Camden Door Controls CM-57GR-1, CM-57GR-2, CM-57GR-2AL, CM-57GR-2AR, CM-57GR-3 Installation Instructions
...
Aura™ CM-57GR
Flush Mount Illuminated Enclosure
Installation Instructions
PACKAGE CONTENTS
1
CM-57
1
Green/Red Aura PCB
1
Dry wall Bracket
2
8-32 x 1 1/2” Screws
2
#6 x 3/8” Screws
Section 1
General Description
Camden Aura™, Model CM-57GR provide the Industry’s
1st “Changing State” illuminated switch enclosures.
They offer eld selectable green/red illumination, activated
directly by the switch or remotely by a relay* such as our CX-33
or EMF-2, a time-clock or access control system.
User selectable features include a 3 Amp Form C relay, and
piezo speaker for audible annunciation, as well as control over
the idle and active LED colours.
Another exclusive is the ability to plug in a TX-9 RF transmitter,
thereby requiring only 2 conductors be run for power
(& no batteries required) !!
The box is made of impact and ame resistant black ABS, and
compatible with any Camden CM-41, CM-45, or CM-46 series
switch.
The illumination is provided by an array of super-bright and
energy efcient LED’s, which can be powered by 12 or 24
volts AC/DC.
Setup
Switch Position Description
SPEAKER On to enable operation of
1
SW1
Colour selection is made with Switch SW2.
You rst chose the Idle colour – Red, or Green, or off, and
then the Active colour – Red, or Green, or off.
Switch Position Description
SW2
If dipswitches 1 & 2 are both OFF, then no illumination will be
present in idle state. Likewise, if both dipswitches 3 & 4 are both
OFF, then no illumination will be present in the active state.
Once all dipswitches are set, proceed to Section 3 - Installation.
2
3
4 Not used
1 ON = Red LED when Idle.
2 ON = Green LED when Idle
3 ON = Red LED when Active
4 ON = Green LED when Active
the speaker with activation of the
push button
RELAY On to enable operation of the
relay with activation of the push button
REMOTE / LOCAL On to enable LED
colour change from idle to Active with
press of the push button.
Section 2
Setup
Switch SW1 contains a bank of 4 dipswitches.
Dipswitch #1 turns the speaker on or off. Dipswitch #2 toggles
operation of the relay, and #3 allows you to choose whether
the colour will be changed locally via the push switch, or
remotely. (Dipswitch #4 is not used at this time)
*Note: The CX-22 Washroom relay may be used with
the Aura™, however an isolating relay must be wired
in parallel with the lock, and the relay’s dry contact
output wired into the CM-57GR.
Page 1 of 5
Section 3
Installation
NOTE: If you will be including the optional Aura™ signage, follow
that product’s installation instructions before installing Aura™.
1. Assemble the drywall clamp to the box as per diagram 1.
Determine the wire access location and drill hole of sufcient
size, or use center knock-out plug.
2. Using the template, cut a hole in the drywall. Pull the wiring
through the access hole and push the box through until the
drywall clamp is on the back of the drywall. Tighten the 8-32
screws until the box is rmly mounted.
3. Remove circuit board from package and locate into the box
(orientation - you should be able to read the writing next to
the terminal strips and dip switches). Pull the wire through
the hole in the centre of the circuit board, and then secure
with the two small self-tapping screws (provided).
Aura™ CM-57GR Flush Mount Illuminated Enclosure Installation Instructions
CX-EL8000 & CX-EL8000L Electronic Cabinet Lock
4.a Wire as per diagram 2 (typical installation). Route the
switch wiring through opaque diffuser panel, and install
diffuser panel into box. It should t snuggly.
4.b If using a TX-9 transmitter to send the signal to an
RX-91 or RX-92 Receiver, attach the transmitter and wire
it before installing circuit board into the enclosure and
tting diffuser. See Diagram 3.
5. Screw in two #6-32 Allen-head screws (provided with
switch) into the threaded center inserts, then attach wires
to switch and install switch over screws. Using the Allen
key (provided), locate the screws and tighten (by hand
only).
6. Re-connect power and test for proper operation.
Section 4
Technical Data
Model CM-57GR
Dimensions 6 1/2” H x 6 1/2” W x 2” D
(165 mm x 165 mm x 51 mm)
Construction Flame-resistant black ABS
(Insert – translucent ABS)
Finish Attractive pebble nish
Mounting 4 x #12 wood screws with anchors
Input Voltage 12 or 24V AC/DC
Output Voltage 3 Volts DC for TX-9 (only)
Current draw 150 mA (max)
Sounder 3200 ± 300 Hz @ 85 dB
Lumina Red: 14.8 lumens, 1600 mW;
Green: 3.8 lumens, 330 mW,
Relay Contact 1 x Form C
Contact Rating 3A @ 30 VDC
Section 5
Warranty
Camden Door Controls guarantees the Aura™ (CM-57GR series)
to be free from manufacturing defects for 3 years from date
of sale.
If, during the rst 3 years, the Aura™ fails to perform correctly,
it may be returned to our factory where it will be repaired or
replaced (at our discretion) without charge. Except as stated
herein, Camden extends no warranties expressed or implied
regarding function, performance or service.
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
DISCOVER THE BEST IN DOOR ACTIVATING
AND LOCKING PRODUCTS!
www.camdencontrols.com
Toll Free: 1.877.226.3369
Page 2 of 5
File: CM-57GR Manual. indd Rev1
Revised: 15/07/2016
Part No: 40-82B197
Loading...