Camden Door Controls CM-9600-3, CM-9600-3F, CM-9600-3S, CM-9600-7, CM-9600-7F User Manual

CM-9600

Series

5502 Timberlea Blvd., Mississauga, ON L4W-2T7
Telephone: [phone] Fax: [phone]
Toll-Free: 1-877-226-3369
Web: www.camdencontrols.com

Section 1 __________________
General Description

Camden CM-9600 series is a vandal resistant,
illuminated exit switch incorporating a 40 second timer.
The heavy duty stainless steel faceplate is designed to
mount, depending on the model, into a single gang or
narrow jamb electrical box.

The large round 1 inch diameter button is easy to push
and can be activated while wearing gloves. Illumination
and relay power is 12 to 24 V DC.

This unit has been designed specifically to control
automatic doors, electric strikes and mag locks.

The unit is jumper selectable to show the relay ON or
OFF status, with user selectable options for red, green
or no illumination. User selectable N/O and N/C contacts
are available

Installation Instructions

PAGE 1 OF 2

Section 3 _________________
Technical Data

Model CM-9600 & 9610

Illumination Color None, Red, Green

Operating Temp. -40F to +160F

-40C to +70C

Size Single Gang 4.5”h x 2.75”w x 1.5”d

Narrow Jamb 4.5”h x 1.75”w x 1.5”d

Mounting 2 x #6-32 machine screws

Operating voltage 12 to 24V DC

Time Delay 1 - 40 seconds

Contact Rating 2 amps @ 30V DC

1/2amp @ 125V AC

Section 2__________________
Installation

Wiring

This unit will operate on 12 to 24 VDC, with no jumper
change required. For convenience it may be powered
by the same power that supplies the magnetic lock or
electric strike. The same pair of Red & Black wires
connect to 12 to 24 VDC and supply power for the timer,
and the LEDs.

Relay activation is wired through the N/O and/or N/C
terminals shown on the diagram on page 2. When used
with Camden's InVision32 access control system (or
most others) the adjustable time delay is the best choice
for contacts. DC power to the maglock is sent to the N/C
side of contacts to ensure the maglock unlocks when the
switch button is pushed. At the same time the N/O
contact signals the InVision32 of a request to exit so it is
logged in history.

Contact Life 200,000+ @ rated capacity

Section 4_________________
Warranty

Camden Door Controls Inc. guarantees the
CM9600 series to be free from manufacturing defects
for lifetime. It may be returned to our factory where it
will be repaired or replaced (at our discretion) without
charge. Except as stated herein, Camden extends no
warranties expressed or implied regarding function,
performance or service.

Questions?

Call us toll-free at 1-877-226-3369

Filename: CM-9600 Instructions.doc
Revision: 11/5/07 13:47 a11/p11

SAFE position the relay is
normally ON and will turn OFF
when the Piezo button is
pressed or there is a loss of
power.

place as indicated on the
diagram the red LEDs are
on in stand-by and the
green LEDs turn on when
the relay is on. To
reverse the color
sequence move the left
jumper up and the right
jumper down. To turn off
the red LED, remove the
right jumper. To turn off
the green LED, remove
the left jumper.

Input: 12-24V DC
Current Draw: 60mA Active, LEDs ON

40mA Active, LEDs OFF

On Time: 1 – 40 seconds adjustable

When the jumper is in the FAIL

With the jumpers * in

CM-9600 Series

Rear View

Controlling The LEDs Remotely

Remove the jumper(s) * and connect the
middle pin to GND. The right pin will
control the red LED and the left pin will
control the green LED.