CamOne COIN26 User guide [ml]

Page 1
turn on video & images
Surf Mount 360°
Anleitung
Manual
Page 2
turn on video & images
Lieferumfang
Überprüfen Sie die Vollständigkeit, bevor Sie das Surf Mount Set montieren.
» Platte A, B und C » 1 Sicherungsband mit Gewinde für die DiveBox » 2 Klebepads mit Aussparungen für die Platten A und C » 1 rundes Klebepad für Platte B » 1 rundes Moosgummi-Pad
Komponente
Platte A Hauptplatte B Platte C
Page 3
Einsatzbereiche
1
360°
turn on video & images
[1] – Die Verwendung des Moosgummi­Pads bietet Ihnen die Möglichkeit, Platte B des Surf Mount Sets und somit die Kamera um 360° zu drehen. So kann auch während der Aufnahme geschwenkt werden.
2
3
B C
A
[2] – Für die feste Verklebung verwenden Sie die Platten B und C. Diese werden mithilfe der 3M Klebepads auf dem Board befestigt, wobei Platte C als zusätzliche Sicherung der Kamera fungiert.
[3] – Für die Verschraubung am Bodyboard verwenden Sie die Platten A und B. Bohren Sie dazu Löcher in das Board, die denen des Surf Mount
B
Sets entsprechen. Verschrauben sie anschließend Platte B von der Oberseite des Boards mit Platte A auf der Unterseite, um sicheren Halt zu haben. Hierzu benötigen Sie Schrauben (Durchmesser: 7 mm; Länge: Dicke des Boards + 15 mm), selbstsichernde Muttern, sowie Unterlegscheiben (nicht im Set enthalten).
3
Page 4
turn on video & images
Vorbereitung bei Verkleben
1
B
B
B1
B2
Entscheiden Sie zuerst, wie Sie das Surf Mount Set verwenden möchten.
Um Platte B als drehbares Element verwenden zu können, folgen Sie bitte den Schritten 2 – 7. Möchten Sie die
B2
Platten B und C fest auf dem Board
B1
verkleben, folgen Sie bitte den Schritten 8 – 10 in der Anleitung.
! Bevor Sie mit der Montage beginnen, befreien Sie bitte sowohl das Board als auch die
einzelnen Platten des Surf Mount Sets von Fett und sonstigen Schmutzablagerungen. Verwenden Sie dazu ein geeignetes Reinigungsmittel.
2
Ziehen Sie zunächst die helle Schutzfolie des 3M Klebepads ab.
4
3
Kleben Sie nun das 3M Pad auf Platte A des Surf Mounts.
5
Wiederholen Sie die Schritte 2 und 3 für Platte C.
Ziehen Sie die Schutzfolie von der Rückseite des Moosgummi-Pads (B1) ab.
4
Page 5
turn on video & images
6
Befestigen Sie das Moosgummi-Pad auf Platte B des Surf Mounts.
8
Ziehen Sie zunächst die helle Schutzfolie des 3M Klebepads (B2) ab.
10
Wiederholen Sie die Schritte 8 und 9 für Platte C.
7
Kleben Sie nun Platte A auf das Board, stecken Sie anschließend Platte B mit der Nut an die Führung von Platte A. Befestigen Sie nun Platte C auf dem Board – achten Sie auch hier wieder darauf, dass Nut und Führung ordnungsgemäß ineinandergreifen.
9
Kleben Sie nun das 3M Pad auf Platte B des Surf Mount Sets.
! Kleben Sie die Platten B und C nun vorsichtig auf das Board - achten Sie
dabei darauf, dass die Führung von Platte C ordnungsgemäß in der Nut von Platte B sitzt.
Für die Befestigung der CamOne innity legen Sie die
Kamera in die DiveBox ein. Stellen Sie sicher, dass die Dichtung der DiveBox unbeschädigt und voll funktionsfähig ist. Verschließen Sie die DiveBox sorgfältig. Schrauben Sie dann das Sicherungsband mit dem Gewinde in das Stativgewinde der DiveBox. Verbinden Sie anschließend die DiveBox mit dem M-Halter und schieben Sie diesen auf die dafür vorgesehenen Schienen auf Platte B. Sichern Sie nun die Kamera zusätzlich, indem Sie das Sicherungsband mit einem festen Knoten an Platte C befestigen.
5
Page 6
turn on video & images
Technische Daten
Durchmesser: 100 mm, je Platte Gesamtlänge (Platte A+B+C) 260 mm Gewicht: 131 g, inkl. Verpackung Material: Kunststoff
Zubehör
Art.-Nr.: EAN Artikel
FCHD02 4260033049520 FlyCamOne HD externer Bildschirm 2,5 Zoll (63,5 mm) FCHD03 4260033049537 FlyCamOne HD 5.8 GHz Video Transmission Set COIN08 4260033041975 CamOne innity Ersatzakku LiPo 3,7 V 800mAh COIN10 4260033041968 CamOne innity LinX Digital Video-System 2,4 GHz COIN11 4260033041975 CamOne innity DiveBox COIN12 4260033041982 CamOne innity Lenkerhalter COIN13 4260033041999 CamOne innity Ten-2-Ten Adapter COIN14 4260033042545 CamOne innity Verbinder 1x lang / 1x kurz COIN16 4260033042569 CamOne innity M-Halter COIN17 4260033042576 CamOne innity Helmhalter COIN18 4260033042583 CamOne innity Universalhalterung ach COIN09 4260033041951 CamOne innity Universalhalterung gebogen COIN19 4260033042590 CamOne innity Klebepad klein 5x COIN20 4260033042606 CamOne innity Klebepad groß 5x COIN21 4260033042613 CamOne innity USB-AV Kabel COIN32 4260033042828 CamOne innity 96° Linse COIN31 4260033042811 CamOne innity 142° Linse COIN22 4260033042620 CamOne innity 170° Linse COIN23 4260033042637 CamOne innity Linsenkappe COIN25 4260033042750 CamOne innity Stabstativ COIN28 4260033042781 CamOne innity Chest Mount COIN26 4260033042767 CamOne innity Surfmount 360° COIN27 4260033042774 CamOne innity Wi Module COIN29 4260033042798 CamOne innity Release Button COIN30 4260033042804 CamOne innity Bullet Time Cable FCHD15 4260033049650 FlyCamOne HD GPS-Modul mit X-Kabel FCHD16 4260033049667 FCHD Rapid Rush 16GB Micro SD-Speicherkarte FCHD32 4260033049827 FCHD Rapid Rush 32GB Micro SD-Speicherkarte FCHD43 4260033048578 USB Steckernetzteil 110-220V (Laden über die Steckdose)
6
Page 7
turn on video & images
Sicherheitshinweise
Lesen Sie vor Gebrauch genau die Bedienungsanleitung und die Sicherheitshinweise.
Hiermit erklären wir, dass dieses Modell den grundlegenden Anforderungen und
den anderen relevanten Vorschriften der Richtlinie 2004/108/EG entspricht.
Eine Kopie der Konformitätserklärung kann unter der Adresse (S. 7) angefordert werden.
Gewährleistung & Garantie
Dem Verbraucher wir unbeschadet seiner Mängelansprüche gegenüber dem Verkäufer eine Haltbarkeitsgarantie zu den nachstehenden Bedingungen eingeräumt:
» Neugeräte und deren Komponenten, die aufgrund von Fabrikations- und/oder
Materialfehlern innerhalb von 24 Monate ab Kauf einen Defekt aufweisen, werden von CamOneTec nach eigener Wahl gegen ein dem Stand der Technik entsprechendes Gerät kostenlos ausgetauscht oder repariert. Für Verschleißteile (z. B. Akkus, Gehäuse usw.) gilt diese Haltbarkeitsgarantie für 3 Monate ab Kauf.
» Diese Garantie gilt nicht, soweit der Defekt der Geräte oder der Gegenstände auf
unsachgemäßer Behandlung und/oder Nichtbeachtung der Anleitung beruht.
» Garantieansprüche sind sofort nach Kenntnis des Garantiefalles geltend zu machen. » Ersetzte Geräte bzw. deren Komponenten, die im Rahmen des Austauschs an CamOneTec
zurückgeliefert werden, gehen in das Eigentum von CamOneTec über. » Durch eine erbrachte Garantieleistung verlängert sich der Garantiezeitraum nicht. » Soweit kein Garantiefall vorliegt, behält sich CamOneTec vor, dem Kunden den Austausch,
die Reparatur oder die Versandkosten in Rechnung zu stellen. Der Kunde wird hierüber
vorab informiert.
Service & Support
CamOneTec by ACME CamOneTec by ACME (ab Oktober 2012) Industriestr. 10a Boikweg 24 33397 Rietberg 33129 Delbrück Germany Germany
Telefon: +49 5244 7000 70 (bis Oktober 2012) E-Mail: service@camonetec.com
camonetec.com
Eine Liste der weltweiten Service-Stationen erhalten Sie über camonetec.com/service
7
Page 8
turn on video & images
Content
! Please check whether the set is complete before using the Surf Mount 360°.
» Plates A, B and C » 1 safety band with thread for the DiveBox » 2 adhesive pads with notches for plates A and C » 1 round 3M adhesive pad for plate B » 1 round foam rubber pad
Components
Plate A Master Plate B Plate C
Page 9
Range of use
360°
turn on video & images
1
[1] – Using the foam rubber pad enables you to turn plate A, and thus the camera, by 360°. That way, you can pan while
lming.
2
3
B C
A
[2] – To securely stick the Surf Mount Set to the board, use plates B and C. These are stuck to the board by using the 3M adhesive pads, whereas plate C works as an additional support for the camera.
[3] – To screw the Surf Mount Set to a bodyboard, use plates A and B. For that purpose, drill holes into the board, matching the ones on the Surf Mount
B
Set. Afterwards, screw plate B from the top against plate A from the bottom of the board to achieve maximum hold. To do so, you need screws (diameter: 7 mm; length: thickness of board + 15 mm) and inherently safe nuts as well as washers (not included in the set).
9
Page 10
turn on video & images
Preparations
1
B
B
B1
B2
First, decide on how you want to use the Surf Mount Set. In order to use plate B as a rotatable element follow steps 2 –
7. If you intend to stick plates B and C to the board follow steps 8 – 10 of the
B2
instruction.
B1
! ! Before tting the Surf Mount Set clean all grease and other dirt off the board and the
plates. Use suitable cleaning supplies.
2
Start by removing the light protective foil from the cut-out 3M adhesive pad.
4
3
Stick the 3M pad to plate A.
5
Repeat steps 2 and 3 for plate C.
Remove the protective foil from the foam rubber pad (B1).
10
Page 11
turn on video & images
6
Stick the foam rubber pad onto plate B.
8
Remove the light protective foil from
the 3M adhesive pad (B2).
10
Repeat steps 8 and 9 for plate C.
7
Now, stick plate A to the board. Attach plate B’s groove to plate A’s tongue. Afterwards, stick plate C to the board – make sure, that tongue and groove are tightly connected in order to prevent plate B from falling off!
9
Stick the 3M pad to plate B.
! ! Carefully stick plates B and C to the board – make sure that plate C’s tongue
is correctly inserted into plate B’s groove.
In order to attach the CamOne innity put the camera
into the DiveBox. Make sure the DiveBox’s seal is undamaged and fully operational. Close the DiveBox carefully. Now, screw the safety band’s thread into the DiveBox’s tripod socket. Afterwards, connect the DiveBox with the M- Mount and slide it into the intended rail on plate B. To ensure the camera is secure, tie the safety band tightly to plate C.
11
Page 12
turn on video & images
Technical data
Diameter: 100 mm each plate Total length (plate A+B+C) 260 mm Weight: 131 g, incl. packaging Material: plastics
Accessories
Art.-Nr.: EAN Article
COIN08 4260033041975 CamOne innity Battery LiPo 3,7 V 800mAh COIN10 4260033041968 CamOne innity LinX Digital Video-System 2,4 GHz COIN11 4260033041975 CamOne innity DiveBox COIN12 4260033041982 CamOne innity Handlebar Mount COIN13 4260033041999 CamOne innity Ten-2-Ten Adaptor COIN14 4260033042545 CamOne innity Connector 1x long / 1x short COIN16 4260033042569 CamOne innity M-Mount COIN17 4260033042576 CamOne innity Helmet Mount COIN18 4260033042583 CamOne innity Flat Mount COIN09 4260033041951 CamOne innity Curved Mount COIN19 4260033042590 CamOne innity Adhesive Pad small 5x COIN20 4260033042606 CamOne innity Adhesive Pad big 5x COIN21 4260033042613 CamOne innity USB-AV Cable COIN32 4260033042828 CamOne innity Lens 96° COIN31 4260033042811 CamOne innity Lens 142° COIN22 4260033042620 CamOne innity Lens 170° COIN23 4260033042637 CamOne innity Lens cap COIN25 4260033042750 CamOne innity Mono pod COIN26 4260033042767 CamOne innity Surfmount 360° COIN28 4260033042781 CamOne innity Chest Mount COIN27 4260033042774 CamOne innity Wi Module COIN29 4260033042798 CamOne innity Release Button COIN30 4260033042804 CamOne innity Bullet Time Cable FCHD02 4260033049520 FlyCamOne HD externeral screen 2,5” (63,5 mm) FCHD03 4260033049537 FlyCamOne HD 5.8 GHz Video Transmission Set FCHD15 4260033049650 FlyCamOne HD GPS-Module with X-Cable FCHD16 4260033049667 FCHD Rapid Rush 16 GB Micro SD-Memory card FCHD32 4260033049827 FCHD Rapid Rush 32 GB Micro SD-Memory card FCHD43 4260033048578 USB Power adaptor 110-220 V (Charging with socket)
12
Page 13
turn on video & images
Safety Advice
Before you start using the camera please read the manual and safety advices carefully.
Herewith we declare that this item is in accordance with the essential requirements
and other relevant regulations of the directive 2004/108/EC. A copy of the original
declaration of conformity can be obtained at the address below.
Service & Support
from October 2012
CamOneTec by ACME CamOneTec by ACME
Industriestr. 10a Boikweg 24 33397 Rietberg 33129 Delbrück Germany Germany
Phone: +49 5244 7000 70 (until October 2012) E-Mail: service@camonetec.com
camonetec.com
A list of worldwide service stations is available at camonetec.com/service
13
Page 14
CamOneTec.com
Loading...