CAMDEN CX-ED1079L, CX-ED1079DL Installation Instructions Manual

This Package Includes:

1- 4 PIN power connector

1- 3 PIN door status
connector

1- ESP1B, ESP3B and
ESP4B faceplates

4- Wire nuts

5- M5 x 12 mm screws

1. Description

2- #10 x 1 1/4” wood screws

2- #10-32 x 1/2” screws

2- Mounting brackets

2- Spacers

1- Varistor

CX-ED1079L/DL

‘Universal’ Electric Strike

Installation Instructions

UL 1034
UL 294

Camden CX-ED1079L/DL Grade 1 ANSI strikes for cylindrical
locksets offer the very best strike quality and performance,
with three stainless steel faceplates provided. The ‘Universal’

strike design delivers unparalleled application exibility, with
eld selectable voltage, fail safe/fail secure operation and

mechanical adjustment of the strike body.

2. Specifications

Voltage

Current Draw

Static Strength

Dynamic Strength

Endurance

Mode

Mech. Adjustment

Operation

Duty

12/24V AC/DC

260mA@12V DC
150mA@24V DC

1,500 Lbs.

70 Ft-Lbs.

1,000,000 Cycles (Factory Tested)
250,000 Cycles (UL Verified)

Field Selectable
Fail Safe/Fail Secure

Strike Body/Faceplate

AC-Buzz, DC-Silent

Continuous

UL 294 Performance Levels

- Line Security = Level I

- Attack Level = Level I

- Endurance Level = Level IV

- Standby Power = Level I

3. Dimensions

5/8”

(16mm)

4 1/8”

(104mm)

4 7/8”

(123mm)

1 7/32”

(31mm)

1 3/8”

(35mm)

1 3/4”

(44mm)

1 1/4”

(32mm)

1 5/8”

(42mm)

3/4”

(19mm)

Latch Bolt Monitor

SPDT, 100mA @ 24V DC

Dimensions (Body) CX-ED1079L:

3 3/8” H x 1 3/4” W x 1 7/32” D
(86mm x 44mm x 31mm)

CX-ED1079DL:
3 3/8” H x 1 3/4” W x 1 3/8” D
(86mm x 44mm x 35mm)

Page 1 of 3

3 3/8”

(86mm)

CX-ED1079L

1/8”

(3mm)

3 3/8”

(86mm)

(3mm)

CX-ED1079DL

1/8”

(32mm)

1 7/32”

(31mm)

1 3/8”

(35mm)

1 1/4”

1/2”

(12mm)

CX-ED1079L

CX-ED1079DL

4. Installation

Jamp

CX-ED1079L/DL ‘Universal’ Electric Strike

1. Prepare the door jamb as per the appropriate drawing.

2. Install mounting brackets to jamb using M5x12 screws

and pressed metal nuts. Do not tighten.

3. Spacers are used to assure ush nal assembly of

faceplate into jamb. Add one or more spacers between

jamb and mounting bracket when face plate extends

beyond the jamb. When the faceplate sits inside the
jamb, spacers must be added between the mounting

Mounting Bracket

Spacer

Spacer (Option)

M5x12 Flat-Head Screw (2pcs)

Spacer

bracket & the lip bracket. Make sure the clearance hole in
the spacer aligns with the hole in mounting bracket.

4. Connect wires coming from the low voltage side of the
transformer to wires (black) from strike.

5. Install electric strike jamb by attaching with # 10-32
screws and lockwashers.

6. Tighten secure M5x12 screws holding mounting brackets

to jamb.

4 7/8”

(124mm)

3 1/2”

(89mm)

4 1/8”

(105mm)

ESP1B + ESP2B

DL:

L:

1 7/32”

(31mm)

1 3/8”
(35mm)

3 3/8”

(86mm)

M5x12 Screw

Vertical Centerline

Note: The products are intended to be installed in accordance
with the installation wiring diagram, mechanical assembly
drawings provided with each product, the local authority having
jurisdiction (AHJ) and the National Electric Code, NFPA 70.
When installed in fail secure mode, the local authority shall be
consulted with regard to the use of possible panic hardware to
allow emergency exit from the secure area.

The electric door strike shall be installed in such a way and
in such a location so as to not impair the operation of an
emergency exit device or panic hardware mounted on the door.

DL:

DL:

L:

L:

1 7/32”

(31mm)

1 3/8”
(35mm)

1 7/32”

(31mm)

1 3/8”
(35mm)

3 3/8”

(86mm)

3 3/8”

(86mm)

1 3/8”

(35mm)

5 11/16”

(144mm)

6 1/8”

(155mm)

ESP3B

(200mm)

6 3/8”

(168mm)

7 3/8”

(187mm)

6 7/8”

(173mm)

7 7/8”

ESP4B

Page 2 of 3