Camden CM-30 User Manual

r

V

t

t

t

5151 Everest Dr., Unit #6, Mississauga, ON L4W 2Z3
Telephone: [phone] Fax: [phone]
Toll-Free: 1-877-226-3369
Web: www.camdencontrols.com

Section 1 __________________
General Description

Camden CM-30 series illuminated Exit switches are
designed to mount into a deep style single gang
electrical box

The large 2” square translucent button is easy to
push. One momentary micro switch is provided with
Form C output, rated at 10 amps @ 125 VAC.

Standard models are supplied with a 12 – 24
AC/DC light bulb, which is accessed through the fron
or rear. LED models are supplied with either 12V or,
24V long-life LED’s. 24V models are supplied with
an inline resistor, which must not be removed.

Section 2__________________
Installation

Mounting

1. Push the colour-coded leads onto the switch
terminals (if not already installed), as per the
enclosed diagram. If illumination is not required,

Red & Black wires can be removed (no

the
recommended on 24V LED models).

2. Connect the appropriate wires to your devices.
Tuck wiring into box, and fasten switch plate
using screws provided.

NOTE: For 12V light (bulb) operation, cut the Red
wire just before the Inline resistor. For 24V ligh
(bulb) operation, leave the resistor in place.
(This instruction does not apply to LED version).

C M – 3 0

EXIT SWITCH

Installation Instructions

MADE IN CANADA PAGE 1 OF 1

Section 3_________________
Technical Data

Models CM-30E | CM-30H

Lens Colour Green Lens | Blue Lens
Legend “Push to Exit” | Handicap
Size 4.5” H x 2.75” W x 2” D
Mounting 2 x #6-32 machine screws
Switch Rating 10 amps @ 125 VAC
Electrical life 100,000 @ rated capacity

Technical Data Standard Light bulb
Voltage required 12 - 28 V AC/DC
(see note re: resistor)
LED Models
Voltage required 12 V AC/DC, or
24 V AC/DC

Section 4_________________
Warranty

Camden Door Controls Inc. guarantees the
CM-30 to be free from manufacturing defects for 3
years from date of sale. If during the first 3 years
the CM-30 fails to perform correctly, it may be
returned to our factory where it will be repaired o
replaced (at our discretion) without charge. There
is no warranty for LED damage due to over voltage!
Except as stated herein, Camden extends no
warranties expressed or implied regarding function,
performance or service.

Questions?

Call us toll-free at 1-877-226-3369

Filename: CM-30 Instructions.doc
Revision: 6/5/06 3:47 PM

Normally

Closed

Normally

Open

Common

Note:
Location of Inline
Resistor. (24 Volt LE D
models and 12/24
Bulb models only.)
See notes below...

Orange

Blue

Rear View of CM-30 switch
and Faceplate

Grey

Red Black

12 - 24 V

AC/DC

Power

for Light

NOTES:

1. Access to light bulb (or LED) is obtained by first
removing Che rr y sw itch from two plas tic retaining
pins. Then squeeze white retainer assemb ly
between finger and thumb, and gently rock back
and forth while pulling free of black threaded
portion. Then simply pull out light bulb (or LED) to
replace.

2. Re-installati on is reverse of above sequence.
The LED is not polarity sensiti ve. (Similar to bulb).

3. For 12V light bulb operation only, cut off inline­resistor (on Red wire). For 24V bulb or LED
operation, leave resistor in place.

Camden Manufacturing

SCALE: NONE

DRAWING No: DRG-CM30-022503

DRAWN BY: DGW

CM-30 Switc h Wi rin g Diagram

5151 Everest Dr. Unit 6
Mississauga, Ontario
L4W 2Z3

DATE: 02/25/03

REVISED: 06/05/06

FILENAME: CM-30 Diagram.vsd