Page 1
TECHNICAL SPECIFICATIONS
© Cambridge Audio 2014
Cambridge Audio is a brand of Audio Partnership Plc,
Registered Office: Gallery Court, Hankey Place, London SE1 4BB,
United Kingdom, Registered in England No. 2953313
www.cambridgeaudio.com
Cambridge Audio’s policy is one of continuous improvement.
Design and specifications are therefore subject to change without prior notice.
Minx Satellites Specifications
Min 12 and Min 22
I Min 12 uses a single BMR (Balanced Mode Radiator) full
range driver, combining bending wave technology for
higher frequencies, with pistonic driver movement for lower
frequencies
I Min 22 uses the BMR driver combined with an additional,
dedicated woofer for further improved bass handling
I Incredibly wide dispersion from the BMR driver virtually
eliminates any ‘sweet spot’ problem
I BMR technology offers wide frequency response
from a single driver, allowing for optimum integration
with a subwoofer
Min 12 specifications Min 22 specifications
Sensitivity (SPL) 86dB (2.83 Vrms input)
Frequency response 150Hz-20kHz
Impedance 8 Ohms compatible
Recommended Amp Power 25 - 200W*
Drivers 1 x 2.25” BMR
Dimensions (H x W x D) 78 x 78 x 85mm
(3.1 x 3.1 x 3.3”)
Weight 0.43kg (0.95lbs)
Finishes High gloss black
High gloss white
I Acoustically damped thermo polymer and extruded
aluminium cabinet construction ensuring a rigid speaker
cabinet to disperse colouration
I Scratch resistant high gloss lacquer available in black
or white finishes
I Optional table top or floor stands available
Sensitivity (SPL) 88dB (2.83 Vrms input)
Frequency response 120Hz-20kHz
Impedance 8 Ohms compatible
Recommended Amp Power 25 - 200W*
Drivers 1 x 2.25” BMR
Dimensions (H x W x D) 154 x 78 x 85mm
Weight 0.75kg (1.65lbs)
Finishes High gloss black
1 x 2.25” longthrow woofer
(6.0 x 3.1 x 3.3”)
High gloss white
* Using a high powered amplifier lower down its volume scale results in lower distortion and better sound. Of course if you hear a distorted sound or mechanical ‘crack’ as the speakers hit their
end stops, you are playing the speakers too loud and this may cause damage. With an AVR the Min 12/22 speakers should be set to ‘small’ with a crossover frequency of 140kHz. In this
configuration, power handling is considerably increased.
Page 2
TECHNICAL SPECIFICATIONS
© Cambridge Audio 2014
Cambridge Audio is a brand of Audio Partnership Plc,
Registered Office: Gallery Court, Hankey Place, London SE1 4BB,
United Kingdom, Registered in England No. 2953313
www.cambridgeaudio.com
Cambridge Audio’s policy is one of continuous improvement.
Design and specifications are therefore subject to change without prior notice.
Minx Subwoofer Specifications
cm
5.5
3
3
3
0.5
3
8
2
25.5
23
20.5
8
1
5.5
1
3
1
0.5
1
8
X201 X301
X201 and X301
I Powerful DSP design delivering awesome performance
from the smallest footprint possible
I Powerful 200W and 300W digital amplifiers
I One piece aerospace grade aluminium cones move air with
incredible efficiency
Inches
4"
1
3"
1
2"
1
1"
1
10"
9"
8"
"
7
"
6
"
5
"
4
3"
2"
1"
I Scratch resistant high gloss lacquer available in
black or white finishes
I DSP design allows far smaller cabinet construction than
comparative subwoofers
I Supplied with removable grilles
I Full rear panel control of gain, phase and crossover
frequency allowing optimum integration and room
positioning
I Driver plus ABR (Auxillary Bass Radiator)
configuration. ABRs replace bass ports to eliminate
air noise at high levels
X201 specifications X301 specifications
Power Output 200W
Frequency Response 36Hz (-6dB) – 200Hz
Crossover Active – variable 50Hz-200Hz
Drivers 1 x 6.5" subwoofer
2 x 6.5" passive radiator
Dimensions 219 x 210 x 222mm
(H x W x D) (8.6 x 8.3 x 8.7")
Weight 5.0Kg (11.0lbs)
Finishes High gloss black
High gloss white
Power Output 300W
Frequency Response 31Hz (-6dB) – 200Hz
Crossover Active – variable 50Hz-200Hz
Drivers 1 x 8" subwoofer
Dimensions 311 x 266 x 278mm
(H x W x D) (12.4 x 10.5 x 11.0")
Weight 7.5Kg (16.5lbs)
Finishes High gloss black
1 x 8" passive radiator
High gloss white
Loading...