Cameo Communications WLAG1302 User Manual

802.11a/b/g

mini PCI Adapter

CAMEO WLAG-1302 User’s Guide

Regulatory notes and statements
Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generate, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and

2) The antenna should be integral if the end device is intended to be operated in

5.15 ~ 5.25GHz frequency range.
As long as 2 conditions above are met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).

i

IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID can not be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization. The availability of some specific channels
and/or operational frequency bands are country dependent and are firmware
programmed at the factory to match the intended destination. The firmware setting
is not accessible by the end user.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users (for
example: Notebook, etc.). The final end product must be labeled in a visible area
with the following: “Contains TX FCC ID: NHPWLAG1302”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.

The users manual for OEM integrators end users must include the following
information in a prominent location “IMPORTANT NOTE: To comply with FCC
RF exposure compliance requirements, the antenna used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or
transmitter”.

If the end product integrating this module is going to be operated in 5.15 ~

5.25GHz frequency range, the warning statement in the user manual of the end
product should include the restriction of operating this device in indoor could void
the user’s authority to operate the equipment.

This product is limited in CH1-CH11 for 2.4G band by specific firmware controlled
by the manufacturer and is not user changeable. The antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter. The availability of some specific channels and/or operational
frequency bands are country dependent and are firmware programmed at the
factory to match the intended destination. The firmware setting is not accessible by
the end user.

ii

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

Protection requirements for health and safety – Article 3.1a

Testing for electric safety according to EN 60950 has been conducted. These are
considered relevant and sufficient.

Protection requirements for electromagnetic compatibility – Article

3.1b

Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489­17 and EN 55024 has been conducted. These are considered relevant and sufficient.

Effective use of the radio spectrum – Article 3.2

Testing for radio test suites according to EN 300 328 has been conducted. These are
considered relevant and sufficient.

CE in which Countries where the product may be used freely:

Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland,
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.

France: except the channel 10 through 13, law prohibits the use of other channels.

使用本產品之系統製造商請於設備上標示本產品內含射頻模組:

XXXyyyLPDzzzz-x"

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得

擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現
象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依
電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。

工作頻率 5.250 ~ 5.350GHz該頻段限於室內使用

iii

iv

TABLE OF CONTENT

Introduction.........................................................................................1

Overview of this User’s Guide........................................................1

Software Installation...........................................................................2

Windows 98se/ME/2000/XP Utility and Driver Installation.........2

Wireless Utility Setting....................................................................4

Technical Specifications ..................................................................14

v

INTRODUCTION

Congratulations on your purchase of this 802.11a/b/g mini-PCI Adapter.
This manual helps to get familiar with the Wireless mini PCI Adapter. This manual

contains detailed instructions in operation of this product. Please keep this manual
for future reference.

With a the 802.11a/b/g mini PCI Adapter, a desktop or laptop computer can
communicate with another computer in a wireless way. Easy-to-use utilities are
bundled with Wireless mini-PCI Adapter for configuration, monitoring, and
diagnosis purposes.

Wireless mini PCI Adapter can wirelessly transmit and receive data, minimizing the
need for wired connections, at a speed of up to fifty-four megabit per second.

Wireless mini PCI Adapter provides users with an access to real-time information
anywhere in their organization. The mobility provides productivity and service,
which are not available under wired networks. The Wireless mini PCI Adapter
configuration is easy to change from peer-to-peer networks, suitable for a small
number of users, to full infrastructure networks of thousands of users that allow
roaming around a broad area.

Overview of this User’s Guide

Introduction. Describes the Wireless mini PCI Adapter and its features.
Software Installation. Tells how to setup the driver and the utility setting.
Technical Specifications. Lists the technical (general, physical and environmental)

specifications of the Wireless mini PCI Adapter.

1