Page 1
INSTRUCTION MANUAL
CC5MPX and CC5MPXWD
Copyright © 2011- 2016
Campbell Scientific, Inc.
Digital Network Cameras
Revision: 12/16
Page 2
Page 3
Limited Warranty
“Products manufactured by CSI are warranted by CSI to be free from defects in
materials and workmanship under normal use and service for twelve months
from the date of shipment unless otherwise specified in the corresponding
product manual. (Product manuals are available for review online at
www.campbellsci.com.) Products not manufactured by CSI, but that are resold
by CSI, are warranted only to the limits extended by the original manufacturer.
Batteries, fine-wire thermocouples, desiccant, and other consumables have no
warranty. CSI’s obligation under this warranty is limited to repairing or
replacing (at CSI’s option) defective Products, which shall be the sole and
exclusive remedy under this warranty. The Customer assumes all costs of
removing, reinstalling, and shipping defective Products to CSI. CSI will return
such Products by surface carrier prepaid within the continental United States of
America. To all other locations, CSI will return such Products best way CIP
(port of entry) per Incoterms ® 2010. This warranty shall not apply to any
Products which have been subjected to modification, misuse, neglect, improper
service, accidents of nature, or shipping damage. This warranty is in lieu of all
other warranties, expressed or implied. The warranty for installation services
performed by CSI such as programming to customer specifications, electrical
connections to Products manufactured by CSI, and Product specific training, is
part of CSI's product warranty. CSI EXPRESSLY DISCLAIMS AND
EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. CSI hereby disclaims,
to the fullest extent allowed by applicable law, any and all warranties and
conditions with respect to the Products, whether express, implied or
statutory, other than those expressly provided herein.”
Page 4
Assistance
Products may not be returned without prior authorization. The following
contact information is for US and international customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle repairs
for customers within their territories. Please visit www.campbellsci.com to
determine which Campbell Scientific company serves your country.
To obtain a Returned Materials Authorization (RMA), contact CAMPBELL
SCIENTIFIC, INC., phone (435) 227-9000. Please write the issued RMA
number clearly on the outside of the shipping container. Campbell Scientific’s
shipping address is:
CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784
For all returns, the customer must fill out a “Statement of Product Cleanliness
and Decontamination” form and comply with the requirements specified in it.
The form is available from our website at www.campbellsci.com/repair. A
completed form must be either emailed to repair@campbellsci.com or faxed to
(435) 227-9106. Campbell Scientific is unable to process any returns until we
receive this form. If the form is not received within three days of product
receipt or is incomplete, the product will be returned to the customer at the
customer’s expense. Campbell Scientific reserves the right to refuse service on
products that were exposed to contaminants that may cause health or safety
concerns for our employees.
Page 5
Safety
DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND
TRIPODS, TOWERS, AND ANY ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES,
ANTENNAS, ETC. FAILURE TO PROPERLY AND COMPLETELY ASSEMBLE, INSTALL, OPERATE, USE, AND MAINTAIN TRIPODS,
TOWERS, AND ATTACHMENTS, AND FAILURE TO HEED WARNINGS, INCREASES THE RISK OF DEATH, ACCIDENT, SERIOUS
INJURY, PROPERTY DAMAGE, AND PRODUCT FAILURE. TAKE ALL REASONABLE PRECAUTIONS TO AVOID THESE HAZARDS.
CHECK WITH YOUR ORGANIZATION'S SAFETY COORDINATOR (OR POLICY) FOR PROCEDURES AND REQUIRED PROTECTIVE
EQUIPMENT PRIOR TO PERFORMING ANY WORK.
Use tripods, towers, and attachments to tripods and towers only for purposes for which they are designed. Do not exceed design limits.
Be familiar and comply with all instructions provided in product manuals. Manuals are available at www.campbellsci.com or by
telephoning (435) 227-9000 (USA). You are responsible for conformance with governing codes and regulations, including safety
regulations, and the integrity and location of structures or land to which towers, tripods, and any attachments are attached. Installation
sites should be evaluated and approved by a qualified engineer. If questions or concerns arise regarding installation, use, or
maintenance of tripods, towers, attachments, or electrical connections, consult with a licensed and qualified engineer or electrician.
General
• Prior to performing site or installation work, obtain required approvals and permits. Comply
with all governing structure-height regulations, such as those of the FAA in the USA.
• Use only qualified personnel for installation, use, and maintenance of tripods and towers, and
any attachments to tripods and towers. The use of licensed and qualified contractors is highly
recommended.
• Read all applicable instructions carefully and understand procedures thoroughly before
beginning work.
• Wear a hardhat and eye protection, and take other appropriate safety precautions while
working on or around tripods and towers.
• Do not climb tripods or towers at any time, and prohibit climbing by other persons. Take
reasonable precautions to secure tripod and tower sites from trespassers.
• Use only manufacturer recommended parts, materials, and tools.
Utility and Electrical
• You can be killed or sustain serious bodily injury if the tripod, tower, or attachments you are
installing, constructing, using, or maintaining, or a tool, stake, or anchor, come in contact with
overhead or underground utility lines.
• Maintain a distance of at least one-and-one-half times structure height, 20 feet, or the distance
required by applicable law, whichever is greater, between overhead utility lines and the
structure (tripod, tower, attachments, or tools).
• Prior to performing site or installation work, inform all utility companies and have all
underground utilities marked.
• Comply with all electrical codes. Electrical equipment and related grounding devices should be
installed by a licensed and qualified electrician.
Elevated Work and Weather
• Exercise extreme caution when performing elevated work.
• Use appropriate equipment and safety practices.
• During installation and maintenance, keep tower and tripod sites clear of un-trained or non-
essential personnel. Take precautions to prevent elevated tools and objects from dropping.
• Do not perform any work in inclement weather, including wind, rain, snow, lightning, etc.
Maintenance
• Periodically (at least yearly) check for wear and damage, including corrosion, stress cracks,
frayed cables, loose cable clamps, cable tightness, etc. and take necessary corrective actions.
• Periodically (at least yearly) check electrical ground connections.
WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS,
THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR
MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS,
ENCLOSURES, ANTENNAS, ETC.
Page 6
Page 7
Table of Contents
PDF viewers: These page numbers refer to the printed version of this document. Use the
PDF reader bookmarks tab for links to specific sections.
1. Introduction ................................................................ 1
2. Precautions ................................................................ 2
3. Initial Inspection ......................................................... 2
4. QuickStart ................................................................... 2
4.1 Factory Setup ....................................................................................... 3
4.2 Installing Multimedia Player ................................................................ 3
4.3 ActiveX® Controls in Internet Explorer® ........................................... 3
4.4 Setup Using Ethernet ........................................................................... 4
4.4.1 Link Local IP Address Auto-Configuration .................................. 4
4.4.2 Static IP Address Setup ................................................................. 4
4.5 Setup Using Device Configuration Utility ........................................... 8
5. Overview ................................................................... 10
6. Specifications ........................................................... 11
6.1 Specifications ..................................................................................... 11
6.2 System Limitations ............................................................................ 12
6.2.1 High Resolution 5 Megapixel Images ......................................... 12
6.2.2 Simultaneous Processes .............................................................. 13
7. Installation ................................................................ 13
8. Operation .................................................................. 15
8.1 Cables/Wiring .................................................................................... 15
8.1.1 Power and I/O Cable Connections .............................................. 15
8.1.2 Power and I/O Cable Details ....................................................... 17
8.1.3 Ethernet Cables ........................................................................... 18
8.2 Camera Hardware Description ........................................................... 19
8.2.1 Ethernet RJ45 Connection .......................................................... 19
8.2.2 Power and I/O Connection .......................................................... 20
8.2.3 Setup Button/Status LED ............................................................ 20
8.2.3.1 Status LED ....................................................................... 20
8.2.3.2 Setup Button ..................................................................... 21
8.2.4 SD Memory Card ........................................................................ 22
8.2.4.1 Link for Most Recent Image and Video ........................... 22
8.2.4.2 Accessing SD Memory Card ............................................ 23
8.2.4.3 FTP Image Collection from Memory Card ...................... 23
8.2.5 Switched Power Output .............................................................. 24
8.3 Camera Configuration ........................................................................ 24
8.4 Camera Operation using Web Browser Interface ............................... 25
8.4.1 Live Video .................................................................................. 27
i
Page 8
Table of Contents
Real Time Streaming Protocol (RTSP) ........................... 28
8.4.1.1
8.4.2 Network Configuration .............................................................. 29
8.4.2.1 Network Settings ............................................................. 30
8.4.2.2 Ethernet Power Mode Settings ........................................ 31
8.4.2.3 FTP Client Set-up ............................................................ 33
8.4.2.4 SMTP (Email) Server Settings ........................................ 34
8.4.2.5 SNTP (TIME) Server Setting .......................................... 35
8.4.3 System Configuration ................................................................. 36
8.4.3.1 System Date and Time ..................................................... 37
8.4.3.2 Automatic Date and Time Update ................................... 37
8.4.3.3 Site Name ........................................................................ 38
8.4.3.4 Users and Security ........................................................... 39
8.4.3.5 Digital I/O ........................................................................ 40
8.4.3.5.1 External Trigger Input Settings ............................. 41
8.4.3.5.2 Light Power Control Settings ............................... 41
8.4.3.5.3 Communication Power Control ............................ 41
8.4.3.5.4 Heater Power Control ........................................... 41
8.4.3.6 Update ............................................................................. 42
8.4.3.7 Events .............................................................................. 43
8.4.3.8 Save/Read Camera Settings ............................................. 44
8.4.4 Memory Card ............................................................................. 44
8.4.5 Video Settings ............................................................................ 48
8.4.5.1 GPS Coordinates.............................................................. 50
8.4.5.1.1 Example Program – Adding GPS Coordinates
to the Image Banner .......................................... 50
8.4.6 Image Capture ............................................................................ 51
8.4.6.1 Power Modes ................................................................... 52
8.4.6.2 Self Timed Capture1 ........................................................ 55
8.4.6.3 Self Timed Capture2 ........................................................ 60
8.4.6.4 External Trigger ............................................................... 60
8.4.6.4.1 File Transfer Queuing ........................................... 61
8.4.6.4.2 External Trigger Video Pre-Recording ................. 61
8.4.6.5 Motion Detection ............................................................. 65
8.4.6.5.1 CC5MPX Motion Detection Description .............. 66
8.4.6.5.2 Motion Detection Video Pre-Recording ............... 67
8.4.6.6 Save/Read Camera Settings ............................................. 70
8.4.7 Communication Settings ............................................................ 71
8.4.8 Still Image Settings .................................................................... 72
8.4.8.1 GPS Coordinates.............................................................. 75
8.4.8.1.1 Example Program – Adding GPS Coordinates
to Image Banner ................................................ 76
8.5 Internal Jumpers ................................................................................ 76
8.5.1 RS-232/RS-485 Jumpers ............................................................ 76
8.5.2 External Trigger Pull-up/Pull-down Jumper .............................. 77
8.6 RS-232 Communications .................................................................. 78
8.7 RS-485 Communications .................................................................. 79
8.8 PakBus® Communications ............................................................... 80
8.8.1 Concurrent PakBus Communications ........................................ 81
8.8.2 PakBus Graph Operations .......................................................... 81
8.8.2.1 Datalogger Settings.......................................................... 81
8.8.2.2 Discovery ......................................................................... 81
8.8.2.3 Power Modes ................................................................... 81
8.8.3 PakBus Variable Control ............................................................ 82
8.8.3.1 PakBus Control of Window Defroster Function .............. 82
8.8.3.2 PakBus Control of CC5MPX Power ............................... 83
8.8.3.3 Example Program – SendVariable Instruction ................ 83
ii
Page 9
Table of Contents
PakBus Neighbouring Address ................................................... 84
8.8.4
8.9 Device Configuration Utility .............................................................. 84
8.10 Image Quality ..................................................................................... 86
8.10.1 Night Time Images ..................................................................... 86
8.11 Lens .................................................................................................... 86
8.11.1 Camera Lens and Field of View ................................................. 87
8.11.2 Focus and Zoom Adjustment ...................................................... 88
8.11.2.1 Using the Focusing Number ............................................. 89
8.11.3 Temperature Variations and Focus ............................................. 90
8.11.4 Lens IR Cut Filter ....................................................................... 90
8.12 Power Calculations and Timings ....................................................... 90
8.12.1 Standalone Operation .................................................................. 90
8.12.2 Operation with Communications ................................................ 91
8.13 CR1000 Interface Guide .................................................................... 93
8.13.1 CR1000 Memory Setup .............................................................. 93
8.13.2 CR1000 Files Manager ............................................................... 93
8.13.3 CR1000 COM Port (Control Port) Communications .................. 94
8.14 Remote Image Retrieval ..................................................................... 95
8.14.1 LoggerNet File Retrieval ............................................................. 95
8.14.2 Using LoggerNet File Control..................................................... 96
9. Maintenance ............................................................. 98
9.1 Maintenance ....................................................................................... 98
9.1.1 Lithium Battery ........................................................................... 98
9.1.2 Window and Lens Cleaning ........................................................ 98
9.1.3 CC5MPX O-Rings ...................................................................... 98
9.1.4 CC5MPX Desiccant .................................................................... 99
9.2 Backplate Removal Procedures ........................................................ 100
10. Miscellaneous Notes .............................................. 101
10.1 Internal USB Function ..................................................................... 101
10.2 Quick Notes ..................................................................................... 103
10.2.1 CC5MPX General ..................................................................... 103
10.2.2 Campbell Dataloggers Users ..................................................... 104
10.2.3 Configuration Process ............................................................... 104
Appendices
A. CC5MPX Series Cameras and Accessories ......... A-1
A.1 CC5MPXWD .................................................................................. A-1
A.2 CC5MPXFE .................................................................................... A-1
A.3 Window Defroster ........................................................................... A-1
A.4 Power and I/O Cable ....................................................................... A-1
A.5 Environmental Ethernet Cable ........................................................ A-2
A.6 18549 Mounting Kit ........................................................................ A-3
A.7 DB9 FEMALE To Terminal Block Adaptor ................................... A-3
A.8 4091 Desiccant ................................................................................ A-4
B. Window Defroster Option Specifications ............. B-1
B.1 Power Supply ................................................................................... B-1
B.2 Description ....................................................................................... B-1
iii
Page 10
Table of Contents
Figures
1-1. CC5MPX Camera ............................................................................... 1
4-1. Network and Sharing Center ............................................................... 5
4-2. Local Area Connection Properties....................................................... 5
4-3. Internet Protocol Version 4 (TCP/IPv4) Properties ............................. 6
4-4. IP Address Configuration .................................................................... 7
4-5. Web Interface Live Video Homepage ................................................. 8
4-6. CC5MPX shown in Device Configuration Utility............................... 9
4-7. CC5MPX Device Configuration Utility Settings Editor ................... 10
5-1. CC5MPX Digital Camera ................................................................. 11
7-1. CC5MPX Mounting Holes ................................................................ 13
7-2. CC5MPX Mounting Kit .................................................................... 14
7-3. CC5MPX Mounted to Crossarm ....................................................... 15
8-1. CC5MPX Connector Layout ............................................................. 18
8-2. CC5MPX Connector Layout ............................................................. 19
8-3. Image Collection from Installed SD Card ......................................... 24
8-4. CC5MPX Web Interface Homepage ................................................. 26
8-5. Live Video (Homepage) .................................................................... 27
8-6. Network Configuration Warning ....................................................... 29
8-7. Network Configuration Page ............................................................. 29
8-8. Network Settings ............................................................................... 30
8-9. Ethernet Power Savings Settings ....................................................... 31
8-10. FTP Server Settings ........................................................................... 33
8-11. SMTP Server Settings ....................................................................... 35
8-12. SNTP Server Settings ........................................................................ 36
8-13. System Settings ................................................................................. 36
8-14. Date and Time Settings ..................................................................... 37
8-15. Automatic Date and Time Update ..................................................... 38
8-16. Site Name .......................................................................................... 38
8-17. Location of Site Name ....................................................................... 39
8-18. Users and Security Settings ............................................................... 40
8-19. Digital I/O Settings ............................................................................ 40
8-20. Update Menu ..................................................................................... 42
8-21. Event Logs ........................................................................................ 43
8-22. Save/Read Camera Settings ............................................................... 44
8-23. Memory Card Page ............................................................................ 44
8-24. Memory Card Directory Listing ........................................................ 45
8-25. Data Subfolders ................................................................................. 46
8-26. Example Display of Files .................................................................. 47
8-27. Example of Multiple Page Viewing .................................................. 47
8-28. Video Settings Page .......................................................................... 48
8-29. Video Banner Inside Top with Timestamp and Text......................... 48
8-30. Image Capture Page .......................................................................... 51
8-31. Power Modes ..................................................................................... 52
8-32. Self Timed Capture Page ................................................................... 55
8-33. Enable and Capture Time Values ...................................................... 56
8-34. External Trigger Setup Page .............................................................. 62
8-35. Motion Detection Page ...................................................................... 65
8-36. Save/Read Camera Settings ............................................................... 70
8-37. Communication Settings Page ........................................................... 71
8-38. Still Images Settings Page ................................................................. 73
8-39. Internal Jumper Locations ................................................................. 77
8-40. Schematic Showing External Contact Device ................................... 78
8-41. Serial PakBus Port Setting ................................................................ 78
8-42. Connecting the CC5MPX to a 9-Pin RS-232 Port ............................ 79
iv
Page 11
Table of Contents
8-43. Datalogger Connections with RS-232 ................................................ 79
8-44. RS-485 Shown in PakBus Port Setting .............................................. 80
8-45. CC5MPX Device Configuration Option ............................................ 85
8-46. Device Configuration Utility Screen .................................................. 85
8-47. CC5MPX Lens Tube Removal .......................................................... 87
8-48. Zoom and Focus Adjustments ............................................................ 87
8-49. CC5MPX Horizontal Field of View .................................................. 88
8-50. Field of View - Fisheye Lens ............................................................. 88
8-51. Homepage Video Display and Focusing Numbers ............................ 90
8-52. File Retrieval Setup Screen ................................................................ 95
8-53. LoggerNet Connection Screen ........................................................... 97
8-54. USR Drive View in File Control ........................................................ 97
9-1. Backplate O-ring ................................................................................ 98
9-2. Button Cap O-ring .............................................................................. 99
9-3. Front Main Body O-ring .................................................................... 99
9-4. Desiccant Location ........................................................................... 100
9-5. Backplate View ................................................................................ 101
10-1. USB Network Interface .................................................................... 102
10-2. CC5MPX USB Directory ................................................................. 102
10-3. Network Configurations ................................................................... 103
A-1. CC5MPXCBL1-L ........................................................................... A-2
A-2. CC5MPXCBL2-L ........................................................................... A-2
A-3. 18549 Mounting Kit ........................................................................ A-3
A-4. DB9 FEMALE To Terminal Block Adaptor ................................... A-3
A-5. 4091 Desiccant ................................................................................ A-4
B-1. CC5MPX Window Defroster ........................................................... B-2
B-2. Window Defroster with Lens Tube Installed ................................... B-2
Tables
4-1. CC5MPX Default Configuration ......................................................... 3
8-1. Power and I/O Cable Color Connections ........................................... 16
8-2. Power and I/O Cable Wire Usage ...................................................... 17
8-3. Setup Button LED Indicator............................................................... 21
8-4. Network Settings ................................................................................ 30
8-5. Ethernet Power Save Modes .............................................................. 32
8-6. Typical Video File Sizes .................................................................... 50
8-7. Power Modes ..................................................................................... 53
8-8. Capture Response Time ..................................................................... 54
8-9. Start and Stop Time Examples ........................................................... 57
8-10. Self Time Capture Variables .............................................................. 58
8-11. External Trigger Variables ................................................................. 63
8-12. Motion Detection Settings ................................................................. 67
8-13. PakBus Communication Settings ....................................................... 72
8-14. Still Image Settings ............................................................................ 73
8-15. Still Image Resolution Details ........................................................... 74
8-16. Power Consumption (Standalone) ...................................................... 91
8-17. File Transfer Times Using PakBus .................................................... 92
10-1. Power Mode Summary ..................................................................... 105
CRBasic Example
8-1. Adding GPS Coordinates to the Image Banner .................................. 50
8-2. SendVariable Instruction .................................................................... 83
v
Page 12
Table of Contents
vi
Page 13
NOTE
CC5MPX Digital Camera
1. Introduction
FIGURE 1-1. CC5MPX Camera
The CC5PMX Series digital network cameras (FIGURE 1-1) are designed to
meet the stringent operational requirements necessary for remote battery
powered installations while producing images of up to 5 megapixels. Both
cameras can operate over a wide temperature range and have several advanced
power saving modes to suit a variety of needs.
CC5MPX will be used to refer to the series throughout the manual,
unless otherwise specified.
The CC5MPX incorporates an integrated rugged environmental enclosure to
reduce cost and installation time. Communication options include Ethernet,
RS-232, and RS-485. The CC5MPX is fully web-enabled with FTP and email
capabilities. Campbell Scientific’s PakBus® protocol is supported by the
CC5MPX for integration with Campbell Scientific dataloggers. When required,
an optional lens defroster is available.
The camera contains an onboard SD memory card that can turn the camera into
a powerful image and video logger. The onboard memory card enables the
CC5MPX to archive images and video internally.
The CC5MPX can operate in a stand-alone mode with image acquisitions
triggered by the camera’s own precision real time clock. Image and video
acquisitions can also be triggered by events through an external signal or
motion detection.
1
Page 14
CC5MPX Digital Camera
2. Precautions
• READ AND UNDERSTAND the Safety section at the front of this
manual.
• The CC5MPX is a precision instrument containing glass components. Do
not subject to physical shock or drops.
• Avoid strong magnetic fields.
• Store SD memory cards in a case to protect them.
• Do not attempt to disassemble components.
• Use a blower or proper soft cloth to clean the lens.
• Do not exceed voltages as defined in Section 6.1, Specifications
• Desiccant and O-rings should be replaced every two years.
• WARNING: Installations requiring camera to be mounted on tripods,
towers and other elevated structures require following safety guidelines of
those structures.
3. Initial Inspection
• When the CC5MPX is first received, inspect the packaging and contents
for damage. If any damage is found, file a damage claim with the shipping
company.
• Immediately check the package contents. Thoroughly check all packaging
material for product that may be concealed. Check model numbers, part
numbers, and product descriptions against the shipping documents. Each
product will is identified with a printed model number or part number. On
cabled items, the number is often found at the end of the cable that
connects to the measurement device. The Campbell Scientific number may
differ from the part number or model number printed on the sensor by the
sensor vendor. Ensure the expected lengths of any cables ordered are
correct. Contact Campbell Scientific immediately if there are any
discrepancies.
(p. 11).
4. QuickStart
2
• Check the firmware version of the camera against the most recent version
found on the Campbell Scientific website in the CC5MPX support tab and
update as needed.
Ensure that the pigtail end of the power cable is properly terminated (see
Section 8.1, Cables/Wiring
to the camera. If the power supply has an on/off switch, it is also recommended
to switch the power off before connecting the power connector to the camera.
For the initial power up and set up of the camera, it is useful to unscrew the
protective cap that protects the push button and LED indicator.
(p. 15)) before connecting the power cable connector
Page 15
4.1 Factory Setup
TABLE 4-1. CC5MPX Default Configuration
The following outlines some of the CC5MPX settings that are relevant for
initially communicating with the CC5MPX camera:
Configuration Setting Value
Network IP Address 192.168.1.90 (Static)
RS-232 Baud Rate 115200
There are two different ways to set up the parameters in the CC5MPX. The
Ethernet network interface can be used with a web browser or the RS-232
serial lines can be used with Campbell Scientific’s Device Configuration
Utility (DevConfig). The use of RS-232 serial lines will require the use of the
DB9 terminal block adapter (pn 28840) in order to connect to a PC (TABLE
8-1, Power and I/O Cable Color Connections
CC5MPX Digital Camera
Power Mode Fully On
Link Local IP 169.254.99.99
Network Mask 255.255.255.0
Serial I/O Port RS-232
PakBus Address 55
(p. 16)).
When power is first applied to the camera, the LED will turn on and remain
steadily on for about 90 seconds. Once the LED starts flashing, the camera has
initialized properly and is ready for operation.
4.2 Installing Multimedia Player
The use of a multimedia player is required to properly display the video from
the CC5MPX on a computer. VideoLAN® VLC media player® is free, opensource PC software that plays back video on any Windows® computer. The
download is available online at:
www.videolan.org/vlc
Download and install the appropriate VLC media player to the PC that will be
interfacing with the CC5MPX.
4.3 ActiveX® Controls in Internet Explorer®
Currently the CC5MPX is only fully supported using the Windows Internet
Explorer® (32 bit) browser.
The web interface for the CC5MPX requires the use of ActiveX® controls
when using Internet Explorer. These add-ons allow Windows to interact with
objects in the web interface through Internet Explorer.
When connecting to the CC5MPX via the web interface for the first time, a
prompt will appear to run the ActiveX add-ons. The prompt is in the form of a
3
Page 16
CC5MPX Digital Camera
NOTE
4.4 Setup Using Ethernet
4.4.1 Link Local IP Address Auto-Configuration
4.4.2 Static IP Address Setup
‘pop-up’ in Internet Explorer and must be allowed to function with the
CC5MPX.
The CC5MPX supports an automatic IP address configuration in situations
where the camera is directly connected, via Ethernet cable, to a computer
without the need of a DHCP server.
This feature is automatically enabled in the camera and is transparent to its
normal operation. In this situation, the camera will be accessible using the IP
address 169.254.99.99. This address will be valid for accessing the camera in
any network configuration.
In order to use Link Local IP address, the computer connecting to
the CC5MPX must be configured to use DHCP. If the computer
is configured to use a static IP, one of the remaining interface
arrangements will need to be used.
If the computer is not set to use DHCP to obtain an IP address automatically,
follow the procedure outlined in this section to access the camera’s web page.
Consult with an IT department employee if not familiar with configuring
devices for operation on a network.
The default static IP address for the camera is 192.168.1.90. If the standard
assigned static IP address is compatible with the current network, simply plug
the camera into the network and access the web page using this IP. If this IP
address is not compatible with the network, connect the camera directly to the
computer’s Ethernet port in order to change its IP address.
The easiest way to connect to the CC5MPX to change its IP address settings is
to manually configure the computer’s Ethernet IP address to be compatible
with the default address assigned to the CC5MPX.
Administrator access is required to make these changes to the computer’s
network settings. The procedure for changing these network settings in
Windows 7 is explained below:
Connect the CC5MPX camera directly to the computer’s Ethernet port. Use
either a standard Ethernet cable or a crossover Ethernet cable, as the CC5MPX
auto-MDIX feature allows the camera to automatically connect using either
cable.
Open the Control Panel. If in Icon view, click Network and Sharing Center.
If in Category view, click Network and Internet | Network and Sharing
Center (FIGURE 4-1).
4
Page 17
CC5MPX Digital Camera
FIGURE 4-1. Network and Sharing Center
Under Connections on the right-hand-side, click Local Area Connection |
Properties (FIGURE 4-2).
FIGURE 4-2. Local Area Connection Properties
Click on Internet Protocol Version 4 (TCP/IPv4) | Properties.
5
Page 18
CC5MPX Digital Camera
FIGURE 4-3. Internet Protocol Version 4 (TCP/IPv4) Properties
Record the existing settings used on the computer to restore the connection
once the CC5MPX setup is complete. In FIGURE 4-3, the computer is set to
obtain the IP address automatically.
6
Page 19
CC5MPX Digital Camera
Click Use the following IP address and enter to following values (FIGURE
4-4):
• IP address: 192.168.1.91
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.1.1
FIGURE 4-4. IP Address Configuration
Click OK to accept. This may prompt a Microsoft TCP/IP Warning pop-up. If
this pop-up appears, click Yes.
7
Page 20
CC5MPX Digital Camera
It will now be able to open Internet Explorer and access the camera by typing
http://192.168.1.90
connection, the following page should be displayed in the browser (FIGURE
4-5):
or clicking this link. Once the camera establishes a
FIGURE 4-5. Web Interface Live Video Homepage
When selecting a video format to display from the Video Display Size
drop-down box, a prompt will appear to install or allow an ActiveX control. By
default, the browser may be configured to block pop-ups. Pop-ups will need to
be enable for the camera view to function.
Now that a connection has been established, please see Section 8.4.2, Network
Configuration
network settings.
After the changes have been completed, remember to re-enter the computer’s
original IP address settings in the Internet Protocol Version 4 (TCP/IPv4)
Properties window.
(p. 29), for further instructions on how to change the camera’s
4.5 Setup Using Device Configuration Utility
Campbell Scientific provides a free software program called Device
Configuration Utility (DevConfig) that supports the configuration of a variety
of equipment. The CC5MPX can also be configured with DevConfig. Please
visit the Campbell Scientific website to ensure the most recent version of this
utility is installed.
8
Page 21
CC5MPX Digital Camera
The CC5MPX ships from the factory with the communication lines configured
for RS-232. The green wire on the cable is the CC5MPX RS-232 TX (output)
line; the white wire is the CC5MPX RS-232 RX (input) line. A connection will
also need to be made from the CC5MPX black ground to the RS-232 ground.
The CC5MPX comes with a female DB9 to terminal block accessory that
facilitates the connection from the Power and I/O Cable to a 9-pin RS-232
connector. See Section 8.1, Cables/Wiring
(p. 15), for wiring details.
When power is first applied to the camera, the LED will turn on and remain
steadily on for about 90 seconds. Once the LED starts flashing, the camera has
initialized properly and is ready for operation.
DevConfig can now be invoked. Select the CC5MPX as the device type and
choose the appropriate COM port (FIGURE 4-6).
Once the appropriate selections are made, select the Connect button.
FIGURE 4-6. CC5MPX shown in Device Configuration Utility
9
Page 22
CC5MPX Digital Camera
Due to the amount of data the camera has to process, it may take up to 30
seconds for the connection to be completed. Once the settings are loaded,
clicking the tabs located near the top of the page will allow navigation to the
various settings (FIGURE 4-7).
5. Overview
FIGURE 4-7. CC5MPX Device Configuration Utility Settings Editor
The CC5MPX and CC5MPXWD (FIGURE 5-1) are high-resolution digital
cameras with video capabilities. They produce JPG images with a resolution of
up to 5 megapixels and shoot videos with a resolution of up to 720P. Power
conserving modes allow the cameras to be used in remote battery-powered
installations.
Designed to work in harsh environments, the cameras can operate at
temperatures as low as –40 °C and as high as 60 °C. They have an integrated
environmentally sealed anodized enclosure that protects them from moisture
and high-humidity. Additionally, the CC5MPXWD includes a window
defroster that prevents and removes light frost and icing from the camera’s
window.
Flexible configurations allow the cameras to serve as 1) a standalone field
camera, requiring only a battery, solar panel, and available SD memory card, 2)
an IP web camera, or 3) integrated into a Campbell system.
10
Page 23
FIGURE 5-1. CC5MPX Digital Camera
WARNING
6. Specifications
CC5MPX Digital Camera
6.1 Specifications
Power Supply
Operating: 9 to 30 Vdc 250 mA maximum (camera
9 to 16 Vdc 1.0 A max @ 12 Vdc (camera
Quiescent: 1 mA maximum (OFF power mode)
The CC5MPX is specified to operate on a 9 to 30 Vdc
supply input range. When the window defroster is
installed, the 30 Vdc maximum must be reduced to 16
Vdc. Operating the CC5MPX with window defroster at
voltages greater than 16 Vdc can cause damage to the
CC5MPX.
Operating Temperature: –40 to 60 °C
Clock Accuracy: ± 2 minutes/year (–40 to 60 °C)
Lens
Mount: C-type
IRIS: DC compatible
Standard Lens: 4 to 12 mm, 27° to 80° field of view
Zoom Lens: 10 to 40 mm, 9° to 35° field of view
Fisheye Lens: 1.4 to 3.1 mm, 94° to 185° field of view
only)
with defroster option)
Image or Video
Capture Triggers: Two independent selftimers
Motion detection
Web page control
External trigger
11
Page 24
CC5MPX Digital Camera
NOTE
Still Image Resolution (JPEG): 2592 x 1944 640 x 352
1280 x 960 320 x 240
1280 x 720 320 x 176
640 x 480
Video: Capable of 720P to 1280 x 720 (MPEG4),
640 x 480 (live video only/MJPEG),
320 x 240 (MPEG4)
External Input Signal
Logic Low Level: < 0.65 V (–20 Vdc absolute min)
Logic High Level: > 2.0 Vdc (20 Vdc absolute max)
Minimum Pulse Width: 10 ms
Communication Interfaces: Ethernet 10/100
RS-232 port
RS-485 port
Communication Protocols: Web page interface via web browser
FTP
Email
PakBus® (for Campbell dataloggers)
Communication Switched Power Output
Maximum Output Current: 750 mA
RS-232 and RS-485
Maximum Baud Rate: 115.2 kbps
The recommended maximum cable length at this baud rate is 15
meters. The use of the 57.6 kbps rate has a recommended
maximum cable length of 30 meters.
Memory Card Interface
Type: Secure Digital (SD)
File System: FAT32
File Type: JPEG (image), AVI (video)
Size: Verified up to 16 GB
Dimensions
Length: 220 mm (8.7 in)
Width: 93 mm (3.7 in)
Weight: 1.06 kg (2.34 lb)
6.2 System Limitations
This section outlines some system limitations that exist in the CC5MPX
camera.
229 mm (9.0 in) with zoom lens
12
6.2.1 High Resolution 5 Megapixel Images
The capturing of 5 MP pictures results in longer capture times than other image
resolutions. When a 5 MP image is captured, the continuous video stream is
paused, the image sensor is reconfigured, and then the 5 MP image is captured.
Page 25
6.2.2 Simultaneous Processes
7. Installation
CC5MPX Digital Camera
This longer delay time would be noticeable when capturing images from the
external trigger. 5 MP images would take several seconds from the external
trigger signal being asserted. All other still image captures are less than 1
second.
The CC5MPX cannot capture two events simultaneously. For example, the
CC5MPX cannot capture a still image while video is being recorded. Also
other processes such as downloading files from the memory card can add
additional delays to the capture process.
The camera enclosure is designed to be environmentally sealed for outdoor
installations. The enclosure provides protection from moisture or high
humidity. It is not intended for operation under water. All that is required is an
appropriate mounting fixture.
FIGURE 7-1. CC5MPX Mounting Holes
The camera is equipped with a set of three ¼-20 threaded mounting holes (see
FIGURE 7-1). These mounting holes are centered along the bottom of the
camera and are spaced 25.4 mm (1.0 in) apart from one another. At least two of
the ¼-20 threaded holes are required for mounting the camera.
13
Page 26
CC5MPX Digital Camera
FIGURE 7-2. CC5MPX Mounting Kit
When using the optional mounting kit (pn 18549) as shown in FIGURE 7-2,
align the outer holes of the CC5MPX with the center hole and the 180° slot of
the mount. Loosely secure the two together with the two ¼-20 x 0.5 in. Hex
bolts, lock washers, and washers included with the kit. It is now possible to
mount the CC5MPX to either a crossarm or other mounting surface with the
included U-bolt.
With the hardware loose, the camera and the 18549 mounting kit can be
pivoted to allow a full range of motion when aiming the camera. The hardware
should be secured once the camera is properly aimed at the intended target
(FIGURE 7-3).
The focus of the camera should be checked and adjusted as required. Refer to
Section 8.11.2, Focus and Zoom Adjustment
(p. 88), for details. Be sure that the
lens tube is fully seated, the sun shroud is properly oriented after the camera is
aimed, and any protective caps are properly secured.
The sun shroud can be adjusted by loosening the Philips screws and turning the
shroud; do not over tighten the screws as the shroud may crack. A light torque
is all that is required to hold the shroud in place.
14
Page 27
CC5MPX Digital Camera
NOTE
Sun Shroud
Lens Tube
Curved Slots
¼-20 x 0.5 in
Hex Bolt
U-bolts
Crossarm
Split Washer
Washer
Bolt
8. Operation
8.1 Cables/Wiring
8.1.1 Power and I/O Cable Connections
FIGURE 7-3. CC5MPX Mounted to Crossarm
The wiring for the Power and I/O Cable connector assemble is as shown in
TABLE 8-1. The wires can be terminated directly on the control ports of a
compatible datalogger.
It is essential that the ground cable be connected first when wiring
the camera to the datalogger or the power supply.
15
Page 28
CC5MPX Digital Camera
TABLE 8-1. Power and I/O Cable Color Connections
Color Function Connection
Black Power Ground System Ground
Red Input Power Power Source 9-30 Vdc
RS-232 Input (RX control port of
datalogger or Pin 2 of a computer (DTE)
Green RS-232 TX (output)
DB9 Connector)
RS-485A when configured to RS-485
RS-232 Output (TX control port of a
datalogger or pin 3 of a computer (DTE)
White RS-232 RX (input)
DB9 connector)
RS-485B when configured to RS-485
This line is intended to power a
communication device. The camera
switches the input power voltage to this
line.
Yellow
Communication
Switched Power
(Output)
Connect to external signal source (i.e.
Blue
External Trigger
(Input)
datalogger control port). The external
signal wakes up or initiates image/video
acquisition.
Clear Shield Shield/Earth Ground
Refer to Section 8.5, Internal Jumpers
(p. 76), if the current RS-232 or RS-485
interface option needs to be changed in the camera.
Refer to TABLE 8-2 to help determine which wires will need to be connected
for the camera application.
16
Page 29
CC5MPX Digital Camera
TABLE 8-2. Power and I/O Cable Wire Usage
Wire
Color
Black Power Ground Always
Red Input Power Always
Green
White
Communication
Yellow
switched power
Function
RS-232 TX
(output)
OR
RS-485A
RS-232 RX
(input)
OR
RS-485B
(output)
Connection Required
The green wire only needs to
be connected when RS-232
or RS-485 communications
are used for PakBus® or
DevConfig.
The white wire only needs to
be connected when RS-232
or RS-485 communications
are used for PakBus® or
DevConfig.
When the camera is being
used to manage power to a
communication modem.
For solar powered sites, the
camera can remove power
from the modem when
communications are not
required.
When not
Used
Connect to
a grey
terminal
block
Connect to
a grey
terminal
block
Connect to
a grey
terminal
block
Blue
Clear Shield Always
External trigger
(input)
8.1.2 Power and I/O Cable Details
The Power and I/O Cable that is used for the CC5MPX camera has an outdoor
environmentally rated screw type connector on one end and discrete wire
pigtails on the other end that allow for flexible termination. When making the
cable connection to the camera, the notch positions should always be lined up
and care should be taken to not cross the connector.
When another device is
being used to trigger the
camera to capture images or
video. This can be a
datalogger, a motion sensor,
or a set of contacts.
Another device can also help
keep the camera in the Fully
On power mode by leaving
the External Trigger Input
asserted.
Connect to
ground if
left in
Factory
Default
settings
17
Page 30
CC5MPX Digital Camera
Cable specifications:
• 24-AWG 3 pair (6 conductor) Individually Shielded Cables with
Santoprene® Jacket
• IP-67 rated connector
• 10 inch pigtail for termination
• 3 Single Pole 16 to 20 AWG Grey Push Operated Connector
Terminals (FIGURE 8-1)
• Maximum recommended cable length is 20 m (100 ft)
Longer cable lengths can be used; however, a heavier gauge wire is suggested.
It is recommended that the individual wire resistance on the +12 Vdc and
ground conductors not exceed 2.7 ohms. Using longer cable in conjunction
with RS-232 communications will require slower baud rates. Depending on the
cable length and type of cable, RS-232 may not be suifor communications and
the use of RS-485 should be considered.
18
FIGURE 8-1. CC5MPX Connector Layout
For information about the cable options available, see Appendix A, CC5MPX
Series Cameras and Accessories
8.1.3 Ethernet Cables
The Ethernet connection is used to configure the camera settings as well as for
targeting and focusing the camera. The Ethernet port of the CC5MPX is auto
MDIX; therefore, an Ethernet crossover cable is not required when connecting
the camera to other devices.
(p. A-1).
Page 31
A standard CAT5 (or better) Ethernet cable with RJ45 connectors (pn 28900)
can be used to interface to the camera in indoor conditions or for temporary
connection outdoors when conditions permit. When an Ethernet connection is
required for permanent outdoor installations or when a connection to the
camera is required in wet or harsh conditions, the Environmental Ethernet
Cable assembly (pn CC5MPXCBL2-L) needs to be used.
The Environmental Ethernet Cable assembly provides one end with an
environmental connector that provides a weatherproof connection when
properly mated to the camera. The other end of the cable consists of a standard
RJ45 connector. The Environmental Ethernet Cable is meant to provide an
Ethernet connection between the CC5MPX and a network router, a cellular
modem, or a laptop.
Details of the Environmental Ethernet Cable are as follows:
• CAT5E shielded cable with polyurethane jacket.
• IP67 environmentally rated RJ45 connector on one end and a regular
RJ45 connector on the second end.
• Maximum recommended cable length 70 m (230 ft).
8.2 Camera Hardware Description
CC5MPX Digital Camera
FIGURE 8-2. CC5MPX Connector Layout
8.2.1 Ethernet RJ45 Connection
The RJ45 connector on the camera, shown in FIGURE 8-2, is meant to
interface the CC5MPX with either a network router, a cellular modem, or
directly to a laptop.
If a permanent Ethernet connection is not required for an outdoor environment,
then the protective cap must be securely attached to the Ethernet connector to
provide an environmental seal.
19
Page 32
CC5MPX Digital Camera
NOTE
8.2.2 Power and I/O Connection
When the protective cap is removed, a standard cable with an RJ45 connector
can be used to connect the camera to another device in an indoor environment
or temporarily outdoors if weather permits.
If a permanent Ethernet connection is required outdoors or if a connection is
required in wet or harsh locations, the Environmental Ethernet Cable must be
used.
The maximum cable length for the Ethernet cable is 70 m (230 ft).
The CC5MPX does not support the PakBus communication
protocol over Ethernet.
Connection to the Power and I/O connector is necessary for camera operation
and it is the only means to supply power to the camera. The connector that
connects to the Power and I/O connector provides a weather tight connection
and has an IP67 environmental rating when properly connected.
When making the cable connection to the camera, the notch positions should
always be lined up and care should be taken to not cross thread the connector.
8.2.3 Setup Button/Status LED
The Setup button is located behind a protective metal cap on the camera. The
Setup button also contains an integrated Status LED for user feedback.
To access the LED, unscrew the protective cap to expose the button/LED. It is
highly recommended to place the protective cap back on for improved
environmental protection.
8.2.3.1 Status LED
The Status LED located in the center of the button provides some useful
diagnostic information about the camera. TABLE 8-3 describes the LED
behavior.
20
Page 33
CC5MPX Digital Camera
TABLE 8-3. Setup Button LED Indicator
LED CC5MPX State Other
No power or the camera is in
one of the following Low
Continuously
Off
Slow Flash
1 sec on,
3 sec off
Rapid Flash
LED CC5MPX State Other
Continuously
On
Powered Modes:
• Partially On
• Deep Sleep
• OFF
Normal Operation in Fully
On power mode
Exit from low power state.
The camera is being kept on
by:
• Timeout (from the
Setup button press)
• Communications
• Asserted External
Trigger
• Image or video
acquisition
The camera is booting up.
The booting up process takes
approximately 90 sec.
Pressing the Setup button
will force the camera to
exit any of the low
powered modes and remain
fully on for a period of 5
min with the LED rapidly
flashing
The camera will be
required to boot up
whenever:
• Power is first
applied to it
• The camera is
exiting the OFF
power mode to
perform an
operation.
8.2.3.2 Setup Button
The primary function of the Setup button is to wake the camera from any of
the power saving modes that it may be in. Once the Setup button is pushed the
CC5MPX enters a fully powered mode for 5 minutes. During this interval, it is
possible to access the camera via Ethernet or RS-232/485 and make any
necessary configuration changes. If no communications occur during the 5minute window, the camera will return to its configured power saving mode
and continue normal operation.
The secondary function of the Setup button is to facilitate a power down
procedure. If the button is held for a period of 10 seconds, the camera will
completely shut down for a period of 10 minutes. During this interval, it is
possible to remove power from the camera and avoid possible corruption of the
21
Page 34
CC5MPX Digital Camera
CAUTION
NOTE
8.2.4 SD Memory Card
memory card. This function is also available through the camera web interface
via the Shutdown Camera button box.
The camera is internally equipped to use an SD memory card. An extended
temperature memory card (pn 27506 for a 4 GB card, pn 27507 for an 8 GB
card) is available as an option for the CC5MPX.
If using an SD memory card from another source, it will need to be formatted
with a PC using the FAT32 format.
Image files can be stored on the SD memory card as JPEG files and video files
are stored as AVI files. Individual image and video files are uniquely named
with a sequence number, or with a date and time stamp. The directory location
will correspond to the camera configuration and the method of triggering (i.e.,
motion detection).
The use of the card for image and video storage is entirely configurable to fit
the needs of a given application. Individual image or video capture can be
configured to manage memory card files as either a fill and stop, or with a ring
memory.
Access to the SD card requires removal of the camera backplate. Insertion or
removal should only be done when power is removed. See Section 8.2.4.2,
Accessing SD Memory Card
retrieval from the SD card. It is generally recommended to delete older image
files from the memory card after downloading them to a permanent storage
location.
Once the contents of the memory card are read or downloaded, it is
recommended to reformat the memory card (using FAT32) to delete the entire
contents. The CC5MPX writes binary files to the memory card to facilitate file
management.
Deleting or editing the contents of the memory card
manually outside of the camera will invalidate the binary
files, causing image and video storage to function
unpredictably.
8.2.4.1 Link for Most Recent Image and Video
There are also permanent links available in the CC5MPX web server to
download the most recently captured images or video files available on the SD
card. Each capture method has its own link. These links redirect to the actual
files on the SD card, which means for continuity that the downloaded filename
will be the same as the filename on the SD card.
(p. 23), for more information on image and video
22
The following are examples and the IP address will vary with the
camera’s network configuration.
Page 35
• Self Timed 1:
o http://192.168.1.90/stc1.jpg
o http://192.168.1.90/stc1.avi
• Self Timed 2:
o http://192.168.1.90/stc2.jpg
o http://192.168.1.90/stc2.avi
• External Trigger:
o http://192.168.1.90/etc.jpg
o http://192.168.1.90/etc.avi
• Motion Detection:
o http://192.168.1.90/mdc.jpg
o http://192.168.1.90/mdc.avi
8.2.4.2 Accessing SD Memory Card
In order to access the SD memory card, the backplate of the CC5MPX must be
removed. Before starting this process, remove the CC5MPX from any power
supply and disconnect any attached cabling.
CC5MPX Digital Camera
Refer to Section 9.2, Backplate Removal Procedures
removing the camera backplate.
The SD memory card is located on the main circuit board and can be removed
by first pressing the card into the housing until a click is heard. The card can
now be pulled from the card housing.
In order to properly reinstall the card, place it into the housing and press in
until a click is heard.
Once finished with the SD card, replace the backplate. First ensure the O-ring
is still seated properly on the backplate. This is very important as the O-ring is
required to properly seal the camera.
The backplate can only be seated in the orientation that aligns the flat surfaces
of the backplate and the bottom of the camera body. This will also help align
the screw holes. The six screws can now be threaded and hand tightened. Be
sure the two plastic washers are located between the tether chains and the
backplate.
8.2.4.3 FTP Image Collection from Memory Card
If the camera is setup to store images to the memory card, it may be necessary
to collect all the images from the memory card. The web interface does provide
a user friendly method of viewing and saving select files from the memory
card. However, if it is desired to collect a large number of files from an entire
folder then using the web interface is very cumbersome.
(p. 100), for details on
It is recommended to access the CC5MPX memory card using the FTP file
transfer process. On most Windows® machines this is easily done by typing:
ftp://192.168.1.90:85
into Windows Internet Explorer®, where ‘192.168.1.90’
is the IP address of the camera and the ‘:85’ is the port used for FTP access.
The camera supports FTP access to the memory card on port 85 of the camera.
This will require an Ethernet connection to the camera.
23
Page 36
CC5MPX Digital Camera
Clicking a directory such as SelfTimed1Still (FIGURE 8-3) will begin the
navigation into that directory. Whole directories or files can be saved, just like
any other Windows folder.
FIGURE 8-3. Image Collection from Installed SD Card
8.2.5 Switched Power Output
The intended purpose of the switched power output is to control the power for
a communication device. One common application is to have the camera
control the power to a communication modem at a solar powered site. Refer to
Section 8.4.2.5, SNTP (TIME) Server Setting
the switched power output via the web interface.
This power management feature can greatly reduce the system power
requirements by only turning on the modem when required to transmit an
image or video. The switched power output will turn on under the following
conditions:
• The camera in one of its low power modes and the Setup button is
pressed. The camera will exit the low power mode and stay awake for
5 minutes with the switched power output on.
• A low power mode is selected and the camera wakes up from an event
where communications are required. This will include FTP, SMTP
(email), or PakBus transfers. Events requiring memory card storage
only, will not turn on the switched power output as these events would
not require a modem for communications.
8.3 Camera Configuration
There are two methods for a user to configure the CC5MPX camera that do not
require opening the camera.
(p. 35), for details on configuring
24
The first is by using the web interface of the camera. This is the best way to set
up the camera. Most users will need to communicate with the camera via the
Page 37
CC5MPX Digital Camera
Ethernet connection in order to facilitate focusing and targeting of the camera
when installed.
The other means of setting up the camera is by using the RS-232 serial lines on
the Power and I/O cable and using Campbell Scientific’s DevConfig software
to change configuration parameters in the camera (Section 8.6, RS-232
Communications
(p. 78)). DevConfig is a free download from any Campbell
Scientific website.
If it is not possible to connect to the camera via the Local Area Connection due
to a loss of configuration information, DevConfig must be used.
A third method is available that involves opening up the camera to access the
internal USB connector. Refer to Section 10.1, Internal USB Function
for more details.
8.4 Camera Operation using Web Browser Interface
The web interface allows the user to:
• Fully configure the CC5MPX, as required.
• View information, system status, date, and time.
• View live video for the purpose of targeting and focusing the camera.
(p. 101),
The CC5MPX supports an automatic IP address configuration in situations
where the camera is directly connected via Ethernet cable to a computer. The
camera is accessible using the IP address 169.254.99.99.
The camera ships with the default static IP address of 192.168.1.90 and a
Network Mask of 255.255.255.0. It is highly recommended to keep track of
any changes made to the network settings.
Refer to Section 4.4, Setup Using Ethernet
(p. 4), for details on making the initial
network connection to the camera. To establish communications with the
camera, use one of the methods previously discussed. Enter the appropriate IP
address in the address bar of Internet Explorer. After typing the address, the
homepage of the CC5MPX camera, as shown in FIGURE 8-4, will appear.
Currently, only Windows Internet Explorer web browser is supported for use
with the CC5MPX camera.
25
Page 38
CC5MPX Digital Camera
FIGURE 8-4. CC5MPX Web Interface Homepage
Some general items to remember about the web interface are:
• The homepage of the camera is the Live Video page. There are no
operational settings to change on the Live Video page.
• If any settings are changed or added on any of the other pages, then
the Submit button must be keyed to accept the changes. If the Submit
button is not keyed, the changes will not be saved.
26
Page 39
8.4.1 Live Video
Still Image
Capture
Page
Tabs
CC5MPX Digital Camera
The Live Video homepage of the CC5MPX is shown in FIGURE 8-5.
FIGURE 8-5. Live Video (Homepage)
The homepage allows the user to manually capture still images or view real
time video. The use of these features aids in the installation of the camera and
testing the images.
When the Video Display Size is changed from off to one of the video size
settings, video should be displayed in the video display area. If the video
cannot be viewed, review Section 4, QuickStart
(p. 2).
The Still Capture box allows for the manual capture of still images. Select the
desired size and method of capturing. The two methods of capturing include
storing the image to the SD card in the directory ManualStill, or Save as File
option, which enables the picture to be saved to the computer.
The Shutdown button provides a safe power down sequence. If at all possible,
the Shutdown button should be used any time the power needs to be removed
from a camera that is actively collecting and storing images or video. It will
completely shut down for a period of 10 minutes and ensure the memory card
is not corrupted. An alternate way of shutting down the camera is to hold the
Setup button for at least 10 seconds.
27
Page 40
CC5MPX Digital Camera
Important!
NOTE
Information features on the Live Video homepage include:
• Motion Detection Indicator
o Turns from green to red when motion is detected.
o This will indicate even if the motion capture is not enabled.
• External Trigger Status
o Reflects the state of the External Trigger signal on the Power and
I/O cable.
• System Status
o Indicates the SD card presence, absence or scanning. Note that
the scan process can take several minutes to complete, and is
invoked if the camera is shut down by an unexpected reset or
power removal.
o Displays system messages.
• Internal Board Temperature Value
o When Fully On, the internal temperature can be 10 to 15 °C
above ambient.
• Focusing Numbers
o Facilitates focusing. (Note: If the camera is targeted on an object
that is far away (100 m or more), it may be beneficial to adjust
the lens before taking the camera into the field by using an object
that is at a similar distance away.)
o See Section 8.11.2.1, Using the Focusing Number
(p. 89).
• Date and Time
The Live Video homepage, as well as every other page, also contains a
navigation bar with tabs that allow navigation to the other CC5MPX web
pages. These are called Page Tabs.
Any configuration changes made in the web interface must be
‘submitted’ to save and activate changes, or changes will be lost.
8.4.1.1 Real Time Streaming Protocol (RTSP)
Users can access the live video stream outside of our ActiveX® control using
RTSP. Only the 640 x 480 resolution is available.
If a user is viewing the RTSP video stream and another user tries
viewing a different resolution using the camera web page, the
RTSP stream will stop.
The following sample code can be used to embed the video stream into a web
page. The IP address will need to be appropriately changed.
28
Page 41
CC5MPX Digital Camera
Page Tabs
Sub Tabs
<OBJECT classid="clsid:9BE31822-FDAD-461B-AD51-BE1D1C159921"
codebase="http://downloads.videolan.org/pub/videolan/vlc/latest/win32/axvlc.cab"
width="640" height="480" id="vlc" events="True">
<param name="Src" value="http://192.168.1.90/ipcam/mjpeg.cgi" />
<param name="ShowDisplay" value="True" />
<param name="AutoLoop" value="False" />
<param name="AutoPlay" value="True" />
<embed id="vlcEmb" type="application/x-google-vlc-plugin"
version="VideoLAN.VLCPlugin.2"
autoplay="yes" loop="no" width="640" height="480"
target="http://192.168.1.90/ipcam/mjpeg.cgi" ></embed>
</OBJECT>
sic
8.4.2 Network Configuration
To access the main Network Configuration page, simply click the Network
page tab.
When the Network page is first entered, the following prompt appears as a
warning (see FIGURE 8-6). If changes are made to the camera that affects the
access to the web interface, the browser must be restarted with the new
configuration.
For example, if the IP address of the camera is changed, the changes will be
accepted by clicking on the Submit button, and the new IP address will be in
effect.
FIGURE 8-6. Network Configuration Warning
FIGURE 8-7. Network Configuration Page
The Network page displayed in FIGURE 8-7 allows the user to configure
settings that are related to the CC5MPX network connectivity.
29
Page 42
CC5MPX Digital Camera
TABLE 8-4. Network Settings
8.4.2.1 Network Settings
To clarify, this manual will refer to the selection tabs that are located on the left
of some of the pages as sub tabs.
The main Network page has five sub tabs:
• Network
• Power Mode
• FTP Server
• SMTP Server
• SNTP
The most common network settings (FIGURE 8-8) are displayed first in the
Network sub tab. These settings are summarized in TABLE 8-4.
Configuration
Settings
Enables DHCP operation of the
DHCP
IP Address Only set if DHCP is Disabled
Netmask Only set if DHCP is Disabled 255.255.255.0
Default Gateway Only set if DHCP is Disabled 192.168.1.1
Primary
Nameserver
HTTP Port
network interface. Operates as a
Static IP address if Disabled.
Only set if DHCP is Disabled 192.168.1.1
Alternate ports can be used for the
http interface. Options are 80 or
values between 1025 and 65535.
Description
Default Value
Disabled
192.168.1.90
(Static)
80
30
FIGURE 8-8. Network Settings
Page 43
8.4.2.2 Ethernet Power Mode Settings
Clicking on the Power Mode sub tab allows the user to edit the Ethernet power
mode settings. To reduce power consumption, the CC5MPX includes the
ability to control the power characteristics of the Ethernet port. Three options
are available (see FIGURE 8-9):
• Always On
This power mode offers the maximum availability of the Ethernet
port. If the camera is in the Fully On power state or the Partially On
power state, the Ethernet port will always be on and available for
communications.
• Moderate
This power mode offers some power savings on the Ethernet port.
This mode is only recommended if the camera is in Partially On
power mode. If the camera is in the Partially On power mode,
incoming data packets will wake up the camera for communications.
• Full Power Save
This power mode should be used if the lowest power consumption is
desired and incoming Ethernet communications are not required.
CC5MPX Digital Camera
FIGURE 8-9. Ethernet Power Savings Settings
The specific behavior of the camera’s Ethernet power save is also influenced
by the power mode of the camera. TABLE 8-5 will help outline the Ethernet
power saving features versus various power modes of the camera.
31
Page 44
CC5MPX Digital Camera
TABLE 8-5. Ethernet Power Save Modes
Camera
Power
Mode
Fully On
Partially On
Ethernet
Power Save
Mode
Always On
Moderate
Power Save
Full Power
Save
Always On
Moderate
Power Save
Operating Characteristics
• Camera is always on.
• Highest power consumption.
• Ethernet is on and always available for incoming communications.
• Not recommended.
• Camera is always on.
• Average power consumption is reduced by 50 mA @ 12 Vdc.
• Ethernet is normally turned off and is only enabled when outgoing
communications are required (email or FTP).
• User needs to push the Setup button to temporarily enable the Ethernet port
for web page access.
• The camera is effectively off in a low powered state.
• Typical power consumption is 80 mA @ 12 Vdc.
• Ethernet is always on and always available for incoming communications.
• The camera will temporarily wake up to the Fully On power mode when
traffic occurs on the network. In situations where there is constant network
traffic, the camera may effectively be in the Fully On power mode.
• The camera is effectively off in a low powered state.
• Typical power consumption is 80 mA @ 12 Vdc.
• Ethernet is always off.
• Disconnecting and connecting the camera to another Ethernet device will
momentarily wake up the camera to allow it to process incoming
communications. The camera will go into the low powered mode again if no
communications occur.
32
• The camera is effectively off in a low powered state.
• Average power consumption is typically 10 mA @ 12 Vdc.
• The Ethernet is normally turned off and is only enabled when outgoing
Full Power
Save
communications are required (email or FTP).
• User needs to push the Setup button to temporarily enable the camera and
Ethernet port for web page access.
• The camera can respond to RS-232 and RS-485 communications in this
mode.
Page 45
CC5MPX Digital Camera
TABLE 8-5. Ethernet Power Save Modes
Camera
Power
Mode
Deep Sleep
OFF
Ethernet
Power Save
Mode
Always On
Moderate
Power Save
Full Power
Save
Always On
Moderate
Power Save
Full Power
Save
Operating Characteristics
• The Deep Sleep power consumption (6 mA typically) is not affected by the
Ethernet power mode.
• Ethernet, RS-232, and RS-485 communications are non-responsive in Deep
Sleep state.
• Not recommended.
• The Deep Sleep power consumption (6 mA typically) is not affected by the
Ethernet Power Mode.
• If Ethernet communications are not used this can reduce the power
consumption of the camera by 50 mA when the camera exits the Deep Sleep
state.
• The OFF state power consumption (1 mA typically) is not affected by the
Ethernet power mode.
• Ethernet, RS-232 and RS-485 communications are non-responsive in OFF
state.
• Not recommended.
• The OFF state power consumption (1 mA typically) is not affected by the
Ethernet power mode.
• If Ethernet communications are not used this can reduce the power
consumption of the camera by 50 mA when the camera exits the OFF state.
8.4.2.3 FTP Client Set-up
Clicking on the FTP Server sub tab will display the FTP Server settings (see
FIGURE 8-10).
FIGURE 8-10. FTP Server Settings
33
Page 46
CC5MPX Digital Camera
8.4.2.4 SMTP (Email) Server Settings
These settings configure the CC5MPX to be able to act as an FTP client to
send image files to an FTP server. There are settings for two different servers.
These settings configure the parameters that the camera will use to connect to
the server. The FTP transfers must be enabled in the Image Capture menus.
When specifying an FTP connection, the user can select between active and
passive mode file transfers. The default setting is the passive mode. This mode
allows a camera connected through a firewall to transfer files properly though
the firewall to the remote server.
In the event of an FTP transfer failure, the CC5MPX will retry sending the file
to the FTP server up to two times before aborting the file transfer.
The CC5MPX can also act as an FTP server to enable images and video to be
transferred from the memory card. See Section 8.2.4.3, FTP Image Collection
from Memory Card
(p. 23), for more details.
Clicking on the SMTP Server sub tab will display the SMTP (email) server
settings (see FIGURE 8-11). The CC5MPX can send images or video via email
by using two different email servers.
Many SMTP servers are capable of using TLS encryption to securely
communicate with email clients. Some SMTP servers, such as Google Gmail®,
require secure connections in order to allow access. Support for TLS
encryption is available in the CC5MPX SMTP program. If the CC5MPX
connects to an SMTP server that supports TLS encryption, it will automatically
be used, otherwise it will return to a normal, unencrypted connection.
In the event of a SMTP transfer failure, the CC5MPX will retry sending the file
to the mail server up to two times before aborting the file transfer.
Details on the settings are as follows:
• My Server Requires Authentication
Select this setting if the email server requires authentication. This
usually means that a login is required, with a username and password.
• Account Name
The Account Name is required only if Authentication is used.
• Password
The Password is required only if Authentication is used.
• Sender
The email address associated with the account is normally used here.
The CC5MPX cannot receive emails.
34
• SMTP Server
Enter the address of the SMTP server that is being used. Enter the
SMTP server port number as part of the SMTP address, if required.
The camera will default to port 25 if a value is not included. An
example of a port number entry is: mail.server.com:587
Page 47
CC5MPX Digital Camera
• Email Address
Enter the destination email addresses that are to receive the emails.
Multiple email addresses can be included. There is a limit of 255
characters. For multiple email addresses, use a space, comma or
semi-colon as a separator between addresses. Example:
test1@somewhere.com;john@email.com
.
FIGURE 8-11. SMTP Server Settings
8.4.2.5 SNTP (TIME) Server Setting
Clicking on the SMTP Server sub tab will display the SNTP (TIME) server
settings (see FIGURE 8-12). The configuration of an SNTP server provides a
means of synchronizing the onboard clock of the CC5MPX with the specified
SNTP server. This ensures that the camera clock is always accurate. It is also
possible to configure a time zone offset for the camera.
Other than the address of the SNTP server, the time zone needs to be selected
and the Automatically Adjust for Daylight Saving Time Changes can also be
selected.
Refer to www.pool.ntp.org/zone/us for SNTP server information covering the
United States.
Refer to www.pool.ntp.org/zone/ca for SNTP server information covering
Canada.
35
Page 48
CC5MPX Digital Camera
8.4.3 System Configuration
FIGURE 8-12. SNTP Server Settings
Selecting the System page tab activates the System Settings page (see FIGURE
8-13). The main System Settings page has eight sub tabs:
• Date and Time
• Automatic Date and Time Update
• Site Name
• Users/Security
• Digital I/O
• Update
• Events
• Save/Read Camera Settings
36
FIGURE 8-13. System Settings
Page 49
8.4.3.1 System Date and Time
The Date and Time submenu (see FIGURE 8-14) provides a means for
viewing and setting the current date and time of the camera. Available options
include:
• Setting the Time manually:
• Synchronize with Computer Time:
• Synchronize with SNTP Server
CC5MPX Digital Camera
Select the Set Manually button and enter the date and time values
from the drop-down boxes. Click the Submit button for the settings to
take effect.
The web page also displays the time reported by the computer. If this
is the desired time, select the Synchronize with Computer Time
button and click Submit. The camera time will be updated with the
computer time.
If an appropriate SNTP time server is set up in the Network Settings,
this button can be selected to use an Internet SNTP time server.
Clicking on Submit starts the process.
FIGURE 8-14. Date and Time Settings
8.4.3.2 Automatic Date and Time Update
The Automatic Date and Time submenu (see FIGURE 8-15) configures the
camera for automatic date and time updates. The setting parameters are:
• Time Variance in Seconds to perform clock update.
Select the minimum allowable variance that will result in the camera’s
time being changed.
37
Page 50
CC5MPX Digital Camera
• Source Options
Select 1 of 3 options for the Automatic Time updates. The
possibilities are:
o None
The camera’s clock is highly accurate and its drift is
normally less than 2 min/year.
o PakBus Port
Normally this is a datalogger. The actual time update occurs
only when a file transfer occurs to the datalogger from the
camera.
o SNTP Server
The camera will use the SNTP time server that is specified
under Network settings (see Section 8.4.2.5, SNTP (TIME)
Server Setting
(p. 35)). A proper network connection is also
required. The time will update on every power up and wake
out of sleep mode, as well as every 8 hours in Fully On
mode.
8.4.3.3 Site Name
FIGURE 8-15. Automatic Date and Time Update
The Site Name submenu (see FIGURE 8-16) allows a site name to be used for
a web page heading. By default, the Site Name is set to Campbell Scientific.
This provides an easy way of confirming that the camera is connected to the
web interface. The Site Name is limited to 32 characters.
Refer to FIGURE 8-17 for the location of the Site Name on the web pages.
38
FIGURE 8-16. Site Name
Page 51
FIGURE 8-17. Location of Site Name
Site Name
CC5MPX Digital Camera
8.4.3.4 Users and Security
The Users/Security submenu (see FIGURE 8-18) allows for setting of security
features in the CC5MPX.
By default, cameras are shipped with the security authentication disabled.
When the Authentication setting is set to Enable, users will be prompted for a
User Name and Password before access is given. By default, one user is set up
with the user name of Admin and the password of 9999. Ensure that a record of
user names and passwords are kept. In the event that this information is lost,
and the camera can no longer be accessed, the settings can be viewed or
changed by connecting the camera to a computer with DevConfig, using the
RS-232 port.
In order to add a user, fill out the ‘Add/Modify Users’ parameters, select the
required authority level, and submit the new user. Once the camera saves the
action, the User List will show the user name and their authority level. The
User name and password must be 4 to 32 characters in length.
Authority Level Access:
• Admin
o Full camera access
o Can create and edit users and disable security
• Operator
o Full camera access
o Only restriction is Security Settings
• Viewer
o Only access to the Live Video homepage and the Memory Card
page is given
o No settings can be changed
o Only read access to the Memory Card is allowed
39
Page 52
CC5MPX Digital Camera
NOTE
FIGURE 8-18. Users and Security Settings
8.4.3.5 Digital I/O
If a user needs to be removed from the User List, this must be done by a user
with Admin access. Remember that any deletion or changes will only be saved
when the Submit button is clicked.
The light and communication power are multiplexed on the same
wire on the connector. If both powers are enabled, the output
remains on from when the start of capture to when the file is
transfer is complete.
The Digital I/O submenu (see FIGURE 8-19) allows the configuration of some
of the camera’s I/O signals.
40
FIGURE 8-19. Digital I/O Settings
Page 53
8.4.3.5.1 External Trigger Input Settings
The External Trigger Input can be configured to active High or active Low.
When set to active High, 0 volts will be the Inactive state and a positive
voltage will be the active state.
The CC5MPX is shipped from the factory by default with a pull-down resistor
connected to the External Trigger Input and the External Trigger is set to active
High. With this default setting, when no signal is applied to the input the
External Trigger is inactive. A positive voltage is required to change to the
active state.
8.4.3.5.2 Light Power Control Settings
The camera can be configured to switch the external +12 V on, based on the
available light in the scene (yellow wire). There are three settings: Not Used,
Active, and Flash Type. Not Used disables the output, while the other two
enable it.
There are future plans to add two different modes of operation, but currently
they operate in the same manner. The light will only come on when capturing
from a self-timed capture or when an external trigger occurs while the camera
is in sleep mode. The light does not turn on for motion detection capture. The
light turns off after the capture is complete.
CC5MPX Digital Camera
8.4.3.5.3 Communication Power Control
The Communication Power Control setting controls the communication
switched power output line on the Power and I/O cable of the CC5MPX
camera.
The switch output is intended to manage the power to a communication device,
such as a cell modem. This is useful in a solar powered site when there is a
need to limit power consumption of communication devices.
This option enables the CC5MPX to supply up to a maximum of 750 mA of
current. The voltage level will be the same as the camera’s input power (i.e., 12
Vdc).
Some modems will require a warm up time or a period of time to register on a
network. The Communication Warm up Time parameter allows an appropriate
time to be entered for this purpose.
8.4.3.5.4 Heater Power Control
The Heater Power Control setting controls the operation of the optional
window defroster. If enabled, the camera will only turn on the heater if the
current internal temperature is below the threshold setting. The temperature
threshold values are limited to –40 to 25 °C.
If the Always On option is selected, the heater will be on whenever the
temperature is below the threshold and the camera is not in a low powered
state.
If Minutes prior to schedule is selected, the camera will wake up prior to any
of the Self Times schedules and turn on the heater if the temperature is below
41
Page 54
CC5MPX Digital Camera
NOTE
8.4.3.6 Update
the threshold settings. This feature does not work with motion detection or
external trigger modes.
This is useful for a remote site that may be prone to riming and frost. A camera
that is setup to take hourly pictures can be configured to turn on the defroster
several minutes prior to the scheduled picture to defrost the window.
The Update I/O submenu (see FIGURE 8-20) provides the ability to update
the firmware in the camera. It is recommended to check for firmware updates
on the Campbell Scientific website to ensure that the camera has the most
recent version of firmware.
Once a file is downloaded, click the Browse button to select the new firmware
update with the ‘tar.gz’ file extension. Once the proper file is selected, click on
Update button and the process will begin.
During the update process DO NOT disconnect power, close web
browser, or navigate away from the Update page. DO NOT extract
the firmware update from the .tar.gz file. This compressed file
must be sent to the CC5MPX in order to update the firmware.
Once the firmware update process is completed, a web page will be displayed
indicating that the process has completed. The camera will reboot itself. It will
take a few minutes for the camera to operate as normally.
The firmware update process normally keeps all configuration settings in the
camera. It is recommended to verify the settings after an update.
FIGURE 8-20. Update Menu
42
Page 55
8.4.3.7 Events
CC5MPX Digital Camera
The Events submenu (see FIGURE 8-21) provides a list of system events. If
the System Status box is red in the Live Video page, the details are logged in
the Events Log. One of the most common recorded events is that the memory
card is properly present after a power up. The message confirms that the
memory card is functioning and it also indicates the size of the memory card.
Other types of event messages and log files include:
• The memory card or the allocated memory is full (when fill and stop
memory management is used).
• Communication and file transfer errors that include:
o FTP
o Email
o PakBus
FIGURE 8-21. Event Logs
43
Page 56
CC5MPX Digital Camera
8.4.3.8 Save/Read Camera Settings
This feature allows for configuration settings to be saved or loaded via the web
interface (FIGURE 8-22). The .xml configuration files are also compatible with
DevConfig.
FIGURE 8-22. Save/Read Camera Settings
8.4.4 Memory Card
Selecting the Memory Card page tab will bring up the Memory Card page (see
FIGURE 8-23) and allow access to the internal SD card.
FIGURE 8-23. Memory Card Page
44
Page 57
CC5MPX Digital Camera
This page shows the size of the memory card loaded in the camera. If no
camera is present, there will be a message stating so, and the view memory
card link and memory card details will not appear.
Each capture event is allocated a limited amount of space on the SD card based
on the settings on the event configuration page. As more space can be allocated
on the event configuration page than is available on the SD card, the camera
will automatically scale the allocated space to fit the SD card. This page shows
the actual space available for each capture event, as well as the space currently
being used.
Click on View Memory Card link to browse the files on the SD card.
FIGURE 8-24. Memory Card Directory Listing
There is a possibility of nine main directories that are created for Image and
Video storage on the camera (FIGURE 8-24). There is a still image and video
directory for each type of capture method and a directory for manually
captured stills. A directory will not be created by the camera if the capture
method is not used.
45
Page 58
CC5MPX Digital Camera
The directory names are:
• ExternTrig1Still
• ExternTrig1Video
• ManualStill
• MotionDetectStill
• MotionDetectVideo
• SelfTimed1Still
• SelfTimed1Video
• SelfTimed2Still
• SelfTimed2Video
Clicking one of the main folders will display the contents; normally another set
of subfolders will be displayed. The camera creates subfolders that are named
by date. The date subfolders can be configured to store images in folders
named either by Year_Month or Year_Month_Day (see FIGURE 8-25).
46
FIGURE 8-25. Data Subfolders
Page 59
CC5MPX Digital Camera
Actual pictures and video will be located in these subfolders and can be viewed
as shown in FIGURE 8-26.
FIGURE 8-26. Example Display of Files
The web interface will display up to 200 files per page. If more files exist in
the directory than at the very bottom of the page, other pages can be selected to
view the additional files (see FIGURE 8-27).
FIGURE 8-27. Example of Multiple Page Viewing
The web interface provides a method of viewing or deleting images and video
from the memory card. It is possible to delete either complete or portions of
directories or subfolders, as well as individual images or videos. Be cautious
when using the Delete All function.
47
Page 60
CC5MPX Digital Camera
8.4.5 Video Settings
Selecting the Video Settings page tab will bring up the Video Settings page (see
FIGURE 8-28). There are two sub tabs that provide two independent types of
video to be recorded.
FIGURE 8-28. Video Settings Page
The video settings consist of the following parameters:
• Banner Position
Three available options are:
o OFF
o Inside Top (FIGURE 8-29)
o Inside Bottom
48
FIGURE 8-29. Video Banner Inside Top with Timestamp and Text
Page 61
CC5MPX Digital Camera
• Name on Image Banner
If YES is selected, text can be entered which would appear in the
video banner. Refer to Section 8.8, PakBus® Communications
for details on how to alter the banner via a PakBus datalogger.
• Include Timestamp in Banner
There are five options for the style of timestamp to include in the
banner text:
o None
o YYYY/MM/DD HH:MM:SS
o MM/DD/YYYY HH:MM:SS
o MM/DD/YYYY HH:MM
o MM/DD/YYYY
• Default File Name
A more meaningful file name can be assigned to the files. The
maximum number of characters is 31. No spaces are allowed within
the file name.
• Count Type
There are three options available:
o None
When using None, the same file will simply be overwritten
on the memory card every time a video is recorded. This may
also happen for the transmitted files that are sent via FTP.
o Number Increment
A unique number is appended to each file name. When the
Number Increment is selected, an additional box will allow a
starting number to be entered. An example of a file name
with the count type is:
Video1_0000001994.avi
o Date and Time
Each file name will have a timestamp appended to it.
Examples of file names with Date and Time option are:
Video1_2011_01_28_14_22_10.avi
Video1_YYYY_MM_DD_HH_MM_SS.avi
(p. 80),
• Resolution/Compression
Currently there are two options for the video capture format; both
options encode the video using MPEG4. The options are 1280 x 720
(720P) or 320 x 240.
• Frame Rate
There are three frame rate options of 30, 15, and 7.5 frames per
second (FPS). Lower frame rates can reduce the file sizes.
The video resolution and frame rate are the two factors that determine the file
size for video files. TABLE 8-6 shows the approximate file size for every
second of recorded video. According to the table, the largest file sizes are
produced by the 720P 30 FPS video, which is 500 kB per second of video. The
smallest video files are produced by the 320 x 240 7.5 FPS video which is 10
kB per second of video.
49
Page 62
CC5MPX Digital Camera
TABLE 8-6. Typical Video File Sizes
CRBasic Example 8-1. Adding GPS Coordinates to the Image Banner
Public sendGps As Boolean
EndProg
Resolution Frames Per Second Kilobytes per Second
7.5 125
720P
1280 x 720
15 250
30 500
7.5 10
320 x 240
15 20
30 65
8.4.5.1 GPS Coordinates
GPS coordinates (CC5MPXGPSLatitude and CC5MPXGPSLongitude) can be
embedded in the image or video files that the camera generates. Two PakBus
variables allow the logger to send the GPS coordinates to the camera, where
they are embedded in the images or video.
The GPS coordinates must be sent as floating point values. Positive latitude
and longitude represent northern and eastern hemispheres, respectively. While
negative values represent southern and western hemispheres, respectively.
Values are not saved through a power cycle, or in OFF mode, but do not need
to be updated every time an image or video is sent.
8.4.5.1.1 Example Program – Adding GPS Coordinates to the Image Banner
The following example illustrates the use of the CC5MPXGPSLatitude and
CC5MPXGPSLongitude instructions, which can be used with CR800 series,
CR1000, or CR3000 dataloggers.
Public gpsLat, gpsLong As Float
Public sendVarResult
BeginProg
sendGps = false
gpsLat = 50.0
gpsLong = -139.0
SerialOpen (Com1,115200,4,0,2000)
Scan (1,Sec,0,0)
If sendGps Then
sendGps = false
SendVariables
(sendVarResult,Com1,0,55,0000,0,"Public","CC5MPXGPSLatitude",gpsLat, 1)
SendVariables
(sendVarResult,Com1,0,55,0000,0,"Public","CC5MPXGPSLongitude",gpsLong, 1)
EndIf
NextScan
50
Page 63
8.4.6 Image Capture
Selecting the Image Capture page tab will bring up the Image Capture settings
page (see FIGURE 8-30). The Image Capture settings are the most significant
settings in determining how the camera will operate.
There are six sub tabs that include:
CC5MPX Digital Camera
• Power Modes
• Self Timed Capture2
• External Trigger
• Motion Detection
• Save/Read Camera Settings
FIGURE 8-30. Image Capture Page
51
Page 64
CC5MPX Digital Camera
8.4.6.1 Power Modes
The Power Modes sub tab (see FIGURE 8-31) allows for selection of the type
of power management that will be used.
FIGURE 8-31. Power Modes
One of the main factors in determining which power mode to use is the power
consumption budget that is available for the camera.
If the camera is operating from an AC main power supply, the camera will
have the best performance characteristics in the Fully On state. On the other
hand, if the camera needs to operate from a battery for long periods of time,
then the OFF state is more suitable. Refer to TABLE 8-7 for the characteristics
of each operating state.
TABLE 8-8, Capture Response Time
(p. 54), shows typical response times from
when a trigger occurs to the time that a picture or video is taken. The OFF state
takes the longest as the main processor is not powered in this state and it must
completely boot up to operate again from the OFF state.
52
Page 65
CC5MPX Digital Camera
TABLE 8-7. Power Modes
Power Mode
Fully On
Partially On
Ethernet Power
Save Mode
Always On
Moderate Power
Save
Full Power Save
Always On
Moderate Power
Save
Operating Characteristics
• Camera is always on.
• Highest power consumption.
• Ethernet is on and always available for incoming communications.
• Not recommended.
• Camera is always on.
• Average power consumption is reduced by 50 mA @ 12 Vdc.
• The Ethernet is normally turned off and is only enabled when
outgoing communications are required (email or FTP).
• User needs to push the Setup button to temporarily enable the
Ethernet port for web page access.
• The camera is effectively off in a low powered state.
• Typical power consumption is 80 mA @ 12 Vdc.
• Ethernet is on and always available for incoming communications.
• The camera will temporarily wake up to the Fully On power mode
when traffic occurs on the network. In situations where there is
constant network traffic, the camera may effectively be in the Fully
On power mode.
• The camera is effectively off in a low powered state.
• Typical power consumption is 80 mA @ 12 Vdc.
• Ethernet is always off.
• Disconnecting and connecting the camera to another Ethernet device
will momentarily wake up the camera to allow it to process
incoming communications. The camera will go into the low powered
mode again if no communications occur.
• The camera is effectively off in a low powered state.
• Average power consumption is typically 10 mA @ 12 Vdc.
• The Ethernet is normally turned off and is only enabled when
Full Power Save
outgoing communications are required (email or FTP).
• User needs to push the Setup button to temporarily enable the
Ethernet port for web page access.
• The camera can respond to RS-232 and RS-485 communication in
this mode.
53
Page 66
CC5MPX Digital Camera
TABLE 8-7. Power Modes
TABLE 8-8. Capture Response Time
NOTE
Power Mode
Deep Sleep
OFF
Ethernet Power
Save Mode
Always On
Moderate Power
Save
Full Power Save
Always On
Moderate Power
Save
Full Power Save
Operating Characteristics
• The Deep Sleep power consumption (6 mA typically) is not affected
by the Ethernet power mode.
• Ethernet, RS-232, and RS-485 communications are non-responsive in
Deep Sleep mode.
• Not recommended.
• The Deep Sleep power consumption (6 mA typically) is not affected
by the Ethernet power mode.
• If Ethernet communications are not used, this can reduce the power
consumption of the camera by 50 mA when the camera exits the
Deep Sleep state.
• The OFF state power consumption (1 mA typically) is not affected by
the Ethernet power mode.
• Ethernet, RS-232, and RS-485 communications are non-responsive
in the OFF state.
• Not recommended.
• The OFF state power consumption (1 mA typically) is not affected by
the Ethernet power mode.
• If Ethernet communications are not used, this can reduce the power
consumption of the camera by 50 mA when the camera exits the
Deep Sleep state.
54
See Section 8.4.2.2, Ethernet Power Mode Settings
settings that influence power consumption.
Power Mode
Typical Capture Time
from Trigger Event
Fully On < 1 second
Partially On 10 seconds
Deep Sleep 15 seconds
OFF 90 seconds
(p. 31), for other
Page 67
8.4.6.2 Self Timed Capture1
The Self Timed Capture1 sub tab (see FIGURE 8-32) is used to configure the
camera to capture still images or video using the internal clock of the
CC5MPX.
CC5MPX Digital Camera
FIGURE 8-32. Self Timed Capture Page
When either of the Self Timed Capture triggers is enabled, the CC5MPX uses
its internal clock as a trigger to initiate the capture of still images or video. In
addition to the Self Timed Capture1, there is also a second independent Self
Timed Capture2. Each configuration is independent of the other, but
overlapping events may delay or prevent one or the other from occurring. For
example, two video recordings or still image captures cannot occur at the same
time.
The first step in setting up the Self Timed Capture is to select the Enable
option for the capture method (see FIGURE 8-33). Once Enable is selected,
parameters for the capture method can be edited.
55
Page 68
CC5MPX Digital Camera
FIGURE 8-33. Enable and Capture Time Values
The Self Timed Capture triggers are set up with the timing relative to
midnight. The first parameter to enter is the Start Minutes relative to midnight.
The Start Minutes parameter is the first occurrence of a capture event after
midnight. If the first timed event is to begin right at midnight, then set this
parameter to zero. If the first timed event is at 7:00 am, then Start Minutes
would be set to 420 as there are 60 minutes per hour, and the start time is 7
hours after midnight (7 hours • 60 minutes/hour = 420 minutes).
Similarly, the Stop Minutes specifies when the capture event is to stop relative
to midnight. Set the Stop Minutes to 0 if there is no stop time. If a stop time
such as 7:00 pm (1900h) is desired, then enter the value of 1140 as there are 60
minutes per hour, and the stop time is 19 hours past midnight (19 hours • 60
minutes/hour = 1140 minutes).
Illustrations of the Start and Stop Times are shown in TABLE 8-9.
56
Page 69
CC5MPX Digital Camera
TABLE 8-9. Start and Stop Time Examples
Start and Stop Time
Settings
Start Minutes = 0
Stop Minutes = 0
Start Minutes = 420
(07:00H)
Stop Minutes = 1140
(19:00H)
Graphical Illustration on a 24 hour Clock
Start Minutes = 1260
(21:00H)
Stop Minutes = 480
(08:00H)
57
Page 70
CC5MPX Digital Camera
TABLE 8-10. Self Time Capture Variables
The Capture Interval is the time between capture events once the Start Minutes
value is reached. For hourly pictures, a value of 60 can be entered. If a value of
0 is entered (not recommended), the Image Interval time will apply to still
images and video of the specified duration will be captured repeatedly.
TABLE 8-10 summarizes all the parameters associated with the Self Timed
Capture.
Variable Allowable Values Description
Self Timed
Capture
• Enable
• Disable
Enables or Disables the Self Timed Capture Trigger.
Start Minutes 0 to 1439 Start time in minutes relative to midnight.
Stop Minutes 0 to 1439 Stop time in minutes relative to midnight.
Capture
Interval
Still Image
Capture
Number of
Images
0 to 1439
• YES
• NO
1 to 60
Image Interval 1 to 60
Capture to
Memory Card
• CARD
• NO
Interval between capture times in minutes. To initiate a
capture interval every 5 min set the variable to 5.
Select YES to include still image captures.
Determines how many still images will be taken when the
capture time is reached.
If the number of images (above parameter) is greater than 1,
this parameter is the time spacing between images.
Selecting CARD enables the still images taken to be stored to
the memory card.
This is the allowable space on the memory card that will be
Maximum
Memory Size
0 to 65535
reserved for Still Images taken by the Self Timed Capture (in
megabytes). A value of 1000 will reserve 1000 MB. A value
of 0 has the camera automatically allocate memory.
There are 2 methods of managing files on the memory card:
• Fill and Stop will stop recording additional images once the
Management
Type Options
• Fill and Stop
• Ring Memory
memory card is full or the allocated memory size is
reached.
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size
is reached.
Still Image
Main Folder
Name
58
Still images for this Self Timed Capture can use 1 of 2
• Setting #1
• Setting #2
Read Only Field
settings. Settings #1 and #2 can be setup with various banner,
resolution and compression values. Refer to Section 8.4.8,
(p. 72).
Still
This is a read only field. The name of the main folder where
the still image files will be stored (SelfTimed1Still).
Page 71
TABLE 8-10. Self Time Capture Variables
Variable Allowable Values Description
An option is given to store images in a subfolder named by
Year_Month or Year_Month_Day. Selecting the
Year_Month_Day option has some performance advantages
Sub Folder
Options
• Year_Month_Day
• Year_Month
when a large number of images are taken. Reducing the
number of files in a folder speeds up the storing and file
management process. Speed advantages are only noticeable if
the number of files in the Year_Month folder will exceed
1000.
CC5MPX Digital Camera
Send via email
Email Still
Image
Send via FTP
FTP Still
Image
Send via
PakBus
PakBus Still
Image
Video Capture
Video Settings
• Disabled
• Email Settings #1
• Email Settings #2
• Setting #1
• Setting #2
• Disabled
• FTP Setting #1
• FTP Setting #2
• Setting #1
• Setting #2
• Disabled
• Enabled
• Setting #1
• Setting #2
• YES
• NO
• Setting #1
• Setting #2
Selecting one of the email settings enables the camera to
transmit the still images via email. The selected email settings
should be properly configured before using the option.
One of the two Still Image settings can be used for the still
images that are sent using the FTP.
Selecting one of the FTP settings enables the camera to
transmit the still images to an FTP server. The selected FTP
settings should be properly configured before using the
option.
One of the two Still Image Settings can be used for the still
images that are sent using FTP.
Used to enable the still images to be sent to PakBus
compatible device. The PakBus settings should be properly
configured in the Communications Page before enabling this
option.
One of the two still image settings can be used for the still
images that are sent using FTP.
Select YES to include Video Capturing.
One of two video settings can be used for video capture.
Duration in
Seconds
Capture to
Memory Card
Maximum
Memory Size
Management
Type Options
0 to 60 The length of time the video is recorded for.
• CARD
• NO
0 to 65535
• Fill and Stop
• Ring Memory
Selecting CARD enables the video taken to be stored to the
memory card.
This is the allowable space on the memory card that will be
reserved for videos taken by the Self Timed Capture (in
megabytes). A value of 1000 will reserve 1000 MB. A value
of 0 has the camera automatically allocate memory.
There are 2 methods of managing files on the memory card:
• Fill and Stop will stop recording additional images once the
memory card is full or the allocated memory size is
reached.
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size
is reached.
59
Page 72
CC5MPX Digital Camera
TABLE 8-10. Self Time Capture Variables
Variable Allowable Values Description
Main Folder
Name
Sub Folder
Options
Read Only Field
• Year_Month_Day
• Year_Month
• Disabled
Send via Email
• Email Settings#1
• Email Settings#2
• Disabled
Send via FTP
• FTP Settings#1
• FTP Settings#2
Send via
PakBus
• Disabled
• Enabled
8.4.6.3 Self Timed Capture2
This is a read only field. The Name of the Main Folder where
the still image files will be stored (SelfTimed1Video).
An option is given to store Videos in a subfolder named by
Year_Month or Year_Month_Day. Selecting the
Year_Month_Day option has some performance advantages
when a large number of Videos are taken. Reducing the
number of files in a folder speeds up the storing and file
management process. Speed advantages are only noticeable if
the number of files in the Year_Month folder will exceed
1000.
Selecting one of the email Settings enables the camera to
transmit the video files via email. The selected email Settings
should be properly configured before using the option.
Selecting one of the FTP settings enables the camera to
transmit the video files to an FTP server. The selected FTP
Settings should be properly configured before using the
option.
Used to enable the video files to be sent to PakBus
compatible device. The PakBus settings should be properly
configured in the Communications Page before enabling this
option.
The settings and parameters are the same as Self Timed Capture1. Refer to
the previous section (Section 8.4.6.2, Self Timed Capture1
8.4.6.4 External Trigger
The External Trigger sub tab (see FIGURE 8-34) is used to configure the
camera to capture still images or video using an external signal that is applied
to the External Trigger input line.
The External Trigger can be configured for an active High signal or an active
Low signal (see Section 8.4.3.5.1, External Trigger Input Settings
capture is triggered by the transition from the inactive state to the active state.
The minimum required pulse period is 10 msec. Preferably pulses should be
short in duration (only a few seconds). The voltage levels are:
Leaving the signal on the External Trigger in the active state will prevent the
camera from entering into a low powered state. If an external device is allowed
to keep the camera in its Fully On state, power consumption will be greatly
affected.
When the camera is Fully On and no other process is taking place, the time
from the transition of the signal from inactive to active, to the time a picture is
(p. 55)).
(p. 41)). The
• Low Level: <0.65 V (–20 Vdc Absolute Min)
• High Level: >2.0 Vdc (+20 Vdc Absolute Max)
60
Page 73
captured or video is started, is typically less than 100 msec. The description of
the parameters for the External Trigger setup is outlined in TABLE 8-11,
External Trigger Variables
(p. 63).
8.4.6.4.1 File Transfer Queuing
When performing multiple captures and transfers off the camera in rapid
succession, the camera will queue file transfers (i.e., send via FTP, then SMTP,
then PakBus). File queueing separates the transfer functions from image and
video capture.
The camera can capture up to five images or videos in parallel with the file
transfers all taking place at the same time. For this feature to work an SD card
must be present.
8.4.6.4.2 External Trigger Video Pre-Recording
Video pre-recording allows the camera to record up to 30 seconds of video
leading up to a related trigger event. This feature can only be used with
external trigger and motion detection capture events.
The external trigger configuration page includes an option labeled Pre-Record
In Seconds. By entering a value between 1 and 30 in this field, the CC5MPX
will begin buffering video in its internal memory. When an event occurs, the
CC5MPX will store the set number of seconds of video to file and then
continue recording the live video until the number of seconds has elapsed.
CC5MPX Digital Camera
The use of pre-recording does impose some limitations on the functionality
available in the CC5MPX:
• The pre-recording feature can only be used when the camera is in the
Fully On power mode.
• If the text banner is enabled in the Video Settings used as part of Pre-
Record configuration, the text banner will be visible in the Live Video
view on the web page.
• If both image capture and video pre-recording are configured for the
same event, the video recording will take precedence. Only once the
video has been recorded and saved or transferred from the camera will
the image capture occur.
61
Page 74
CC5MPX Digital Camera
62
FIGURE 8-34. External Trigger Setup Page
Page 75
CC5MPX Digital Camera
TABLE 8-11. External Trigger Variables
Variable
Allowable Values
Description
Still Image
• YES
Image
If the Number of Images (above parameter) is greater than 1, this
There are 2 methods of managing files on the memory card:
An option is given to store images in a subfolder named by
External
Trigger
Capture
Number of
Images
Interval
Capture to
Memory
Card
Maximum
Memory
Size
Management
Type
Options
Still Image
Main Folder
Name
• Enable
• Disable
• NO
1 to 60
1 to 60
• CARD
• NO
0 to 65535
• Fill and Stop
• Ring Memory
• Setting #1
• Setting #2
Read Only Field
Enables or disables External Trigger capture.
Select YES to include still image captures.
Determines how many still images will be taken when the
External Trigger is activated.
parameter is the time spacing between images.
Selecting CARD enables the still images taken to be stored to the
memory card.
This is the allowable space on the memory card that will be
reserved for Still Images taken by the Self Timed Capture (in
megabytes). A value of 1000 will reserve 1000 MB. A value of 0
has the camera automatically allocate memory.
• Fill and Stop will stop recording additional images once the
memory card is full or the allocated memory size is reached.
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size is
reached.
Still images for this Self Timed Capture can use 1 of 2 settings.
Settings #1 and #2 can be setup with various banner, resolution
and compression values. Refer to Section 8.4.8, Still
(p. 72).
This is a read only field. The Name of the Main Folder where the
still image files will be stored (SelfTimed1Still).
Sub Folder
Options
Send via
Email
Email Still
Image
Send via
FTP
FTP Still
Image
Send via
PakBus
• Year_Month_Day
• Year_Month
• Disabled
• Email Settings #1
• Email Settings #2
• Setting #1
• Setting #2
• Disabled
• FTP Setting #1
• FTP Setting #2
• Setting #1
• Setting #2
• Disabled
• Enabled
Year_Month or Year_Month_Day. Selecting the
Year_Month_Day option has some performance advantages
when a large number of images are taken. Reducing the number
of files in a folder speeds up the storing and file management
process. Speed advantages are only noticeable if the number of
files in the Year_Month folder will exceed 1000.
Selecting one of the email settings enables the camera to transmit
the still images via email. The selected email settings should be
properly configured before using the option.
One of the two Still Image Settings can be used for the still
images that are sent using the email.
Selecting one of the FTP settings enables the camera to transmit
the still images to an FTP server. The selected FTP settings
should be properly configured before using the option.
One of the two Still Image Settings can be used for the still
images that are sent using FTP.
Used to enable the still images to be sent to PakBus compatible
device. The PakBus settings should be properly configured in the
Communications Page before enabling this option.
63
Page 76
CC5MPX Digital Camera
TABLE 8-11. External Trigger Variables
Variable
Allowable Values
Description
Video
• YES
Duration in
This is the allowable space on the memory card that will be
• Disabled
Selecting one of the email Settings enables the camera to
• Disabled
Selecting one of the FTP Settings enables the camera to transmit
PakBus Still
Image
Capture
Video
Settings
Seconds
Pre-Record
in Seconds
Capture to
Memory
Card
Maximum
Memory
Size
Management
Type
Options
Main Folder
Name
Sub Folder
Options
• Setting #1
• Setting #2
• NO
• Setting #1
• Setting #2
0 to 60 The length of time the video is recorded.
0 to 30
• CARD
• NO
0 to 65535
• Fill and Stop
• Ring Memory
Read Only Field
• Year_Month_Day
• Year_Month
One of the two still image settings can be used for the still
images that are sent using FTP.
Select YES to include Video Capturing.
One of two video settings can be used for video capture.
The length of time the video is recorded prior to the external
trigger event. This interval is a portion of the ‘Duration in
Seconds’ interval. It is not in addition to the ‘Duration in
Seconds’ interval
Selecting CARD enables the video taken to be stored to the
memory card
reserved for videos taken by this External Trigger Capture (in
megabytes). A value of 1000 reserves 1000 MB. A value of 0
has the camera automatically allocate memory.
There are 2 methods of managing files on the memory card:
• Fill and Stop will stop recording additional video once the
memory card is full or the allocated memory size is reached
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size is
reached
This is a read only field. The Name of the Main Folder where the
still image files will be stored (ExternTrig1Video).
An option is given to store videos in a subfolder named by
Year_Month or Year_Month_Day. Selecting the
Year_Month_Day option has some performance advantages
when a large number of videos are taken. Reducing the number
of files in a folder speeds up the storing and file management
process. Speed advantages are only noticeable if the number of
files in the Year_Month folder will exceed 1000. If speed is not
an issue, then user preference is fine.
Send via
Email
Send via
FTP
Send via
PakBus
64
• Email Settings#1
• Email Settings#2
• FTP Settings#1
• FTP Settings#2
• Disabled
• Enabled
transmit the video files via email. The selected email Settings
should be properly configured before using the option.
the video files to an FTP server. The selected FTP Settings
should be properly configured before using the option.
Used to enable the video files to be sent to PakBus compatible
device. The PakBus settings should be properly configured in the
Communications Page before enabling this option.
Page 77
8.4.6.5 Motion Detection
The Motion Detection sub tab (see FIGURE 8-35) is used to configure the
camera to capture still images or video using the Motion Detection capability
of the camera. Refer to TABLE 8-12 for a description of each variable.
Even if this feature is enabled, the motion detection will only operate when the
camera is in the Fully On power state.
CC5MPX Digital Camera
FIGURE 8-35. Motion Detection Page
65
Page 78
CC5MPX Digital Camera
8.4.6.5.1 CC5MPX Motion Detection Description
The CC5MPX camera implements an adaptive motion detection scheme in
order to help avoid false motion detection triggers that can occur in normal
outdoor scenes. The adaptive motion detection method automatically adjusts
the motion detection threshold based on the average motion characteristics of a
given scene.
The adaptive motion detection scheme sets its threshold values based on a 20
second moving average of the scene. For example, if a CC5MPX was focused
on a ceiling fan that was off, the CC5MPX motion detection would be
triggered if the fan was turned on. After a period of 20 seconds the motion
detection would no longer be triggered as the continuous motion of the fan
would automatically increase the required motion detection trigger level.
The sensitivity level for motion detection is the only user configurable
parameter for Motion Detection operation. A value of 1 provides the least
sensitive motion detect threshold setting and a value of 99 provides the most
sensitive motion detect threshold setting. Motion detection can be a
complicated feature to implement. It is recommended to begin with a motion
detect threshold setting of 50 and experiment with the performance based on
the application.
If the camera is not detecting motion that is desired, the motion detection
sensitivity level should be increased. If the camera is producing too many false
triggers, then the motion detect level should be decreased. Note that there is
always a probability that the camera can either produce false motion detects or
not detect desirable motion due to too many scene variables. In some cases
where motion detection of a small object is required, it may be necessary to set
a motion detect level that will also produce frequent false triggers.
The adaptive motion detect is a very good method for most applications. One
consideration is that when a continuous level of motion is introduced into a
scene, the motion detection sensitivity decreases. The result is that some
motion may not be detected when a continuous dynamic scene exists. For
example, a person walking through a scene with windblown trees may not
trigger the motion detect capture that would normally be triggered when there
is no wind and the trees are not moving.
Motion Detection Notes:
• If a moving object that requires detection occupies a larger percentage
of the image scene, the motion detection tends to be more reliable.
Zooming in or moving the camera closer to the moving objects helps
improve performance.
• Objects moving slowly within the image scene require a higher
sensitivity setting compared to fast moving objects.
66
• Sudden changing light levels can falsely trigger motion detection.
Sources of false triggers include rapidly changing light levels at
sunrise or sunset, or during the movement of clouds.
• Good lighting of the image scene produces the best results.
Page 79
• The motion detection feature uses the full 4:3 ratio frame to capture
TABLE 8-12. Motion Detection Settings
motion. Still images in the 320 x 176, 640 x 352 and 1280 x 720
formats, and video in the 720p format will crop a portion of the top
and bottom of the image or video.
• Motion detection is paused when video is being recorded.
• The delay from motion occurring to image capture is typically 1
second (2 seconds for a 5 MP image).
8.4.6.5.2 Motion Detection Video Pre-Recording
Video pre-recording allows the camera to record up to 30 seconds of video
leading up to a related trigger event. This feature can only be used with the
external trigger and motion detection capture events.
The Motion Detection configuration page includes an option labeled PreRecord In Seconds. By entering a value between 1 and 30 in this field, the
CC5MPX will begin buffering video in its internal memory. When an event
occurs, the CC5MPX stores a set number of seconds of video to file and then
continues recording the live video until the number of seconds of duration has
elapsed.
CC5MPX Digital Camera
The use of pre-recording does impose some limitations on the functionality
available in the CC5MPX:
• The pre-recording feature can only be used when the camera is in the
Fully On power mode.
• If the text banner is enabled in the Video Settings used as part of Pre-
Record configuration, the text banner will be visible in the Live Video
view on the web page.
• If both image capture and video pre-recording are configured for the
same event, the video recording will take precedence. Only once the
video has been recorded and saved or transferred from the camera will
the image capture occur.
Variable Allowable Values Description
The best method for determining where to set the level is to
experiment with the values. The value of 1 is the least sensitive
value but less prone to false triggers. The value of 99 is the
Sensitivity
Level
1 to 99
most sensitive value, and is most susceptible to false triggers.
It is not necessary to enable the motion detection to test its
functionality. Simply set this parameter and observe the Motion
Detect Status in the Live Video page.
Motion
Detection
• Enable
• Disable
Enables or disables motion detection captures.
67
Page 80
CC5MPX Digital Camera
TABLE 8-12. Motion Detection Settings
Variable Allowable Values Description
Start time in minutes relative to Midnight. The Motion
Start Minutes 0 to 1439
Detection can be set to be active for a certain time period only.
See TABLE 8-9, Start and Stop Time Examples
details.
Stop time in minutes relative to midnight. The Motion
Stop Minutes 0 to 1439
Detection can be set to be active for a certain time period only.
See TABLE 8-9, Start and Stop Time Examples
details.
(p. 57), for more
(p. 57), for more
Still Image
Capture
Number of
Images
• YES
• NO
1 to 60
Image Interval 1 to 60
Capture to
Memory Card
Maximum
Memory Size
Management
Type Options
Still Image
• CARD
• NO
0 to 65535
• Fill and Stop
• Ring Memory
• Setting #1
• Setting #2
Select YES to include still image captures.
Determines how many still images will be taken when the
Motion Detection is activated.
If the Number of Images (above parameter) is greater than 1,
this parameter is the time spacing between images.
Selecting CARD enables the still images taken to be stored to
the memory card.
This is the allowable space on the memory card that will be
reserved for Still Images taken by Motion Detection capture (in
megabytes). A value of 1000 reserves 1000 MB. A value of 0
has the camera automatically allocate the memory.
There are 2 methods of managing files on the memory card:
• Fill and Stop will stop recording additional images once the
memory card is full or the allocated memory size is reached.
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size is
reached.
Still Images for the External Trigger capture can use 1 of 2
settings. Settings #1 and Settings #2 can be setup with various
banner, resolution and compression values.
Main Folder
Name
Sub Folder
Options
Send via
Email
Email Still
Image
68
Read Only Field
This is a read only field. The name of the main folder where
the still image files will be stored (MotionDetectStill).
An option is given to store images in a subfolder named by
Year_Month or Year_Month_Day. Selecting the
• Year_Month_Day
• Year_Month
Year_Month_Day option has some performance advantages
when a large number of images are taken. Reducing the
number of files in a folder speeds up the storing and file
management process. Speed advantages are only noticeable if
the number of files in the Year_Month folder will exceed 1000.
• Disabled
• Email Settings #1
• Email Settings #2
• Setting #1
• Setting #2
Selecting one of the email settings enables the camera to
transmit the still images via email. The selected email settings
should be properly configured before using the option.
One of two still image settings can be used for the still images
that are sent using email.
Page 81
TABLE 8-12. Motion Detection Settings
Variable Allowable Values Description
CC5MPX Digital Camera
Send via FTP
FTP Still
Image
Send via
PakBus
PakBus Still
Image
Video Capture
Video Settings
Duration in
Seconds
Pre-Record in
Seconds
Capture to
Memory Card
• Disabled
• FTP Settings #1
• FTP Settings #2
• Setting #1
• Setting #2
• Disabled
• Enabled
• Setting #1
• Setting #2
• YES
• NO
• Setting #1
• Setting #2
0 to 60 The length of time the video is recorded.
0 to 30
• CARD
• NO
Selecting one of the FTP Settings enables the camera to
transmit the still images to an FTP server. The selected FTP
settings should be properly configured before using the option.
One of the two Still Image settings can be used for the still
images that are sent using FTP.
Used to enable the still images to be sent to PakBus compatible
device. The PakBus settings should be properly configured in
the Communications Page before enabling this option.
One of the two still image settings can be used for the still
images that are sent using FTP.
Select YES to include Video Capturing.
One of two video settings can be used for video capture.
The length of time the video is recorded prior to the external
trigger event. This interval is a portion of the ‘Duration in
Seconds’ interval. It is not in addition to the ‘Duration in
Seconds’ interval.
Selecting CARD enables the video taken to be stored to the
memory card.
Maximum
Memory Size
Management
Type Options
Main Folder
Name
Sub Folder
Options
0 to 65535
• Fill and Stop
• Ring Memory
Read Only Field
• Year_Month_Day
• Year_Month
This is the allowable space on the memory card that will be
reserved for video taken by Motion Detection capture (in
megabytes). A value of 1000 reserves 1000 MB. A value of 0
has the camera automatically allocate the memory.
There are 2 methods of managing files on the memory card:
• Fill and Stop will stop recording additional video once the
memory card is full or the allocated memory size is reached.
• Ring memory management will start deleting the oldest files
once the memory card is full or the allocated memory size is
reached.
This is a read only field. The name of the main folder where
the video files will be stored (MotionDetectVideo).
An option is given to store Video in a subfolder named by
Year_Month or Year_Month_Day. Selecting the
Year_Month_Day option has some performance advantages
when a large number of Videos are taken. Reducing the
number of files in a folder speeds up the storing and file
management process. Speed advantages are only noticeable if
the number of files in the Year_Month folder will exceed 1000.
If speed is not an issue, then user preference is fine.
69
Page 82
CC5MPX Digital Camera
TABLE 8-12. Motion Detection Settings
Variable Allowable Values Description
Send via
Email
Send via FTP
Send via
PakBus
8.4.6.6 Save/Read Camera Settings
• Disabled
• Email Settings#1
• Email Settings#2
• Disabled
• FTP Settings#1
• FTP Settings#2
• Disabled
• Enabled
This feature allows for configuration settings to be saved or loaded via the web
interface (FIGURE 8-36). The .xml configuration files are also compatible with
DevConfig.
Selecting one of the email Settings enables the camera to
transmit the video files via email. The selected email Settings
should be properly configured before using the option.
Selecting one of the FTP Settings enables the camera to
transmit the video files to an FTP server. The selected FTP
Settings should be properly configured before using the option.
Used to enable the video files to be sent to PakBus compatible
device. The PakBus settings should be properly configured in
the Communications Page before enabling this option.
70
FIGURE 8-36. Save/Read Camera Settings
Page 83
8.4.7 Communication Settings
FIGURE 8-37. Communication Settings Page
Communications using the PakBus protocol (FIGURE 8-37) enables remote
retrieval and/or storage of images or video to external devices such as
compatible Campbell Scientific dataloggers. The factory default
communication interface is RS-232. If RS-485 is required, the internal camera
jumpers will need to be changed. See Section 8.5, Internal Jumpers
more details.
CC5MPX Digital Camera
(p. 76), for
Additionally, the PakBus neighbouring address allows for communication with
devices that are several hops away on the PakBus network. See TABLE 8-13
for reference.
71
Page 84
CC5MPX Digital Camera
TABLE 8-13. PakBus Communication Settings
Variable
Allowable
Values
• 115200
• 57600
RS-232 BAUD Rate
• 38400
• 19200
• 9600
• 115200
• 57600
RS-485 BAUD Rate
• 38400
• 19200
• 9600
PakBus Port Read Only
PakBus Address 1 to 4094
PakBus Destination
Address
PakBus Neighbour
Address
1 to 4094
0 to 4094
Description
Select the desired baud rate. Once the baud rate is set, it will always
be fixed. The factory Default Settings is 115200 baud.
Select the desired BAUD rate. Once the baud rate is set, it will
always be fixed. The factory Default Settings is 115200 baud.
This read only value reflects the internal jumper settings of the
camera. It will either read RS-232 or RS-485. See Section 8.5,
Internal Jumpers
(p. 76), if the jumpers need to be changed. This value
cannot be changed in this view.
The desired PakBus address for this camera. The factory default is
55.
The PakBus address of the device the camera will communicate with
or send files to.
Enter the address of the PakBus device physically to connect to the
CC5MPX PakBus communication lines. This allows the neighbour to
relay communication between the CC5MPX and the final destination
for the data.
PakBus
Communication
0 to 16
Delay
PakBus Security
Code
0 to 65535
8.4.8 Still Image Settings
Extra delays may be required for certain communication links, such
as satellite.
The factory default is 0. If a security code is not required by the
PakBus destination device, set this parameter to 0. Otherwise set the
security code as required by the destination service.
Selecting the Still Image Settings page tab brings up the Still Image Settings
page (see FIGURE 8-38). The Still Image settings allows for the configuration
of still images that the camera will take.
There are two sub tabs that include two independent Still Settings:
• Still Settings #1
• Still Settings #2
TABLE 8-14 describes the variables used in the Still Image Settings.
72
Page 85
CC5MPX Digital Camera
TABLE 8-14. Still Image Settings
FIGURE 8-38. Still Images Settings Page
Variable Allowable Values Description
Resolution
Banner
Position
Name on
Image
Banner
Include
Timestamp
in Banner
• 320 x 176
• 320 x 240
• 640 x 352
• 640 x 480
• 1280 x 720
• 1280 x 960
• 2592 x 1944
• OFF
• Inside Top
• Inside Bottom
• Outside Top
• Outside Bottom
• NO
• YES
• NONE
• YYYY/MM/DD/HH/MM/SS
• MM/DD/YYYY HH:MM:SS
• MM/DD/YYYY HH:MM
• MM/DD/YYYY
The resolution option is the resolution of the Still Image in
pixels (width x height).
Selecting the inside banner displays the text within the image
area either at the top or bottom.
The outside banner is a text bar placed above or below the
still image. The vertical height of the picture is increased to
accommodate the outside banner. See TABLE 8-15, Still
Image Resolution Details
(p. 74), for the image sizes with
outside banners.
Be selecting Yes, a custom name can be placed on the Image
Banner. Refer to Section 8.8, PakBus® Communications
80)
, for details on how to alter the Banner via a PakBus
(p.
datalogger. See TABLE 8-15, Still Image Resolution Details
(p. 74), for the number of characters that can fit on a specific
resolution size. The actual text field can hold 255 characters.
A timestamp can be placed on the banner, there are several
options for the format of the date and time to be printed on
the image. For example, the YYYY/MM/DD HH:MM:SS
setting would print a date as: 2014/01/30/ 14:54:07.
Default File
Name
Text Field
This text field allows a file name to be used for the still
images produced. The text is limited to 32 characters.
73
Page 86
CC5MPX Digital Camera
TABLE 8-14. Still Image Settings
TABLE 8-15. Still Image Resolution Details
Variable Allowable Values Description
• The NONE option uses the same file name for all pictures.
Only 1 image name appears in a directory or is transmitted
out (email, FTP, or PakBus).
• The Date and Time option appends a timestamp to the file
name. The text entered in the above parameter (Default
File Name) is followed by the date and time:
<Default File Name>_YYYY_MM_DD_HH_MM_SS.jpg
Count Type
• NONE
• Date and Time
• Number Increment
• The Number Increment option appends a 10-digit counter
to the file name. The files are named with the following
format after the Default File Name text:
<Default File Name>_XXXXXXXXXX.jpg
JPG
Compression
Level
• NONE/Lossless
• Low
• Med
• High
• Very High
The None/Lossless compression level produces the largest
JPEG files with no loss of information. The Very High
compression level produces the smallest file sizes, but there
will be noticeable distortions in the picture due to
compression. See TABLE 8-15, Still Image Resolution
Details
(p. 74), for typical size information.
Resolution
Size with
Outside
Banner
320 x 176 320 x 192 45
Maximum
Characters
in Banner
Compression
Type
Typical
File Size
None/Lossless 32
Low 16
Medium 12
High 8
Very High 6
None/Lossless 40
Low 20
320 x 240 320 x 256 45
640 x 352 640 x 384 64
74
Medium 15
High 10
Very High 8
None/Lossless 120
Low 40
Medium 28
High 20
Very High 16
Page 87
CC5MPX Digital Camera
TABLE 8-15. Still Image Resolution Details
Resolution
Size with
Outside
Banner
Maximum
Characters
in Banner
640 x 480 640 x 512 64
1280 x 720 1280 x 752 98
1280 x 960 1280 x 992 98
Compression
Type
Typical
File Size
None/Lossless 132
Low 48
Medium 32
High 25
Very High 18
None/Lossless 448
Low 128
Medium 75
High 54
Very High 40
None/Lossless 580
Low 164
Medium 96
High 68
2592 x 1944 2592 x 1984 136
8.4.8.1 GPS Coordinates
See Section 8.4.5.1, GPS Coordinates
Program – Adding GPS Coordinates to the Image Banner
GPS coordinates (CC5MPXGPSLatitude and CC5MPXGPSLongitude) can be
embedded in the image or video files that the camera generates. Two PakBus
variables allow the logger to send the GPS coordinates to the camera, where
they are embedded in the images or video.
The GPS coordinates must be sent as floating point values. Positive latitude
and longitude represent northern and eastern hemispheres, respectively. While
negative values represent southern and western hemispheres, respectively.
Values are not saved through a power cycle, or in OFF mode, but do not need
to be updated every time an image or video is sent.
Very High 48
None/Lossless 1900
Low 500
Medium 264
High 190
Very High 150
(p. 50), and Section 8.4.5.1.1, Example
(p. 50).
75
Page 88
CC5MPX Digital Camera
8.4.8.1.1 Example Program – Adding GPS Coordinates to Image Banner
Public sendGps As Boolean
Public gpsLat, gpsLong As Float
public sendVarResult
BeginProg
sendGps = false
gpsLat = 50.0
gpsLong = -139.0
SerialOpen (Com1,115200,4,0,2000)
Scan (1,Sec,0,0)
If sendGps Then
sendGps = false
SendVariables
(sendVarResult,Com1,0,55,0000,0,"Public","CC5MPXGPSLatitude",gpsLat, 1)
SendVariables
(sendVarResult,Com1,0,55,0000,0,"Public","CC5MPXGPSLongitude",gpsLong, 1)
EndIf
NextScan
EndProg
The following example illustrates the use of the CC5MPXGPSLatitude and
CC5MPXGPSLongitude instructions, which can be used with CR800 series,
CR1000, or CR3000 dataloggers.
8.5 Internal Jumpers
There are two sets of jumpers that are internal to the camera. One set is used to
select either RS-232 or RS-485 communications on the Power and I/O cable.
The other set is used to select a pull-up or a pull-down resistor on the External
Trigger input line.
Refer to Section 9.2, Backplate Removal Procedures
remove the backplate to access the internal jumpers of the camera.
8.5.1 RS-232/RS-485 Jumpers
Jumper locations are shown in FIGURE 8-39. There are three jumpers that can
be moved from either the left or the right 2 x 3 jumper posts. When the jumpers
are on the right 2 x 3 jumper posts, the RS-232 output is selected (Factory
Default position). To change the serial output format from RS-232 to RS-485,
move all three jumpers from the right to the 2 x 3 jumper posts located on the
left position. Always move all three jumpers and never install additional
jumpers.
The available communication interfaces can be configured with the cameras
web interface or via DevConfig. RS-232 and RS-485 interfaces can be
configured to a range of baud rates between 9600 and 115200. Both interfaces
support only the PakBus protocol.
(p. 100), for details to
76
Page 89
CC5MPX Digital Camera
SD-Card
Right: Pull Down
Left: Pull Up
RS-232
RS-485
FIGURE 8-39. Internal Jumper Locations
8.5.2 External Trigger Pull-up/Pull-down Jumper
The jumper location for the External Pull-up/Pull-down location is shown in
FIGURE 8-39. When the jumper is located on the right two pins of the header
(factory default position), there is a 100 kΩ pull-down resistor connected from
the External Trigger line to ground. When the jumper is placed on the left two
pins of the header, there is a 47 K pull-up resistor connected from the External
Trigger line to 3.3 Volts.
The pull-up resistor would be useful for having contact closures or open
collector output signals trigger the camera. In the case of a contact closure, the
jumper would be moved to the pull-up position and then 1 end of the contact
would connect to the External Trigger signal and the other end of the contact
would connect to ground. A schematic representation is shown in FIGURE
8-40.
77
Page 90
CC5MPX Digital Camera
Can be RS-232
8.6 RS-232 Communications
FIGURE 8-40. Schematic Showing External Contact Device
The RS-232 serial communications are used with the camera for two purposes:
to configure and setup the camera using Device Configuration Utility software
that Campbell Scientific provides; to send image files from the camera to other
devices using PakBus.
or RS-485
Check the PakBus Port value under Communications Settings to confirm the
camera has internal jumpers configured to RS-232 or RS-485 (see FIGURE
8-41).
FIGURE 8-41. Serial PakBus Port Setting
The CC5MPX Power and I/O port is configured by default to provide a 3-wire
RS-232 connection (TX, RX, Ground). The wires can be terminated directly on
the control ports of a compatible datalogger. For connection to a computer
9-pin serial port, use the DB9 Female to Terminal Block Adaptor (pn 28840),
which facilitates the connection of the cable pigtail end to a computer 9-pin
78
Page 91
CC5MPX Digital Camera
serial port. The adaptor comes with the CC5MPX as an accessory. See
FIGURE 8-42.
FIGURE 8-42. Connecting the CC5MPX to a 9-Pin RS-232 Port
An illustration of the required RS-232 connections to a datalogger is shown in
FIGURE 8-43.
FIGURE 8-43. Datalogger Connections with RS-232
8.7 RS-485 Communications
The optional RS-485 communication interface of the CC5MPX can be used in
conjunction with the MD485 to interface a datalogger to one or more cameras.
Refer to the MD485 Manual for additional information.
79
Page 92
CC5MPX Digital Camera
Set for RS-485
The MD485 is useful for connecting more than one camera to a datalogger or if
long cable lengths are involved. If multiple cameras are connected to an
MD485, then it would be beneficial to offset the capture times of the images so
that only one camera is attempting to transmit a file at any given time.
The camera can download images or video via an RS-485 port using PakBus.
An MD485 is required to interface the camera to a datalogger. The following
items are required for RS-485 PakBus communications and can be confirmed
by either the web interface of DevConfig (FIGURE 8-44):
• Confirm that the PakBus port parameter of the Communications
Setting is reading RS-485.
• Set the RS-485 baud rate to match the baud rate of the device being
connected to the camera.
• Set the parameter PakBus Address of Communication Settings to a
unique value in the PakBus network.
• Set the parameter PakBus Destination Address of the device that the
camera needs to send images to.
• Include PakBus Security Code, as required.
FIGURE 8-44. RS-485 Shown in PakBus Port Setting
8.8 PakBus® Communications
80
The camera uses PakBus to send image files from the camera to the datalogger
or other PakBus compatible devices. The LoggerNet tool PakBus Graph can
be used to change the configuration of a camera. The use of the PakBus
Graph is discussed in Section 8.8.2, PakBus Graph Operations
the LoggerNet literature or software for more details.
(p. 81). Refer to
Page 93
PakBus can also be used to control specific operational parameters, transfer
variables or text between the datalogger and camera. When an image or video
file is ready to be transmitted, the camera will initiate communications and
send the image or video via the selected serial interface.
The CC5MPX is capable of producing video files that exceed 30 MB in size.
Trying to send such a large file to a datalogger using PakBus can be
problematic. For this reason, the CC5MPX is setup to not send any files using
PakBus that are larger than 2 MB.
The camera is a PakBus lead node and is not capable of performing any
routing. However, the CC5MPX has the ability to communicate with devices
that are several hops away on the PakBus network.
8.8.1 Concurrent PakBus Communications
PakBus allows the camera to download images to a datalogger simultaneously
with other datalogger communications. A communications task will take longer
if the datalogger is communicating with multiple devices at the same time.
It may be beneficial to set up the system to avoid image transfers when other
communications are scheduled.
CC5MPX Digital Camera
For example, longer connect times on long distance telephone connections can
be avoided by scheduling image transfers from the camera to the datalogger
outside the scheduled data collection time. If a station is called on the hour to
retrieve data, image acquisitions could be initiated before the scheduled call
(15 minutes prior) to shorten the connect times.
8.8.2 PakBus Graph Operations
The CC5MPX supports configuration via PakBus Graph over the serial port.
A datalogger or other type of PakBus relay device is required to interface
PakBus Graph to the camera.
8.8.2.1 Datalogger Settings
The datalogger must be configured as a router (i.e., Is Router must be set to
TRUE) and the camera PakBus address must be in the list of allowed
neighbours for the datalogger port used. The camera and the datalogger must
be set to use the same baud rate to communicate properly.
8.8.2.2 Discovery
After starting PakBus Graph, the camera may not be visible immediately. To
discover the camera, right click on the green box marked as [4094] in the
graph and click Search for Neighbours. This will open the Search for
Neighbours dialog box, press Start and the graph should display all the devices
within the PakBus network.
8.8.2.3 Power Modes
The camera has several low power modes. The CC5MPX cannot respond to
PakBus communications while the camera is in the low power mode, such as
OFF or Deep Sleep. PakBus communications will wake up the camera if it is
set for Partially On mode. Using the low power mode with the Ethernet power
81
Page 94
CC5MPX Digital Camera
8.8.3 PakBus Variable Control
mode set to Full Power Save will allow the camera to respond almost
immediately (less than 10 seconds).
The external trigger can also be utilized to wake up the camera and enter high
powered mode. As long as the external trigger is held high, the camera will
remain in the high powered mode. Lowering the external trigger signal will
allow the camera to enter a low powered operating mode again.
The camera is capable of receiving variables, commands, or text from a
datalogger. The specific operational parameters that can be altered or
controlled include:
• Still Image Banners
• Video Banners
• Camera Window Defroster
• Camera Shutdown
The use of the Send Variable instruction allows the datalogger to transfer
values or text that can be used in the image or video banners. The Send
Variable instruction is used to toggle the camera window defroster on/off or to
safely shut the camera down.
To update the Banner information with values from a datalogger the variable is
a String, and must be limited to 255 characters (including null terminator).
The camera variable names are:
• CC5MPXStillBanner1
• CC5MPXStillBanner2
• CC5MPXVideoBanner1
• CC5MPXVideoBanner2
The variable for controlling the window defroster is numeric and needs to be
declared as a Long in CRBasic. The variable for controlling camera power is a
Boolean, which needs to be declared in CRBasic. The names of the camera
variables are:
• CC5MPXDefroster
• CC5MPXShutdown
8.8.3.1 PakBus Control of Window Defroster Function
PakBus will temporarily (one shot) override the existing window defroster
control state. Users are advised to only use one type of control to avoid
unexpected operation of the defroster. Options include the Automatic mode set
via the web page or DevConfig, or PakBus SendVariables command.
To turn on the defroster, the numeric value should be set to a non-zero value
(i.e., 1). To turn the defroster off, the value should be set to zero. When a nonzero value is sent to the camera, the heater will turn on and a 65 second
countdown timer will start. After 65 seconds, the defroster will automatically
turn off (this should override settings already in place). If an additional nonzero is sent before the defroster is turned off, then the timer will be reset to zero
and will begin the countdown again.
82
Page 95
The defroster commands should be sent to the camera every 60 seconds or
CRBasic Example 8-2. SendVariable Instruction
EndIf
more to ensure continuous operation.
The defroster will be allowed to turn on only once for 65 seconds at internal
temperatures between 25 and 50 °C. This flag will only be reset again once the
internal temperature drops below 25 °C, or the camera is reset. Full, continuous
operation is only allowed at temperatures of 25 °C or less. At internal
temperatures above 50 °C, the defroster will not turn on.
8.8.3.2 PakBus Control of CC5MPX Power
The ability to shut down the camera safely using a PakBus command is
available in the CC5MPX. By writing a value of 1 (or any value not equaling
zero) to the public Boolean variable CC5MPXShutdown, the camera initiates a
shutdown. The shutdown process can take up to 30 seconds. The camera will
turn back on after 10 minutes, or can be externally triggered.
Following is an example of the CRBasic command that will shut down a
camera with PakBus address 55:
SendVariables (SendVarResult,Com1,0,55,0000,400, “Public”, “CC5MPXShutdown”,1,1)
8.8.3.3 Example Program – SendVariable Instruction
CC5MPX Digital Camera
The following example illustrates the use of the SendVariable instruction to
alter Still Image Banner #2, as well as toggle the camera window defroster.
'CR1000 Series Datalogger
'Declare Public Variables
Public PTemp, batt_volt
Public TurnDefrosterOn As Boolean
Public TurnDefrosterVal As Long
Public SendVarResult As Long
Public BannerString As String * 60
Public tempstring As String * 60
'Define Data Tables
Data(Test,1,-1)
DataInterval (0,60,Sec,10)
Minimum (1,batt_volt,FP2,0,False)
Sample (1,PTemp,FP2)
EndTable
'Main Program
BeginProg
SerialOpen (Com1,115200,4,0,2000)
Scan (10,Sec,0,0)
PanelTemp (PTemp,250)
Battery (batt_volt)
'Enter other measurement instructions
tempstring = FormatFloat(PTemp,"%2.2f")
BannerString = "Panel Temp " + tempstring
If TimeIntoInterval (0,5,Min) Then
SendVariables
(SendVarResult,Com1,0,55,0000,400,"Public","CC5MPXStillBanner2",BannerString,1)
83
Page 96
CC5MPX Digital Camera
EndProg
If TurnDefrosterOn = true Then
TurnDefrosterVal = 1
SendVariables
(SendVarResult,Com1,0,55,0000,200,"Public","CC5MPXDefroster",TurnDefrosterVal,1)
TurnDefrosterOn = false
EndIf
CallTest
NextScan
8.8.4 PakBus Neighbouring Address
The PakBus protocol allows devices to relay data in a network. The CC5MPX
now has the ability to communicate with devices that are several hops away on
the PakBus network. To configure this new feature, a setting has been added to
the PakBus configuration screen on the web page.
Entering the address of the PakBus device physically connected to the
CC5MPX PakBus communication lines, allows the neighbour to relay
communication between the CC5MPX and the final destination for data. Leave
PakBus set to zero (0) if device is directly connected to the final destination.
8.9 Device Configuration Utility
DevConfig can be used to change settings in the CC5MPX. DevConfig
software can be downloaded at no charge from the Campbell Scientific
website.
Using DevConfig:
• Connect the camera to the serial port of a PC using the DB9
FEMALE to Terminal Block Adaptor, as shown in Section 8.6, RS-
232 Communications
• Once the camera is powered up (this can typically take 90 seconds),
the LED must begin to flash. If the LED does not flash, press the
Setup button to exit the camera from a low powered mode.
• Select the CC5MPX from the device list (see FIGURE 8-45) and
connect to the camera.
• Normally the camera is set to 115200 baud. If the camera’s baud rate
is set to a different baud rate, select the appropriate value in the
Device Configuration drop-down list.
• Once connected to the CC5MPX, use the tabs (see FIGURE 8-46) to
navigate and configure the camera.
(p. 78).
84
Page 97
CC5MPX Digital Camera
FIGURE 8-45. CC5MPX Device Configuration Option
FIGURE 8-46. Device Configuration Utility Screen
85
Page 98
CC5MPX Digital Camera
8.10 Image Quality
8.10.1 Night Time Images
8.11 Lens
Lighting conditions have the greatest influence on image quality. The
CC5MPX camera produces the best images under normal daylight conditions.
Pictures taken in good daylight conditions produce crisper and brighter images,
as the camera uses the entire image to adjust the exposure settings of a scene.
Scenes that contain small variations in light intensities will produce better
exposed images. In scenes with high variations in light intensities, such as a
bright sky or a dark horizon, the image may contain portions that are underexposed and portions that are over-exposed, as with most cameras. The
CC5MPX utilizes various techniques to produce an overall good picture under
most lighting conditions.
In general, the camera does not produce good images at night. If lighting is
present, such as street lights, then distinguishable pictures can be taken.
The standard and zoom lenses for the CC5MPX contain the following features:
• C-Type Mount
• Varifocal (manual zoom)
• Manual Focus
• DC Iris
Access to the lens for adjusting the zoom and focus requires the removal of the
CC5MPX lens tube (see FIGURE 8-47). The lens tube is threaded on and
needs to be turned counter clockwise to be removed.
The zoom and focus adjustments are shown in FIGURE 8-48. The
thumbscrews may need to be loosened prior to moving the adjustments. It is
important to tighten the thumb screws once the camera focus and zoom
adjustments are completed, to avoid problems from vibration.
The camera controls the iris of the lens using the cable with a 4-pin connector.
This connector must always be plugged into the receptacle (on the front lens
plate of the camera) for proper operation.
86
Page 99
FIGURE 8-47. CC5MPX Lens Tube Removal
CC5MPX Digital Camera
FIGURE 8-48. Zoom and Focus Adjustments
8.11.1 Camera Lens and Field of View
The CC5MPX includes a 4-12 mm lens, which provides an approximate 27°
horizontal field of view when fully zoomed in, and an 80° horizontal field of
view when fully zoomed out.
The CC5MPX-Z camera includes a 10-40 mm lens, which provides an
approximate 9° horizontal field of view when fully zoomed in, and a 35°
horizontal field of view when fully zoomed out.
See FIGURE 8-49 for a visual representation of the field of view.
87
Page 100
CC5MPX Digital Camera
FIGURE 8-49. CC5MPX Horizontal Field of View
FIGURE 8-50. Field of View – Fisheye Lens
(A) The lens on the CC5MPXFE can see 5 degrees more than the 185 degrees.
(B) The lens on the CC5MPXFE can be adjusted to any value between 94 and
185 degrees.
8.11.2 Focus and Zoom Adjustment
To facilitate the focus and zoom adjustment, a network connection will need to
be established with the camera to view the live video on a web browser.
88
Refer to Section 4, QuickStart
Web Browser Interface
(p. 2), and Section 8.4, Camera Operation using
(p. 25), for details on accessing the camera with a web
browser.
If the LED is not flashing while the camera is wired up and the power is turned
on, it may be necessary to press the Setup button to wake the camera from any
of its low powered modes. In some configurations, pressing the Setup button
may also be required to enable the Ethernet port.
Loading...