Camden CM-110SK User Manual

Download

Page 1

1. Packing List

CM-110SK

Standalone Keypad

Installation Instructions

Qty Name

Keypad

User manual

Screwdriver

Wall plugs

Self-tapping screws

Torx screw

Remarks

0.8” x 2.4”Φ(20 mm×60 mm)

0.24” x 1.2”Φ (6 mm×30 mm)

0.16” x 1.1”Φ(4 mm×28 mm)

0.12” x 0.24”Φ(3 mm×6 mm)

2. Description

The CM-110SK is a multifunctional standalone keypad with a wiegand output for interfacing to an access control system. It is suitable for mounting in either indoor or outdoor harsh environments. It is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated case. The electronics are fully potted so the unit is waterproof and conforms to IP68. This unit supports up to 2000 users with a 4 digit PIN. The unit has many extra features including lock output current short circuit protection, wiegand output, and a backlit keypad. These features make the unit an ideal choice for commercial and industrial applications such as factories, warehouses, laboratories, banks and prisons.

1 2

3 4

5 6

[150mm]

7 8

9 0

[44mm]

3. Features

• 2000 users, 4 digit PIN

• Backlit keys

• Zinc Alloy Electroplated anti-vandal case

• Waterproof, conforms to IP68

• Easy to install and program

• Full programming from the keypad

• Can be used as a stand-alone keypad

• Wiegand 26 input for connection to external reader

• Wiegand 26 output for connection to a controller

• Adjustable Door Output time, Alarm time, Door Open time

• Very low power consumption (30mA)

• Fast operating speed, <20ms with 2000 users

• Lock output current short circuit protection

• Built in light dependent resistor (LDR) for anti-tamper

• Built in buzzer

• Red, Yellow and Green LEDS display the working status

Page 1 of 6

Page 2

Standalone Keypad Installation Instructions

4. Quick Reference Programming Guide

To enter programming mode

999999 is the default factory master code

Master Code #

To exit from the programming mode

Note: You must be in programming mode to program the following feature

New Code # New Code

To change the master code

The master code can be 6 to 8 digits

User ID Number # PIN

To add a PIN user

The ID number is any number between 1 & 2000. The PIN is any four digits between 0000 & 9999 with the exception of 1234 which is reserved. Users can be added continuously without exiting programming mode.

2 User ID Number #

To delete a PIN user

Users can be deleted continuously without exiting programming mode.

To unlock the door for a PIN user

Enter the

then press #

5. Speciﬁcations

Operating Voltage

12V DC ±10%

for a PIN user or

User Capacity

Active Current

Idle Current

Lock Output Load

Alarm Output Load

Operating Temperature

Operating Humidity

Waterproof

Adjustable Door Relay time

Adjustable Alarm Time

Wiegand Interface

Wiring Connections

Dimensions

2,000

< 60mA

25±5 mA

Max 3A

Max 20 mA

-49°F to 140°F (-45°C to 60°C)

10% - 90% RH

Conforms to IP 68

0 - 99 seconds

0 - 3 minutes

Wiegand 26 bit

Electric Lock, Exit Button, External Alarm, External Reader

5 15/16” H x 1 3/4” W x 1” D (150 mm x 44 mm x 25 mm)

Page 2 of 6

Page 3

Standalone Keypad Installation Instructions

6. Installation

• Remove the back cover from the keypad using the supplied special screw driver

• Drill 2 holes on the wall for the Self tapping screws and 1 hole for the cable

• Put the supplied wall plugs into the two holes

• Fix the back cover rmly on the wall with the 2 Self tapping screws

• Thread the cable through the cable hole

• Attach the keypad to the back cover

7. Wiring

Color Function Description

Pink BELL_A Doorbell

Pale Blue BELL_B Doorbell

Green D0 Wiegand output D0

White D1 Wiegand output D1

Grey ALARM Alarm negative (alarm positive connected 12 V+)

Yellow OPEN Exit button (the other end connected GND)

Brown D_IN Door Contact switch (the other end connected GND)

Red 12V+ 12V + DC Regulated Power Input

Black GND 12V - DC Regulated Power Input

Blue NO Relay Normally Open

Purple COM Relay Common

Orange NC Relay Normally Closed

Common power supply diagram:

BELL_A PINK

BELL_B PINK

D0 GREEN

D1 WHITE

ALARM GRAY

OPEN YELLOW

D_IN BROWN

+12V RED

GND BLACK

NO BLUE

COM PURPLE

NC ORANGE

Connect

Bell

Alarm

Exibit Button

Door Contact

Fail Secure Lock

Fail Safe Lock

Page 3 of 6

12V

Power supply

Page 4

Standalone Keypad Installation Instructions

8. Reset to Factory Default

a. Disconnect power from the unit

b. Press and hold # key while powering the unit back up

c. On hearing two “Beeps” release # key, system is now back to factory settings

Note: Only the installer data is restored, user data will not be affected.

9. Anti-Tamper Alarm

The unit uses a LDR (light dependent resistor) as an anti-tamper alarm. If the keypad is removed from the cover, the tamper alarm will operate.

10. Sound and Light indication

Operation Status Red Light Green Light Yellow Light Buzzer

Power on

Standby Bright -

Press keypad - -

Operation successful - Bright

Operation failed - -

Enter into programming mode Bright -

In the programming mode - -

Exit from the programming mode Bright -

Open the door - Bright

Alarm Bright -

Bright

- -

Bright

11. Detailed Programming Guide

11.1 User Settings

To enter the programming mode

To exit from the programming mode *

Note that to undertake the following programming, the master user must be logged in

* Master code #

999999 is the default factory master code

Beep

Beep/Beep/Beep

Beep

Alarm

To change the master code

To add a Pin user

0 New code # New code #

The master code can be 6 to 8 digits long

1 User ID number # PIN #

1 User ID no 1 # PIN # User ID no 2 # PIN #

Page 4 of 6

Page 5

Standalone Keypad Installation Instructions

To delete a PIN user

To change the PIN of a PIN user

(This step must be done out of programming mode)

To delete All users

To delete ALL users. Note that this is a dangerous option so use with care

To unlock the door

For a PIN user

11.2 Door Settings

Relay Output Delay Time

To set door relay strike time

Door Open Detection

2 User ID number # Users can be deleted continuously without exiting programming mode

* ID number # Old PIN # New PIN #

New PIN #

2 0000 #

Enter the PIN then press #

* Master code # 4 0~99 # *

0-99 is to set the door relay time 0-99 seconds

Door Propped Open Alarm. When used with an optional magnetic contact or built-in magnetic contact of the lock, if the door is opened normally, but not closed after 1 minute, the inside buzzer will beep automatically to remind people to close the door and continue for 1 minute before switching off automatically.

Door Forced Open Alarm. When used with an optional magnetic contact or built-in magnetic contact of the lock, if the door is opened by force, or if the door is opened after 20 seconds of the electro-mechanical lock not being closed properly, the inside buzzer and alarm output will both operate. The Alarm Output time is adjustable between 0~3 minutes with the default being 1 minute.

To disable door open detection. (Factory default) 6 0 #

To enable door open detection 6 1 #

Alarm output time

To set the alarm output time (0~3 minutes) Factory default is 1 minute

Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes, or the alarm will operate for 10 minutes, depending on the option selected below.

Normal status: No keypad lockout or alarm (factory default)

Keypad lockout enable 7 1 #

Alarm and inside buzzer operate 7 2 #

5 0~3 #

7 0 # (Factory default setting)

To remove the alarm

To reset the Door Forced Open Alarm Master Code #

To reset the Door Propped Open Alarm

Close the door or Master Code #

Page 5 of 6

Page 6

Standalone Keypad Installation Instructions

12. The unit operating as a Wiegand Output Reader

In this mode the unit supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any controller which supports a Wiegand 26 bit input.

BELL_A PINK

BELL_B PINK

GREEN

Bell

ALARM GRAY

OPEN YELLOW

D_IN BROWN

+12V RED

GND BLACK

NO BLUE

COM

Connect

WHITE

Access Controller

PURPLE

ORANGE

12.1 Keypad 8 bit Burst Mode

Every key pressed generates an 8 bit data stream that is transmitted over the wiegand bus.

Key Output Key Output

1 11100001

2 11010010

3 11000011

4 10110100

5 10100101

11110000

6 7 8 9 *

12V

GND

10010110

10000111

01111000

01101001

01011010

01001011

Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control

5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7

www.camdencontrols.com Toll Free: 1.877.226.3369

Page 8 of 6

File: Standalone Keypad Installation Instructions.indd R1 Revision: 25/01/2016 Part No.: 40-82B191