(3) Dry it (Fig20)
dry it replace it according to primary steps.
After
Do not use boiled water to clean it or dry it wit fire.
3. Clean the vacuum cleaner and the accessories
ENG
8
Page 9
RC20BL
Fig19 Fig20
Clean the accessories and vacuum with soft cloth dipping water or
neutrality cleanser. (Fig21)
(1) Do not clean the body of vacuum cleaner in petrol or oil-like
liquid. Please wipe it with water or neutral detergent.
(2)When you wipe the appliance please dry the soft cloth by
screwing.
Remove the sundries adhering to the floor brush with old
toothbrush every month. (Fig22)
Fig21 Fig22
Troubleshooting
Trouble Check Part Resolve
Motor doesn’t
work
Power Plug If it doesn’t plug in, plug in.
Hose
If hose is blocked, clean it. If straight tube
doesn’t connect well, connect it well.
Suction decrease
Hose comes away
from the seat
Dust Barrel If there is full of dust or water, empty it.
Filter Bag If it is blocked, clean it.
Hose
Connection
Plug the hose into the seat.
9
Page 10
Technique parameter
Model No. Power Voltage Frequency
XXXX 1400W 220-240V～ 50/60Hz
Circuit diagram
RC20BL
ENG
10
Page 11
RC20BL
ً
ً
•
ً
ً ً
ً
.
•
•
•
11
AR
Page 12
RC20BL
ً
U
12
ً
AR
Page 13
RC20BL
U
ً
13
AR
Page 14
RC20BL
8-
91011-
ً ً
ً
1213-
Fig7 Fig8
Fig9 Fig10
14
AR
Page 15
RC20BL
U
1234-II
567-
Fig1 Fig2
Fig3 Fig4
Fig5 Fig6
15
AR
Page 16
RC20BL
U
U
ً
–
U
U
.
16
AR
Page 17
RC20BL
RC20BL
220-240~ 50-60Hz1400W
:
U
17
AR
Page 18
RC20BL
ﺥﺎﺳﻭﻻﺍﻭ ءﺎﻤﻠﻟ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺔﺴﻨﻜﻣ
Campomac S.R.L. Via Configliachi 5/B . 35031, Abano Terme (Padova), ITALIA
WWW.CAMPOMATIC.COM
Loading...