Camden Door Controls CM-55i-1, CM-55i-2, CM-55i-2AL, CM-55i-2AR, CM-55i-3 Installation Instructions
...
Aura™ CM-55i
Flush Mount Illuminated Enclosure
Installation Instructions
PACKAGE CONTENTS
1
CM-55i
1
Blue/Green/Red Aura PCB
1
Dry wall Bracket
2
8-32 x 1 1/2” Screws
2
#6 x 3/8” Screws
Section 1
General Description
Camden Aura™, Model CM-55i provide the Industry’s 1st
“Changing State” illuminated switch enclosures.
They offer eld selectable blue/green/red illumination,
activated directly by the switch or remotely by a relay*
such as our CX-33 or EMF-2, a time-clock or access control
system.
User selectable features include a 3 Amp Form C relay, and
piezo speaker for audible annunciation, as well as control
over the idle and active LED colours.
Another exclusive is the ability to plug in a TX-9 RF
transmitter, thereby requiring only 2 conductors be run for
power (& no batteries required) !!
The box is made of impact and ame resistant black ABS,
and compatible with any Camden CM-41, CM-45, or CM-46
series switch.
The illumination is provided by an array of super-bright and
energy efcient LED’s, which can be powered by 12 or 24
volts AC/DC.
Section 2
Setup
Switch Position Description
REMOTE / LOCAL On to enable LED
1
SW1
Color selection is made with Switches SW2 and SW3. SW2
determines the Active colour and SW3 determines the Idle
color.
2
3
colour change from idle to Active with
press of the push button.
RELAY On to enable operation of the
relay with activation of the push button
SPEAKER On to enable operation of
the speaker with activation of the
push button
Setting the Active Color (SW2)
Switch Position Description
1 ON = Green LED when Active
SW2
2 ON = Red LED when Active
3 ON = Blue LED when Active
Setting the Active Color (SW3)
Switch Position Description
1 ON = Green LED when IDLE
SW3
2 ON = Red LED when IDLE
3 ON = Blue LED when IDLE
Setup
Switch SW1 contains a bank of 3 dipswitches.
Dipswitch # 3 turns the speaker on or off. Dipswitch # 2
toggles operation of the relay, and # 1 allows you to choose
whether the colour will be changed locally via the push
switch, or remotely.
*Note: The CX-22 Washroom relay may be used with
the Aura™, however an isolating relay must be wired
in parallel with the lock, and the relay’s dry contact
output wired into the CM-55i .
Page 1 of 5
Note: If all DIP switches are in the OFF position,
there will be no color illuminated. This allows for no
Idle color or no Active color.
Once all DIP switches are set, proceed to Section 3 – Installation
Section 3
Installation
NOTE: If you will be including the optional Aura™ signage,
follow that product’s installation instructions before installing
Aura™.
Aura™ CM-55i Flush Mount Illuminated Enclosure Installation Instructions
1. Assemble the drywall clamp to the box as per diagram
1. Determine the wire access location and drill hole of
sufcient size, or use center knock-out plug.
2. Using the template, cut a hole in the drywall. Pull the
wiring through the access hole and push the box through
until the drywall clamp is on the back of the drywall.
Tighten the 8-32 screws until the box is rmly mounted.
3. Remove circuit board from package and locate into the
box Pull the wire through the hole in the centre of the
circuit board, and then secure with the two small selftapping screws (provided).
4.a Wire as per diagram 2 (typical installation). Route the
switch wiring through opaque diffuser panel, and install
diffuser panel into box. It should t snuggly.
4.b If using a TX-9 transmitter to send the signal to an
RX-91 or RX-92 Receiver, attach the transmitter and wire
it before installing circuit board into the enclosure and
tting diffuser. See Diagram 3.
5. Screw in two #6-32 Allen-head screws (provided with
switch) into the threaded center inserts, then attach wires
to switch and install switch over screws. Using the Allen key
(provided), locate the screws and tighten (by hand only).
6. Re-connect power and test for proper operation.
Section 4
Section 5
Warranty
Camden Door Controls guarantees the Aura™ (CM-55i series)
to be free from manufacturing defects for 3 years from date
of sale.
If, during the rst 3 years, the Aura™ fails to perform correctly,
it may be returned to our factory where it will be repaired or
replaced (at our discretion) without charge. Except as stated
herein, Camden extends no warranties expressed or implied
regarding function, performance or service.
Technical Data
Model CM-55i
Dimensions 6 1/2” H x 6 1/2” W x 2” D
(165 mm x 165 mm x 51 mm)
Construction Flame-resistant black ABS
(Insert – translucent ABS)
Finish Attractive pebble nish
Mounting 4 x #12 wood screws with anchors
Input Voltage 12 or 24V AC/DC
Output Voltage 3 Volts DC for TX-9 (only)
Current draw 150 mA (max)
Sounder 3200 ± 300 Hz @ 85 dB
Lumina Red: 14.8 lumens, 1600 mW;
Green: 3.8 lumens, 330 mW,
Relay Contact 1 x Form C
Contact Rating 3A @ 30 VDC
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
DISCOVER THE BEST IN DOOR ACTIVATING
AND LOCKING PRODUCTS!
www.camdencontrols.com
Toll Free: 1.877.226.3369
Page 2 of 5
File: CM-55i Manual. indd Rev1
Revised: 05/05/17
Part No:40-82B209
Loading...