Page 1
FT-120 Andalusia Fountain
Assembly Instructions
Fountain Information:
• Professional installation is recommended for this fountain!
• This fountain holds approximately 60 gallons of water.
• This fountain does not t under a Campania fountain cover.
• Compatible with #10 Rell Device and LED kits
• No stoppers are required to use the rell kit or LED kit for this fountain.
Pump Information:
OEMPF320 - 320 GPH Pump (16 ft. cord length)
Tools Required:
Bubble Level
Screwdriver
Caulking Gun
Hammer
Proudly
MADE IN USA
Fountain Components
Image Item Description
Andalusia
Fountain Water
Feature
Andalusia
Fountain
Pump House
Andalusia
Fountain
Basin
Andalusia
Fountain
Pipe Cap
Component
Item #
FT-120A 1
FT-120B 1
FT-120C 1
FT-
120CAP
Quantity
Pump Kit Parts List
Image Component Quantity
PK300 Pump
(use adapter indicated)
LED-LIGHT 1
LED-CORD 1
LED-TRANS 1
2
#5 wing nut drain stopper 1
#7 wing nut drain stopper 1
Approx. 20" length of 1/2" black
non-kink tubing
Approx. 2" length of 5/8" clear vinyl
tubing
Approx. 2" length of 1/2" CPVC pipe 1
Approx. 42" length of 1/2" galvanized
pipe
1
1
1
2
10 oz. tube of silicone 1
Wedges 2
Hose Clamp 1
rev 3/30/2020
Page 2
FT-120 Andalusia Fountain
Assembly Instructions
Professional installation is recommended for this fountain!
Fountain Set-Up:
Assembly & Installation - A fountain can be difcult to install without knowing and understanding the steps involved. To ensure your fountain is
installed properly, please read our instructions and tips before you begin.
Step 1 - Seek Professional Help: Check if professional installation is recommended for your fountain.
Step 2 - Check Foundation: Place your fountain on a level surface. It is recommended to place your fountain on concrete or a hard packed
Step 3 - Create a Drip Loop: To prevent water from dripping down the cord and damaging the electrical socket, create a drip loop by allowing
Step 4 - Use a GFCI Outlet: Use only a GFCI outlet when running a fountain.
FT-120C (1080 lbs)
56.25"L x 30"W x 17.5"H
gravel pad. If the base is level but some components seem off, rotate components or use wedges to level them.
the pump power cord to fall below the wall outlet.
Assemble your fountain on a level surface capable of holding a minimum of 2200 lbs with an
approximate 13.5 sq. ft. footprint (actual dimensions 56" x 29.75").
Step 1 - Place the base (FT-120C) into position where the fountain will be installed, ensuring that
it is level.
Step 2 - Using a caulking gun, run a bead of silicone along the top of the basin (FT-120C) where
the water feature (FT-120A) will be placed. Take care not to use too much silicone to
minimize oozing of silicone from between the pieces.
FT-120A (532 lbs)
55"L x 16"W x 38"H
Step 3 - Place the water feature (FT-120A) on top of the basin (FT-120C) making sure that the PVC
pipe holes are lined up between the top of the basin and the bottom of the water feature.
NOTE - BE CAREFUL NOT TO PINCH FINGERS WHEN LOWERING! Hand holds have been
molded into the water feature for easier assembly.
Step 4 - Clean off any excess silicone with your nger or a dry rag as quickly as possible.
Step 5 - Using a hammer, gently tap the 2" length of CPVC pipe into the PVC coupling in the
bottom of the water feature (FT-120A).
Note: To prevent breakage, do not do this step early.
Step 6 - Place the #5 drain stopper into the hole at the bottom of the bowl on the water feature
(FT-120A).
Step 7 - Drop the support pipes into the holes at the top of the water feature (FT-120A).
7a - Check that the pipes have dropped all the way through the water feature (FT-120A)
AND basin (FT-120C) before going forward.
Step 8 - Insert the stone caps (FT-120CAP) into the holes over the pipes.
Note: The caps are removable.
(2) FT-120CAP (>1 lbs)
1"L x 1"W x 1"H
Page 3
FT-120B (37 lbs)
13"L x 7.5"W x 15.25"H
FT-120 Andalusia Fountain
Assembly Instructions
Step 9 - Assemble the pump kit:
9a - Using a hose clamp, attach the 1/2" black tubing to the pump outlet.
Step 10 - Place the pump and LED light in the fountain and feed the cords through the hole
between the basin (FT-120C) and water feature (FT-120A).
10a - Attach the LED light to the transformer outside of the fountain.
Step 11 - Fit the 5/8" clear end of tubing assembly over the CPVC installed into the water feature
(FT-120A) in step 5.
Step 12 - Place the pump cover (FT-120B) over the pump along the back of the basin.
Step 13 - Place the #7 drain stopper into the hole at the bottom front of the basin.
Step 14 - Place LED light in the front of the basin aiming the light at the waterfall.
Step 15 - Let the fountain sit 24 hours before lling it with water.
Page 4
Maintenance:
Pump Care - The fountain relies heavily on the quality of the pump. A well-maintained pump can last several years.
Step 1 - Fully submerge: Ensure the pump is fully submerged at all times to avoid damage.
Step2-Ensurewaterlevelissufcient:Check water levels regularly as water may evaporate over time, and periodically change water to avoid algae
Step 3 - Clean pump: Use soap and water, or white vinegar and water, with a small, soft brush to clean the pump of debris, dirt, and algae buildup.
Surface Care - Paints and nishes may fade over time due to weathering. By following these tips, you will be able to maintain your fountain’s surface.
Step 1 - Control Algae and White Scale: Due to water evaporation, you may see white residue on your fountain surface from the mineral content in
Step2-ProtectandRenish: Depending on the material of your fountain, protectants and sprays may prolong the appearance of the surface. Paint and
Winter Care - Many materials used to produce fountains can expand and contract in different temperatures/humidity levels. If the temperature falls below
32°F or humidity levels change drastically, follow the steps below to protect your fountain.
Step 1 - Bring inside: If possible, bring your outdoor fountain inside for the winter.
Step 2 - Store in dry location: If unable to bring inside, store your fountain in a dry and covered location.
Step 3 - Bring components inside: Move all internal components (stoppers, tubing, lights, pump, etc) inside. A pump can stay in a fountain for the
Step 4 - Completely drain: It is important to prevent water from accumulating anywhere, as freezing and thawing of water can cause pump damage
Step 5 - Elevate Fountain: Fountains may freeze to the ground and cause cracking in the base if left outside in the winter. If unable to store inside or in
Step 6 - Cover Fountain: Make sure to use a breathable material when covering. DO NOT COVER IN PLASTIC! Make sure the fountain is taut so that
buildup.
This should be done every 2-3 months.
your water supply. Algaecides and cleansers can help prevent buildup that occurs from minerals and hard water.
renishing kits can be used for touch-up.
winter, but if you choose to leave it in, it must be completely dry and insulated with plastic bags and towel to ensure it stays dry. However it is
recommended to bring it inside.
and cause cracks to form in your fountain. Remove the drain plugs.
a dry covered location, try to raise your fountain above ground.
no snow or water can pool in the cover. Tie the opening at the bottom of the cover around the fountain.
Troubleshooting:
Pump Not Working - When operating the pump for the rst time, it can take a few minutes before water begins to ow properly. If it is still not working after
a few minutes, please follow our troubleshooting tips below. Before troubleshooting, UNPLUG YOUR PUMP.
Step 1 - Submerge Pump: Ensure your pump is fully submerged in water at all times to avoid pump damage.
Step 2 - Manual Check: If the pump cover is removable, try removing the cover to access the impeller area. Turn the rotor to ensure it is not broken or
Pump Noise - Some sound from the pump may be normal, but you can follow these tips to reduce sound or resolve abnormal noises.
Step 1 - Submerge Pump: Ensure your pump is fully submerged at all times and clean of debris, dirt and algae buildup.
Step 2 - Check Location: You may hear the vibration of the pump touching the side walls of the fountain. Make sure the pump is only touching the bottom.
Step 3 - Check Flow Rate: Too low of a ow rate might cause spews or burps.
Water Flow Rate - Some fountains come with a dial or valve to adjust the ow rate, but if you do not have this option or if you are still unsatised with your
ow rate after changing the settings, check out our tips below.
Step 1 - Adjust the Water Level: Insufcient water levels can affect water intake by the pump. Check the fountain instructions to ensure the appropriate
Step 2 - Check for Kinks: Check to make sure the tubing is not kinked. Kinks in the tubing can slow or halt the ow of water.
Step 3 - Clamp the Hose: To slow the water ow, try clamping the hose with a hose clamp or zip-tie.
Splashing - Having trouble with splashing? Some splashing is inevitable, especially when you rst turn on your fountain, but if you are experiencing
excessive splashing, try our troubleshooting tips below.
Step 1 - Adjust the Water Level: Ensure the pump is fully submerged, but avoid overlling your fountain.
Step 2 - Flow Rate: If your pump includes a dial or valve to adjust the ow rate, try changing the settings to see if it affects splashing. If your pump is
Step 3 - Adjust Position: Try arranging stones or placing a splash guard, at the fountain base. You can also place a screen in the basin.
jammed.
water capacity for your fountain.
not adjustable, check our Flow Rate section to learn about other ways to change the ow rate.
Leaking - If your fountain is leaking, check these quick tips on how to x it.
Step 1 - Adjust the Water Level: Your fountain may leak if it is too full.
Step 2 - Check Tubing: Check that the tubing is attached completely and correctly.
Step 3 - Check Stopper: Ensure stopper is completely seated in the fountain. You can also use 100% pure clear silicone to ensure a proper seal is achieved
Step 4 - Cracking: Your fountain may be cracked from improper winter care; see Winter Care in Maintenance Tips.
Loading...