Regulatory notes and statements
FCC Radio Frequency Exposure statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance.
We declare that the product is limited in CH1~CH11 by specified firmware
controlled in the USA.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
i
Export restrictions
This product or software contains encryption code that may not be exported or
transferred from the US of Canada without an approved US Department of
Commerce export license.
Safety Information
Your device contains a low power transmitter. When device is transmitted it sends
out radio frequency (RF) signal.
CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this
equipment should be installed and operated with minimum distance 20cm between
the radiator and your body. Use on the supplied antenna. Unauthorized antenna,
modification, or attachments could damage the transmitter and may violate FCC
regulations.
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are
considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article
3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489 17 and EN 55024 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328 has been conducted. These are
considered relevant and sufficient.
CE in which Countries where the product may be used freely:
Overview of this User’s Guide......................................................................................................................................................................1
Unpacking and Setup..........................................................................................................................................................................................2
LED Indicator.................................................................................................................................................................................................3
Check the installation.....................................................................................................................................................................................3
Windows 98se/ME/2000/XP Utility and Driver Installation......................................................................................................................4
Congratulations on your purchase of this Thumb Size IEEE 802.11g Wireless LAN
USB 2.0 Adapter.
This manual helps to get familiar with the Thumb Size IEEE 802.11g Wireless
LAN USB 2.0 Adapter. This manual contains detailed instructions in operation of
this product. Please keep this manual for future reference.
With a Wireless LAN (IEEE 802.11g) USB 2.0 Adapter, a desktop or laptop
computer can communicate with another computer in a wireless way. Easy-to-use
utilities are bundled with Wireless USB Adapter for configuration, monitoring, and
diagnosis purposes.
The Thumb Size 802.11g Wireless LAN USB 2.0 Adapter can wirelessly transmit
and receive data, minimizing the need for wired connections, at a speed of up to
fifty-four megabit per second.
The Thumb Size 802.11g Wireless LAN USB 2.0 Adapter provides users with an
access to real-time information anywhere in their organization. The mobility
provides productivity and service, which are not available under wired networks.
The Thumb Size 802.11g Wireless LAN USB 2.0 Adapter configuration is easy to
change from peer-to-peer networks, suitable for a small number of users, to full
infrastructure networks of thousands of users that allow roaming around a broad
area.
Overview of this User’s Guide
Introduction. Describes the Thumb Size 802.11g Wireless LAN USB 2.0
Adapter and its features.
Unpacking and Setup. Helps you get started with the basic installation of the
Thumb Size 802.11g Wireless LAN USB 2.0 Adapter.
Hardware Installation. Describes the LED indicators of the Adapter.
Software Installation. Tells how to setup the driver and the utility setting.
Technical Specifications. Lists the technical specifications of the Thumb Size
802.11g Wireless LAN USB 2.0 Adapter.
1
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.