CAME 001DC011AC, 001CS1PLCO, 001DC002AC, 001DC02EARY Installation Manual
10
11
7
2
–
–
+
001DC011AC
001DC002AC
001DC011AC
001DC02EARY
001CS1PLCO
INSTALLATION MANUAL
001CK0009
001CK0012 FR-001CK0013 FR
EN
English
FA00959-EN
AUDIO ENTRY KIT
Ø60
503
a
B
A
C
Page 2 - Manual FA00959-EN - vers. 1
- 10/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
General Notes
• Read the instructions carefully before beginning the installation and carry
out the actions as specied by the manufacturer.
• The installation, programming, commissioning and maintenance of the
product must only be carried out by qualied technicians, properly trained
in compliance with the regulations in force, including health and safety
measures and the disposal of packaging.
• The installer must ensure that the information for the user, where there is
any, is provided and delivered.
• Before carrying out any cleaning or maintenance operation, disconnect the
devices from the power supply.
• The equipment must only be used for the purpose for which it was
expressly designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
eventuali danni derivanti da usi impropri, erronei ed irragionevoli.
This product complies with the relevant directives in force.
Decommissioning and disposal. Dispose of the packaging and the device
at the end of its life cycle responsibly, in compliance with the laws in force
in the country where the product is used. The recyclable components are
marked with a symbol and the material's ID marker.
The data and information shown in this manual are to be considered as
subject to change at any time and without the need for any advance warning.
Measurements, unless otherwise indicated, are in millimetres.
001DC02EARY
Installation
Open the unit by pressing the lever on the back A.
Remove the casing from the back of the unit.
Attach the back of the unit to a wall box using the screws provided Ba
B. The box must be installed at a suitable height for the user. Do not
over-tighten the screws.
Once connections have been completed, re-assemble the casing to the
back of the unit C.
D
– +
– +
B
B
AL
M1
SW3
SW3
M1
a
Page 3 - Manual FA00959-EN - vers. 1
- 10/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
Technical features
Type
001DC02EARY
Power supply from BUS [V DC]
15÷20
Consumption max [mA] 30
Consumption in stand by [mA] <0,5
Single LED consumption [mA]
1
Storage temperature [°C] -25 ÷ +70
Operating temperature [°C] +5 ÷ +40
IP Rating [IP]
30
Features D
Terminal board a
B BUS line input
+
Doorbell
–
Call attenuated
SW3 SW3
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
... beep!
A x5
a
g
c
f
e
h
i
Page 4 - Manual FA00959-EN - vers. 1
- 10/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
4- Programming the number of rings
Press button as many times as you want the call to ring (from 1 to 6 rings) h.
Three seconds after the button is last pressed, the selected call is played back with the
chosen number of rings.
To exit programming, hang up the handset i.
☞ See the entry panel documentation for call programming.
3- Programming the melody associated with a call from the floor
To listen to the melodies in sequence, press button e.
To select the melody and exit programming, hang up the handset f.
To select the melody and continue with programming, press button g.
2- Programming the melody associated with a call from the entry panel
To listen to the melodies in sequence, press the button .
To select the melody and exit programming, hang up the handset c.
To select the melody and continue with programming, press the button .
1-Entering programming mode
Lift up the handset and press button A 5 times in 5 seconds.
A short beep conrms that you have entered programming mode a.
Melody setting
☞ All the programming stages described below must be carried out in sequence:
A
43,5
45
7,5
57
70
106
A
43,5
45
7,5
57
M2M1
+–
a
Page 5 - Manual FA00959-EN - vers. 1
- 10/2017- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.
001DC002AC
Installation
The power supplier must ALWAYS be installed horizontally. The device can be
installed on a DIN rail (EN 50022) in an appropriate electric panel.
NOTE. Proper ventilation is required if the power supplier is installed in a
metal container.
Technical features
Type
001DC002AC
Power supply [V AC] 230
Max current demand [A AC]
0,2
Max energy dissipation [W] 10
Nominal power supply [V DC] 18
Nominal current demand [A DC]
1 for 1’
Nominal current demand [A DC] 0.5 for 3’
Storage temperature [°C] -25 ÷ +70
Operating temperature [°C]
0 ÷ +35
IP Rating [IP] 30
Features A
Terminal board a
~
Mains
~
Terminal board
–
+
Power supply 18 VDC (*)
(*) The appliance is electronically protected against overloads and short
circuits.
Loading...