CAMDEN CX-ED1410 Installation Instructions Manual
This Package Includes:
1- 4 PIN power connector
4- Wire nuts
5- M5 x 12 mm screws
2- #10 x 1 1/4” wood screws
2- #10-32 x 1/2” screws
2- Mounting brackets
2- Spacers
1- Varistor
1. Description
Camden CX-ED1410 Grade 1 ANSI strike for cylindrical
locksets offer the very best strike quality and performance,
with a stainless steel faceplate provided. The ‘ANSI’ re strike
design delivers unparalleled application exibility, with eld
selectable voltage and fail safe/fail secure operation.
Note: Fire rating applicable only while in fail secure mode.
CX-ED1410
‘ANSI’ Fire Electric Strike
Installation Instructions
BP10200
2. Specifications 3. Dimensions
Voltage
Current Draw
Static Strength
Dynamic Strength
Endurance
Fire Rating
Latch Projection
Mode
Operation
Duty
Dimensions (Body)
12/24V AC/DC
260mA@12V AC/DC
150mA@24V AC/DC
1,500 Lbs.
70 Ft-Lbs.
1,000,000 Cycles (Factory Tested)
250,000 Cycles (UL Verified)
90 minutes (UL verified)
5/8” - 3/4” (16mm - 19mm)
Field Selectable
Fail Safe/Fail Secure
AC-Buzz
DC-Silent
Continuous
3 3/8” H x 1 7/8” W x 1 3/8” D
(86mm x 47mm x 35mm)
1 1/4”
4 7/8”
(124mm)
(32mm)
(16mm)
5/8”
4 1/8”
(105mm)
(35mm)1 3/8”
3 3/8”
(86mm)
(47mm)1 7/8”
1 5/8”
(42mm)
(19mm)
(19mm)
1/2”
3/4”
3/4”
(35mm)1 3/8”
(12mm)
(35mm)1 3/8”
(32mm)1 1/4”
(3mm)1/8”
Page 1 of 3
4. Installation
CX-ED1410 ‘Universal’ Fire Electric Strike
1. Prepare the door jamb as per the appropriate drawing.
2. Install mounting brackets to jamb using M5x12 screws
and pressed metal nuts. Do not tighten.
3. Spacers are used to assure ush nal assembly of
faceplate into jamb. Add one or more spacers between
jamb and mounting bracket when face plate extends
beyond the jamb. When the faceplate sits inside the
jamb, spacers must be added between the mounting
Mounting Bracket (2pcs)
Drill & Countersink For
M5 Flat-Head Screw (2pcs)
Pressed Metal Nut
M5x12
Flat-Head
Screw (4pcs)
86
35
48
37
126
155
bracket & the lip bracket. Make sure the clearance hole in
the spacer aligns with the hole in mounting bracket.
4. Connect wires coming from the low voltage side of the
transformer to wires (black) from strike.
5. Install electric strike jamb by attaching with # 10-32
screws and lockwashers.
6. Securely tighten the M5x12 screws holding the mounting
brackets to jamb.
Centerline
Jamb
Vertical Centerline
Note: The products are intended to be installed in
accordance with the installation wiring diagram, mechanical
assembly drawings provided with each product, the local
authority having jurisdiction (AHJ) and the National Electric
Code, NFPA 70. When installed in fail secure mode, the
local authority shall be consulted with regard to the use of
possible panic hardware to allow emergency exit from the
secure area.
The electric door strike shall be installed in such a way
and in such location so as to not impair the operation of
an emergency exit device or panic hardware mounted on
the door.
Horizontal
Centerline
Jamb
35
86
Vertical Centerline
48
37
126
105
M5x12
Flat-Head
Screw (2pcs)
Page 2 of 3
Loading...