INSTRUCTION MANUAL
CSIM11 pH and ORP Probes
Copyright © 2000- 2014
Campbell Scientific, Inc.
Revision: 7/14
Limited Warranty
“Products manufactured by CSI are warranted by CSI to be free from defects in
materials and workmanship under normal use and service for twelve months
from the date of shipment unless otherwise specified in the corresponding
product manual. (Product manuals are available for review online at
www.campbellsci.com.) Products not manufactured by CSI, but that are resold
by CSI, are warranted only to the limits extended by the original manufacturer.
Batteries, fine-wire thermocouples, desiccant, and other consumables have no
warranty. CSI’s obligation under this warranty is limited to repairing or
replacing (at CSI’s option) defective Products, which shall be the sole and
exclusive remedy under this warranty. The Customer assumes all costs of
removing, reinstalling, and shipping defective Products to CSI. CSI will return
such Products by surface carrier prepaid within the continental United States of
America. To all other locations, CSI will return such Products best way CIP
(port of entry) per Incoterms ® 2010. This warranty shall not apply to any
Products which have been subjected to modification, misuse, neglect, improper
service, accidents of nature, or shipping damage. This warranty is in lieu of all
other warranties, expressed or implied. The warranty for installation services
performed by CSI such as programming to customer specifications, electrical
connections to Products manufactured by CSI, and Product specific training, is
part of CSI's product warranty. CSI EXPRESSLY DISCLAIMS AND
EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. CSI hereby disclaims,
to the fullest extent allowed by applicable law, any and all warranties and
conditions with respect to the Products, whether express, implied or
statutory, other than those expressly provided herein.”
Assistance
Products may not be returned without prior authorization. The following
contact information is for US and international customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle
repairs for customers within their territories. Please visit
www.campbellsci.com to determine which Campbell Scientific company serves
your country.
To obtain a Returned Materials Authorization (RMA), contact CAMPBELL
SCIENTIFIC, INC., phone (435) 227-9000. After an application engineer
determines the nature of the problem, an RMA number will be issued. Please
write this number clearly on the outside of the shipping container. Campbell
Scientific’s shipping address is:
CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784
For all returns, the customer must fill out a “Statement of Product Cleanliness
and Decontamination” form and comply with the requirements specified in it.
The form is available from our web site at www.campbellsci.com/repair. A
completed form must be either emailed to repair@campbellsci.com or faxed to
(435) 227-9106. Campbell Scientific is unable to process any returns until we
receive this form. If the form is not received within three days of product
receipt or is incomplete, the product will be returned to the customer at the
customer’s expense. Campbell Scientific reserves the right to refuse service on
products that were exposed to contaminants that may cause health or safety
concerns for our employees.
Precautions
DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND
TRIPODS, TOWERS, AND ANY ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES,
ANTENNAS, ETC. FAILURE TO PROPERLY AND COMPLETELY ASSEMBLE, INSTALL, OPERATE, USE, AND MAINTAIN TRIPODS,
TOWERS, AND ATTACHMENTS, AND FAILURE TO HEED WARNINGS, INCREASES THE RISK OF DEATH, ACCIDENT, SERIOUS
INJURY, PROPERTY DAMAGE, AND PRODUCT FAILURE. TAKE ALL REASONABLE PRECAUTIONS TO AVOID THESE HAZARDS.
CHECK WITH YOUR ORGANIZATION'S SAFETY COORDINATOR (OR POLICY) FOR PROCEDURES AND REQUIRED PROTECTIVE
EQUIPMENT PRIOR TO PERFORMING ANY WORK.
Use tripods, towers, and attachments to tripods and towers only for purposes for which they are designed. Do not exceed design
limits. Be familiar and comply with all instructions provided in product manuals. Manuals are available at www.campbellsci.com or
by telephoning (435) 227-9000 (USA). You are responsible for conformance with governing codes and regulations, including safety
regulations, and the integrity and location of structures or land to which towers, tripods, and any attachments are attached. Installation
sites should be evaluated and approved by a qualified engineer. If questions or concerns arise regarding installation, use, or
maintenance of tripods, towers, attachments, or electrical connections, consult with a licensed and qualified engineer or electrician.
General
• Prior to performing site or installation work, obtain required approvals and permits. Comply
with all governing structure-height regulations, such as those of the FAA in the USA.
• Use only qualified personnel for installation, use, and maintenance of tripods and towers, and
any attachments to tripods and towers. The use of licensed and qualified contractors is highly
recommended.
• Read all applicable instructions carefully and understand procedures thoroughly before
beginning work.
• Wear a hardhat and eye protection, and take other appropriate safety precautions while
working on or around tripods and towers.
• Do not climb tripods or towers at any time, and prohibit climbing by other persons. Take
reasonable precautions to secure tripod and tower sites from trespassers.
• Use only manufacturer recommended parts, materials, and tools.
Utility and Electrical
• You can be killed or sustain serious bodily injury if the tripod, tower, or attachments you are
installing, constructing, using, or maintaining, or a tool, stake, or anchor, come in contact with
overhead or underground utility lines.
• Maintain a distance of at least one-and-one-half times structure height, 20 feet, or the distance
required by applicable law, whichever is greater, between overhead utility lines and the
structure (tripod, tower, attachments, or tools).
• Prior to performing site or installation work, inform all utility companies and have all
underground utilities marked.
• Comply with all electrical codes. Electrical equipment and related grounding devices should
be installed by a licensed and qualified electrician.
Elevated Work and Weather
• Exercise extreme caution when performing elevated work.
• Use appropriate equipment and safety practices.
• During installation and maintenance, keep tower and tripod sites clear of un-trained or non-
essential personnel. Take precautions to prevent elevated tools and objects from dropping.
• Do not perform any work in inclement weather, including wind, rain, snow, lightning, etc.
Maintenance
• Periodically (at least yearly) check for wear and damage, including corrosion, stress cracks,
frayed cables, loose cable clamps, cable tightness, etc. and take necessary corrective actions.
• Periodically (at least yearly) check electrical ground connections.
WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS,
THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR
MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS,
ENCLOSURES, ANTENNAS, ETC.
Table of Contents
PDF viewers: These page numbers refer to the printed version of this document. Use the
PDF reader bookmarks tab for links to specific sections.
1. Introduction ................................................................. 1
2. Cautionary Statements ............................................... 1
3. Initial Inspection ......................................................... 1
4. Quickstart .................................................................... 1
4.1 CSIM11 Tutorial .................................................................................. 1
4.2 CSIM11-ORP Tutorial ......................................................................... 4
5. Overview ...................................................................... 7
6. Specifications ............................................................. 8
6.1.1 pH Sensor ...................................................................................... 9
6.1.2 ORP Sensor ................................................................................... 9
7. Installation ................................................................... 9
7.1 Preparation for Use .............................................................................. 9
7.2 Orientation ........................................................................................... 9
7.3 Wiring ................................................................................................ 10
7.4 Datalogger Programming ................................................................... 10
7.4.1 Direct Measurement, Not Temperature Compensated ................ 11
7.4.2 Temperature Compensation of pH Measurement ....................... 11
8. Calibration/ORP Check ............................................. 12
8.1 pH Sensor Calibration ........................................................................ 12
8.2 ORP Check......................................................................................... 12
9. Maintenance .............................................................. 12
9.1 Replacing Reference Electrolyte ........................................................ 13
9.2 Electrode Cleaning ............................................................................. 13
10. Troubleshooting........................................................ 14
Appendices
Importing Short Cut Code ...................................... A-1
A.
A.1 Importing Short Cut Code into a Program Editor ........................... A-1
A.1.1 CRBasic Datalogger................................................................. A-1
A.1.2 Edlog ........................................................................................ A-2
i
Table of Contents
B. Example Programs .................................................. B-1
B.1 CRBasic Program ............................................................................ B-1
B.2 Edlog Programs ............................................................................... B-2
B.2.1 CR10X Program using Edlog’s Expression Editor .................. B-2
B.2.2 CR10(X) Example using Instructions Instead of Edlog’s
Expression Editor .................................................................. B-3
C. Detailed Calibration Procedure and
Manufacturer Tips ................................................. C-1
C.1 Calibration ....................................................................................... C-1
C.2 Tips and Techniques ........................................................................ C-2
Tables
7-1. CSIM11/CSIM11-ORP Wiring ......................................................... 10
7-2. 107 Wiring ........................................................................................ 10
ii
NOTE
CSIM11 pH and ORP Probes
1. Introduction
The CSIM11 measures the full pH range of liquids, and the CSIM11-ORP
measures oxidation reduction potential (ORP) of liquids. They can be
submerged in water or inserted into tanks, pipelines, and open channels. The
reference solutions and bulb configuration are optimized for natural water
applications. Alternate reference solutions and bulb configurations are
available. Contact Campbell Scientific for more information.
2. Cautionary Statements
• READ AND UNDERSTAND the Precautions section at the front of this
manual.
• Do not store the sensor in distilled water, as the gel layer will become
depleted. If this happens, the gel layer can often be rehydrated by soaking
the sensor in the pH 4 buffer solution overnight.
3. Initial Inspection
• Remove the CSIM11 or CSIM11-ORP from its package and check that it
is undamaged. If damaged, contact your supplier for replacement.
• Care should be taken when unpacking and handling all electrodes.
• The probes are shipped with a wetting cap covering the measuring end.
This cap contains a solution of pH 4 buffer saturated with potassium
chloride (KCl).
4. Quickstart
Short Cut is an easy way to program your datalogger to measure the CSIM11
and CSIM11-ORP and assign datalogger wiring terminals. Use the following
procedures to get started.
4.1 CSIM11 Tutorial
A temperature measurement is required. For this tutorial, the 107L thermistor is used.
1. Install Short Cut by clicking on the install file icon. Get the install file
from either www.campbellsci.com, the ResourceDVD, or find it in
installations of LoggerNet, PC200W, PC400, or RTDAQ software.
1
CSIM11 pH and ORP Probes
2. The Short Cut installation should place a Short Cut icon on the desktop of
your computer. To open Short Cut, click on this icon.
3. When Short Cut opens, select New Program.
4. Select Datalogger Model and Scan Interval (default of 5 seconds is
alright for most applications). Click Next.
2
CSIM11 pH and ORP Probes
5. Under the Available Sensors and Devices list, select the Sensors |
Temperature folder. Select 107 Temperature Probe. Click to
move the selection to the Selected device window. Use the data default of
degree Celsius.
6. Under the Available Sensors and Devices list, select the Sensors | Water |
Quality folder. Select CSIM11 pH Probe. Click to move the
selection to the Selected device window. Click on the Solution
temperature (Deg C) reference box and select T107_C. The probe
usually requires an offset adjustment. The white panel at the bottom of the
Properties window provides a procedure for determining the value that
should be entered in the Offset box.
3
Loading...